Gastroduodenocolic fistula due to a benign gastric ulcer, case report.

J. Briggs,W. Boswell

Abstract:

What problem does this paper attempt to address?

A Novel Laser Ultrasonic Thickness Measurement Method for Metal Plate Based on Spectral Analysis

Yongqiang Liu,Shixi Yang,Chunbiao Gan

DOI: https://doi.org/10.1109/urai.2015.7358964

2015-01-01

Abstract:Thickness measurement is highly useful in industrials both for controlling the thickness of the product and for material characterization considering both mechanical and chemical properties. Longitudinal ultrasonic velocity can be used to measure material thickness provided that sufficient accuracy can be achieved. A new laser ultrasonic thickness measurement method based on spectral analysis was proposed in this paper and was used for accurate thickness measurement for metal plate. A one-layer model was introduced which laser ultrasonic transmits into, deducing the expression of ultrasonic reflection coefficient amplitude spectrum (URCAS), from which we obtained the method for metal plate thickness measurement; then a laser ultrasonic system was set up to receive the laser ultrasonic transmitting into the plate. Meanwhile we developed a new laser ultrasonic data processing algorithm so that the frequency values of the peaks in frequency domain could be easily identified, then the velocity of the longitudinal ultrasonic could be calculated by the frequency difference of two adjacent peaks; finally, based on the velocity of the longitudinal ultrasonic and the experiment data the thickness of the metal plate could be calculated by inversion algorithm. The relative errors of the thickness measurement were below 0.66% for 5052 aluminum alloy; also we found that, the measurement of thickness is more accurate as the alloy thickness decreases.
A Study of Inner Crack Testing with the Laser Phased Array Method.

Xuekun Liu,Shixi Yang,Chunbiao Gan

DOI: https://doi.org/10.1109/urai.2016.7734093

2016-01-01

Abstract:As the optical penetration depth and thermal diffusion effect are small, shear waves and longitudinal waves generated by a laser pulse in thermoelastic regime are generally weak in metallic materials. The method of laser ultrasonic is rarely applied to inspect the inner cracks. In this paper, phased array laser ultrasonic is developed to focus and steer shear waves and longitudinal waves, and obtain inner crack characteristics. Firstly, a two-dimensional laser phased array finite element model is established. Secondly, based on this model, a study on numerical simulation of interaction between shear waves and cracks is conducted by adjusting time delay of laser phased array. It is found by analysis that the position of cracks can be determined by monitoring changes of polarity of shear-tip-shear (STS) diffraction received on the surface of metallic materials and the depth of cracks can be determined by the time of flight of STS diffraction and shear-tip-longitudinal (STL) diffraction. Last of all, a study on numerical simulation of interaction between longitudinal waves and cracks is also conducted. This study provides a possible method for the detection of inner cracks in metallic materials.
Laser-induced thermal damage detection in metallic materials via acoustic emission and ensemble empirical mode decomposition

Zhensheng Yang,Zhonghua Yu,Haixi Wu,Daofang Chang

DOI: https://doi.org/10.1016/j.jmatprotec.2014.03.009

IF: 6.3

2014-01-01

Journal of Materials Processing Technology

Abstract:A detection method of laser-induced thermal damage–surface burn, rehardening and residual stress, was studied in this work. Artificial thermal damage was produced to various steels, e.g., AISI 1045, ASTM A36 and AISI 304, by virtue of laser irradiation. The aim of the present work is to identify thermal damage through sensor and feature extraction techniques. Acoustic emission(AE) sensor and ensemble empirical mode decomposition(EEMD) method were employed for this purpose. A de-noising method was proposed to eliminate noises from original AE signals, based on EEMD. Quantified thermal damage features were obtained. Results evidenced a strong correlation between AE features, i.e., RMS value of the reconstructed acoustic emission signal, and surface burn, residual stress value, as well as hardness of steels. The present work could be used as a potential and indirect approach for thermal damage detection.
Investigation of pipe thickness monitoring using the shear wave EMAT technology with high lift-off distance

Xian-bin HUANG,Yang ZHAO,Yang JU,Jiang-feng SONG,Jian-wei CHEN,Rui GUO,Gang-yang NAN,Qi-wu WANG

DOI: https://doi.org/10.3976/j.issn.1002-4026.2018.02.009

2018-01-01

Abstract:To solve the problem of pipe thickness on-line nondestructive testing in the explosive surroundings of oil refinery area,a novel EMAT system with maximum lift-off value of 6 mm has been developed in the way of focusing magnetic field and optimizing the testing coil.Experiment results show that the testing accuracy was less than 0.05 mm for standard test block with thickness of 22 mm and the serviced pipeline with thickness of 12.16 mm when the condition of lift-off value was less than 6 mm.The developed EMAT system in this work can satisfy the requirement of pipeline thickness detection in the refining factory,which provides the ability of explosion-proof design and certification for EMAT technology.
Optimization design of laser-EMAT and its application in high-temperature forgings detection

Lingxiao Meng,Wenze Shi,Chao Lu,Guo Chen,Fasheng Qiu,Ying Zhu,Yuan Liu,Shuanglin Guo

DOI: https://doi.org/10.3233/jae-230003

2023-06-07

International Journal of Applied Electromagnetics and Mechanics

Abstract:In high-temperature continuous forging process, according to the real-time monitoring of workpiece thickness and flaws, the processing parameters can be adjusted accordingly, so we can remove defective components in time, which has essential research value for avoiding the interruption of production line and improving their yield and quality grade. We established a finite element (FE) model of the carbon steel's laser-electromagnetic acoustic transducer (laser-EMAT) testing process. Based on the simulation model, we analyzed the effects of laser parameters, EMAT parameters, and sample thickness on the detected ultrasonic signal amplitude, and we also achieved the optimized Laser-EMAT design parameters. Subsequently, we developed a high-temperature resistant spiral coil EMAT and measured the high-temperature forging with a thickness of 100 mm and temperatures from 300 °C to 730 °C. Based on the experiments, we researched the effect of specimen temperature on the received ultrasonic wave amplitude. The results show that the excitation efficiency of laser-induced ultrasonic waves improves by decreasing pulse duration, decreasing laser spot radius, and increasing pulse laser energy. The receiving efficiency of the shear wave (SW) detected by the EMAT enhances when reducing the diameter of the EMAT wire and increasing the permanent magnet height. When the radius of the permanent magnet is equal to the radius of the EMAT coil, the receiving efficiency of SW is the highest. As the sample thickness increases, the size of the EMAT should increase accordingly to the acoustic beam divergence for obtaining a higher ultrasonic wave intensity. The amplitude of the SW signal received by the EMAT increases by 679% after the optimization design. With rising carbon steel forging temperature, the SW signal amplitude increases first and then decreases sharply, reaching its maximum at 617 °C, which is 29% higher than at room temperature, and the signal-to-noise ratio (SNR) of the SW is 20.5 dB.

mechanics,engineering, electrical & electronic,physics, applied
Study on the Laser-EMAT Integrated System for Simultaneously Measuring the Width and Depth of Metal Plate

Wei Yuan,Ze Liu,Yong Li,Jiwei Huo,Yadong Wang

DOI: https://doi.org/10.1109/jsen.2020.3040996

IF: 4.3

2021-01-01

IEEE Sensors Journal

Abstract:A non-contact Laser-EMAT integrated system (LEIS) that uses a pulse laser as a generator and an Electromagnetic acoustic transducer (EMAT) as a detector is proposed. To explain the LEIS could simultaneously measure the width and the depth of metal plate, the finite element model (FEM) of the LEIS, which can describe the entire process from laser generates ultrasound to EMAT receives ultrasound, is established. In detail, the intensity ratios of Rayleigh wave, Shear wave and Longitudinal wave excited by laser under the consideration of three components, the particle displacement, the particle vibration velocity in out-plane direction and particle vibration velocity in in-plane direction, are focused. Combining the characteristics of the ratio and the EMAT as a velocity sensor, the Rayleigh wave and Longitudinal wave in the case of the particle vibration velocity in out-plane direction are chosen as the using waveforms, and the changes of directivity of various waveforms with laser parameters are studied. Furthermore, after the coil structure parameters and magnetic field direction of EMAT were reanalyzed and reconsidered, it is decided to use the coil with the wire spacing of 0.1 mm and a number of turns of 8 to combine with the transverse magnetic field to simultaneously detect the Rayleigh wave and Longitudinal wave generated by the laser. Finally, the signal-to-noise ratio of the two waveforms reach a balanced value, and can be clearly distinguished and extracted to achieve the purpose of measuring the depth and width of the metal plate at the same time.
Simultaneous Thickness, Velocity, Density, and Attenuation Measurement of a Thin Layer by Time-Resolved Acoustic Microscopy

Jian Chen,Xiaolong Bai,Keji Yang,Bingfeng Ju,Jianxing Meng

DOI: https://doi.org/10.1121/1.4755238

2012-01-01

The Journal of the Acoustical Society of America

Abstract:An ultrasonic method for simultaneous determination of thickness, velocity, density and attenuation of thin layer using a time-resolved acoustic microscopy is proposed. Reflection from the thin layer is represented as a function of three dimensionless parameters which are determined from the experimentally normal incidence component of the two dimensional reflection spectrum R(θ,ω) derived based on the inversion of V(z,t) technique with time-resolved acoustic microscopy. The thickness of the thin layer is derived from the signals received from the layer itself considering the geometrical relations when the lens focused on the sample’s surfaces. The simultaneous determination of thickness, velocity, density and attenuation of thin stainless steel plate by using a point-focusing transducer with nominal frequency of around 50MHz were carried out. The determined material properties are comparable, in which the thickness, velocity and density can be measured with a percentage biases less than 5% and the attenuation is close to its real value. The present preliminary work shows the high efficiency, viability and capability of the new non-destructive technique in simultaneously characterize basic mechanical and geometrical properties of thin layers.
Efficient Fault Tolerant Algorithms for Internet Distributed Systems

Swati Mishra,S. K. Panda

DOI: https://doi.org/10.4018/IJKDB.2017010106

International Journal of Knowledge Discovery in Bioinformatics

Abstract:In the current era, Internet is the fastest growing technology. It is a global network of distributed systems that interconnects with each other to share various resources and computation. The complexity of the distributed systems is rapidly increasing, which leads to an increased susceptibility of failure to the participating computers such as clients and servers and their interconnections. Therefore, the main challenge is to address such failures and develop efficient algorithms to tolerate such failures. In this paper, four fault tolerant algorithms, namely server-based fault tolerant SFT, client-based fault tolerant CFT, client-server fault tolerant CSFT and connection fault tolerant CoFT are proposed to deal with the above challenge. The proposed algorithms are evaluated in terms of number of failures NOF, load factor LF and load standard deviation LSD and compared with an existing algorithm. The comparison results show the superior performance of the proposed algorithms.
Laser ultrasonic inspection for mechanical properties of materials at high temperature

Jiajian Meng,Weiguang Hou,Xianke Li,Changhao Song,Jianhai Zhang

DOI: https://doi.org/10.1063/5.0147615

IF: 2.877

2023-08-01

Journal of Applied Physics

Abstract:The measurement of mechanical properties of high-temperature resistant materials at high temperatures is particularly critical, and laser ultrasonic non-destructive testing technology is a prospective approach for measuring mechanical properties in high-temperature environments. Laser ultrasonic propagation models are constructed by finite element analysis, which reveals the effects of different excitation mechanisms on acoustic velocity measurements. It is found that the shear wave in the main propagation direction is hardly detected, and the distinction between shear waves and surface waves in the time domain signal is difficult. Based on the conclusions, the relationships between surface waves, longitudinal waves, and mechanical properties of materials are established by theoretical derivation. According to the propagation characteristics of surface waves and longitudinal waves, the eccentricity detection scheme of the same side and the concentricity detection scheme of the opposite side are, respectively, designed. The velocities of surface waves and longitudinal waves are measured, considering the thermal expansion coefficient and density changes with temperature. The mechanical properties of materials at different temperatures (25–1000 °C) are successfully calculated, and the experimental results are well in accordance with the reference values. It gives a reliable basis for efficient measurement of mechanical properties of materials at high temperatures.

physics, applied
High Precision Ultrasonic Measurement Method for Thin-Walled Parts

Hao Chen,Kaipeng Ji,Wei Zhang,Chengqian Zhang,Jianzhong Fu,Peng Zhao

DOI: https://doi.org/10.1016/j.ndteint.2024.103122

IF: 4.683

2024-01-01

NDT & E International

Abstract:Thin-walled parts are extensively utilized in the aerospace industry, where over thinning defects in these parts would significantly compromise mechanical safety. Ultrasound measurement methods are commonly employed for thickness non-destructive testing. Manual calibration of reference signals is usually necessary, negatively impacting automation, robustness, and accuracy. This paper proposes a high-precision ultrasound amplitude method for thin-walled component inspection, getting rid of manual calibration. Firstly, the measured signal is preprocessed to extract the spectrum in the effective frequency range. Then, the spectrum is approximated using the asymmetrical Gaussian amplitude model to estimate the spectrum of reference signal and reflection coefficient. Moreover, initial propagation time is estimated from autocorrelation of the signal. Finally, the accurate thickness is obtained from the numerical calculation of reflection coefficient with the initial time. Simulations and experiments demonstrate that the proposed method can accurately measures metal plates as thin as 0.5mm. Compared to the traditional correlation method, it greatly improves measurement accuracy and stability, reducing them to 1/2 and 1/4 of the latter, respectively. Additionally, the proposed method also demonstrates high accuracy for curved thin plates, with an average relative error of only 0.57%. Furthermore, the method exhibits high levels of automation, robustness, and accuracy, and holds significant potential for thickness detection in thin-walled structural components.
Residual strain measurement based on longitudinal to shear wave velocity ratio with a dual-mode EMAT

Geng Dang,Cuixiang Pei,Zhanfeng Yang,Haiqiang Zhou

DOI: https://doi.org/10.3389/fmats.2023.1273190

2023-12-11

Frontiers in Materials

Abstract:In this paper, a new and noncontact method with measuring longitudinal to shear wave velocity ratio by a dual-mode electromagnetic acoustic transducer is proposed for residual strain measurement in a metal structure without knowing its thickness. Firstly, the theoretical derivation of the ratio of longitudinal and shear wave velocities in electromagnetic ultrasound was conducted, and based on this, the effectiveness of the dual-mode bulk wave electromagnetic acoustic transducer was simulated. Secondly, the longitudinal and shear wave velocities of uniaxial stretched aluminum plates with different residual strains were measured using the established electromagnetic ultrasound experimental system. Finally, the ratio of longitudinal and shear wave velocities of specimens with different plastic deformations was analyzed, achieving quantitative non-destructive testing of residual strain in uniaxial tensile aluminum plates.

materials science, multidisciplinary
Thickness Measurements with EMAT Based on Fuzzy Logic

Yingjie Shi,Shihui Tian,Jiahong Jiang,Tairan Lei,Shun Wang,Xiaobo Lin,Ke Xu

DOI: https://doi.org/10.3390/s24134066

IF: 3.9

2024-06-22

Sensors

Abstract:Metal thickness measurements are essential in various industrial applications, yet current non-contact ultrasonic methods face limitations in range and accuracy, hindering the widespread adoption of electromagnetic ultrasonics. This study introduces a novel combined thickness measurement method employing fuzzy logic, with the aim of broadening the applicational scope of the EMAT. Leveraging minimal hardware, this method utilizes the short pulse time-of-flight (TOF) technique for initial thickness estimation, followed by secondary measurements guided by fuzzy logic principles. The integration of measurements from the resonance, short pulse echo, and linear frequency modulation echo extends the measurement range while enhancing accuracy. Rigorous experimental validation validates the method's effectiveness, demonstrating a measurement range of 0.3–1000.0 mm with a median error within ±0.5 mm. Outperforming traditional methods like short pulse echoes, this approach holds significant industrial potential.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Research on Identification and Detection of Aluminum Plate Thickness Step Change Based on Electromagnetic Acoustic Resonance

Zhichao Cai,Yihu Sun,Zhengshi Lu,Qixiang Zhao

DOI: https://doi.org/10.3390/magnetochemistry9030086

2023-03-23

Magnetochemistry

Abstract:The conventional ultrasonic thickness measurement method is ineffective in detecting the measured specimen with a step change in thickness as it is easy to cause multimode acoustic mixing in the ultrasonic detection process. To solve this problem, this paper presented an electromagnetic acoustic resonance (EMAR) moving scan identification method based on a frequency–frequency energy density precipitation (FFEDP) algorithm, which uses a standing wave resonance mode to accurately extract step thickness information and employs the algorithm to separate step thickness information. According to the simulation results, the ratio of the highest energy density of the spectrum signal on both sides of the step area to the total energy density had an opposite linear change rule with the equidistant movement of the transducer coil. The thickness step area can be identified by analyzing the crossover point of the contrast value change. The experimental results showed that the proposed method can accurately extract the thickness information under millimeter-level stepping distance for sector-notched specimens with step surfaces of different thicknesses, and at the same time realize the effective identification of the step surface.

chemistry, physical, inorganic & nuclear,materials science, multidisciplinary
Improving laser-EMAT ultrasonic energy conversion efficiency using surface constraint mechanism

Wenze Shi,Yanshan Tong,Chao Lu,Yao Chen,Gongtian Shen,Guangdeng Zeng

DOI: https://doi.org/10.1016/j.ultras.2022.106729

IF: 4.2

Ultrasonics

Abstract:To address the problem of low signal-to-noise ratio (SNR) of ultrasonic echo generated by laser-electromagnetic acoustic transducer (EMAT) ultrasonic method in metal materials, a method to improve the energy conversion efficiency of laser-EMAT ultrasonic testing using the surface constraint mechanism is proposed. Based on numerical simulation and experiment, the excitation mechanism of a laser surface heat source with and without a surface constraint mechanism is investigated, and the effect of the water film surface constraint on the laser-EMAT ultrasonic testing echo of different metal materials is analyzed. The effects of laser spot radius, laser power density, laser pulse duration, EMAT design parameters, and water film parameters on the ultrasonic echo amplitude and multimode ultrasonic energy distribution ratio are also investigated, and the optimal combination of laser excitation and EMAT reception parameters is provided. The results show that the laser power density and spot radius significantly affect the multimode ultrasonic amplitudes. Under the water film surface constraint, the energy distributions of shear waves (SWs) and longitudinal waves (LWs) change significantly, and the energy of the SW change rules of different metal materials are different. After using the surface constraint mechanism, the LW amplitude improves significantly, and the SNR of the LW is increased by at least 13.0 dB, the main bang duration is reduced by at least 29.4%, and the main bang amplitude is reduced by more than 80.5%. The relevant information of the surface constraint mechanism provides an effective reference for designing the laser-EMAT testing system with LW detections and reducing the dead zone in ultrasonic testing.
Easy-to-operate thickness measurement method for steel plate using bulk-wave EMAT

Zhiling,Ye,Zandong,Han,Dong,Du

2018-01-01

Abstract:The electromagnetic acoustic transducer (EMAT) method, due to its couplant-free feature, is crucial to defects detection during the in-line inspection of steel pipelines. However, different EMAT approaches require particular analysis under specific testing situation. To solve this problem, an easy-to-operate bulk-wave EMAT is adopted to measure the thickness of the steel plate in this paper. The EMAT set-up basically contains a single permanent magnet and a spiral coil. Experiments are conducted on manual defects with depth and width differences. The EMAT signal processing and analysis on different testing conditions is described, where a denoising algorithm is applied to the original inspection data. The results of the method proposed show that it has great potential to precisely measure thickness on steel pipelines.
An Advanced Magnetoacoustic Compound Inspection Method of High-Order Mode EMAT

Xin Zhao,Zenghua Liu,Yanhong Guo,Cunfu He,Bin Wu

DOI: https://doi.org/10.1109/jsen.2021.3130121

IF: 4.3

2022-01-01

IEEE Sensors Journal

Abstract:In this study, an advanced magnetoacoustic compound inspection method for a high-order Lamb waves mode electromagnetic acoustic transducer (EMAT) was proposed. The proposed EMAT can achieve the excitation and reception of the A1 mode which is the first-order Lamb waves mode. According to the characteristics of the A1 mode EMAT testing signal, a signal processing method for obtaining the pulsed eddy current signal by curve fitting was developed to extract the information for the pulsed eddy current. The voltage of the ultrasonic waves was carried on the pulsed eddy current voltage, and it was obtained by removing the pulsed eddy current voltage and extracting the time-domain testing signal of the A1 mode EMAT. Through A1 mode EMAT single detection that was used to obtain the pulsed eddy current and A1 mode, the multi-parameter from the magnetoacoustic compound testing signal of the A1 mode EMAT could be used to characterize the aluminum plate performance degradation. The detection accuracy of aluminum plate performance degradation was improved by the magnetoacoustic compound inspection compared with a single detection method.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
An improved steady-state method for measuring the thermal contact resistance and bulk thermal conductivity of thin-walled materials having a sub-millimeter thickness

Biao Feng,Jing Tu,Yu-Hong Zhang,Li-Wu Fan,Zi-Tao Yu

DOI: https://doi.org/10.1016/j.applthermaleng.2020.114931

IF: 6.4

2020-01-01

Applied Thermal Engineering

Abstract:Thin-walled materials, such as alloys, polymers, and glasses, with a thickness between 0.1 and 1 mm have been widely utilized in the encapsulation structures of electronic devices (e.g., the shells of laptops, cellphones, and cameras). The thermal contact resistance (TCR) and bulk thermal conductivity of these thin-walled materials are the key parameters for thermal design of electronic devices. In order to measure the TCR of thin-walled materials having a sub-millimeter thickness, an improved steady-state method was proposed in this work, which is based on the ASTM D5470 standard with the improvement being relied on in situ detection on the sample thickness variations. Such an improved apparatus was designed and constructed, which is equipped with a high-precision laser displacement sensor for measuring the sample thickness. Numerical simulations were performed to verify the heat dissipation from the insulated rods and the experimental uncertainties were analyzed. The measured bulk thermal conductivity was compared with those obtained by traditional steady-state, laser flash and transient plane source methods. The overall TCR of thin-walled stainless steel (SS304) was determined to be of the order of 10(-4) m(2).K/W, which was in good agreement with that of bulk SS304 samples having similar surface roughness (TCR = 3.13 x 10 (-4) m(2).K/W).
Ultrasonic on-machine scanning for thickness measurement of thin-walled parts: modeling and experiments

Meng Lian,Haibo Liu,Tongyu Zhang,Qile Bo,Te Li,Yongqing Wang

DOI: https://doi.org/10.1007/s00170-019-04021-5

IF: 3.563

2019-06-25

The International Journal of Advanced Manufacturing Technology

Abstract:The thickness measurement of large thin-walled part has become increasingly important to inspect the machining quality and compensate the machining errors. So far, commercial hand-held ultrasonic thickness gauges have been widely used in the wall thickness inspection of large thin-walled parts. However, the manual operation has some disadvantages such as insufficient measurement efficiency, intensive labor, and limited accuracy. To tackle these problems, an automatic thickness measuring method is supposed to be an effective approach. In this article, an ultrasonic on-machine scanning technique for thickness measurement of large thin-walled parts is proposed. First, a multi-function integrated ultrasonic thickness on-machine measuring device is innovatively designed, which enables the posture of an ultrasonic sensor to adapt to the measured surface orientation automatically. Second, the on-machine measurement model of the thickness distribution is established, which includes a measuring point coordinate extraction model and a precise thickness assessing model. Then, a scanning motion control strategy for contact ultrasonic measurement is proposed to maintain a constant pressure between the ultrasonic transducer and the workpiece during the scanning process. Finally, taking the arched part, inclined plate, and S-shaped thin-walled part as typical objects, the experimental study has been conducted using the proposed method. The experimental results show that the ultrasonic thickness on-machine measurement accuracy can be controlled within 0.04 mm, which validates the feasibility of the ultrasonic thickness on-machine scanning technique on thickness measurement of complex surface thin-walled parts.

engineering, manufacturing,automation & control systems
Thickness evaluations for thin coatings using laser scanning thermography

Fei Chen,Kai Zhang,Haijun Jiang,Zhonghua Shen,Li Chen

DOI: https://doi.org/10.1016/j.ndteint.2023.102817

IF: 4.683

2023-07-01

NDT & E International

Abstract:In this work, we proposed a scanning laser thermographic approach for evaluating the thickness of thin coatings. It is based on the space-resolved temperature profile along the scanning path which correlates to the time-resolved temperature profile. The accuracy of the profile is determined by the spatial resolution rather than the framerate of the IR camera. Both numerical analysis and experimental results showed that the peak time of the first derivative of the spatial-resolved temperature profile was nearly in linear relationship to the coating thickness. Specimens for the coating thickness of 20–150 μm was measured with a maximum relative error of 4.3%.

materials science, characterization & testing
Multi-Mode Electromagnetic Ultrasonic Lamb Wave Tomography Imaging For Variable-Depth Defects In Metal Plates

Songling Huang,Yu Zhang,Shen Wang,Wei Zhao

DOI: https://doi.org/10.3390/s16050628

IF: 3.9

2016-01-01

Sensors

Abstract:This paper proposes a new cross-hole tomography imaging (CTI) method for variable-depth defects in metal plates based on multi-mode electromagnetic ultrasonic Lamb waves (LWs). The dispersion characteristics determine that different modes of LWs are sensitive to different thicknesses of metal plates. In this work, the sensitivities to thickness variation of A0- and S0-mode LWs are theoretically studied. The principles and procedures for the cooperation of A0- and S0-mode LW CTI are proposed. Moreover, the experimental LW imaging system on an aluminum plate with a variable-depth defect is set up, based on A0- and S0-mode EMAT (electromagnetic acoustic transducer) arrays. For comparison, the traditional single-mode LW CTI method is used in the same experimental platform. The imaging results show that the computed thickness distribution by the proposed multi-mode method more accurately reflects the actual thickness variation of the defect, while neither the S0 nor the A0 single-mode method was able to distinguish thickness variation in the defect region. Moreover, the quantification of the defect's thickness variation is more accurate with the multi-mode method. Therefore, theoretical and practical results prove that the variable-depth defect in metal plates can be successfully quantified and visualized by the proposed multi-mode electromagnetic ultrasonic LW CTI method.

Gastroduodenocolic fistula due to a benign gastric ulcer, case report.

A Novel Laser Ultrasonic Thickness Measurement Method for Metal Plate Based on Spectral Analysis

A Study of Inner Crack Testing with the Laser Phased Array Method.

Laser-induced thermal damage detection in metallic materials via acoustic emission and ensemble empirical mode decomposition

Investigation of pipe thickness monitoring using the shear wave EMAT technology with high lift-off distance

Optimization design of laser-EMAT and its application in high-temperature forgings detection

Study on the Laser-EMAT Integrated System for Simultaneously Measuring the Width and Depth of Metal Plate

Simultaneous Thickness, Velocity, Density, and Attenuation Measurement of a Thin Layer by Time-Resolved Acoustic Microscopy

Efficient Fault Tolerant Algorithms for Internet Distributed Systems

Laser ultrasonic inspection for mechanical properties of materials at high temperature

High Precision Ultrasonic Measurement Method for Thin-Walled Parts

Residual strain measurement based on longitudinal to shear wave velocity ratio with a dual-mode EMAT

Thickness Measurements with EMAT Based on Fuzzy Logic

Research on Identification and Detection of Aluminum Plate Thickness Step Change Based on Electromagnetic Acoustic Resonance

Improving laser-EMAT ultrasonic energy conversion efficiency using surface constraint mechanism

Easy-to-operate thickness measurement method for steel plate using bulk-wave EMAT

An Advanced Magnetoacoustic Compound Inspection Method of High-Order Mode EMAT

An improved steady-state method for measuring the thermal contact resistance and bulk thermal conductivity of thin-walled materials having a sub-millimeter thickness

Ultrasonic on-machine scanning for thickness measurement of thin-walled parts: modeling and experiments

Thickness evaluations for thin coatings using laser scanning thermography

Multi-Mode Electromagnetic Ultrasonic Lamb Wave Tomography Imaging For Variable-Depth Defects In Metal Plates