Empirically Based Strategies for Preventing Juvenile Delinquency.

D. Pardini

DOI: https://doi.org/10.1016/j.chc.2015.11.009

IF: 2.41

2016-04-01

Child and Adolescent Psychiatric Clinics of North America

Abstract:

What problem does this paper attempt to address?

Chitin-biocalcium as a novel superior composite for ciprofloxacin removal: Synergism of adsorption and flocculation

Rui Zhao,Yuxuan Wang,Yanyan An,Liuwei Yang,Qiang Sun,Jiangya Ma,Huaili Zheng

DOI: https://doi.org/10.1016/j.jhazmat.2021.126917

IF: 13.6

2022-02-01

Journal of Hazardous Materials

Abstract:The ubiquitous present antibiotics in aquatic environment is attracting increasing concern due to the dual problems of bioaccumulation toxicity and antibiotic resistance. In this study, a low-cost chitin-biocalcium (CC) composite was developed by a facile alkali activation process from shell waste for typical antibiotics ciprofloxacin (CIP) removal. Response surface methodology (RSM) was utilized to optimize synthesis methodology. The optimized CC products featured superior CIP removal capacity of 2432 mg/g at 25 °C (adsorption combined with flocculation), rapid adsorption kinetics, high removal efficiency (95.58%) and wide pH adaptability (under pH range 4.0–10.0). The functional groups in chitin and high content of biocalcium (Ca2+) endowed CC abundant active sites. The kinetic experimental data was fitted well by pseudo-second-order and intraparticle diffusion model at different concentrations, revealing the removal was controlled by chemisorption and mass transport step. From the macroscopic aspect, flocs were produced with the increase of CIP concentration during the reaction, adsorption combined with flocculation were related to the CIP removal. From the microcosmic aspect, the superior removal performance was attributed to cation bridging, cation complexation among biocalcium-CIP and hydrogen bond between functional groups of chitin and CIP.

environmental sciences,engineering, environmental
Carbon dioxide activated biochar-clay mineral composite efficiently removes ciprofloxacin from contaminated water - Reveals an incubation study

Muhammad Arif,Guijian Liu,Muhammad Zia ur Rehman,Balal Yousaf,Rafay Ahmed,Manik Mian,Aniqa Ashraf,Mehr Ahmed Mujtaba Munir,Muhammad Saqib Rashid,Asif Naeem,Md Manik Mian

DOI: https://doi.org/10.1016/j.jclepro.2021.130079

IF: 11.1

2022-01-01

Journal of Cleaner Production

Abstract:Ciprofloxacin, a second-generation synthetic fluoroquinolone derivative widely used in human and veterinary medicines, has the potential to pose a serious risk to aquatic organisms and humans. The current research investigated the removal of ciprofloxacin using biochar treated with clay mineral and subsequently activated with carbon dioxide (CO2) produced at two different pyrolysis temperatures (350 and 650 °C). Batch adsorption experiments were carried out to assess the removal efficiency of ciprofloxacin by as-synthesized materials. The effects of various factors, such as pH, contact time, adsorbent dose, initial ciprofloxacin concentration, and temperature were studied during the removal process. The physicochemical characterization results verified the successful loading of clay minerals on biochar. Non-linear adsorption models were employed to understand the nature of adsorption processes however, the Pseudo-second-order kinetic and Freudlich and Redlich Peterson isotherm models best fitted with the adsorption data. These findings indicated that the adsorption did not follow an ideal monolayer adsorption suggesting hybrid chemical adsorption process that was spontaneous and endothermic. The maximum adsorption (50.32 mg g−1) of ciprofloxacin was achieved by CO2 activated biochar-clay mineral composite prepared at 350 °C, and was almost two times higher than the pristine biochar at neutral pH and 40 °C. The possible proposed mechanisms involved for the removal of ciprofloxacin were electrostatic attraction, cation exchange, pore-filling effect, and π-π interactions. Our findings demonstrate that application of CO2 activated biochar-clay mineral composite is a promising technique for efficient removal of ciprofloxacin from aqueous solution.

environmental sciences,green & sustainable science & technology,engineering, environmental
High-effective, convenient and environmental-friendly MOFs-chitosan-glyoxal composite film for ceftizoxime adsorption: Behavior and mechanisms

Menghan Qin,Detian Dou,Yinghua Zhu,Manman Zhang,Jingjing Deng,Tianshu Zhou

DOI: https://doi.org/10.1016/j.ijbiomac.2024.137077

IF: 8.2

2024-11-06

International Journal of Biological Macromolecules

Abstract:In this work, a novel PCN-222-chitosan-glyoxal (PCN@CSG 2 ) composite film was constructed by loading PCN-222 in chitosan substrate, and used for ceftizoxime adsorption. The results demonstrated that the PCN@CSG not only had excellent adsorption properties for ceftizoxime, but also maintained excellent structural properties in harsh environments (strong acids and alkalis), making it have good recycling performance. Specifically, the adsorption kinetics and isotherms investigation demonstrated that the adsorption process followed the pseudo-second-order kinetic model and Freundlich isotherm model respectively, indicating that it was a multilayer process mainly controlled by chemisorption. The PCN@CSG possesses excellent absorptive capacity of 561.7 mg·g −1 and reaches equilibrium rapidly within 60 min, which is attributed to the structural advantages of PCN-222 and chitosan. The amino, carboxyl and hydroxyl functional groups of PCN-222 provide numbers of active sites and cationic chitin greatly promoted the electrostatic adsorption with negative ceftizoxime. In addition, the PCN@CSG has the advantages of renewable and environment-friendly for the biodegradation of chitosan. After five consecutive adsorption-desorption cycles, the removal rate was still higher than 90 %, confirming the excellent reusability of PCN@CSG. This work provided a great prospect for the design and application of shaped-MOFs composite materials for the removal of cephalosporins in environmental water.

polymer science,biochemistry & molecular biology,chemistry, applied
Adsorption kinetics, isotherms and mechanisms of three‐component covalent organic polymer/sodium alginate beads for ciprofloxacin removal from aqueous solution

Can Shi,Yuyang Bai,Fangyuan Zhang,Junhong Gu,Aiyuan Jia,Zhi Liu,Zhisheng Liu,Mei Hong,Yangxue Li

DOI: https://doi.org/10.1002/pol.20230258

IF: 3.046

2023-06-20

Journal of Polymer Science

Abstract:Ciprofloxacin (CIP), an important representative fluoroquinolone antibiotic, has been frequently detected in water sources, thus threatening aquatic organisms and human health. In this work, a porous three‐component covalent organic polymer (SLEL‐6) was synthesized through multi‐component (MC) reaction systems for adsorptive removal of CIP from aqueous solution, followed by an encapsulation process to achieve SLEL‐6/sodium alginate (SA) beads with boosted adsorption ability, reusability and recyclability. By virtue of the hierarchical porous natures, functional groups as well as π‐rich skeletons, SLEL‐6 and SLEL‐6/SA beads could deal with CIP contamination effectively. Moreover, the adsorption isotherms of CIP by SLEL‐6 and SLEL‐6/SA beads follow the Langmuir model showing high theoretical maximum adsorption capacities of 57.47 and 163.93 mg g−1, respectively. Furthermore, the plausible mechanisms are proposed according to experimental studies of influencing factors, coupled with characterizations before and after adsorption. This work therefore highlighting the immense potential of COP‐based SA composite beads as new‐type globular adsorbents for eliminating fluoroquinolones from aqueous solution.

polymer science
Development of calcium phosphate-chitosan composites with improved removal capacity toward tetracycline antibiotic: Adsorption and electrokinetic properties

Hamid Ait Said,Hamza Elbaza,Mohammed Lahcini,Allal Barroug,Hassan Noukrati,Hicham Ben Youcef

DOI: https://doi.org/10.1016/j.ijbiomac.2023.128610

Abstract:Two eco-friendly and highly efficient adsorbents, namely brushite-chitosan (DCPD-CS), and monetite-chitosan (DCPA-CS) composites were synthesized via a simple and low-cost method and used for tetracycline (TTC) removal. The removal behavior of TTC onto the composite particles was studied considering various parameters, including contact time, pollutant concentration, and pH. The maximum TTC adsorption capacity was 138.56 and 112.48 mg/g for the DCPD-CS and DCPA-CS, respectively. Increasing the pH to 11 significantly enhanced the adsorption capacity to 223.84 mg/g for DCPD-CS and 205.92 mg/g for DCPA-CS. The antibiotic adsorption process was well-fitted by the pseudo-second-order kinetic and Langmuir isotherm models. Electrostatic attractions, complexation, and hydrogen bonding are the main mechanisms governing the TTC removal process. Desorption tests demonstrated that the (NH4)2HPO4 solution was the most effective desorbing agent. The developed composites were more efficient than DCPD and DCPA reference samples and could be used as valuable adsorbents of TTC from contaminated wastewater.
Elimination of Ciprofloxacin from Aqueous Solution by Ultrasonic-Assisted Adsorption Using Chitosan Crosslinked Graphene Oxide Nanoparticles

Uplabdhi Tyagi,Jatin Kuhar,Vinita Khandegar,Sanigdha Acharya,Neeru Anand,Arinjay Jain

DOI: https://doi.org/10.3103/s1063455x24010089

2024-03-05

Journal of Water Chemistry and Technology

Abstract:Aquatic life is largely affected by the toxic nature of pharmaceutical waste that is released into the environment and affects nature at every level. To preserve nature, it is very important to remove pharmaceutical waste, such as ciprofloxacin (CIP) and other antibiotics from nature. In this study, chitosan-graphene-based eco-friendly nano-adsorbent (CS-GO-NPs) was synthesized for the removal of CIP from an aqueous medium using ultrasonic-assisted adsorption. A detailed analysis of process conditions including pH, initial concentration, adsorbent dose, and temperature was performed. Results were found to be significant and more than 94% removal efficiency was achieved using an optimum concentration of 200 mg/L, 5 pH, and adsorption time of 20 min. Further, batch adsorption data was used to study the kinetic and thermodynamic behavior and an isotherm study was performed to determine the adsorbate-adsorbent interaction. Experimental results showed a significant agreement with the theoretical values and more than 0.99 regression coefficient ( R 2 ) values were obtained for pseudo-second-order and Freundlich isotherm. Further, an adsorption mechanism was also proposed for the CIP-(CS-GO-NPs) system, and found that film diffusion dominates the process, while pore diffusion also plays a vital role in devising an effective eco-friendly adsorbent. The proposed study provides an effective and sustainable route for the management of toxic pharmaceutical wastes using chitosan-graphene-based nano-adsorbent under mild process conditions.

chemistry, physical, applied, analytical
[Biochemical effects of genes].

P. Karlson

Abstract:
Preparation of a Three-Dimensional Porous Graphene Oxide–Kaolinite–Poly(vinyl alcohol) Composite for Efficient Adsorption and Removal of Ciprofloxacin

Xiaohui Huang,Jie Tian,Yuewei Li,Xianglu Yin,Wei Wu

DOI: https://doi.org/10.1021/acs.langmuir.0c00654

IF: 3.9

2020-08-26

Langmuir

Abstract:Because of the widespread presence of antibiotics in water, soil, and other environments, they pose great potential risks to the environment, threatening human and animal health. In this study, graphene oxide–kaolinite homogeneous dispersion was prepared by simple liquid phase exfoliation. The three-dimensional (3D) porous graphene oxide–kaolinite–poly(vinyl alcohol) composites were prepared by the cross-linking of poly(vinyl alcohol) and the formation of ice crystals during the freezing-drying process. Three influencing factors [adsorbent dosage, ciprofloxacin (CIP) initial concentration, and time] of CIP adsorption and removal were systematically analyzed by the response surface method. The order of significance for response values (CIP removal rate) was adsorbent dosage > CIP initial concentration > time. The 3D porous material showed good adsorption capacity of CIP, the theoretical maximum adsorption capacity was 408.16 mg/g, and it had good recyclability. By Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy analysis, it was found the composite adsorbs CIP by hydrogen bonding and π–π interaction. In conclusion, the graphene oxide–kaolinite–poly(vinyl alcohol) porous composite is a good candidate for efficient antibiotic wastewater treatment.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.langmuir.0c00654?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.langmuir.0c00654</a>.Adsorption kinetic and isotherm model; GKPR preparation parameters, CIP standard curve, and structural formula; SEM images of directly exfoliated kaolinite and TEM images of GO; RSM parameters; and adsorption kinetic and isotherm model parameters (<a class="ext-link" href="/doi/suppl/10.1021/acs.langmuir.0c00654/suppl_file/la0c00654_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

chemistry, multidisciplinary, physical,materials science
Highly sulfonated hyper-cross-linked polymers as promising adsorbents for efficient and selective removal of ciprofloxacin from water

Joanna Wolska,Marcin Frankowski,Jacek Jenczyk,Lukasz Wolski

DOI: https://doi.org/10.1016/j.seppur.2024.127147

IF: 8.6

2024-09-01

Separation and Purification Technology

Abstract:This study aims at the development of novel and highly sulfonated hyper-cross-linked polymers (sHCPs) using facile and one-step synthetic approach, and verification of the potential applicability of the as-synthesized polymers in the adsorptive removal of various antibiotic pollutants under environmentally relevant conditions. The sHCPs synthesized in this work were capable of highly efficient removal of antibiotic pollutants at relatively high (30 mg/L) and low (50 µg/L) initial concentrations, both from a simple as well as complex water matrices. The rate of ciprofloxacin removal and the adsorption capacity observed for the most efficient adsorbent (qe = 757.7 mg/g) were found to be approximately twice higher than that established for other previously reported sulfonated polymers prepared via post-synthetic sulfonation (qe = 476.9 mg/g), and commercial polymer-based adsorbents (e.g. Amberlyst-15, qe = 438.5 mg/g). The highest adsorption capacity was observed at pH close to neutral for polar antibiotic pollutants that contain protonated functional groups and exist in cationic or zwitterion form (e.g. ciprofloxacin and tetracycline). The reported results clearly imply that highly sulfonated hyper-cross-linked polymers are promising candidates for potential practical application for the elimination of organic pollutants from aqueous media, being capable of selective removal of various antibiotics via ionic interaction even in the presence of a great excess of other cations, anions and organic matter naturally existing in environmentally relevant water samples (e.g. river water).

engineering, chemical
Hybrid process of adsorption and electrochemically based green regeneration of bentonite clay for ofloxacin and ciprofloxacin removal

Raissa Antonelli,Geoffroy Roger Pointer Malpass,Meuris Gurgel Carlos da Silva,Melissa Gurgel Adeodato Vieira

DOI: https://doi.org/10.1007/s11356-023-26175-2

Abstract:Removal of emerging contaminants, such as antibiotics, from wastewater by adsorption is a simple, low-cost, and high-performance process; however, regeneration and reuse of the exhausted adsorbent are necessary to make the process economically viable. This study aimed to investigate the possibility of electrochemical-based regeneration of clay-type materials. For this, the calcined Verde-lodo (CVL) clay was saturated with the antibiotics ofloxacin (OFL) and ciprofloxacin (CIP) in one-component systems by an adsorption process and then subjected to photo-assisted electrochemical oxidation (0.45 A, 0.05 mol/L NaCl, UV-254 nm, and 60 min), which promotes both pollutant degradation and adsorbent regeneration. The external surface of the CVL clay was investigated by X-ray photoelectron spectroscopy before and after the adsorption process. The influence of regeneration time was evaluated for the CVL clay/OFL and CVL clay/CIP systems, and the results demonstrate high regeneration efficiencies after 1 h of photo-assisted electrochemical oxidation. Clay stability during regeneration was investigated by four successive cycles in different aqueous matrices (ultrapure water, synthetic urine, and river water). The results indicated that the CVL clay is relatively stable under the photo-assisted electrochemical regeneration process. Furthermore, CVL clay was able to remove antibiotics even in the presence of natural interfering agents. The hybrid adsorption/oxidation process applied here demonstrated the electrochemical-based regeneration potential of CVL clay for the treatment of emerging contaminants, since it can be operated quickly (1h of treatment) and with lower consumption of energy (3.93 kWh kg-1) than the traditional method of thermal regeneration (10 kWh kg-1).
Retention of Ciprofloxacin and Carbamazepine from Aqueous Solutions Using Chitosan-Based Cryostructured Composites

Marinela-Victoria Dumitru,Ana-Lorena Neagu,Andreea Miron,Maria Inês Roque,Luisa Durães,Ana-Mihaela Gavrilă,Andrei Sarbu,Horia Iovu,Anita-Laura Chiriac,Tanța Verona Iordache

DOI: https://doi.org/10.3390/polym16050639

IF: 5

2024-02-28

Polymers

Abstract:Water pollution is becoming a great concern at the global level due to highly polluted effluents, which are charged year by year with increasing amounts of organic residues, dyes, pharmaceuticals and heavy metals. For some of these pollutants, the industrial treatment of wastewater is still relevant. Yet, in some cases, such as pharmaceuticals, specific treatment schemes are urgently required. Therefore, the present study describes the synthesis and evaluation of promising cryostructured composite adsorbents based on chitosan containing native minerals and two types of reinforcement materials (functionalized kaolin and synthetic silicate microparticles). The targeted pharmaceuticals refer to the ciprofloxacin (CIP) antibiotic and the carbamazepine (CBZ) drug, for which the current water treatment process seem to be less efficient, making them appear in exceedingly high concentrations, even in tap water. The study reveals first the progress made for improving the mechanical stability and resilience to water disintegration, as a function of pH, of chitosan-based cryostructures. Further on, a retention study shows that both pharmaceuticals are retained with high efficiency (up to 85.94% CIP and 86.38% CBZ) from diluted aqueous solutions.

polymer science
Carbon-Supported Nanocomposite Synthesis, Characterization, and Application as an Efficient Adsorbent for Ciprofloxacin and Amoxicillin

Maria Sadia,Izaz Ahmad,Shaukat Aziz,Rizwan Khan,Muhammad Zahoor,Riaz Ullah,Essam A. Ali

DOI: https://doi.org/10.1021/acsomega.3c08161

IF: 4.1

2024-02-20

ACS Omega

Abstract:The existence of antibiotics in the environment has recently raised serious concerns about their possible hazards to human health and the water ecosystem. In the current study, an activated carbon-supported nanocomposite, AC-CoFe(2)O(3), was synthesized by a coprecipitation method, characterized, and then applied to adsorb different drugs from water. The synthesized composites were characterized by using energy-dispersive X-ray spectroscopy, Fourier transform infrared spectroscopy,...

chemistry, multidisciplinary
Simple fabrication of carboxymethyl cellulose and κ-carrageenan composite aerogel with efficient performance in removal of fluoroquinolone antibiotics from water

Na Li,Boqiang Gao,Ran Yang,Hu Yang

DOI: https://doi.org/10.1007/s11783-022-1568-x

2022-04-16

Abstract:3D composite aerogels (CMC-CG) composed of carboxymethyl cellulose and κ-carrageenan were designed and fabricated using the one-pot synthesis technique. The optimized CMC-CG showed a good mechanical property and a high swelling ratio due to its superior textural properties with a proper chemically cross-linked interpenetrating network structure. CMC-CG was utilized for the removal of various fluoroquinolones (FQs) from water and exhibited high adsorption performance because of effective electrostatic attraction and hydrogen bonding interactions. Ciprofloxacin (CIP), a popular FQ, was used as the representative. The optimized CMC-CG had a theoretically maximal CIP uptake of approximately 1.271 mmol/g at the pH of 5.0. The adsorption capacity of CMC-CG was improved in the presence of some cations, Cu2+ and Fe3+ ions, at a low concentration through the bridging effect but was reduced at a high concentration. The investigation of adsorption mechanisms, based on the adsorption kinetics, isotherms and thermodynamic study, Fourier transform infrared spectrometry and X-ray photoelectron spectroscopy analyses before and after adsorption, and changes in the adsorption performance of CMC-CG toward two molecular probes, further indicated that electrostatic attraction was the dominant interaction rather than hydrogen bonding in this adsorption. CMC-CG after saturated adsorption of CIP could be easily regenerated using a dilute NaCl aqueous solution and reused efficiently. Moreover, the disused aerogel could still be reused as a new adsorbent for effective adsorption of Cu2+ ion. Overall, this study suggested the promising applications of this composite aerogel as an eco-friendly, cost-effective, and recyclable adsorbent for the efficient removal of FQs from water.

environmental sciences,engineering, environmental
Removal of ciprofloxacin from water by millimeter-sized sodium alginate/H3PO4 activated corncob-based biochar composite beads

Jian Chen,Jinbo Ouyang,Xionghui Cai,Xiaohong Xing,Limin Zhou,Zhirong Liu,Di Cai

DOI: https://doi.org/10.1016/j.seppur.2021.119371

IF: 8.6

2021-12-01

Separation and Purification Technology

Abstract:The removal of ciprofloxacin (CIP) from aqueous system is of great significance for water treatment. Here, millimeter-sized sodium alginate/H3PO4 activated corncob-based biochar composite beads (SA-PB) were prepared by a facile phase inversion method. These beads were characterized with SEM, EDS, FTIR, XRD and Raman. Results showed that SA-PB beads were successfully prepared and endowed the merits from alginate and biochar. SA-PB containing 80 wt% PB (SA-PB80) exhibited excellent CIP sorption capacity, which is much higher than pure SA and those containing 20 wt% and 50 wt% PB. Kinetic results showed that the sorption process could be fitted to pseudo-second-order model. The isotherm data indicated that sorption behavior conformed to the Langmuir model. Furthermore, SA-PB exhibited high tolerance to ionic strength and favorable reusability, and SA-PB also has plentiful desirable advantages such as biodegradability, economy and easily separable for solid-liquid system as well as its efficient CIP capture performance.

engineering, chemical
Potential of chitosan and activated carbon biocomposites for removing enrofloxacin and oxytetracycline from water

José Manuel Molina-Amaya,José Antonio Ávila-Reyes,Eli Amanda Delgado-Alvarado,Laura Silvia González-Valdez,Rene Torres-Ricario,Marlon Rojas-López,Norma Almaraz-Abarca,Marcela Verónica Gutiérrez-Velázquez

DOI: https://doi.org/10.20937/rica.55051

2024-06-13

Revista Internacional de Contaminación Ambiental

Abstract:Enrofloxacin (ENRO) and oxytetracycline (OTC) are two antibiotics, which are difficult to remove by conventional water treatment methods. The characteristics of the biocomposites suggest that they could represent an alternative for the removal of this type of substances through adsorption processes. The current study aimed to determine and compare the potential of biocomposites formed with chitosan and different concentrations of activated carbon (AC) with a particle size of 500 nm, prepared from agave bagasse, to remove enrofloxacin and oxytetracycline solved in water. The effectiveness of the addition of different concentrations of AC (0, 0.5, 2 and 5% w/v) to chitosan was evaluated by morphological analysis using scanning electron microscopy (SEM). The detection of the characteristic functional groups carried out by Fourier transform infrared spectroscopy (FTIR) indicated that the nanoparticles of AC were attached in the chitosan biocomposite, and stable chemical crosslinking was formed during the polymerization process. The removal test of ENRO (10 mg/mL) and OTC (10 mg/mL) in a water was performed by a gradient method of high-performance liquid chromatography (HPLC). The results showed that the addition of AC to chitosan formed a biocomposite with maximum capacity to remove 59.3% of OTC (contact time 2 h at 100 rpm, 4 g biocomposite/L solution, pH 6-7, 30 oC), and a maximum removal of 50.3% of ENRO (contact time 2 h at 100 rpm, 4 g biocomposite/L solution, pH 6, 30 oC). Biocomposites formed by chitosan and agave activated carbon can support the development of tools for the removal of recalcitrant antibiotics from water bodies.

environmental sciences
High-performance functional cellulose foam fabricated with theoretically optimized imidazolium salts for the efficient removal of ciprofloxacin

Wenqi Song,Liwei Qian,Zongcheng Miao,Valentin Nica,Yuzhen Zhao,Zemin He,Yanfang Zhu,Jianjing Gao,Xiaorui Li

DOI: https://doi.org/10.1016/j.carbpol.2023.121001

2023-09-01

Abstract:With the increasing requirements for sustainable development and environmental protection, the design and development of bio-adsorbent based on the widely sourced cellulose have attracted widespread attention. In this study, a polymeric imidazolium satls (PIMS) functionalized cellulose foam (CF@PIMS) was conveniently fabricated. It was then employed to efficiently remove ciprofloxacin (CIP). Three imidazolium salts containing phenyl groups that can lead to multiple interactions with CIP were elaborately designed and then screened through a combination of molecular simulation and removal experiments to acquire the most significant binding ability of CF@PIMS. Besides, the CF@PIMS retained the well-defined 3D network structure as well as high porosity (90.3 %) and total intrusion volume (6.05 mL g-1) as the original cellulose foam (CF). Therefore, the adsorption capacity of CF@PIMS reached an astonishing value of 736.9 mg g-1, nearly 10 times that of the CF. Furthermore, the pH-affected and ionic strength-affected adsorption experiments confirmed that the non-electrostatic interaction took on a critical significance in the adsorption. The reusability experiments showed that the recovery efficiency of CF@PIMS was higher than 75 % after 10 adsorption cycles. Thus, a high-potential method was proposed in terms of the design and preparation of functionalized bio-adsorbent to remove waste matters from samples of the environment.
In-situ synthesis of MIL-100(Fe)@chitosan composite beads with hierarchical porous structure for efficient adsorption of chlortetracycline hydrochloride: Synthesis, performance and mechanisms

Si Duan,Yuan Gao,Guihong Lan,Haiyan Qiu,Bo Xu,Zhuang Xie,Songsong Xue,Tianxiong Ou

DOI: https://doi.org/10.1016/j.seppur.2023.125938

IF: 8.6

2023-12-08

Separation and Purification Technology

Abstract:The widespread use of chlortetracycline hydrochloride (CTC) inevitably poses a potential threat to human health and the biological system, and its environmental pollution and ecotoxicological effects cannot be ignored. Herein, we adopted an in-situ growth method to immobilize the powder form of MIL-100(Fe) adsorbent into low-cost chitosan (CS) matrix for the CTC removal. Metal hydroxide (or metal oxide)/CS beads from the acid-dissolved/alkali-solidified self-sphering shaping method were employed as the substrates for MIL-100(Fe) immobilization, allowing it grow uniformly and stably. Notably, this strategy not only reduced the loss in the separation and regeneration process of powdery MIL-100(Fe), but also improved the adsorption capacity of the CS. Isotherm and kinetic studies showed that the Freundlich and PSO models can describe the experimental data better, respectively, and the maximum adsorption capacity of Langmuir can reach 578.03 mg g −1 . Further, the performance of MIL-100@CS-2 composite beads was thoroughly explored by batch experiments and response surface methodology (RSM) to obtain the optimized operating conditions with the highest CTC removal rate. By combining the density functional theory (DFT) calculation with experimental analysis, the adsorption mechanisms of pore filling, hydrogen bonding , electrostatic interaction, π-π EDA interaction, and hydrophilic interaction were proposed. This work provides a reliable basis for the development of shaping adsorbents and has potential application prospects in the treatment of wastewater containing antibiotics.

engineering, chemical
Synthesis of Eco-Friendly Biopolymer, Alginate-Chitosan Composite to Adsorb the Heavy Metals, Cd(II) and Pb(II) from Contaminated Effluents

Mohammed F. Hamza,Nora A. Hamad,Doaa M. Hamad,Mahmoud S. Khalafalla,Adel A.-H. Abdel-Rahman,Ibrahim F. Zeid,Yuezhou Wei,Mahmoud M. Hessien,Amr Fouda,Waheed M. Salem

DOI: https://doi.org/10.3390/ma14092189

IF: 3.4

2021-04-24

Materials

Abstract:Efficient removal of Cd(II) and Pb(II) from contaminated water is considered a fundamental point of view. Synthetic hydrogel biopolymers based on chitosan and alginate (cost-effective and eco-friendly) were successfully designed and characterized by highly efficient removal contaminants. The sorbents are characterized by FTIR, SEM-EDX, TGA, XPS analyses and textural properties which are qualified by N2 adsorption. The sorption properties are firstly investigated by the effect of pH, sorption isotherms, uptake kinetics, and selectivity from multi-metal solution with equi-molar concentration. The sorbent with 1:3 ratios (of chitosan and alginate respectively) is the most effective for metal removal (i.e., 0.81 mmol Cd g−1 and 0.41 mmol Pb g−1). Langmuir and Sip’s models fitted better the adsorption isotherms compared to the Freundlich model. Uptake kinetics was well fitted by pseudo-first-order rate equation, while the saturation was achieved within 40 min. The sorbent shows good reproducibility through duplicate the experiments with negligible decreasing efficiency (>2.5%). The sorbent was applied for water treatment on samples collected from the industrial area (i.e., 653 and 203 times over the MCL for Cd(II) and Pb(II) respectively according to WHO). The concentration of Cd and Pb was drastically decreased in the effluents as pH increased with removal efficiency up to 99% for both elements at pH 5.8 and SD equivalent 1 g L−1 for 5 h.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Chitin/calcite composite extracted from shell waste as a low-cost adsorbent for removal of tetracycline and ciprofloxacin: Effects and mechanisms

Erming Ouyang,Mingming Wu,Wanyuan He,Haiyang Liu,Mengyao Gui,Hongwei Yang

DOI: https://doi.org/10.1016/j.chemosphere.2024.141503

IF: 8.8

2024-02-01

Chemosphere

Abstract:Recently, water contamination caused by the misuse of antibiotics has become a growing concern. In this study, an economical chitin/calcite composite (CCA) was extracted from crab shell waste, and the effects and mechanisms of its removal of ciprofloxacin (CIP) and tetracycline (TC) from aqueous solution were investigated. The functional groups of chitin and the metal phase of calcite gave CCA the ability to remove antibiotics. Experiments on kinetics, isothermal adsorption, thermodynamics, co-removal, and reusability were conducted to systematically explore the adsorption performances of CCA toward antibiotics. The pseudo-second-order (FSO) and Langmuir models suited the data obtained from experiments best and displayed a good fit for the chemisorption and a certain homogeneity of adsorption sites. At 25 °C, the maximum adsorption capacities (Qmax) toward CIP and TC were 228.86 and 150.76 mg g-1, respectively. The adsorption mechanisms of CCA with TC and CIP are pH dependent since pH can affect the surface charge of CCA and the form in which CIP and TC are existing. The X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) demonstrated that the keto-O and carboxyl groups of CIP and the carbonyl, hydroxyl, and amido groups of TC could be responsible for the binding with the calcite and the functional groups of chitin through surface complexation, cation bridge and hydrogen bonding.

environmental sciences
Dually organic modified bentonite with enhanced adsorption and desorption of tetracycline and ciprofloxacine

Zhongkai Wang,Yaseen Muhammad,Rui Tang,Caimei Lu,Sishan Yu,Rongrong Song,Zhangfa Tong,Biao Han,Hanbing Zhang

DOI: https://doi.org/10.1016/j.seppur.2021.119059

IF: 8.6

2021-11-01

Separation and Purification Technology

Abstract:Tetracycline (TC) and ciprofloxacin (CIP) cause serious environmental and health issues upon their uncontrolled release to the aquatic system and hence their control required serious attention. In this study, adsorption and desorption performances of TC and CIP by sodium carboxymethylcellulose (CMC) and polyethyleneimine (PEI) modified magnetic bentonite (MBCP) were explored. It was found that active functional groups such as –COOH, –OH and –NH2 loaded on the surface of MBCP increased the selective adsorption performance of MBCP for TC and CIP. Meanwhile, MBCP had superior adsorption performance in a wide pH range, magnetic separation capability and good regeneration. Based on the adsorption kinetics, isotherm, pHPZC, FE−SEM, TEM, FT−IR, XRD, BET, XPS and VSM results, the mechanisms of MBCP adsorption and desorption were investigated which mainly involved electrostatic interaction, pores deposition, complexation and ions exchange phenomena. MBCP was realized higher adsorption capacity for TC (476 mg/g), and CIP (457 mg/g) than MB (300 and 270 mg/g, respectively). This study provides important reference information for the fabrication of MBCP as a novel and promising adsorbent for the remediation of antibiotics from wastewater on the industrial level.

engineering, chemical

Empirically Based Strategies for Preventing Juvenile Delinquency.

Chitin-biocalcium as a novel superior composite for ciprofloxacin removal: Synergism of adsorption and flocculation

Carbon dioxide activated biochar-clay mineral composite efficiently removes ciprofloxacin from contaminated water - Reveals an incubation study

High-effective, convenient and environmental-friendly MOFs-chitosan-glyoxal composite film for ceftizoxime adsorption: Behavior and mechanisms

Adsorption kinetics, isotherms and mechanisms of three‐component covalent organic polymer/sodium alginate beads for ciprofloxacin removal from aqueous solution

Development of calcium phosphate-chitosan composites with improved removal capacity toward tetracycline antibiotic: Adsorption and electrokinetic properties

Elimination of Ciprofloxacin from Aqueous Solution by Ultrasonic-Assisted Adsorption Using Chitosan Crosslinked Graphene Oxide Nanoparticles

[Biochemical effects of genes].

Preparation of a Three-Dimensional Porous Graphene Oxide–Kaolinite–Poly(vinyl alcohol) Composite for Efficient Adsorption and Removal of Ciprofloxacin

Highly sulfonated hyper-cross-linked polymers as promising adsorbents for efficient and selective removal of ciprofloxacin from water

Hybrid process of adsorption and electrochemically based green regeneration of bentonite clay for ofloxacin and ciprofloxacin removal

Retention of Ciprofloxacin and Carbamazepine from Aqueous Solutions Using Chitosan-Based Cryostructured Composites

Carbon-Supported Nanocomposite Synthesis, Characterization, and Application as an Efficient Adsorbent for Ciprofloxacin and Amoxicillin

Simple fabrication of carboxymethyl cellulose and κ-carrageenan composite aerogel with efficient performance in removal of fluoroquinolone antibiotics from water

Removal of ciprofloxacin from water by millimeter-sized sodium alginate/H3PO4 activated corncob-based biochar composite beads

Potential of chitosan and activated carbon biocomposites for removing enrofloxacin and oxytetracycline from water

High-performance functional cellulose foam fabricated with theoretically optimized imidazolium salts for the efficient removal of ciprofloxacin

In-situ synthesis of MIL-100(Fe)@chitosan composite beads with hierarchical porous structure for efficient adsorption of chlortetracycline hydrochloride: Synthesis, performance and mechanisms

Synthesis of Eco-Friendly Biopolymer, Alginate-Chitosan Composite to Adsorb the Heavy Metals, Cd(II) and Pb(II) from Contaminated Effluents

Chitin/calcite composite extracted from shell waste as a low-cost adsorbent for removal of tetracycline and ciprofloxacin: Effects and mechanisms

Dually organic modified bentonite with enhanced adsorption and desorption of tetracycline and ciprofloxacine