Abstract:Contact plates, dipslides, and swabs are used for the microbiological monitoring of surfaces in controlled environments such as pharmaceutical clean rooms. In the present study, three different swab types using two different methods (direct streaking on agar versus elution followed by membrane filtration) were evaluated. In a first study, representative surfaces in pharmaceutical clean rooms were artificially inoculated using three different environmental strains (in vitro study). In a second study, a naturally inoculated floor was swabbed with the same three swab types, again using the two different recovery methods (in situ study). With the in vitro study, clear differences were found between the three swab types as well as between the two recovery methods. In addition, recovery rate of the swab type was dependent on the recovery method (interactive effect). One swab type showed a higher recovery rate with direct streaking on agar, while the other swab type showed better results using the elution/membrane filtration method. This difference can be explained by the fact that both swabs were each developed for their specific application. The type of surface also had a highly significant effect on the recovery rates. Recovery on stainless steel was better than for the other surfaces, while lexan had the lowest recovery rate. From the three different strains applied in the in vitro study, Micrococcus luteus had significantly higher recovery results compared to the other two strains (Bacillus thuringiensis, Aspergillus brasiliensis). The differences in recovery between the swab type and recovery method were less pronounced in the in situ study. In particular, the recovery of the swab type depending on the recovery method was not found. In conclusion, if swabs are to be used for environmental monitoring, their suitability should first be evaluated. This can be approached with artificially inoculated surfaces. However, naturally inoculated surfaces might be more realistic and might better reflect what is found in pharmaceutical clean rooms.LAY ABSTRACT: Environmental microbiological monitoring provides information on the hygiene condition of pharmaceutical clean rooms and equipment for manufacturing of drug products. Different methods can be used to recover microorganisms. For surfaces, normally contact plates (e.g., RODAC or dipslides) are used; however, when surfaces are uneven, swabs should be used. In the present study three different swabs were evaluated for their ability to recover microorganisms from different surfaces. Thereby two methods and two approaches were evaluated. Swab samples were either directly stroked on agar or the swab was eluted, membrane-filtrated, and the filter placed on an agar plate. Experimentally, artificial inoculated surfaces typically found in clean rooms (in vitro study) and naturally inoculated floors (in situ study) were sampled. Thus with this approach the most convenient swab and the most suitable recovery methods under laboratory as well as real clean room conditions were evaluated. With this set-up, we found the most suitable swab for our environmental monitoring not only by using artificial inoculated surfaces but also under more realistic clean room conditions, which is most important for microbiological environmental monitoring sampling.

Novel sampling technique maintaining the two-dimensional organization of microbes during cultivation from chronic wounds: The Imprint method

Bactogram: Spatial Analysis of Bacterial Colonization in Epidermal Wounds

Bactogram: Spatial Analysis of Bacterial Colonisation in Epidermal Wounds

Assessment and Monitoring of the Wound Micro-Environment in Chronic Wounds Using Standardized Wound Swabbing for Individualized Diagnostics and Targeted Interventions

Modified in-vitro AATCC-100 procedure to measure viable bacteria from wound dressings

The chronic wound characterisation study and biobank: a study protocol for a prospective observational cohort investigation of bacterial community composition, inflammatory responses and wound-healing trajectories in non-healing wounds

Comparison of an automated DNA extraction and 16S rDNA real time PCR/sequencing diagnostic method using optimized reagents with culture during a 15-month study using specimens from sterile body sites

Assessing Biofilm at the Bedside: Exploring Reliable Accessible Biofilm Detection Methods

Evaluation of the impact of six different DNA extraction methods for the representation of the microbial community associated with human chronic wound infections using a gel-based DNA profiling method

The microbiome of diabetic foot ulcers: a comparison of swab and tissue biopsy wound sampling techniques using 16S rRNA gene sequencing

Rapid detection of biofilm with modified alcian blue staining: In‐vitro protocol improvement and validation with clinical cases

The Wound Microbiome: Modern Approaches to Examining the Role of Microorganisms in Impaired Chronic Wound Healing

Novel Diagnostic Technologies and Therapeutic Approaches Targeting Chronic Wound Biofilms and Microbiota

Clinical perspectives on sampling and processing approaches for the management of infection in diabetic foot ulceration: A qualitative study

Early wound infection monitoring via headspace O2 micro-respirometry

The Visualization of Biofilms in Chronic Diabetic Foot Wounds Using Routine Diagnostic Microscopy Methods

A high-precision wound healing assay based on photosensitized culture substrates

Sampling Techniques and Genomic Analysis of Biological Material from Artworks

Evaluation of the Recovery Rate of Different Swabs for Microbial Environmental Monitoring

An Advanced Tape-Stripping Approach for High-Efficiency Sampling on Non-Absorbent Surfaces.

Development, characterisation and evaluation of a simple polymicrobial colony biofilm model for testing of antimicrobial wound dressings