Abstract:Three-dimensional (3D) printing is a bio-fabrication technique used to process tissue-engineered scaffolds for bone repair and remodeling. Polycaprolactone (PCL)/β-tricalcium phosphate (TCP) has been used as a base and osteoconductive biomaterial for bone tissue engineering in the past decades. The current study reveals the fabrication of a polycaprolactone (PCL)/β-tricalcium phosphate (TCP) scaffold by incorporating carbon nanotubes (CNT) via 3D printing. The physical properties and cytocompatibility of a new type of tissue engineering composite from polycaprolactone/β-tri-calcium phosphate/carbon nanotubes were investigated, and it was an absorbable scaffold prepared via furnace deposition 3D printing technology. The scaffold was designed with CAD software, and the composite material was fabricated via 3D printing. The printed composite material was tested for mechanical strength, scanning electron microscope (SEM) analysis, porosity calculation, systemic toxicity test, hemolysis rate determination, and effect on the proliferation of rat adipose-derived stem cells cultured in vitro. A composite scaffold with a length of 15 mm, width of 10 mm, and height of 5 mm was manufactured through CAD software drawing and 3D printing technology. Scanning electron microscopy measurements and analysis of the internal pore size of the stent are appropriate; the pores are interconnected, and the mechanical strength matches the strength of human cancellous bone. The calculated porosity of the stent was >60%, non-toxic, and non-hemolytic. The proliferation activity of the ADSC co-cultured with different scaffold materials was as follows: polycaprolactone/β-tricalcium phosphate/0.2% carbon nanotube scaffolds > polycaprolactone/β-tricalcium phosphate/0.1% carbon nanotube scaffolds > polycaprolactone/β-tricalcium phosphate/0.3% carbon nanotube scaffolds > polycaprolactone/β-tricalcium phosphate scaffolds (P < 0.05). The results showed that polycaprolactone/β-tricalcium phosphate/0.2% carbon nanotube scaffolds promoted the adhesion and proliferation of ADSC. The combination of 3D printing technology and CAD software can be used to print personalized composite stents, which have the characteristics of repeatability, high precision, and low cost. Through 3D printing technology, combining a variety of materials with each other can provide the greatest advantages of materials. The waste of resources was avoided. The prepared polycaprolactone/β-tri-calcium phosphate/0.2% carbon nanotube scaffold has a good pore structure and mechanical properties that mimic human cancellous bone, is non-toxic and non-hemolytic, and is effective in promoting ADSC proliferation in vitro. Given this correspondence, 3D printed scaffold shows good biocompatibility and strength, and the fabrication method provides a proof of concept for developing scaffolds for bone tissue engineering applications.

3D-printed PCL/β-TCP/CS composite artificial bone and histocompatibility study

3D-Printed Bioceramic Scaffolds with High Strength and High Precision

3D printing of PCL-ceramic composite scaffolds for bone tissue engineering applications

Biocompatibility and biodegradation studies of PCL/β-TCP bone tissue scaffold fabricated by structural porogen method

3D Printed PCL/SrHA Scaffold for Enhanced Bone Regeneration

Biocompatibility And Biodegradation Studies Of Pcl/Beta-Tcp Bone Tissue Scaffold Fabricated By Structural Porogen Method

3D-Printed Scaffolds of Mesoporous Bioglass/gliadin/polycaprolactone Ternary Composite for Enhancement of Compressive Strength, Degradability, Cell Responses and New Bone Tissue Ingrowth

A Composite Lactide-Mineral 3D-Printed Scaffold for Bone Repair and Regeneration

3D Printed Multi-Functional Scaffolds Based on Poly(ε-Caprolactone) and Hydroxyapatite Composites

Fabrication and Biological Activity of 3D-Printed Polycaprolactone/Magnesium Porous Scaffolds for Critical Size Bone Defect Repair.

Fabrication and characterization of 3D printed biocomposite scaffolds based on PCL and zirconia nanoparticles

Study on the fabrication and performance of hierarchical porous 3D printed PCL-based artificial bone scaffold with anti-bacterial effect

3D printed polycaprolactone/β-tricalcium phosphate/carbon nanotube composite - Physical properties and biocompatibility

Biodegradable 3D Printed Scaffolds of Modified Poly (Trimethylene Carbonate) Composite Materials with Poly (L-Lactic Acid) and Hydroxyapatite for Bone Regeneration

Fused Deposition Modeling Printed PLA/Nano β-TCP Composite Bone Tissue Engineering Scaffolds for Promoting Osteogenic Induction Function

Fabrication of 3D Bioprinted Bi-Phasic Scaffold for Bone–Cartilage Interface Regeneration

3D-Printed composite scaffolds based on poly(ε-caprolactone) filled with poly(glutamic acid)-modified cellulose nanocrystals for improved bone tissue regeneration

Three dimensional printed macroporous polylactic acid/hydroxyapatite composite scaffolds for promoting bone formation in a critical-size rat calvarial defect model

3D PCL/fish collagen composite scaffolds incorporating osteogenic abalone protein hydrolysates for bone regeneration application: in vitro and in vivo studies

3D Printed Polycaprolactone/Gelatin/Bacterial Cellulose/Hydroxyapatite Composite Scaffold for Bone Tissue Engineering

The Enhanced Osteogenesis and Osteointegration of 3-DP PCL Scaffolds Via Structural and Functional Optimization Using Collagen Networks.