Abstract:In this study, a mixed-acid-assisted system utilizing a combination of a weak acid (citric acid, CA) and strong acid (H2SO4, SA) under hydrothermal reaction conditions was proposed for simultaneous preparation and modification (carboxylation) of cellulose nanocrystals (CNCs). Bleached bamboo pulp was used as the cellulose source, and the optimized reaction conditions were further used to produce carboxylated CNCs (cCNCs) from microcrystalline cellulose and Whatman 1 filter paper. Different concentrations of CA and SA (namely, 40 wt % CA (optimized concentration) and 5, 10, 20, and 30 wt % SA) were used for the hydrolytic processing of raw cellulosic material under hydrothermal conditions. The effect of various concentrations of CA and SA on the yield, carboxylate content, microstructure, crystallinity, thermal, and rheological characteristics of cCNCs were methodically investigated and contrasted. The optimized hydrothermal reaction conditions performed for 4 h at 100 degrees C using a mixture of 40 wt % CA and only 20 wt % SA yielded needle-shaped cCNCs with a yield higher than 70%. The carboxyl functionalization of CNCs was affirmed through Fourier transform infrared spectroscopy and conductometric titrimetric method. The results revealed the carboxylate content of 1.18 mmol/g corresponding to an average degree of oxidation of similar to 0.20. The length of nanocrystals lies in the range of 280-420 nm with diameter ranging from 10 to 20 nm, as was perceived through microstructural analytical tools like field emission scanning electron microscopy, transmission electron microscopy, and atomic force microscopy. Dynamic light scattering analysis gives an average size of similar to 200 nm. The visual inspection revealed high colloidal stability of cCNCs dispersions, which was further supported through its appreciable Zeta potential value of ca. -49.5 mV. Further, the rheological characterizations revealed typical features reminiscent of critical gels showing elastic behavior of cCNCs. Nanocomposite films of hydroxypropyl methylcellulose (HPMC) with different loadings of cCNCs were fabricated using a simple solvent casting method. The incorporation of very small amounts of cCNCs (0.1 wt %) in HPMC resulted in similar to 58% increment in tensile strength, similar to 10% increment in modulus, and similar to 82% increment in elongation. Moreover, the composite films exhibited high transparency and appreciable water barrier properties that allow their potential application as barrier and transparent films for various applications.

Oxidation with potassium ferrate for the one-pot preparation of carboxylated cellulose II nanocrystals

Large-Scale Preparation of Carboxylated Cellulose Nanocrystals and Their Application for Stabilizing Pickering Emulsions

Investigation of a Widely Applicable Process for Extracting Carboxyl-rich Cellulose Nanocrystal (CNC)

Efficient extraction of carboxylated nanocellulose from ionoSolv pulps with alkaline H2O2 assisted oxidation

Novel Carboxylated Cellulose Nanocrystals Synthesized by Co-Oxidation of Sodium Periodate/fenton As a Green Solid Emulsifier for Oil-in-water Pickering Emulsion.

One-pot treatment of cellulose using iron oxide catalysts to produce nanocellulose and water-soluble oxidised cellulose

Mixed-Acid-Assisted Hydrothermal Process for Simultaneous Preparation and Carboxylation of Needle-Shaped Cellulose Nanocrystals

Efficient, Self‐Terminating Isolation of Cellulose Nanocrystals through Periodate Oxidation in Pickering Emulsions

Efficient, self-terminating isolation of cellulose nanocrystals via periodate oxidation in Pickering emulsions.

Highly Efficient and Sustainable Preparation of Carboxylic and Thermostable Cellulose Nanocrystals Via FeCl3-Catalyzed Innocuous Citric Acid Hydrolysis

Highly Efficient and Sustainable Preparation of Carboxylic and Thermostable Cellulose Nanocrystals via FeCl 3 -Catalyzed Innocuous Citric Acid Hydrolysis

One-pot preparation of hydrophobic cellulose nanocrystals in an ionic liquid

Extraction of Cellulose Nano-Crystals from Old Corrugated Container Fiber Using Phosphoric Acid and Enzymatic Hydrolysis Followed by Sonication.

Cellulose Nanocrystals (cncs) with Different Crystalline Allomorph for Oil in Water Pickering Emulsions.

Using a Fully Recyclable Dicarboxylic Acid for Producing Dispersible and Thermally Stable Cellulose Nanomaterials from Different Cellulosic Sources

Preliminary Investigations of the Mechanisms Involved in the Ultrasonication-Assisted Production of Carboxylic Cellulose Nanocrystals with Different Structural Carboxylic Acids

Comprehensive utilization strategy of cellulose in a facile, controllable, high-yield preparation process of cellulose nanocrystals using aqueous tetrabutylphosphonium hydroxide

Facile and Rapid One-Step Extraction of Carboxylated Cellulose Nanocrystals by H2SO4/HNO3 Mixed Acid Hydrolysis.

Cellulose Nanocrystal Preparation via Rapid Hydrolysis of Wood Cellulose Fibers Using Recyclable Molten Ferric Chloride Hexahydrate

Ecofriendly Preparation of Cellulose Nanocrystal-Coated Polyimide Fiber: Strategy for Improved Wettability

Green fabrication of thermally-stable oxidized cellulose nanocrystals by evolved Fenton reaction and in-situ nanoreinforced thermoplastic starch