Abstract:Abstract Gravity settling represents the main oil-water separation mechanism. Many separation plants rely only on gravity settling with the aid of demulsifiers (direct or reverse breakers) and other chemicals such as water clarifiers if they are required. Yet, other complementary separation methods exist including filtration, flotation, and centrifugation. In terms of results and more specifically with respect to the separated produced-water, the main threshold on its quality is the dispersed oil content. Even with zero discharge and reinjection into hydrocarbon formations, the presence of residual oil in the aqueous phase represents a concern. High oil content results into formation damage and losses in injectivity which necessitates formation stimulations and hence additional operational expenses. In this work, we investigated the effects of different separation techniques on separated water quality. In addition, we studied the impact of enhanced oil recovery (EOR) chemicals on the different separation techniques in terms of efficiency and water quality. Based on the results, we identified potential improvements to the existing separation process. We used synthetic well-characterized emulsions. The emulsions were prepared at the forecast water: oil ratio using dead crude oil and synthetic representative brines with or without the EOR chemicals. To clearly delineate and distinguish the effectiveness of different separation methods, we exacerbated the conditions by preparing very tight emulsions compared with what is observed on site. With that, we investigated three separation techniques: gravity settling, centrifugation, and filtration. First, we used Jar Tests to study gravity settling, then a benchtop centrifuge at two speeds to evaluate centrifugation potential. Finally, for filtration, we tested two options: membrane and deep-bed filtrations. Concerning the water quality, we performed solvent extraction followed by UV analyses to measure the residual oil content as well as light transmission measurements in order to compare the efficiency of different separation methods. The results of analyses suggest that gravity settling was not efficient in removing oil droplets from water. No separation occurred after 20 minutes in every tested condition. However, note that investigated conditions were severe, tighter emulsions are more difficult to separate compared to those currently observed in the actual separation plant. On the other hand, centrifugation significantly improved light transmission through the separated water. Accordingly, we can conclude that the water quality was largely improved by centrifugation even in the presence of EOR chemicals. In terms of filtration, very good water quality was obtained after membrane filtration. However, significant fouling was observed. In the presence of EOR chemicals, filtration lost its effectiveness due to the low interfacial tension with surfactants and water quality became poor. With deep-bed filtration, produced water quality remained good and fouling was no longer observed. However, the benefits from media filtration were annihilated by the presence of EOR chemicals. Based on these results and at least for our case study, we conclude that centrifugation and deep-bed filtration techniques can significantly improve quality of the separated and eventually reinjected water. In terms of the effects of EOR chemicals, the performance of centrifugation is reduced while filtrations are largely impaired by the presence of EOR chemicals. Thereby, integration of any of the two methods in the separation plant will lead to more efficient produced-water reinjection, eliminating formation damage and frequent stimulations. Yet, it is important to note that economics should be further assessed.

Environmental trade-offs in energy production: A review of the produced water life cycle and environmental footprint

Produced Water Treatment: Review of Technological Advancement in Hydrocarbon Recovery Processes, Well Stimulation, and Permanent Disposal Wells

Environmental impacts related to drilling fluid waste and treatment methods: A critical review

Review of oilfield produced water treatment technologies

Oil Based Drilling Fluid Waste: An Overview on Environmentally Persistent Pollutants

A review of treatment technologies for produced water in offshore oil and gas fields

Oil field–produced water treatment: characterization, photochemical systems, and combined processes

Petroleum wastewater: Environmental protection, treatment, and safe reuse: An overview

Safe reuse of treated produced water outside oil and gas fields? A review of current practices, challenges, opportunities, and a risk-based pathway for produced water treatment and fit-for-purpose reuse

Methods of Treating Produced Water During Oil and Gas Production Processes

Produced water management - A mathematical model to trade-off economic cost and environmental impact for infrastructure utilisation

Produced Water Quality: The Effects of Different Separation Methods for Water and Chemical Floods

Socio-environmental externalities of sewage waste management

Treatment of drilling fluid waste during oil and gas drilling: a review

Oily Wastewater Treatment: Methods, Challenges, and Trends

Produced Water Treatment with Conventional Adsorbents and MOF as an Alternative: A Review

Review on Water and Energy Integration in Process Industry: Water-Heat Nexus

Fit-for-purpose treatment goals for produced waters in shale oil and gas fields

Beyond treatment technology: Understanding motivations and barriers for wastewater treatment and reuse in unconventional energy production

Treatment of Petrochemical Wastewater and Produced Water from Oil and Gas

Energy consumption and carbon emissions management in drinking water treatment plants: A systematic review