[DISSOCIATED MEDULLARY INSUFFICIENCIES OF THE ADULT].

H. Piguet

1964-12-11

Abstract:

What problem does this paper attempt to address?

Novel Perfluorooctanesulfonate-Imprinted Polymer Immobilized on Spent Coffee Grounds Biochar for Selective Removal of Perfluoroalkyl Acids in Synthetic Wastewater

Jessica M. Steigerwald,Shawnie Peng,Jessica R. Ray

DOI: https://doi.org/10.1021/acsestengg.2c00336

IF: 7.1

2023-01-30

ACS ES&T Engineering

Abstract:Wastewater is an important source of perfluoroalkyl acids (PFAAs) to environmental waters. PFAAs are poorly removed during conventional wastewater treatment and only moderately removed by non-selective adsorbents [e.g., activated carbon (AC)]. Molecularly imprinted polymers (MIPs) enable selective adsorption of trace organics (e.g., PFAAs) by templating polymerization with a target compound; however, MIP morphology limits use for wastewater treatment. To overcome this obstacle, a perfluorooctanesulfonate (PFOS)-templated MIP was immobilized on spent coffee grounds biocharan eco-friendly AC alternativevia radical initiated polymerization. Vinylbenzyl trimethylammonium chloride (VBTAC) and/or 2-(trifluoromethyl)acrylic acid served as functional monomers for MIP synthesis. First, biochar surfaces were functionalized with −NH MIP attachment points via (i) electrophilic aromatic substitution followed by reduction or (ii) heat-catalyzed addition of melamine. Melamine-modified biochar functionalized with VBTAC-MIP (BC-M@MIP-V) demonstrated high PFOS selectivity (K selectivity of 4.52 for perfluorobutanesulfonic acid and 3.76 for perfluorooctanoic acid) and PFAA adsorption comparable to unmodified biochar in ultrapure water (0.043 and 0.039 mg PFAA/g*g/m2, respectively). Adsorption by BC-M@MIP-V increased by 0.012 mg PFAA/g*g/m2 in synthetic wastewater due to reduced MIP swelling and non-specific binding. Single-cycle regeneration of the BC@MIP composites suggest that long material lifetimes are possible. These novel, selective adsorbents present a potential alternative for effective wastewater PFAA treatment.
Removal of Perfluorinated Carboxylates from Washing Wastewater of Perfluorooctanesulfonyl Fluoride Using Activated Carbons and Resins.

Ziwen Du,Shubo Deng,Youguang Chen,Bin Wang,Jun Huang,Yujue Wang,Gang Yu

DOI: https://doi.org/10.1016/j.jhazmat.2014.12.037

IF: 13.6

2014-01-01

Journal of Hazardous Materials

Abstract:Perfluorooctanesulfonyl fluoride (PFOSF) washing wastewater contains high concentrations of perfluorinated carboxylates (PFCAs) including perfluorohexanoate (PFHxA, 0.10 mmol/L), perfluoroheptanoate (PFHpA, 0.11 mmol/L), and perfluorooctanoate (PFOA, 0.29 mmol/L). For the first time, we investigated the removal of these PFCAs from actual wastewater using the bamboo-derived activated carbon (BAC) and resin IRA67. Adsorption kinetics, effects of adsorbent dose, solution pH, and inorganic ions, as well as regeneration and reuse experiments were studied. The removal percents of three PFCAs by BAC and IRA67 followed the increasing order of PFHxA < PFHpA < PFOA, but the adsorption equilibrium time conformed to the reverse trend. PFCAs removal on IRA67 decreased with increasing pH, but BAC almost kept stable PFCAs removal at pH above 5.0. Among competitive adsorption of three PFCAs, PFOA was preferentially adsorbed on both BAC and IRA67. PFCAs removal from actual wastewater by BAC was higher than that in simulated solution, due to the presence of high concentration of inorganic ions in the wastewater. However, the co-existing organic compounds in wastewater significantly suppressed the adsorption of PFCAs. Both spent BAC and IRA67 were successfully regenerated by ethanol solution or NaCl/methanol mixture, and IRA67 showed the stable removal of PFCAs in five adsorption cycles.
Phase I clinical trial of targeted therapy using 131I-Hepama-1 mAb in patients with hepatocellular carcinoma.

Shaoliang Chen,Bei-lei Li,H. Xie,Li Xu,Guangjun Niu,Kuisheng Fan,Q. Fan

DOI: https://doi.org/10.1089/CBR.2004.19.589

2004-11-15

Cancer Biotherapy and Radiopharmaceuticals

Abstract:OBJECTIVES The aim of this study was to evaluate the response- and treatment-related toxicity for patients with unresectable hepatocellular carcinoma (HCC) treated with 131I-Hepama-1 mAb (DGDK-1). MATERIALS AND METHODS Seeking approval for the use of 131I-hepama-1 mAb, 32 patients with unresectable HCC were divided into 5 groups to take part in the Phase I clinical trial study. Systemic reactions and acute toxicity were evaluated weekly for at least 45 days following treatment with an intravenous injection of 10 mg of antibody radiolabeled with 740-3700 MBq (20-100 mCi), divided into 5 groups. RESULTS No patients demonstrated any evidence of fever, severe side effects, or impairments of important organs, such as the lung, liver, and heart. During, and for 45 days after, the treatment, most of their routine examinations of blood, functions of liver and kidneys, and the thyroid hormone were all normal. Hypothyroidism was not observed during the course of monitoring. None of the 32 patients developed human antimurine antibodies (HAMA) within 15 days of therapy; however, 82% of patients were HAMA-positive by 45 days of therapy. According to the pilot study of prognosis, survival from the start of radioimmunotherapy (RIT) was a median of 4 months, and the 1-year survival rate was 31%. The median survival time of 15 patients without metastases was 10 months, and the 1-year survival rate was 60%. Of alpha-fetoprotein (AFP)-positive patients, 75% of AFP levels decreased by at least 50% or became normal. Of all patients, 84% showed an improved Eastern Cooperative Oncology Group (ECOG) performance status. CONCLUSION This phase I clinical trial demonstrated that it was safe to use 131I-hepama- 1 mAb by peripheral intravenous administration. The recommended dose of DGDK-1 for clinical use is 1480-2960 MBq/10 mg.
Role of the Air-Water Interface in Removing Perfluoroalkyl Acids from Drinking Water by Activated Carbon Treatment.

Pingping Meng,Xiangzhe Jiang,Bin Wang,Jun Huang,Yujue Wang,Gang Yu,Ian T. Cousins,Shubo Deng

DOI: https://doi.org/10.1016/j.jhazmat.2019.121981

IF: 13.6

2019-01-01

Journal of Hazardous Materials

Abstract:Contamination of drinking water by per- and polyfluoroalkyl substances (PFASs) is a worldwide problem. In this study, we for the first time revealed the role of the air-water interface in enhancing the removal of long-chain perfluoroalkyl carboxylic (PFCAs; CnF2n+1COOH, n >= 7) and perfluoroalkane sulfonic (PFSAs; CnF2n+1SO3H, n >= 6) acids, collectively termed as perfluoroalkyl acids (PFAAs), through combined aeration and adsorption on two kinds of activated carbon (AC). Aeration was shown to enhance the removal of long-chain PFAAs through adsorption at the air-water interface and subsequent adsorption of PFAA-enriched air bubbles to the AC. The removal of selected long-chain PFAAs was increased by 50-115 % with the assistance of aeration, depending on the perfluoroalkyl chain length. Aeration is more effective in enhancing long-chain PFAA removal as air-water interface adsorption increases with PFAA chain length due to higher surface activity. After removing adsorbed air bubbles by centrifugation, up to 80 % of the long-chain PFAAs were able to desorb from the sorbent, confirming the contribution of the air-water interface to the adsorption of PFAAs on AC. Aeration during AC treatment of water could enhance the removal of long-chain PFAAs, and improve the performance of AC during water treatment.
Rapid removal of PFOA and PFOS via modified industrial solid waste: Mechanisms and influences of water matrices

Hongyi Wan,Rollie Mills,Kai Qu,James C Hower,M Abdul Mottaleb,Dibakar Bhattacharyya,Zhi Xu

DOI: https://doi.org/10.1016/j.cej.2021.133271

2022-04-01

Abstract:Emerging perfluoroalkyl and polyfluoroalkyl substances contaminate waters at trace concentrations, thus rapid and selective adsorbents are pivotal to mitigate the consequent energy-intensive and time-consuming issues in remediation. In this study, coal combustion residuals-fly ash was modified (FA-SCA) to overcome the universal trade-off between high adsorption capacity and fast kinetics. FA-SCA presented rapid adsorption (teq = 2 min) of PFOX (perfluorooctanoic acid and perfluorooctanesulfonic acid, collectively), where the dynamic adsorption capacity (qdyn = qm/teq) was 2-3 orders of magnitude higher than that of benchmark activated carbons and anion-exchange resins. Investigated by advanced characterization and kinetic models, the fast kinetics and superior qdyn are attributed to (1) elevated external diffusion driven by the submicron particle size; (2) enhanced intraparticle diffusion caused by the developed mesoporous structure (Vmeso/Vmicro = 8.1); (3) numerous quaternary ammonium anion-exchange sites (840 μmol/g), and (4) appropriate adsorption affinity (0.031 L/μmol for PFOS, and 0.023 L/μmol for PFOA). Since the adsorption was proven to be a synergistic process of electrostatic and hydrophobic interactions, effective adsorption ([PFOX]ini = 1.21 μM, concentration levels of highly-contaminant-sites) was obtained at conventional natural water chemistries. High selectivity (>85.4% removal) was also achieved with organic/inorganic competitors, especially compounds with partly similar molecular structures to PFOX. In addition, >90% PFOX was removed consistently during five cycles in mild regeneration conditions (pH 12 and 50 °C). Overall, FA-SCA showed no leaching issues of toxic metals and exhibits great potential in both single-adsorption processes and treatment train systems.
Sludge-based activated carbon and its application in the removal of perfluoroalkyl substances: A feasible approach towards a circular economy

Badr A Mohamed,Loretta Y Li,Hanna Hamid,Matthew Jeronimo

DOI: https://doi.org/10.1016/j.chemosphere.2022.133707

IF: 8.8

Chemosphere

Abstract:This study explores the recovery of resources and energy from sewage sludge through the production of sludge-based activated carbon (SBAC) considering circular economy principles. The SBAC production costs were estimated under three scenarios considering various sludge dewatering/drying schemes to determine the production feasibility and its role in the circular economy. SBAC was tested in the removal of a mixture of nine commonly detected poly- and perfluoroalkyl substances (PFASs) in environmentally relevant concentrations of ∽50 μg/L in comparison to commercially available activated carbon (AC) using 5 mg of sorbent and 5 mL of a nine-PFAS mixture in deionised water. SBAC can be produced at approximately 1.2 US $/kg, which is substantially lower than the average production cost of commercial AC of >3 US $/kg. A net revenue ranging from 2 to 7 US $/kg SBAC was estimated by recycling the produced non-condensable gases and bio-oil to produce energy and selling the SBAC. Batch adsorption tests showed that the PFASs removal of SBAC was superior to that of granular AC and similar to that of powdered AC, reaching >91% to below the detection limit. The kinetics tests revealed that adsorption by SBAC and AC occurred within 15 min. The overall results demonstrate the potential of SBAC as an effective sorbent for PFASs, achieving waste-to-resources circular economy via resource and energy recovery from sewage sludge, eliminating sludge disposal and contaminant-leaching to the environment, and in enhancing the quality of wastewater effluent before discharge.
Fluoro-functionalized plant biomass adsorbent: Preparation and application in extraction of trace perfluorinated compounds from environmental water samples

Xi Tan,Yan Shi,Chun-Feng Ma,Quan Chi,Yu-Hang Yang,Wen-Xiang Zhang,Hua-Ming Xiao,Xian Wang

DOI: https://doi.org/10.1016/j.jes.2023.03.023

IF: 6.9

2024-03-01

Journal of Environmental Sciences

Abstract:Perfluorinated compounds (PFCs) are toxic and widely present in the environment, and therefore effective adsorbents are required to remove PFCs from environmental water. In the present study, a new type of fluorinated biomass materials was synthesized via an ingenious fluorosilanization reaction. These adsorbents were applied for the adsorption of 13 typical PFCs, including perfluorocarboxylic acids (PFCAs) and perfluorosulfonic acids (PFSAs). By comparing their adsorption performance, Fluorinated cedar slag (FCS) was discovered to have the best absorption efficiency and enabled highly efficient enrichment of PFCs. The adsorption recovery of FCS with the investigated PFCs is greater than 90% under the optimal adsorption condition. Ascribed to the high affinity of F-F sorbent-sorbate interaction, FCS had good adsorption capacities of PFCs from aqueous solution, with the maximum adsorption capacity of 15.80 mg/g for PFOS and 10.71 mg/g for PFOA, respectively. Moreover, the adsorption time could be achieved in a short time (8 min). Using the FCS absorbent, an innovative FCS-solid phase extraction assisted with high performance liquid chromatography-electrospray-tandem mass spectrometry (FCS-SPE-HPLC-ESI-MS/MS) method was first developed to sensitively detect PFCs in the environmental water samples. The intra-day and inter-day recovery rates of the 13 compounds ranged from 90.7%-104.3%, with the RSD of 2.1%-4.7% (intra-day) and 2.5%-8.5% (inter-day), respectively. This research demonstrates the potential of the newly fluoro-functionalized plant biomass to adsorb PFCs from environmental water, with the advantages of high adsorption efficiencies, high anti-interference, easy operation and low economic cost.

environmental sciences
Removal of Per- and Polyfluoroalkyl Substances by Adsorption on Innovative Adsorbent Materials

Maria Cristina Collivignarelli,Stefano Bellazzi,Francesca Maria Caccamo,Silvia Calatroni,Chiara Milanese,Marco Baldi,Alessandro Abbà,Sabrina Sorlini,Giorgio Bertanza,Alessandro AbbÃ

DOI: https://doi.org/10.3390/su151713056

IF: 3.9

2023-08-30

Sustainability

Abstract:Per- and polyfluoroalkyl substances (PFAS) constitute a group of organofluorine chemical synthetic compounds widely used in industries and manufacturing due to their hydrophobic properties. However, PFAS have been found to cause negative human health outcomes. Therefore, a strong interest in the possible removal of these compounds from wastewater (WW) has been shown. This work aims to present a systematic analysis of the scientific literature related to the innovative and alternative adsorbent materials that can be used for treating PFAS-contaminated WW. Moreover, the adsorption processes are considered, focusing the attention on virgin adsorbent materials and biochar as adsorbents. Virgin adsorbent materials comprise conventional adsorbent materials, functional clays, metal–organic frameworks, and functionalized organic polymers. Biochar includes materials obtained from agricultural or food residues and from sewage sludge. The review shows that conventional treatment units using virgin adsorbent materials are characterized by high adsorption capacity, but also high costs. In addition, the refunctionalization of adsorbent materials is difficult to obtain. On the contrary, biochar, which is a residual product of other production processes, appears to be a cost-effective solution.

environmental sciences,environmental studies,green & sustainable science & technology
Treatment of aqueous per- and poly-fluoroalkyl substances: A review of biochar adsorbent preparation methods

Ali Behnami,Mojtaba Pourakbar,Anand Sharadha-Ravi Ayyar,Ji-Woong Lee,Graham Gagnon,Khaled Zoroufchi Benis

DOI: https://doi.org/10.1016/j.chemosphere.2024.142088

IF: 8.8

2024-04-26

Chemosphere

Abstract:Per- and poly-fluoroalkyl substances (PFAS) are synthetic chemicals widely used in everyday products, causing elevated concentrations in drinking water and posing a global challenge. While adsorption methods are commonly employed for PFAS removal, the substantial cost and environmental footprint of commercial adsorbents highlight the need for more cost-effective alternatives. Additionally, existing adsorbents exhibit limited effectiveness, particularly against diverse PFAS types, such as short-chain PFAS, necessitating modifications to enhance adsorption capacity. Biochar can be considered a cost-effective and eco-friendly alternative to conventional adsorbents. With abundant feedstocks and favorable physicochemical properties, biochar shows significant potential to be applied as an adsorbent for removing contaminants from water. Despite its effectiveness in adsorbing different inorganic and organic contaminants from water environments, some factors restrict its effective application for PFAS adsorption. These factors are related to the biochar properties, and characteristics of PFAS, as well as water chemistry. Therefore, some modifications have been introduced to overcome these limitations and improve biochar's adsorption capacity. This review explores the preparation conditions, including the pyrolysis process, activation, and modification techniques applied to biochar to enhance its adsorption capacity for different types of PFAS. It addresses critical questions about the adsorption performance of biochar and its composites, mechanisms governing PFAS adsorption, challenges, and future perspectives in this field. The surge in research on biochar for PFAS adsorption indicates a growing interest, making this timely review a valuable resource for future research and an in-depth exploration of biochar's potential in PFAS remediation.

environmental sciences
Enhanced Removal of Polyfluoroalkyl Substances by Simple Modified Biochar: Adsorption Performance and Theoretical Calculation

Yinjie Zhang,Xiao Tan,Rui Lu,Yiming Tang,Hantong Qie,Ziyi Huang,Jiashun Zhao,Jun Cui,Wenjie Yang,Aijun Lin

DOI: https://doi.org/10.1021/acsestwater.2c00597

2023-02-13

ACS ES&T Water

Abstract:To cope with the widespread polyfluoroalkyl substance (PFAS) pollution in the global aquatic environment, this study prepared an acid-modified biochar adsorbent derived from sludge with satisfactory performance. The theoretical maximum adsorption capacities of the adsorbent for perfluorooctane sulfonic acid (PFOS) and perfluorooctanoic acid (PFOA) were determined to be 72.17 and 45.88 mg·g–1, respectively. The theoretical calculation of the adsorption of biochar surface functional groups with PFOS and PFOA was first performed in this study, and the mechanism of the adsorption process was inferred with a combination of experimental results and redundancy analysis. The adsorption mechanism is composed mainly of the following three aspects: (I) electrostatic interaction between the positively charged biochar and the deprotonated PFAS; (II) hydrogen bonding between anionic species of PFAS and functional groups; and (III) hydrophobic interaction between long-chain hydrophobic PFAS and biochar. Electrostatic interaction plays a major role in the three main adsorption mechanisms under acidic media. Meanwhile, different functional groups have different adsorption energies for PFAS, and CO has the highest adsorption energy. The findings in this work could provide great insights into the adsorption of PFAS on modified biochar as an environmentally friendly adsorbent to promote resource reuse, improve water quality, and ensure human health.
PFAS removal from water by adsorption with alginate-encapsulated plant albumin and rice straw-derived biochar

Iarin Medeiros Militao,Felicity Roddick,Linhua Fan,Lolita Cueva Zepeda,Rajarathinam Parthasarathy,Rosângela Bergamasco

DOI: https://doi.org/10.1016/j.jwpe.2023.103616

IF: 7

2023-07-01

Journal of Water Process Engineering

Abstract:Adsorption using conventional activated carbon is considered an effective and practical method for per- and polyfluoroalkyl substances (PFAS) removal from contaminated water. However, this application can be limited by long equilibrium times, poor performance in adsorbing short-chain PFAS, and compromised adsorption in the presence of other organic compounds. In this work, rice straw-derived biochar and albumin extracted from Moringa oleifera seeds were compared after encapsulation into alginate beads which were then investigated for removing two PFAS compounds, PFOS (long-chain) and PFBS (short-chain), from aqueous solutions. The effect of albumin and biochar concentrations and the influence of different pre-treatment conditions of biochar production on PFAS removal efficiency were investigated. The batch test results showed a high removal efficiency for PFOS with 1.5 g L−1 of either albumin-alginate beads (up to 87 %) or biochar-alginate composite beads (up to 99 %) for <16 h. While PFBS removal by albumin-alginate composite beads was low (10 %), the diammonium phosphate treated biochar–alginate beads achieved nearly 40 % in <48 h, outperforming some previously reported natural material-based adsorbents that were tested under similar experimental conditions. Adsorption with biochar-alginate beads appeared not to be pH dependent, and the presence of NOM (natural organic matter) did not greatly reduce the removal of either PFOS or PFBS. Hydrophobic sorption was shown to dominate over the electrostatic interaction in the PFAS adsorption. Overall, the potential of the rice straw-derived biochar-alginate beads for the remediation of PFAS in aqueous systems was demonstrated.

engineering, chemical, environmental,water resources
Systematic Investigation of Pfos Adsorption from Water by Metal Organic Frameworks, Activated Carbon, Metal Organic Framework@Activated Carbon, and Functionalized Metal Organic Frameworks

Jasneet Pala,Tin Le,Medha Kasula,Milad Rabbani Esfahani

DOI: https://doi.org/10.2139/ssrn.4273739

2022-01-01

SSRN Electronic Journal

Abstract:The presence of Per- and Polyfluoroalkyl Substances (PFAS) in water causes health effects on humans and animals over time. Among all techniques, the adsorption methodology has shown effective performance for removing PFAS from water. Different adsorbents, including classical powder activated carbon (AC) and metal organic frameworks (MOFs) as new generation of adsorbents have been used for the removal of short-chain (C<6) and long-chain (C>7) PFAS. However, due to the complexity of the adsorption process, the diversity of adsorbents and PFAS compounds, and the lack of standard experimental protocol, the effectiveness and undergoing sorption mechanisms for each of these adsorbents have not been investigated and compared systematically yet. In this work, we synthesized and characterized the adsorbents and then performed a systematic isotherm adsorption protocol to study the adsorption mechanisms and performance of adsorbents, including nanosized activated carbon AC, MIL-101 (Cr), MIL-101 (Cr)-NH2 and novel hybrid adsorbents of MIL-101 (Cr)@AC for the removal of perfluorooctane sulphonic acid (PFOS) from water. Based on the comparative analysis to investigate the effective parameters governing the PFOS adsorption with respect to each adsorbent, AC with around 93% PFOS removal showed supreme performance over other MOFs; however, MOF-based adsorbents showed faster adsorption compared to AC. The MIL-101(Cr)@AC (with 80% removal performance and 2h adsorption time) possessed the advantages of both AC and MIL-101 (Cr). The hydrophobic-hydrophobic and electrostatic interactions were the main dominant adsorption interactions for AC and MOFs, respectively, while both interactions were influential in the MIL-101 (Cr)@AC adsorption.
Sorption of Poly- and Perfluoroalkyl Substances (pfass) Relevant to Aqueous Film-Forming Foam (Afff)-Impacted Groundwater by Biochars and Activated Carbon

Xin Xiao,Bridget A. Ulrich,Baoliang Chen,Christopher P. Higgins

DOI: https://doi.org/10.1021/acs.est.7b00970

IF: 11.4

2017-01-01

Environmental Science & Technology

Abstract:Despite growing concerns about human exposure to perfluorooctanoate (PFOA) and perfluorooctanesulfonate (PFOS), other poly- and perfluoroalkyl substances (PFASs) derived from aqueous film-forming foams (AFFFs) have garnered little attention. While these other PFASs may also be present in AFFF-impacted drinking water, their removal by conventional drinking-water treatment is poorly understood. This study compared the removal of 30 PFASs, including 13 recently discovered PFASs, from an AFFF-impacted drinking water using carbonaceous sorbents (i.e., granular activated carbon, GAC). The approach combined laboratory batch experiments and modeling: batch sorption data were used to determine partition coefficients (Kd) and calibrate a transport model based on intraparticle diffusion-limited sorption kinetics, which was used to make forward predictions of PFAS breakthrough during GAC adsorption. While strong retention was predicted for PFOS and PFOA, nearly all of the recently discovered polyfluorinated chemicals and PFOS-like PFASs detected in the AFFF-impacted drinking water were predicted to break through GAC systems before both PFOS and PFOA. These model breakthrough results were used to evaluate a simplified approach to predicting PFAS removal by GAC using compound-specific retention times on a C18 column (RTC18). Overall, this study reveals that GAC systems for the treatment of AFFF-impacted sources of water for PFOA and PFOS likely achieve poor removal, when operated only for the treatment of PFOS and PFOA, of many unmonitored PFASs of unknown toxicity.
Efficient Separation of Per- and Polyfluoroalkyl Substances (PFAS) from Water by Aminated Polyacrylamide Hydrogel Foam

Yichen Xu,Xueru Yu,Xinhao Wang,Yiqian Song,Wenran Wang,Ming Zhang,Deyang Kong,Zhanghao Chen,Cheng Gu

DOI: https://doi.org/10.1016/j.cej.2024.157833

IF: 15.1

2024-01-01

Chemical Engineering Journal

Abstract:Emerging per- and polyfluoroalkyl substances (PFAS) are highly toxic chemicals with extraodinary stability in the aquatic environment. Highly efficient adsorbents are in urgent need to address the environmental challenges caused by PFAS. Herein, we developed a novel aminated foam adsorbent with high affinity for PFAS adsorption through polymerization, amination and pyrolyzation. For initial 1 μg/L perfluorooctanoic acid (PFOA) solution, more than 97.9 % removal efficiency could be obatined with a rapid equilibration time of ∼ 15 min. The elevated adsorption efficiency could be explained by the synergetic effect of electrostatic/hydrogen bonding and hydrophobic interaction, while the increase of specific surface area (SSA) also has a positive effect on PFOA adsorption. Furthermore, the sythesized polyacrylamide-polyaniline material (pyrolyzed at 301℃, PAM-PANI-2) exhibited high adaptability to different environmental influencing factors, including pH and co-existed organic matters, and presented excellent adsorption removal ability for other common PFAS except for PFOA. Moreover, it is worth noting that this foam material has advantages in regeneration compared to traditional powder adsorbents, without complicated procedures such as centrifugation and filtration. These results indicate that aminated PAM polymers are promising adsorbents in remediations of trace PFAS-contaminated water, which can give new insights to the design and application of novel polymer materials of PFAS treatments.
Adsorbent Materials Used for the Treatment of Per‐ and Poly‐fluoroalkyl Substances (PFAS): A Short Review

Chaimaa Gomri,Belkacem Tarek Benkhaled,Marc Cretin,Mona Semsarilar

DOI: https://doi.org/10.1002/macp.202400012

IF: 2.996

2024-02-26

Macromolecular Chemistry and Physics

Abstract:PFAS, or per‐ and polyfluoroalkyl substances, have received considerable attention due to their persistence in the environment and potential health risks. To address this problem, adsorption has emerged as an effective method for removing PFAS compounds from water. This review provides a comprehensive analysis of various adsorbents used for PFAS removal, including activated carbon, ion exchange resins, clay, and emerging materials such as covalent and metal‐organic framework adsorbents. The effectiveness of these adsorbents in removing PFAS compounds is discussed, along with the factors influencing their adsorption, such as pH, competitive matters, and temperature. This article is protected by copyright. All rights reserved

polymer science
Interaction of beta-lactoglobulin with phospholipid bilayers: a molecular level elucidation as revealed by infrared spectroscopy.

T. Lefèvre,M. Subirade

DOI: https://doi.org/10.1016/S0141-8130(00)00149-5

IF: 8.2

2000-10-10

International Journal of Biological Macromolecules

Abstract:
Adsorption Technology for PFAS Removal in Water: Comparison between Novel Carbonaceous Materials

Marco Petrangeli Papini,Marta Senofonte,Riccardo Antonino Cuzzola,Rania Remmani,Ida Pettiti,Carmela Riccardi,Giulia Simonetti

DOI: https://doi.org/10.3390/ma17174169

IF: 3.4

2024-08-25

Materials

Abstract:PFASs are a variety of ecologically persistent compounds of anthropogenic origin loosely included in many industrial products. In these, the carbon chain can be fully (perfluoroalkyl substances) or partially (polyfluoroalkyl substances) fluorinated. Their ubiquitous presence in many environmental compartments over the years and their long-lasting nature have given rise to concerns about the possible adverse effects of PFASs on ecosystems and human health. Among a number of remediation technologies, adsorption has been demonstrated to be a manageable and cost-effective method for the removal of PFASs in aqueous media. This study tested two novel and eco-friendly adsorbents (pinewood and date seeds biochar) on six different PFASs (PFOS, GenX, PFHxA, PFOA, PFDA, and PFTeDA). Batch sorption tests (24 h) were carried out to evaluate the removal efficiency of each PFAS substance in relation to the two biochars. All samples of liquid phase were analyzed by a developed and then a well-established method: (i) pre-treatment (centrifugation and filtration) and (ii) determination by high-performance liquid chromatography coupled with mass spectrometry (HPLC-MS/MS). The results evidenced a comparable adsorption capacity in both materials but greater in the long-chain PFASs. Such findings may lead to a promising path towards the use of waste-origin materials in the PFAS remediation field.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Assessment of activated carbon as a sorbent amendment for immobilizing perfluoroalkyl acids for surface sediment remediation

Liang Yu,Zulin Hua,Xiaodong Liu,Hongqin Xue

DOI: https://doi.org/10.1016/j.cej.2024.152693

IF: 15.1

2024-06-02

Chemical Engineering Journal

Abstract:The detection of elevated levels of perfluoroalkyl acids (PFAAs) in sediments has become a significant concern, urgently requiring management and remediation efforts. In this study, we investigated the effectiveness of industrially cost-effective activated carbon (AC) in remediating PFAA-contaminated sediments at different disturbance intensities and explored the sorption capacity of AC under broad environmentally relevant conditions and in response to environmental variations. AC exhibited high sorption effectiveness for PFAAs (excluding perfluorobutanoic acid < 40 %) across different pH, ionic strengths (IS), and dissolved organic matter (DOM). However, the increase in pH or reduction in IS might reactivate partially immobilized PFAAs. DOM outcompeted longer-chain PFAAs for sorption sites, resulting in their reactivation on AC, while it showed a stronger sorption than a competitive effect on shorter-chain PFAAs. The 192-day remediation experiment showed that AC significantly deactivated mobile PFAAs and decreased PFAA release by 45.5 %–99.2 % and 61.0 %–98.8 % under weak and intense disturbances, respectively, when compared with untreated sediment. Although intense disturbance led to an increase in PFAA release, the PFAA levels in the water column of the AC group after intense disturbance were comparable or even lower than those before intense disturbance, primarily owing to the secondary sorption of suspended AC. These findings are crucial for the appropriate and safe use of AC for PFAA sequestration, the management of PFAA-contaminated sediments, and the development of effective sediment remediation strategies.

engineering, chemical, environmental
Insights into the Adsorption of Perfluoroalkyl Substances (pfass) on Excess Sludge from an On-Site Leachate Treatment Plant

Lingyue Zhang,Chu Tang,Dongbei Yue

DOI: https://doi.org/10.1016/j.seppur.2023.125639

IF: 8.6

2024-01-01

Separation and Purification Technology

Abstract:The disposal and reduction of excess sludge is one of the most challenging aspects of wastewater treatment. Recycling excess sludge as functional materials is an innovative approach that has garnered broad attention, as it can address environmental concerns and reduce the consumption of valuable materials. However, this approach is still challenging due to the low mixed liquor suspended solids in sewage treatment plants and the high synthesis costs involved. In this study, we proposed the application of excess sludge from an on-site leachate treatment plant for the efficient removal of perfluoroalkyl substances (PFASs) from wastewater. A simple thermal treatment was conducted and the obtained sludge-based adsorbents enable effective PFASs removal. Through the use of low field nuclear magnetic resonance and structural characterizations, results demonstrated that denitrifying sludge had higher hydrophobicity and specific surface area (30.85 m2/g) than nitrifying sludge, resulting in enhanced PFASs adsorption capacity and initial adsorption rates. Kinetic and isotherm simulations indicated that the adsorption was efficient and controlled by surface and intraparticle diffusion. Characterization and regulation results showed that the adsorption was dominated by hydrophobic and electrostatic interactions. These findings suggest a promising recycling approach of excess sludge while elucidating the dominant mechanisms involved.
Polyethyleneimine functionalized cellulose-rich agroforestry residues for removing perfluorooctanoic acid: adsorption performance and mechanism

DOI: https://doi.org/10.1007/s10570-023-05090-2

IF: 6.123

2023-02-16

Cellulose

Abstract:Emerging pollutants such as perfluorooctanoic acid (PFOA) have received global attention due to their serious threats to human health and the environment. Using polyethyleneimine (PEI) as the modifier, balsa wood (BA), loofah (LF), and pomelo peel (PP) as the raw materials, three bio-sourced adsorbents PEI-BA, PEI-LF, and PEI-PP were prepared and used to remove PFOA from water. The effective grafting of PEI on the surface of agroforestry residues was verified by a combination of scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM–EDS), Fourier transform infrared spectroscopy (FTIR), and elemental analysis. Subsequently, several factors affecting the adsorption efficiency of PEI-BA, PEI-LF, and PEI-PP for PFOA were systematically investigated. By batch experiments, the maximum adsorption capacity at pH 3.0 was determined to be 279.3, 252.1, and 274.3 mg/g within 4 h for PEI-BA, PEI-LF, and PEI-PP, respectively. The adsorption of PFOA was a spontaneous and exothermic process and, the kinetics and isotherms followed the pseudo-second-order model and the Freundlich model, respectively. During the adsorption process, the electrostatic and hydrophobic interactions were verified between the adsorbents and PFOA. The presence of cations (Na + , Mg 2+ , Fe 3+ , 0.1–10 mM) could promote the adsorption of PFOA as a result of salting-out and bridge effects, whereas anions (NO 3 − , SO 4 2− , and PO 4 3− , 10 mM) would inhibit the adsorption due to ion competition for available adsorption sites. Finally, three bio-adsorbents could be easily regenerated by an equal volume of ethanol and water, demonstrating their potential for highly efficient removal of PFOA in water.

materials science, textiles,polymer science, paper & wood

[DISSOCIATED MEDULLARY INSUFFICIENCIES OF THE ADULT].

Novel Perfluorooctanesulfonate-Imprinted Polymer Immobilized on Spent Coffee Grounds Biochar for Selective Removal of Perfluoroalkyl Acids in Synthetic Wastewater

Removal of Perfluorinated Carboxylates from Washing Wastewater of Perfluorooctanesulfonyl Fluoride Using Activated Carbons and Resins.

Phase I clinical trial of targeted therapy using 131I-Hepama-1 mAb in patients with hepatocellular carcinoma.

Role of the Air-Water Interface in Removing Perfluoroalkyl Acids from Drinking Water by Activated Carbon Treatment.

Rapid removal of PFOA and PFOS via modified industrial solid waste: Mechanisms and influences of water matrices

Sludge-based activated carbon and its application in the removal of perfluoroalkyl substances: A feasible approach towards a circular economy

Fluoro-functionalized plant biomass adsorbent: Preparation and application in extraction of trace perfluorinated compounds from environmental water samples

Removal of Per- and Polyfluoroalkyl Substances by Adsorption on Innovative Adsorbent Materials

Treatment of aqueous per- and poly-fluoroalkyl substances: A review of biochar adsorbent preparation methods

Enhanced Removal of Polyfluoroalkyl Substances by Simple Modified Biochar: Adsorption Performance and Theoretical Calculation

PFAS removal from water by adsorption with alginate-encapsulated plant albumin and rice straw-derived biochar

Systematic Investigation of Pfos Adsorption from Water by Metal Organic Frameworks, Activated Carbon, Metal Organic Framework@Activated Carbon, and Functionalized Metal Organic Frameworks

Sorption of Poly- and Perfluoroalkyl Substances (pfass) Relevant to Aqueous Film-Forming Foam (Afff)-Impacted Groundwater by Biochars and Activated Carbon

Efficient Separation of Per- and Polyfluoroalkyl Substances (PFAS) from Water by Aminated Polyacrylamide Hydrogel Foam

Adsorbent Materials Used for the Treatment of Per‐ and Poly‐fluoroalkyl Substances (PFAS): A Short Review

Interaction of beta-lactoglobulin with phospholipid bilayers: a molecular level elucidation as revealed by infrared spectroscopy.

Adsorption Technology for PFAS Removal in Water: Comparison between Novel Carbonaceous Materials

Assessment of activated carbon as a sorbent amendment for immobilizing perfluoroalkyl acids for surface sediment remediation

Insights into the Adsorption of Perfluoroalkyl Substances (pfass) on Excess Sludge from an On-Site Leachate Treatment Plant

Polyethyleneimine functionalized cellulose-rich agroforestry residues for removing perfluorooctanoic acid: adsorption performance and mechanism