Two hundredth anniversary of self-prediction of sudden, exertional cardiac death.

R. Bruce

DOI: https://doi.org/10.1016/0002-8703(72)90380-8

IF: 5.099

1972-09-01

American Heart Journal

Abstract:

What problem does this paper attempt to address?

Designing and Modifying of Lithium-Rich Layered Compound Based on Anion Redox

Dingguo Xia,Biao Li,Jin Ma,Yuxuan Zuo,Huijun Yan

DOI: https://doi.org/10.1149/ma2016-03/2/149

2016-01-01

ECS Meeting Abstracts

Abstract:Lithium ion batteries have been increasingly urged with high energy density and long cycle life to meet the increasing requirements for portable electronics, use of renewable energy and electric vehicles. The availability of the appropriate cathode material is crucial for the development of lithium ion batteries with high energy density. Lithium rich manganese-based layered oxides (LRMO), proposed by Amine, are considered to be the next generation promising cathode material owing to their high capacity and low cost. However, capacity fading and voltage decay hinder its application in practice. To overcome these problems, tremendous efforts have been made to realize electrochemical performance improvement, including partial element doping and the coating of active materials. The high capacity of LRMO is contributed by multiple electron process consisted of metal and oxygen redox. Many previous work demonstrated that the active oxygen redox is caused by the overlap between O 2p band and transition metal (TM) 3d band. Though providing extra capacity, the oxygen redox also brings the unstability of layered structure when gives excess electrons out. In our works, we proposed a general strategy to tune the electronic structure of layered oxides to improve the cycle performance by introducing polyanions into the local structure. We incorporated boron atoms into LRMO structure and found that boron atoms show high covalence with oxygen than metal atoms. This undermined the covalence of TM-O bond and lowered the top level of oxygen 2p band, which decreased overlap area between TM 3d band and O 2p band. We at last demonstrated a better LRMO cathode with higher stability (capacity retention is 94% at 20 mA/g for 80 cycles). The oxygen redox is essential for the multiple electron process providing high capacity. However, anionic redox has also been proved in conventional layered oxides like LiCoO2 and LiNi1/3Co1/3Mn1/3O2, but they show terrible stability and deliver capacity less than 200 mA h/g though with high theoretical capacity of about 270 mA h/g. This provokes a question about why these two types of layered oxides show different stability though with similar layered structure. In order to figure it out, we took a series of in situ investigation to study the geometric and electronic structural evolution of Li2RuO3 during charging/discharging, a typical lithium rich layered oxide with both of cation and anion redox. We found that lithium rich oxides show higher stability than conventional layered structure due to the superlattice structure. The extra lithium atoms in the transition metal layer will make the structure flexible and facilitate the distortion caused by oxygen redox upon deep delithiation. This enhances the stability of layered structure during lithiation and delithiation. Anionic redox can be deemed as a double-edged sword since it can provide extra capacity in the price of structural stability. Only when the anions give proper amounts of electrons can ensure high capacity and acceptable stability. Therefore, controllable anionic redox is required to develop optimal cathodes. We presented a work by doping different amounts of boron atoms in Li2RuO3. We found that Li2RuBxO3 (B=0, 0.02, 0.05, 0.1) show distinctive charge/discharge behavior since boron atoms can tune the electronic structure of oxygen and change the redox path. The obtained materials show different reversibility due to the variant redox path. This work is of great importance for the instruction of modification of such lithium rich layered oxides. Furthermore, anionic redox is instructive for the designing of new kinds of lithium rich high capacity electrodes. As studied in our work, we aware that the recipe of high capacity electrodes is multiple electron process, flexible structure and enough lithium ions. In addition to oxygen, sulfur is probably accessible to the multiple electron process as well. Hence, we developed lithium rich layered sulfides with high capacity of 200 mA h/g, which has a lower voltage and higher stability and safety compared with LRMO, and mild voltage decay is presented. This work will open a new scope for the development of high capacity electrodes. In summary, anionic redox is mysterious and needs to be deeply investigated, and it provides us a new direction for the modifying and designing of cathode materials. From oxygen to sulfur to selenium to tellurium, anions give amounts of possibilities for the developing of high capacity electrodes.
Tuning Oxygen Redox Chemistry in Li-Rich Mn-Based Layered Oxide Cathodes by Modulating Cation Arrangement.

Jicheng Zhang,Fangyi Cheng,Shulei Chou,Jianli Wang,Lin Gu,Heng Wang,Hirofumi Yoshikawa,Yong Lu,Jun Chen

DOI: https://doi.org/10.1002/adma.201901808

IF: 29.4

2019-01-01

Advanced Materials

Abstract:Li-rich Mn-based oxides (LRMO) are promising cathode materials to build next-generation lithium-ion batteries with high energy density exceeding 400 W h kg-1 . However, due to a lack of in-depth understanding of oxygen redox chemistry in LRMO, voltage decay is not resolved thoroughly. Here, it is demonstrated that the oxygen redox chemistry could be tuned by modulating cation arrangement. It declares that the materials with Li/Ni disorder and Li vacancies can inhibit the formation of OO dimers. Because of the high chemical activity, OO dimers could accelerate lattice oxygen release and NiO/spinel formation. The samples without forming OO dimers show improved performance in suppressing oxygen overoxidation and mitigating cation dissolution. As a result, the optimized cathode exhibits a high capacity over 280 mA h g-1 at 0.1 C and a high plateau voltage of 3.58 V with a very low voltage decay of 1.6% after 150 cycles at 1 C. This study opens an attractive path in designing Li-rich electrodes with stabilized redox chemistry.
A Mechanistic Insight into the Oxygen Redox of Li‐Rich Layered Cathodes and their Related Electronic/Atomic Behaviors Upon Cycling

Seongkoo Kang,Dayeon Choi,Hakwoo Lee,Byungjin Choi,Yong‐Mook Kang

DOI: https://doi.org/10.1002/adma.202211965

IF: 29.4

2023-03-17

Advanced Materials

Abstract:Li‐rich cathodes have been extensively investigated as their energy density is superior to Li stoichiometric cathode materials. In addition to the transition metal redox, this intriguing electrochemical performance originates from the redox reaction of the anionic sub‐lattice. This new redox process, the so‐called anionic redox or, more directly, oxygen redox in the case of oxides, almost doubles the energy density of Li‐rich cathodes compared to conventional cathodes. Numerous theoretical and experimental investigations have thoroughly established the current understanding of the oxygen redox of Li‐rich cathodes. However, different reports are occasionally contradictory, indicating that current knowledge remains incomplete. Moreover, several practical issues still hinder the real‐world application of Li‐rich cathodes. As these issues are related to phenomena resulting from the electronic to atomic evolution induced by unstable oxygen redox, a fundamental multiscale understanding is essential for solving the problem. In this review, we attempt to summarize the current mechanistic understanding of oxygen redox, the origin of the practical problems, and how current studies tackle the issues. This article is protected by copyright. All rights reserved

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Structural insights into composition design of Li-rich layered cathode materials for high-energy rechargeable battery

Chong Yin,Zhining Wei,Minghao Zhang,Bao Qiu,Yuhuan Zhou,Yinguo Xiao,Dong Zhou,Liang Yun,Cheng Li,Qingwen Gu,Wen Wen,Xiao Li,Xiaohui Wen,Zhepu Shi,Lunhua He,Ying Shirley Meng,Zhaoping Liu

DOI: https://doi.org/10.1016/j.mattod.2021.10.020

IF: 24.2

2021-12-01

Materials Today

Abstract:The Li-rich layered oxide is considered as one of the most promising cathode materials for high energy density batteries, due to its ultrahigh capacity derived from oxygen redox. Although incorporating over-stoichiometric Li into layered structure can generate Li2MnO3-like domain and enhance the oxygen redox activity thermodynamically, the fast and complete activation of the Li2MnO3-like domain remains challenging. Herein, we performed a systematic study on structural characteristics of Li-rich cathode materials to decipher the factors accounting for activation of oxygen redox. We reveal that the activation of Li-rich cathode materials is susceptible to local Co coordination environments. The Co ions can intrude into Li2MnO3-like domain and modulate the electronic structure, thereby facilitating the activation of Li-rich layered cathode materials upon first charging, leading to higher reversible capacity. In contrast, Li2MnO3-like domain hardly contains any Ni ions which contribute little to the activation process. The optimum composition design of this class of materials is discussed and we demonstrate a small amount of Co/Mn exchange in Li2MnO3-like domain can significantly promote the oxygen redox activation. Our findings highlight the vital role of Co ions in the activation of oxygen redox Li-rich layered cathode materials and provide new insights into the pathway toward achieving high-capacity Li-rich layered cathode materials.

materials science, multidisciplinary
Structurally robust lithium-rich layered oxides for high-energy and long-lasting cathodes

Ho-Young Jang,Donggun Eum,Jiung Cho,Jun Lim,Yeji Lee,Jun-Hyuk Song,Hyeokjun Park,Byunghoon Kim,Do-Hoon Kim,Sung-Pyo Cho,Sugeun Jo,Jae Hoon Heo,Sunyoung Lee,Jongwoo Lim,Kisuk Kang

DOI: https://doi.org/10.1038/s41467-024-45490-x

IF: 16.6

2024-02-12

Nature Communications

Abstract:Abstract O2-type lithium-rich layered oxides, known for mitigating irreversible transition metal migration and voltage decay, provide suitable framework for exploring the inherent properties of oxygen redox. Here, we present a series of O2-type lithium-rich layered oxides exhibiting minimal structural disordering and stable voltage retention even with high anionic redox participation based on the nominal composition. Notably, we observe a distinct asymmetric lattice breathing phenomenon within the layered framework driven by excessive oxygen redox, which includes substantial particle-level mechanical stress and the microcracks formation during cycling. This chemo-mechanical degradation can be effectively mitigated by balancing the anionic and cationic redox capabilities, securing both high discharge voltage (~ 3.43 V vs . Li/Li + ) and capacity (~ 200 mAh g −1 ) over extended cycles. The observed correlation between the oxygen redox capability and the structural evolution of the layered framework suggests the distinct intrinsic capacity fading mechanism that differs from the previously proposed voltage fading mode.

multidisciplinary sciences
Anionic redox behaviors of layered Li-rich oxide cathodes

Haoxiang Zhuo,Anbang Zhang,Xiaowei Huang,Jiantao Wang,Weidong Zhuang

DOI: https://doi.org/10.1039/d1qi00896j

IF: 7.779

2021-01-01

Inorganic Chemistry Frontiers

Abstract:Lithium-rich and manganese-based cathodes deliver extraordinary specific capacity with a unique anion redox, and the structural changes during the reaction from the anion keep it reversible and are accompanied by irreversible oxygen loss.

chemistry, inorganic & nuclear
Lithium Rich Layered Sulfides As a New-Type Cathode for Lithium Ion Batteries

Biao Li,Dingguo Xia,Jin Ma,Yuxuan Zuo,Huijun Yan,Hang Wei

DOI: https://doi.org/10.1149/ma2016-03/2/150

2016-01-01

ECS Meeting Abstracts

Abstract:Recent years more and more attention are paid on the exploration of lithium rich high capacity electrodes since the growing demand for high energy density lithium ion batteries for electric vehicles. In addition to the well-known lithium rich manganese based layered oxides, several lithium rich systems were proposed like ruthenium, molybdenum, and niobium based layered oxides[1-4]. Based on these work, we studied the recipe for the high capacity layered oxide cathodes and summarize it to be three aspects, namely sufficient lithium ions, multiple electron process, and flexible structure, of which the importance for the stabilization of the layered structure was demonstrated in our recent work[5]. The multiple electron process is usually realized by both the redox of metal and oxygen in these lithium rich oxides. However, though the oxygen ions can provide extra electrons accounting for the high capacity, excess oxidation of oxygen ions will result in destabilization of the structure and large irreversible capacity. Furthermore, the activation of the oxygen redox often happens at high voltage range, proposing quite high requirements for the electrolytes and leading to the unsafety concerns. Sulfur would be more superior choice than oxygen since polysulfide ions is more stable than peroxides or superoxides. On the other hand, sulfides have relatively lower voltage than oxides and provides access for the multiple electron process happening at a lower voltage range. The higher top of sulfur p state also will increase the electron mobility and thus the conductivity of the cathode. So the developing of lithium rich layered sulfides is a feasible route for the development of high capacity cathodes. In this work, we have developed a kind of lithium rich layered sulfides Li1.2Ti0.6Co0.2S2 for the first time based on the layered Li2MnO3-like structure Li2TiS3. Layered Li2TiS3 can’t deliver substantial capacity since the sole redox of sulfur will destabilize the structure. However, after we introduced active transition metal ions cobalt in the layered structure to substitute Ti atoms, the compound Li1.2Ti0.6Co0.2S2 can deliver capacity of more than 200 mA h/g at 20 mA/g. The first charge can only deliver 100 mAh/g which is contributed only by sulfur redox. On the later discharge, the capacity was increased to 200 mA h/g with a new redox of Ti4+/3+ is activated. The as-prepared new lithium rich layered sulfides can contribute more than 150 mA h/g for 100 cycles. The average voltage is only 2.4 V and will offer large safety than existing cathodes. This work will open a new area for the developing of lithium rich high capacity electrodes. References [1] N. Yabuuchi, M. Takeuchi, M. Nakayama, H. Shiiba, M. Ogawa, K. Nakayama, T. Ohta, D. Endo, T. Ozaki, T. Inamasu, K. Sato, S. Komaba, PNAS 2014, 343, 519. [2] M. Sathiya, K. Ramesha, G. Rousse, D. Foix, D. Gonbeau, A. S. Prakash, M. L. Doublet, K. Hemalatha, J.-M. Tarascon, Chem. Mater. 2013, 25, 1121. [3] M. Sathiya, G. Rousse, K. Ramesha, C. P. Laisa, H. Vezin, M. T. Sougrati, M. -L. Doublet, D. Foix, D. Gonbeau, W. Walker, A. S. Prakash, M. B. Hassine, L. Dupont, J. -M. Tarascon, Nat. Mater. 2013, 12, 827. [4] M. Sathiya, A. M. Abakumov, D. Foix, G. Rousse, K. Ramesha, M. Saubanère, M. L. Doublet, H. Vezin, C. P. Laisa, A. S. Prakash, D. Gonbeau, G. VanTendeloo, J. -M. Tarascon, Nat. Mater. 2015, 14, 230. [5] B. Li, R. Shao, H. Yan, L. An, B. Zhang, H. Wei, J. Ma, D. Xia, and X. Han, Adv. Funct. Mater. 2016, DOI: 10.1002/adfm.201504836. Figure 1
Lattice Oxygen Redox Reversibility Modulation in Enhancing the Cycling Stability of Li‐Rich Cathode Materials

Hualong Wu,Jiahao Dong,Yinggan Zhang,Liang Lin,Guiyang Gao,Tianyi Li,Xiaoli Yi,Baisheng Sa,Jiexi Wang,Laisen Wang,Jiantao Li,Khalil Amine,Dong‐Liang Peng,Qingshui Xie

DOI: https://doi.org/10.1002/adfm.202303707

IF: 19

2023-06-07

Advanced Functional Materials

Abstract:A facile and effective strategy is proposed to regulate the oxygen redox chemistry via foreign Fe doping and its induced intrinsic transition metal doping as well as the in situ constructed spinel surface layer. The modified cathode exhibits outstanding cycling stability with a superior capacity and voltage retentions of 92.5% and 90.8%, respectively, after 400 cycles at 1 C. The practical application of lithium‐rich layered oxides is prohibited by the drawbacks such as severe capacity and voltage degradation resulting from unstable oxygen redox environment and the accompanied irreversible oxygen release. Herein, a facile and effective strategy is proposed to regulate the oxygen redox chemistry via foreign Fe doping and its induced intrinsic transition metal (TM) doping as well as the in situ constructed spinel surface layer. The Fe doping, together with the induced intrinsic TM dual doping, can stabilize the lattice oxygen in the bulk due to the formed stronger FeO bond, and restrain the irreversible TM migration and then the undesirable phase transformation. More importantly, thermodynamical energy barrier of oxygen activation is dramatically decreased by the O 2p–Fe 3d charge‐transfer, allowing stable oxygen redox activity. And the pre‐constructed spinel layer can effectively stabilize the surface lattice oxygen and suppress harmful interfacial side‐reactions. Such a simple optimizing method make the modified cathode exhibit a high specific capacity of 298 mAh g−1 at 0.2 C, outstanding cycling stability with a superior capacity and voltage retentions of 92.5% and 90.8%, respectively, after 400 cycles at 1 C. This study provides a new direction for developing advanced Li‐ion batteries.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Stabilizing the Reversible Oxygen Redox Reactions in Lithium-Rich Layered Cathodes Via the Surface-to-Bulk Enhanced D-P Hybridization

Zijia Yin,Zijia Yin

DOI: https://doi.org/10.1149/ma2023-022350mtgabs

2023-12-22

ECS Meeting Abstracts

Abstract:The oxygen redox (OR) reaction in layered Li-rich oxide (LLO) cathode materials has been an attractive topic as it provides additional capacity. However, the suppression of the irreversible transition metal (TM) migration and oxygen release induced by the OR reaction is still a challenging issue, as it would lead to a severe capacity and voltage decay. Here, we introduce a surface-to-bulk structure modification strategy, namely surface Ni segregation and bulk Mo doping structure. Based on this strategy, the oxygen atoms near the surface are fully coordinated, and meanwhile the distortion of the metal–oxygen octahedron is alleviated in the bulk phase, thereby enhancing the degree of TM 3d and O 2p hybridization to stabilize the metal–oxygen framework for the OR reaction. It suppresses cation migration and oxygen release and maintains phase stability, allowing a reversible OR reaction. As a result, the capacity and voltage retention of the modified materials were significantly improved. This work gives an efficient method to stabilize the OR reaction through the surface-to-bulk enhanced d-p hybridization and provides new paths for the design of Li-rich cathodes.
Coupling the Electronic Distribution and Oxygen Redox Potential via Cu Substitution of Layered Oxide Cathodes for Sodium-Ion Batteries

Zeren Chen,Runxian Jiao,Hang Liu,Hualu Wang,Xiangyu Liu,Xiaoyu Zhang,Min Jia,Yuanping Chen,Xiaohong Yan

DOI: https://doi.org/10.1021/acssuschemeng.3c05369

IF: 8.4

2024-01-02

ACS Sustainable Chemistry & Engineering

Abstract:Anionic redox chemistry is extensively studied by virtue of the promising strategy for appealing to the large capacity in sodium-ion batteries (SIBs). However, stimulating the lattice oxygen activity generally occurs at high voltage suffering from irreversible oxygen release, transition metal ion migration, and even structural distortion, which is a critical limitation for their further application. In this study, a series of Na y Li0.1Cu x Mn0.9– x O2 cathode materials are developed by introducing Cu2+ into the transition metal layer. Theoretical calculations disclosed that the electron agglomeration around the O atom has been enhanced with the increase of Cu content, leading to a strong covalent bonding between Cu and O and contributing to a more stable structure. The local structure facilitates the loss of electrons, thus reducing the O redox potential along the charging process, which is further confirmed by an experimental study. Besides, the Cu substitution introduced a whole solid solution reaction during the charge–discharge process with small volume change, hence greatly improving the cycling performance of NLCMO systems. Our research provides unique insights into the activation mechanism of anionic redox reactions and provides critical guidance in further designing anionic redox-based layered oxide systems.

chemistry, multidisciplinary,engineering, chemical,green & sustainable science & technology
A Redox Couple Strategy Enables Long‐Cycling Li‐ and Mn‐Rich Layered Oxide Cathodes by Suppressing Oxygen Release

Qinong Shao,Panyu Gao,Chenhui Yan,Mingxi Gao,Wubin Du,Jian Chen,Yaxiong Yang,Jiantuo Gan,Zhijun Wu,Chenyang Zhang,Gairong Chen,Xusheng Zheng,Yue Lin,Yinzhu Jiang,Wenping Sun,Yongfeng Liu,Mingxia Gao,Hongge Pan

DOI: https://doi.org/10.1002/adma.202108543

IF: 29.4

2022-02-24

Advanced Materials

Abstract:Li- and Mn-rich layered oxides (LMROs) are considered the most promising cathode candidates for next-generation high-energy lithium-ion batteries. The poor cycling stability and fast voltage fading resulting from oxygen release during charging, however, severely hinders their practical application. Herein, a strategy of introducing an additional redox couple is proposed to eliminate the persistent problem of oxygen release. As a proof of concept, the cycling stability of Li1.2 Ni0.13 Co0.13 Mn0.54 O2 , which is a typical LMRO cathode, is substantially enhanced with the help of the S2- /SO3 2- redox couple, and the capacity shows no decay with a retention of 100% after 700 cycles at 1C, far superior to the bare counterpart (61.7%). The surface peroxide ions (O2 2- ) are readily chemically reduced back to immobile O2- by S2- during charging, accompanied by the formation of SO3 2- , which plays a critical role in stabilizing the oxygen lattice and eventually inhibiting the release of oxygen. More importantly, the S2- ions are regenerated during the following discharging process and participate in the chemical redox reaction again. The findings shed light on a potential direction to tackle the poor cycling stability of high-energy anion-redox cathode materials for rechargeable metal-ion batteries.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Inherent inhibition of oxygen loss by regulating superstructural motifs in anionic redox cathodes

Jiajie Liu,Rui Qi,Changjian Zuo,Cong Lin,Wenguang Zhao,Ni Yang,Jianyuan Li,Junliang Lu,Xin Chen,Jimin Qiu,Mihai Chu,Mingjian Zhang,Cheng Dong,Yinguo Xiao,Haibiao Chen,Feng Pan

DOI: https://doi.org/10.1016/j.nanoen.2021.106252

IF: 17.6

2021-10-01

Nano Energy

Abstract:The capacity of the layered oxide cathode in a sodium ion battery can be increased by harnessing anionic redox. However, the extra capacity induced by anionic redox comes at the expense of reversibility due to the irreversible oxidation and subsequent loss of oxygen. Here, we report a universal strategy of improving the reversibility of oxygen redox in sodium layered oxides by regulating the superstructural motifs. The intrinsic chemical properties of superstructural motifs can be directionally altered by modulating the interionic interactions, and the rational integration of selected superstructural motifs can result in advanced materials with target performance. As a demonstration, a novel cathode comprising both 6 and 6 superstructural motifs is designed and synthesized with inherently inhibited oxygen loss and significantly improved cyclic reversibility. Detailed characterizations on the atomic-level structure and chemistry of materials revealed that the pinning effect of the 6 superstructural motif is critical to maintain a stable layered structure. The findings from this work open up new routes for the design and development of next-generation high energy cathodes with target performance.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
Improving the oxygen redox reversibility of Li-rich battery cathode materials via Coulombic repulsive interactions strategy

Qingyuan Li,De Ning,Deniz Wong,Ke An,Yuxin Tang,Dong Zhou,Götz Schuck,Zhenhua Chen,Nian Zhang,Xiangfeng Liu

DOI: https://doi.org/10.1038/s41467-022-28793-9

IF: 16.6

2022-03-02

Nature Communications

Abstract:Abstract The oxygen redox reaction in lithium-rich layered oxide battery cathode materials generates extra capacity at high cell voltages (i.e., >4.5 V). However, the irreversible oxygen release causes transition metal (TM) dissolution, migration and cell voltage decay. To circumvent these issues, we introduce a strategy for tuning the Coulombic interactions in a model Li-rich positive electrode active material, i.e., Li 1.2 Mn 0.6 Ni 0.2 O 2 . In particular, we tune the Coulombic repulsive interactions to obtain an adaptable crystal structure that enables the reversible distortion of TMO 6 octahedron and mitigates TM dissolution and migration. Moreover, this strategy hinders the irreversible release of oxygen and other parasitic reactions (e.g., electrolyte decomposition) commonly occurring at high voltages. When tested in non-aqueous coin cell configuration, the modified Li-rich cathode material, combined with a Li metal anode, enables a stable cell discharge capacity of about 240 mAh g −1 for 120 cycles at 50 mA g −1 and a slower voltage decay compared to the unmodified Li 1.2 Mn 0.6 Ni 0.2 O 2 .

multidisciplinary sciences
Regulating oxygen covalent electron localization to enhance anionic redox reversibility of lithium-rich layered oxide cathodes

Chunxiao Zhang,Bo Wei,Meiyu Wang,Datong Zhang,Tomoki Uchiyama,Chaoping Liang,Libao Chen,Yoshiharu Uchimoto,Ruifeng Zhang,Peng Wang,Weifeng Wei

DOI: https://doi.org/10.1016/j.ensm.2022.01.038

IF: 20.4

2022-04-01

Energy Storage Materials

Abstract:Anionic redox and cationic redox chemistries enable Li-rich layered oxides to achieve ultrahigh specific capacities. Unfortunately, the irreversible nature of anionic redox participated by lattice oxygen causes the irreversible release of oxygen, leading to severe structural degradation and side reactions, which causes capacity/voltage fading. Herein, to solve the longstanding problem of anionic redox irreversibility, we propose a La/Al co-doping strategy involving the tuning of the fine electronic structures of a Co-free Li1.2Mn0.533Ni0.267O2 cathode, which consequently suppresses the release of lattice oxygen during cycling. We discover that the strong La-O and Al-O bonds weaken the covalency of TM-O bonds and promote covalent electron localization to oxygen, thereby facilitating Li+ migration and inhibiting the irreversible release of lattice oxygen. In addition, the induced layered-rocksalt heteroepitaxial interface effectively stabilizes the crystal structure and reduces side reactions at the electrode–electrolyte interface. As a result, the co-doped LMNLAO shows outstanding cycling stability with a capacity retention of 93.6% after 200 cycles and a least voltage attenuation of 1.35 mV/cycle significantly exceeding those of pristine LMNO. This strategy allows the regulation of the electronic structure to enhance the reversibility and reactivity of anion redox reactions, it can be applied for the development of other high-capacity cathodes.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology
Insight into the Redox Chemistry of Layered LiNiO2-YSy Cathode Material: A First-Principles Study

Huijun Yan,Dingguo Xia,Biao Li,Yuxuan Zuo,Hang Wei,Junli Kong,Xiaochun Chu

DOI: https://doi.org/10.1149/ma2016-03/2/1226

2016-01-01

ECS Meeting Abstracts

Abstract:With the rapid development of Li-ion batteries, their application to the electric vehicles (EVs) and hybrid electric vehicles (HEVs) would be expected. In recent years, Ni-based layered oxide cathode materials, such as LiNi1/3Co1/3Mn1/3O2 (NCM) and LiNi0.8Co0.15Al0.05O2 (NCA), garner considerable attention in lithium ion batteries due to their relative high energy density [1-2]. However, the safety concern of the batteries associated with the oxygen release, which is a large problem resulting from the instability of cathode and decomposition of electrolyte[3-4], should be further resolved for practical application. The layered oxides LiTMO2 (TM=Ni, Co) become unstable in a highly delithiated state. On one hand, the extraction of more and more lithium ions gives rise to the overlapping of TM-3d band with O-2p band, which will increase the oxygen participation in the redox chemistry and causes destabilization of the lattice. On the other hand, upon oxidation (i.e. delithiation), increasing amount of unstable Ni4+(Co4+) will be formed, followed by the reduction to Ni3+(Co3+) at elevated temperatures with concurrent loss of oxygen. Meanwhile, the high voltage required for deep charging would oxidize electrolyte, thereby resulting in oxygen release and capacity fade. Therefore, the deep charging of layered oxide cathodes involving the anion oxidation would accelerate oxygen release, which seriously affects the safety of batteries. Some research efforts have been performed to enhance the safety by doping with anions[5-6]. However, the mechanisms of redox chemistry in systems where multiple anions coexist remain unclear so far. The stability and safety of layered-oxysulfide cathode by tuning the redox chemistry were studied based on first-principles. Since the Ni-based cathodes have more favorable prospect in the future, we chose LiNiO2, the representative of the layered-oxide cathode, as a model in calculations. LiNiO2-ySy, wherein oxygen anions are partially substituted by sulfur anions, was also studied. In order to understand the role of S2- in enhancing the stability and safety, the redox chemistry that occurs in S-substituted systems was discussed in detail. For Li1-xNiO1.89S0.11, at the initial charging stage (0≤x≤0.33), the sulfur anions alongside nickel and oxygen atoms are all involved in the charge compensation, although sulfur anions contribute less to the process. In the next charging stage (x＞0.33), only nickel and oxygen atoms become oxidized owing to the donation of electrons, while sulfur anions are not involved. The partial oxidation of sulfur provides a novel line of thought in terms of designing the Li-rich layered cathode materials with charge compensation by multiple anions. References [1] T. Hayashi, J. Okada, E. Toda, R. Kuzuo, N. Oshimura, N. Kuwata, J. Kawamura, J. Electrochem. Soc. 2014, 161, A1007 [2] S.-K. Jung, H. Gwon, J. Hong, K.-Y. Park, D.-H. Seo, H. Kim, J. Hyun, W. Yang, K. Kang, Adv. Energy Mater. 2014, 4, 1. [3] K.-W. Nam, S.-M. Bak, E. Hu, X. Yu, Y. Zhou, X. Wang, L. Wu, Y. Zhu, K.-Y. Chung, X.-Q. Yang, Adv. Funct. Mater. 2013, 23, 1047. [4] J. Hong, H.-D. Lim, M. Lee, S.-W. Kim, H. Kim, S.-T. Oh, G.-C. Chung, K. Kang, Chem. Mater. 2012, 24 2692. [5] D.-W. Han, W.-H. Ryu, W.-K. Kim, J.-Y. Eom, H.-S. Kwon, J. Phys. Chem. C 2013, 117, 4913 [6] S.-H. Park, Y.-K. Sun, K.-S. Park, K.-S. Nahm, Y.-S. Lee, M. Yoshio, Electrochim. Acta 2002, 47, 1721
Stabilizing Anionic Redox Chemistry in a Mn‐Based Layered Oxide Cathode Constructed by Li‐Deficient Pristine State

Xin Cao,Haifeng Li,Yu Qiao,Min Jia,Xiang Li,Jordi Cabana,Haoshen Zhou

DOI: https://doi.org/10.1002/adma.202004280

IF: 29.4

2020-12-03

Advanced Materials

Abstract:Li‐rich cathode materials are of significant interest for coupling anionic redox with cationic redox chemistry to achieve high‐energy‐density batteries. However, lattice oxygen loss and derived structure distortion would induce serious capacity loss and voltage decay, further hindering its practical application. Herein, a novel Li‐rich cathode material, O3‐type Li0.6[Li0.2Mn0.8]O2, is developed with the pristine state displaying both a Li excess in the transition metal layer and a deficiency in the alkali metal layer. Benefiting from stable structure evolution and Li migration processes, not only can high reversible capacity (≈329 mAh g−1) be harvested but also irreversible/reversible anionic/cationic redox reactions are comprehensively assigned via the combination of in/ex situ spectroscopies. Furthermore, irreversible lattice oxygen loss and structure distortion are effectively restrained, resulting in long‐term cycle stability (capacity drop of 0.045% per cycle, 500 cycles). Altogether, tuning the Li state in the alkali metal layer presents a promising way for modification of high‐capacity Li‐rich cathode candidates.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Sulfuration of Li‐Rich Mn‐Based Cathode Materials for Multianionic Redox and Stabilized Coordination Environment

Kun Zhang,Jizhen Qi,Jin Song,Yuxuan Zuo,Yali Yang,Tonghuan Yang,Tao Chen,Xi Liu,Liwei Chen,Dingguo Xia

DOI: https://doi.org/10.1002/adma.202109564

IF: 29.4

2022-02-04

Advanced Materials

Abstract:Lithium-rich transition metal oxides (LLOs) can deliver high specific capacity over 250 mAh g-1 , stemming from additional contribution of oxygen redox. However, the formation of O(2- n )- (0 < n < 2) species and even oxygen gas during the deep oxidation stage leads to progressive structural transformation that cause voltage decay/hysteresis, sluggish kinetics, and poor thermostability, preventing real-world application of LLOs. Therefore, the substantive key relies on enhancing the anionic redox stability in LLOs. Here, a sulfuration procedure of LLOs (S-LLOs) is proposed, in which sulfur anions are incorporated into oxygen sites in the lattice structure and form polyanions on the surface. Proved by structural characterizations and density functional theory (DFT) calculations, sulfur anions in the interior lattice can reversibly participate in the redox process and enhance the integral coordination stability by mitigating undesired oxygen redox. Moreover, S polyanions at the surface form a protecting layer for interfacial stability. The electrochemical measurements indicate that S-LLO demonstrates a high discharge capacity of 307.8 mAh g-1 , an outstanding capacity retention rate of 91.5% after 200 cycles, along with excellent voltage maintenance, rate capability, and thermostability. The sulfuration process of LLOs with multianionic redox mechanism highlights a promising strategy to design novel high-energy-density cathode materials with superior cycling performance.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Weak σ–π–σ Interaction Stabilizes Oxygen Redox towards High-Performance Li–rich Layered Oxide Cathodes

Xin Guo,Jie Li,Yu Zhang,Xu Zhang,Jihong Liu,Wenting Li,Lisi Lu,Guixiao Jia,Shengli An,Xinping Qiu

DOI: https://doi.org/10.1016/j.nanoen.2024.109390

IF: 17.6

2024-02-13

Nano Energy

Abstract:The aggregation of Li 2 MnO 3 –like domains in Li-rich layered oxides (LLOs) causes severe capacity/voltage fading, which seriously impedes their commercial applications. Here, we design Co–free LLO models with well–dispersed Li 2 MnO 3 –like domains (D–LNMO) and aggregated Li 2 MnO 3 –like domains (A–LNMO) to investigate the oxygen redox process and structural stability. It is found that low oxygen partial pressure can disperse Li 2 MnO 3 –like domains by forming stable ONiMn 4+ Mn 3+ Li 3 coordination configurations so that D-LNMO is predominant. Moreover, a novel oxygen oxidation mechanism involving a weak σ–π–σ interaction where oxygen redox in OTM 2 MnLi 3 (TM = Ni, Mn) configurations is triggered by O in Li-O-Li configurations is revealed. Specifically, the lattice oxygen at the interface of Li 2 MnO 3 –like domains and LiTMO 2 domains can be activated, which is beyond conventional Li-O-Li configuration. Due to the abundance of interfacial lattice oxygen in D–LNMO, more lattice oxygen participates in charge compensation, thereby relieving the oxidation load of oxygen ions, suppressing lattice oxygen release, and delaying irreversible structural transformation. Consequently, D-LNMO possesses highly reversible oxygen redox and exceptional structural stability, exhibiting superior cycling stability of high capacity. The findings provide new perspectives and concepts for designing high-energy Li-rich cathodes.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
Unveiling the Complementary Manganese and Oxygen Redox Chemistry for Stabilizing the Sodium‐Ion Storage Behaviors of Layered Oxide Cathodes

Junteng Jin,Yongchang Liu,Qiuyu Shen,Xudong Zhao,Jian Zhang,Yuzhu Song,Tianyu Li,Xianran Xing,Jun Chen

DOI: https://doi.org/10.1002/adfm.202203424

IF: 19

2022-05-05

Advanced Functional Materials

Abstract:A complementary Mn and O redox mechanism, namely, the gradually activated Mn3+/Mn4+ redox capacities associated with partial oxygen release upon cycling could effectively compensate the capacity loss from O2–/On– redox, is first proposed to explain the admirable cycling stability of Mn‐based layered oxide cathodes for sodium‐ion batteries. Layered oxide cathodes for sodium‐ion batteries (SIBs) have drawn increasing attention owing to their fascinating additional capacity contributed by oxygen‐redox chemistry. Unfortunately, excessive oxygen redox incurs an irreversible oxygen release, deteriorating the cyclic stability and compromising the advantage of additional capacity. Significant efforts have been made so far to stabilize lattice oxygen, but the potential advantages associated with oxygen loss have been ignored. Herein, a complementary Mn and O redox mechanism is first revealed in a novel P2‐Na0.75Ca0.04[Li0.1Ni0.2Mn0.67]O2 cathode. The partial oxygen release activates more Mn3+/Mn4+ redox capacities upon cycling, which effectively compensate the capacity loss from O2‐/On‐ redox and thus enable an ultra‐stable cycling performance (capacity retentions of 102.1% and 95.2% over 100 and 200 cycles at 5 C, respectively). The fast Na+ diffusion kinetics of the cathode also ensure an exceptional rate capability (133.1 and 68.8 mAh g‐1 at 0.1 and 20 C, respectively). The electrode crystal/electronic structure evolution and charge compensation mechanism upon sodiation/desodiation have been elucidated via systematic operando measurements and theoretical computations. The complementary chemistry is a universal principle that stabilizes the Na‐storage behaviors of Mn‐based oxide cathodes, providing new opportunities for anionic redox to boost the energy density and cycling life of SIBs simultaneously.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Enhancing Sulfur Redox Conversion of Active Iron Sites by Modulation of Electronic Density for Advanced Lithium‐Sulfur Battery

Fanchao Zhang,Zihuan Tang,Tengfei Zhang,Hong Xiao,Huifeng Zhuang,Xiao Liang,Lirong Zheng,Qiuming Gao

DOI: https://doi.org/10.1002/smtd.202300519

IF: 12.4

2023-06-23

Small Methods

Abstract:Single‐molecule iron species are anchored on N and P dual‐doped porous carbon nanosheets (Fe‐NPPC) via axial Fe‐N coordination to optimize the electronic structure of active sites. The Fe‐NPPC with Fe‐N5 sites can boost polysulfide catalytic conversion by modulation of electronic density in active moieties, endowing Li‐S batteries with high reversible capacity and cycling stability. Despite lithium‐sulfur (Li‐S) batteries possessing ultrahigh energy density as great promising energy storage devices, the suppressing shuttle effect and improving sulfur redox reaction (SROR) are vital for their practical application. Developing high‐activity electrocatalysts for enhancing the SROR kinetics is a major challenge for the application of Li‐S batteries. Herein, single‐molecule iron phthalocyanine species are anchored on the N and P dual‐doped porous carbon nanosheets (Fe‐NPPC) via axial Fe‐N coordination to optimize the electronic structure of active centers. The Fe‐NPPC can promote the catalytic conversion of polysulfides by modulation of the electronic density in active moieties, endowing the Li‐S battery with a high reversible capacity of 1023 mAh g−1 at 1 C as well as an ultralow capacity decay of 0.035% per cycle over 1500 cycles. Even with a high sulfur loading of 7.1 mg cm−2, the Li‐S battery delivers a high areal capacity of 4.8 mAh cm−2 after 150 cycles at 0.2 C. With further increasing the sulfur loading to 9.2 mg cm−2, an excellent areal capacity of up to 9.3 mAh cm−2 is obtained at 0.1 C.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology

Two hundredth anniversary of self-prediction of sudden, exertional cardiac death.

Designing and Modifying of Lithium-Rich Layered Compound Based on Anion Redox

Tuning Oxygen Redox Chemistry in Li-Rich Mn-Based Layered Oxide Cathodes by Modulating Cation Arrangement.

A Mechanistic Insight into the Oxygen Redox of Li‐Rich Layered Cathodes and their Related Electronic/Atomic Behaviors Upon Cycling

Structural insights into composition design of Li-rich layered cathode materials for high-energy rechargeable battery

Structurally robust lithium-rich layered oxides for high-energy and long-lasting cathodes

Anionic redox behaviors of layered Li-rich oxide cathodes

Lithium Rich Layered Sulfides As a New-Type Cathode for Lithium Ion Batteries

Lattice Oxygen Redox Reversibility Modulation in Enhancing the Cycling Stability of Li‐Rich Cathode Materials

Stabilizing the Reversible Oxygen Redox Reactions in Lithium-Rich Layered Cathodes Via the Surface-to-Bulk Enhanced D-P Hybridization

Coupling the Electronic Distribution and Oxygen Redox Potential via Cu Substitution of Layered Oxide Cathodes for Sodium-Ion Batteries

A Redox Couple Strategy Enables Long‐Cycling Li‐ and Mn‐Rich Layered Oxide Cathodes by Suppressing Oxygen Release

Inherent inhibition of oxygen loss by regulating superstructural motifs in anionic redox cathodes

Improving the oxygen redox reversibility of Li-rich battery cathode materials via Coulombic repulsive interactions strategy

Regulating oxygen covalent electron localization to enhance anionic redox reversibility of lithium-rich layered oxide cathodes

Insight into the Redox Chemistry of Layered LiNiO2-YSy Cathode Material: A First-Principles Study

Stabilizing Anionic Redox Chemistry in a Mn‐Based Layered Oxide Cathode Constructed by Li‐Deficient Pristine State

Sulfuration of Li‐Rich Mn‐Based Cathode Materials for Multianionic Redox and Stabilized Coordination Environment

Weak σ–π–σ Interaction Stabilizes Oxygen Redox towards High-Performance Li–rich Layered Oxide Cathodes

Unveiling the Complementary Manganese and Oxygen Redox Chemistry for Stabilizing the Sodium‐Ion Storage Behaviors of Layered Oxide Cathodes

Enhancing Sulfur Redox Conversion of Active Iron Sites by Modulation of Electronic Density for Advanced Lithium‐Sulfur Battery