[Juvenile polyposis coli--a case report (author's transl)].

S. Sato,T. Hirasawa,H. Imai,M. Tashiro,M. Numasawa,H. Wakasa

1978-04-01

Abstract:

What problem does this paper attempt to address?

The application and mechanism of iron sulfides in arsenic removal from water and wastewater: A critical review

Xingfei Zhang,Huan Fan,Jia Yuan,Jia Tian,Yufeng Wang,Chenglong Lu,Haisheng Han,Wei Sun

DOI: https://doi.org/10.1016/j.jece.2022.108856

IF: 7.7

2022-12-01

Journal of Environmental Chemical Engineering

Abstract:Over the last decades, a large amount of arsenic-containing wastewater discharged by industries has seriously polluted groundwater and drinking water, resulting in the number of arsenicosis patients increasing day by day. Iron sulfides are considered promising for effective arsenic removal from water/wastewater due to their exclusive physical and chemical properties. The applications of various iron sulfides materials, including natural pyrite and pyrrhotite, modified pyrite, nanostructure FeS and FeS2, in arsenic removal from aqueous solution are summarized. The present review paper mainly analyzes the performance and influencing factors of iron sulfides in arsenic removal, the synthetic conditions of nanoparticles, and their limitations. pH and temperature are the two main factors affecting the removal efficiency of arsenic in low arsenic-containing water. It is necessary to modify natural iron sulfide or synthesize FeS, which will significantly enhance the reactivity of iron sulfides in high concentration arsenic-containing wastewater. The mechanisms behind the arsenite and arsenate removal by iron sulfides are discussed in detail. Adsorption and precipitation are the primary removal mechanisms of low concentration and high concentration arsenic-containing wastewater, respectively. Future needs in arsenic removal technology using iron sulfides are also proposed. Overall, iron sulfides offer considerable potential towards powerfully removing arsenic in both low and high concentrations of water/wastewater.

engineering, chemical, environmental
Experimental Study on Separation of Iron and Arsenic from Copper Sulfate Solution

Weisong Cai,Xiaohua Yu,Yan Lin,Qingfeng Shen,Yiming Zhu,Hongkun Dai,Yonggang Li

DOI: https://doi.org/10.1007/s11837-024-06614-2

2024-06-13

JOM

Abstract:A certain quantity of iron was present in the waste acid leach copper smelting dust, which affects the quality of the copper and current efficiency. Elimination of iron and arsenic, the effects of various temperatures, times, H 2 O 2 dosage, and initial pH were researched. The experimental findings indicated that the ideal conditions were 80°C, 3 h, hydrogen peroxide 6.5 times the dose of Fe 2+ in the theoretical oxidizing solution, and initial pH of 4. Arsenic removal rate was 99.5%, while iron removal rate could be 98.99%. The solution's iron concentration and arsenic concentration were both < 0.01 g/L under ideal circumstances. In addition, the morphology of the substances or elements involved in the precipitation of iron and arsenic was examined using XRD and thermodynamic studies, and the morphology of the precipitated slag was examined using SEM-EDS. These results show that hydrogen peroxide succeeded in removing arsenic and iron from the copper sulfate solution, and a pure copper sulfate solution was obtained.

materials science, multidisciplinary,metallurgy & metallurgical engineering,mineralogy,mining & mineral processing
Mechanistic insights into the structure-activity relationship of FeS for arsenic removal in strongly acidic wastewater

Xingfei Zhang,Jia Tian,Haisheng Han,Wei Sun,Yue Yang,Xiaoyun Jiang,Yang Cao

DOI: https://doi.org/10.1016/j.jwpe.2023.103904

IF: 7

2023-07-01

Journal of Water Process Engineering

Abstract:Sulfide precipitation is an efficient method for separation. However, its application is limited due to the significant H2S pollution caused by conventional reagents. The utilization of amorphous FeS lead to a substantial reduction in H2S escape, while concurrently enhancing the crystallization and settling characteristics of As-precipitates. Under the conditions of an initial arsenic and H2SO4 concentration in the solution of 2 g/L and 50 g/L, respectively, and a FeS dosage of 1.5 times the molar amount of S/As, the arsenic removal exhibited a significant decrease from 89.8 % to 40.8 % over a FeS aging period of 0 to 84 days. Notably, no H2S emissions were detected during the entire reaction process. XRD analysis revealed a transformation of FeS from its amorphous form to a crystalline state as it undergoes aging. This transition is primarily characterized by a reduction in interlayer spacing and FeS bond length within the FeS lattice. The lattice energy experienced a decrease from −3071 to −3688 kJ/mol, indicating the progressive stabilization of the FeS structure. FTIR and TG-DSC analyses have demonstrated the infiltration of water molecules into both the interlamellar spaces and the lattice of FeS during the process of crystallization. Additionally, As3+ ions were observed to initially adsorb onto the surface of aged FeS through the hydroxyl group, followed by their diffusion into the lattice. The products of arsenic removal undergone a transformation from As2S3 to predominantly FeAsS-like complexes, as the mechanism of arsenic removal shifted from precipitate transformation to adsorption and co-precipitation.

engineering, chemical, environmental,water resources
Study on the mechanism of copper and arsenic separation in copper smelting acidic solution by arsenic sulfide residue

Jiarun Zhang,Zhihong Liu,Zhiyong Liu

DOI: https://doi.org/10.1016/j.seppur.2024.129132

IF: 8.6

2024-08-19

Separation and Purification Technology

Abstract:A large amount of acidic solution containing arsenic and copper is produced in the hydrometallurgical treatment process of arsenic-containing solid waste in copper smelting. It is necessary to develop an economical and efficient separation technology of arsenic and copper from the solution. In this paper, according to the difference of solubility product between As 2 S 3 and CuS, arsenic sulfide residue (ASR) was used as copper precipitant to realize the efficient separation of copper and arsenic in acidic solution, so as to achieve the purpose of "treating waste with waste". It is found that the copper precipitation reaction is a more sensitive reaction. With the increase of temperature and time, the precipitation efficiency of copper first increases and then decreases, mainly because CuS will react with AsO 4 3- in the solution, and then re-dissolution occurs. With the increase of pH value, As and Fe precipitate, resulting in incomplete separation of Cu and As. Under the optimum conditions, the precipitation efficiencies of Cu, Sb, Cd, Fe and Zn reached 97.39 %, 46.31 %, 2.04 %, 2.59 % and 0.65 %, respectively. The content of Cu in the precipitated residue reaches 50.47 wt%. The precipitated residue can be used as raw material for copper smelting.

engineering, chemical
Transformation of Arsenic During Realgar Tailings Stabilization Using Ferrous Sulfate in a Pilot-Scale Treatment.

Xin Wang,He Zhang,Linling Wang,Jing Chen,Shiqi Xu,Huijie Hou,Yao Shi,Jingdong Zhang,Miao Ma,Daniel C. W. Tsang,John C. Crittenden

DOI: https://doi.org/10.1016/j.scitotenv.2019.02.289

IF: 9.8

2019-01-01

The Science of The Total Environment

Abstract:Massive realgar tailings abandoned in mining areas in China have caused serious arsenic (As) pollution seeking for urgent disposal. Stabilization treatment is a feasible strategy, however, stabilization technologies for realgar tailings, that arc Fe-deficient, Ca-rich and S-rich, have not been well developed to date. In this study, we conducted a pilot-scale stabilization treatment of realgar tailings via ferrous sulfate addition to evaluate the transformation of As during stabilization. We found that Si, As, Ca, and S were the predominant elements in the raw realgar tailings with a low content of Fe, and realgar ((As4S4)-S-II) and pharmacolite (CaElAs(V)O(4).2H(2)O) were the main As-bearing minerals. After the ferrous sulfate treatment, the As leaching concentration of realgar tailings was successfully reduced from 135 mg/L, to a level below the Chinese regulatory limit (2.5 mg/L). Based on the results of leaching tests, sequential extraction analysis, XRD, SEM-EDS, XPS, and thermodynamic modeling, we concluded that ferrous sulfate addition enhanced the transformation of Ca-As and S-As species to more stable Fe-As species, e.g., crystalline symplesite and amorphous Fe-As complex. Dissolution of pharmacolite was facilitated by H+ and SO42- derived from the hydrolysis and oxidation of ferrous sulfate, and oxidation of realgar could be promoted by reactive oxygen species (ROSS) from Fe(II) oxygenation. This study improved our understanding of As transformation pathways in realgar tailings during ferrous sulfate treatment, which could serve as an alternative scheme for realgar tailings stabilization. (C) 2019 Elsevier B.V. All rights reserved.
Repurposing of steel rolling sludge: Solvent-free preparation of α-Fe 2 O 3 nanoparticles and its application for As(III/V)-containing wastewater treatment

Zekun Zhao,Suqin Li,Yabin Zhang,Penghui Guo,Xin Zhao,Yongkui Li

DOI: https://doi.org/10.1016/j.jenvman.2023.118286

IF: 8.7

2023-06-03

Journal of Environmental Management

Abstract:Steel rolling sludge (SRS) is the by-product of metallurgical industry with abundant iron content, which needs to be utilized for producing high value-added products. Herein, cost-effective and highly adsorbent α-Fe 2 O 3 nanoparticles were prepared from SRS via a novel solvent-free method and applied to treat As(III/V)-containing wastewater. The structure of the prepared nanoparticles was observed to be spherical with a small crystal size (12.58 nm) and high specific surface area (145.03 m 2 /g). The nucleation mechanism of α-Fe 2 O 3 nanoparticles and the effect of crystal water were investigated. More importantly, compared with the traditional methods of preparation cost and yield, this study was found to have excellent economic benefits. The adsorption results indicated that the adsorbent could effectively remove arsenic over a wide pH range, and the optimal performance of nano adsorbent for As(III) and As(V) removal was observed at pH 4.0–9.0 and 2.0–4.0, respectively. The adsorption process was consistent with pseudo-second-order kinetic and Langmuir isothermal model. The maximum adsorption capacity (q m ) of adsorbent for As(III) and As(V) was 75.67 mg/g and 56.07 mg/g, respectively. Furthermore, α-Fe 2 O 3 nanoparticles exhibited great stability, and q m remained at 64.43 mg/g and 42.39 mg/g after five cycles. Particularly, the As(III) was removed by forming inner-sphere complexes with the adsorbent, and it partially oxidized to As(V) during this process. In contrast, the As(V) was removed by electrostatic adsorption and reaction with –OH on the adsorbent surface. Overall, resource utilization of SRS and the treatment of As(III)/(V)-containing wastewater in this study are in line with the current developments in the environmental and waste-to-value research.

environmental sciences
Effective removal of arsenide from aqueous solutions using mesoporous CoFe2O4/graphene oxide nanocomposites assisted by artificial intelligence

Xianliang Wu,Jiwei Hu,Xingfu Wang,Ling Xin,Caifang Li,Xionghui Wei

DOI: https://doi.org/10.1007/s42823-021-00239-0

2021-03-22

Carbon letters

Abstract:This study investigated the arsenide removal by using mesoporous CoFe2O4/graphene oxide nanocomposites based on batch experiments optimized by artificial intelligence tools. These nanocomposites were prepared by immobilizing cobalt ferrite on graphene oxide and then characterized using various techniques, including small angle X-ray diffraction, high-resolution transmission electron microscopy and energy-dispersive X-ray spectroscopy. Artificial intelligence tools associated with response surface methodology were employed to optimize the conditions of the arsenide removal process. The results showed that back propagation neural network combined with genetic algorithm was suitable for the arsenide removal from aqueous solutions by the nanocomposites based on the minimum average values of absolute errors and the value of R2. The optimal values of the four variables (operating temperature, initial pH, initial arsenide concentration, and contact time) were found to be 25.66 °C, 7.58, 10.78 mg/L and 46.41 min, and the predicted arsenide removal percentage was 84.78%. The verification experiment showed that the arsenide removal percentage was 86.62%, which was close to the predicted value. Three evaluation methods (gradient boosted regression trees, Garson method and analysis of variance) all demonstrated that the temperature was the most important explanatory variable for the arsenide removal. In addition, the arsenide removal process can be depicted with pseudo-second-order kinetics model and Langmuir isotherm, respectively. The thermodynamics investigation disclosed that the adsorption process was of a spontaneously endothermic nature. In summary, this study showed that ANN-GA was an efficient and feasible method in determining the optimum conditions for arsenic removal by CoFe2O4/graphene oxide nanocomposites.

materials science, multidisciplinary,chemistry
Efficient recovery of copper resources from copper smelting waste acid based on Cu(II)/As(III) competitive sulfuration mechanism

Xiaolu Sun,Linhua Jiang,Ning Duan,Guangbin Zhu,Yanli Xu,Hao Jin,Yong Liu,Rong Zhang

DOI: https://doi.org/10.1016/j.jclepro.2024.141975

IF: 11.1

2024-04-08

Journal of Cleaner Production

Abstract:Currently, domestic and foreign copper smelting waste acid mainly employ sulfuration method to realize the separation of Cu(II) and As(III), facing the problem of unreasonable sulfidizing agent dosage and sulfidation time. If excessive sulfidizing agent dosage or overly long sulfidation time, it will lead to human health threat and large hazardous waste volume. If insufficient sulfidizing agent dosage or overly short sulfidation time, it will cause the waste of copper resources and substandard treatment solution. In this paper, the competitive sulfuration mechanism of Cu(II)/As(III) solution ( C (As(III)) = 10 g/L) with different Cu(II) concentrations is revealed, i.e., when C (Cu(II)) ≥7 g/L, the sulfidation sequence of Cu(II) and As(III) follows the solubility product constant (Ksp); when C (Cu(II)) ≤6 g/L, the precipitation process of Cu(II)/As(III) is dominated by the liquid-phase mass-transfer mechanism (ion diffusion). The sulfide precipitation of Cu(II)/As(III) is a co-deposition process. With the increase of sulfidizing agent dosage ( S/Cu ratio) and sulfidation time ( t ), the Cu(II) concentration gradually decreases to reach complete removal, while the further increase of S/Cu ratio and t leads to the decrease of copper content in the sulfide precipitates. Finally, the methods are demonstrated that detected accurately Cu(II) and As(III) concentrations in a rapid and non-destructive manner. This work not only provides a novel perspective on the efficient separation of Cu(II)/As(III) in copper smelting waste acid, but also opens a unique approach for direct and rapid detection of Cu(II)/As(III) concentration during the sulfuration process. Hence, this research is a guide for the regulating means ( S/Cu and t ) in the actual multi-step sulfuration process of copper smelting waste acid treatment and electrorefining solution purification.

environmental sciences,green & sustainable science & technology,engineering, environmental
Treatment of strongly acidic wastewater with high arsenic concentrations by ferrous sulfide (FeS): Inhibitive effects of S(0)-enriched surfaces

Ruiping Liu,Zhongchao Yang,Ziliang He,Liyuan Wu,Chengzhi Hu,Wenzhu Wu,Jiuhui Qu

DOI: https://doi.org/10.1016/j.cej.2016.05.109

IF: 15.1

2016-01-01

Chemical Engineering Journal

Abstract:•FeS shows higher removal efficiency towards As(III) than As(V).•In acidic solution FeS dissolve to S(-II) for As(V) reduction and As2S3 formation.•S(-II) react with As(V) to form S(0)-rich surface on FeS and inhibit As removal.•S(II)-rich surface inhibit FeS dissolution and arsenic removal.•As(V) reduction to As(III) by dosing Na2S prior to FeS improve As(V) removal.
In-situ production of iron flocculation and reactive oxygen species by electrochemically decomposing siderite: An innovative Fe-EC route to remove trivalent arsenic

Mengfei Chen,Huimin Hu,Min Chen,Chao Wang,Qian Wang,Chaocheng Zeng,Qing Shi,Weijie Song,Xuewei Li,Qiwu Zhang

DOI: https://doi.org/10.1016/j.jhazmat.2022.129884

IF: 13.6

2022-09-07

Journal of Hazardous Materials

Abstract:The removal of trivalent arsenic (As (III)) from water has received extensive attention from researchers. Iron electrocoagulation (Fe-EC) is an efficient technology for arsenic removal. However, electrode passivation hinders the development and application of Fe-EC. In this work, an innovative Fe-EC route was developed to remove As (III) through an electrochemical-siderite packed column (ESC). Ferrous ions were produced from siderite near the anode, and hydroxide was generated near the cathode during the electrochemical decomposition of siderite. As a result, an effect of Fe-EC-like was obtained. The results showed that an excellent removal performance of As (III) (>99%) was obtained by adjusting the parameters (As (III) concentration at 10 mg/L, pH at 7, Na 2 SO 4 at 10 mM and the hydraulic retention time at 30 min) and the oxidation rate of As (III) reached 84.12%. The mechanism analysis indicated that As (III) was oxidized to As (V) by the produced active oxide species and electrode, and then was removed by capturing on the iron oxide precipitates. As (III) was likely to be oxidized in two ways, one by the reactive oxygen species (possibly •OH, Fe(IV) and •O 2 - species), and another directly by the anode. The long-term effectiveness of arsenic removal demonstrated that ESC process based on the electrochemical-siderite packed column was an appropriate candidate for treating As (III) pollution.

environmental sciences,engineering, environmental
Co-treatment of copper smelting flue dust and arsenic sulfide residue by a pyrometallurgical approach for simultaneous removal and recovery of arsenic

Wenjuan Zhang,Jianyong Che,Peicheng Wen,Liu Xia,Baozhong Ma,Jun Chen,Chengyan Wang

DOI: https://doi.org/10.1016/j.jhazmat.2021.126149

2021-08-15

Abstract:As the typical hazardous arsenic pollutants, copper smelting flue dust (CSFD) and arsenic sulfide residue (ASR) are produced extensively during copper smelting process, which pose significant pressure on environmental protection and green development of the copper industry. This work proposed an economic, efficient, and applicable approach to treat waste with waste, in which the simultaneous removal and recovery of As from CSFD and ASR were realized by a roasting process, with adding sulfuric acid, at a relatively low temperature (300-350 ℃). The thermodynamic analysis and experiments confirmed that the main phases of As2S3 and S0 in the ASR were used as a reductant for reducing As(Ⅴ) in the CSFD, and the introduction of sulfuric acid favorably enhanced the thermodynamic driving force and greatly lowered the reaction temperature. The results indicated that removal and behavior of As were highly dependent on the mass ratio of ASR to CSFD, roasting temperature, and H2SO4 dosage. By regulating the parameters, the species As2S3, As2O5, and arsenate were all converted to volatile As2O3, which could be captured and deposited in cold water. In the optimized co-treatment, a satisfied As removal efficiency of 96.12% was achieved, while getting the 97.03% pure As2O3.
High-efficiency removal of As(III) from groundwater using siderite as the iron source in the electrocoagulation process

Haitao Yu,Junfeng Li,Wenying Qu,Wenhuai Wang,Jiankang Wang

DOI: https://doi.org/10.1039/d4ra02716g

IF: 4.036

2024-06-15

RSC Advances

Abstract:Electrocoagulation technology, due to its simplicity and ease of operation, is often considered for treating arsenic-contaminated groundwater. However, challenges such as anode wear have hindered its development and application. This study aims to develop a siderite-filled anode electrocoagulation system for efficient removal of As( III ) and investigate its effectiveness. The impact of operational parameters on the removal rate of As( III ) was analyzed through single-factor tests, and the stability and superiority of the device were evaluated. The response surface methodology was employed to analyze the interactions between various factors and determine the optimal operational parameters by integrating data from these tests. Under conditions where the removal rate of As reached 99.3 ± 0.37%, with an initial concentration of As( III ) at 400 μg L −1 , current intensity at 30 mA, initial solution pH value at 7, and Na 2 SO 4 concentration at 10 mM. The flocculant used was subjected to characterization analysis to examine its structure, morphology, and elemental composition under these optimal operational parameters. The oxidation pathway for As( III ) within this system relies on integrated results from direct electrolysis as well as ̇O 2 − , ̇OH, and Fe( IV ) mediated oxidation processes. The elimination of arsenic encompasses two fundamental mechanisms: firstly, the direct adsorption of As( III ) by highly adsorbent flocculants like γ-FeOOH and magnetite (Fe 3 O 4 ); secondly, the oxidation of As( III ) into As( V ), followed by its reaction with siderite or other compounds to generate a dual coordination complex or iron arsenate, thus expediting its eradication. The anodic electrocoagulation system employing siderite as a filler exhibits remarkable efficiency and cost-effectiveness, while ensuring exceptional stability, thereby providing robust theoretical underpinnings for the application of electrocoagulation technology in arsenic removal.

chemistry, multidisciplinary
Removal and immobilization of arsenic from copper smelting wastewater using copper slag by in situ encapsulation with silica gel

Yongkui Li,Xing Zhu,Xianjin Qi,Bo Shu,Xin Zhang,Kongzhai Li,Yonggang Wei,Hua Wang

DOI: https://doi.org/10.1016/j.cej.2020.124833

IF: 15.1

2020-08-01

Chemical Engineering Journal

Abstract:Ferric arsenate is an important arsenic-containing compound in the mining-impacted environment and hydrometallurgical tailings, especially in the disposal of smelting wastewater in nonferrous smelting industries. It acts as an intermediate for arsenic removal and immobilization in the disposal of arsenic-containing wastewater. However, amorphous ferric arsenate suffers from poor stability with a high arsenic leachability in the aqueous environment. In this study, we develop a new strategy to remove and immobilize arsenic from copper smelting wastewater using copper slag through an in situ encapsulation of ferric arsenate with silica gel. The strategy provides an inherent arsenic disposal solution for copper smelting processes, allowing the removal of arsenic in the form of environmentally friendly precipitates. The results show copper slag mainly composed of Fe2SiO4 and Fe3O4 can be dissolved in copper smelting wastewater containing high sulfuric acid and arsenic, providing abundant Fe3+ ions and silicates for the following arsenic precipitation. In the room-temperature solid-liquid reaction between copper slag and wastewater, the Fe-As co-precipitation and the in situ encapsulation results in an environmentally stable and core-shell structured precipitate consisting of an amorphous ferric arsenate core and a silica gel shell. Copper slag achieves an arsenic removal efficiency of 98.85% and an arsenic removal capacity of 66.86 mg/g in the disposal of smelting wastewater with an initial arsenic concentration of 8458 mg/L. The findings and proposed strategy demonstrates the potential for the efficient and affordable disposal of arsenic-containing wastewater.

engineering, chemical, environmental
Adsorption combined with superconducting high gradient magnetic separation technique used for removal of arsenic and antimony.

Zenglu Qi,Tista Prasai Joshi,Ruiping Liu,Yiran Li,Huijuan Liu,Jiuhui Qu

DOI: https://doi.org/10.1016/j.jhazmat.2017.09.007

IF: 13.6

2017-01-01

Journal of Hazardous Materials

Abstract:Manganese iron oxide (MnFe2O4), an excellent arsenic(As)/antimony(Sb) removal adsorbent, is greatly restricted for the solid-liquid separation. Through the application of superconducting high gradient magnetic separation (HGMS) technique, we herein constructed a facility for the in situ solid-liquid separation of micro-sized MnFe2O4 adsorbent in As/Sb removal process. To the relative low initial concentration 50.0μgL-1, MnFe2O4 material sorbent can still decrease As or Sb below US EPA's drinking water standard limit. The separation of MnFe2O4 was mainly relied on the flow rate and the amount of steel wools in the HGMS system. At a flow rate 1Lmin-1 and 5% steel wools filling rate, the removal efficacies of As and Sb in natural water with the system were achieved to be 94.6% and 76.8%, respectively. At the meantime, nearly 100% micro-sized MnFe2O4 solid in the continuous field was readily to be separated via HGMS system. In a combination with the experiment results and finite element simulation, the separation was seemed to be independent on the magnetic field intensity, and the maximum separation capacities in various conditions were well predicted using the Thomas model (R2=0.87-0.99).
FeOOH and nZVI combined with superconducting high gradient magnetic separation for the remediation of high-arsenic metallurgical wastewater

Yongkui Li,Suqin Li,Binbin Hu,Xin Zhao,Penghui Guo

DOI: https://doi.org/10.1016/j.seppur.2021.120372

IF: 8.6

2022-03-01

Separation and Purification Technology

Abstract:Metallurgical wastewater with high arsenic (As) concentration presents important challenges to human health and the environment because of its high toxicity and carcinogenicity. Iron (Fe)-based adsorbents can effectively detoxify low As-containing wastewater but are less helpful for high concentration of As and for solid–liquid separation. Herein, an advanced strategy is proposed to dispose high As wastewater using nano-zerovalent iron (nZVI) and ferric oxyhydroxide (FeOOH) combined with superconducting high gradient magnetic separation (HGMS) technology. The superconducting HGMS technology promoted the removal of As by nZVI and FeOOH via a magnetic flocculation reaction, while simultaneously separating reaction products adsorbed As from wastewater. Interestingly, nZVI could be corroded to release Fe(II) ions which then generated Fenton reaction under aerobic conditions, facilitating the oxidization of As(III)/Fe(II) to As(V)/Fe(III) ions. The Fe(II) and Fe(III) hydrolyzed in the form of hydroxy hydroxide and further generated the magnetic flocculates and coprecipitate. The results showed that 99.06% of As was successfully removed from wastewater with an initial As concentration of 5358 mg/L, at a dosage of 20 g/L, a magnetic field strength of 5 T, and a flow velocity of 500 mL/min. Compared with FeOOH, nZVI showed more favorable adaptability for lead smelting wastewater. Removal of As from wastewater by using nZVI combined with superconducting HGMS technology has a great potential to achieve industrial application for metallurgical heavy metal wastewater.

engineering, chemical
Heavy-metal resistant bio-hybrid with biogenic ferrous sulfide nanoparticles: pH-regulated self-assembly and wastewater treatment application

Xian-Zhong Fu,Jie Wu,Jie Li,Jian Ding,Shuo Cui,Xue-Meng Wang,Yun-Jie Wang,Hou-Qi Liu,Xin Deng,Dong-Feng Liu,Wen-Wei Li

DOI: https://doi.org/10.1016/j.jhazmat.2022.130667

IF: 13.6

2022-12-29

Journal of Hazardous Materials

Abstract:Self-assembled bio-hybrids with biogenic ferrous sulfide nanoparticles (bio-FeS) on the cell surface are attractive for reduction of toxic heavy metals due to higher activity than bare bacteria, but they still suffer from slow synthesis and regeneration of bio-FeS and bacterial activity decay for removal of high-concentration heavy metals. A further optimization of the bio-FeS synthesis process and properties is of vital importance to address this challenge. Herein, we present a simple pH-regulation strategy to enhance bio-FeS synthesis and elucidated the underlying regulatory mechanisms. Slightly raising the pH from 7.4 to 8.3 led to 1.5-fold higher sulfide generation rate due to upregulated expression of thiosulfate reduction-related genes, and triggered the formation of fine-sized bio-FeS (29.4 ± 6.1 nm). The resulting bio-hybrid exhibited significantly improved extracellular reduction activity and was successfully used for treatment of high-concentration chromium -containing wastewater (Cr(VI), 80 mg/L) at satisfactory efficiency and stability. Its feasibility for bio-augmented treatment of real Cr(VI)-rich electroplating wastewater was also demonstrated, showing no obvious activity decline during 7-day operation. Overall, our work provides new insights into the environmental-responses of bio-hybrid self-assembly process, and may have important implications for optimized application of bio-hybrid for wastewater treatment and environmental remediation.

environmental sciences,engineering, environmental
Modeling and prediction of copper removal from aqueous solutions by nZVI/rGO magnetic nanocomposites using ANN-GA and ANN-PSO

Mingyi Fan,Jiwei Hu,Rensheng Cao,Kangning Xiong,Xionghui Wei

DOI: https://doi.org/10.1038/s41598-017-18223-y

IF: 4.6

2017-01-01

Scientific Reports

Abstract:Reduced graphene oxide-supported nanoscale zero-valent iron (nZVI/rGO) magnetic nanocomposites were prepared and then applied in the Cu(II) removal from aqueous solutions. Scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and superconduction quantum interference device magnetometer were performed to characterize the nZVI/rGO nanocomposites. In order to reduce the number of experiments and the economic cost, response surface methodology (RSM) combined with artificial intelligence (AI) techniques, such as artificial neural network (ANN), genetic algorithm (GA) and particle swarm optimization (PSO), has been utilized as a major tool that can model and optimize the removal processes, because a tremendous advance has recently been made on AI that may result in extensive applications. Based on RSM, ANN-GA and ANN-PSO were employed to model the Cu(II) removal process and optimize the operating parameters, e.g., operating temperature, initial pH, initial concentration and contact time. The ANN-PSO model was proven to be an effective tool for modeling and optimizing the Cu(II) removal with a low absolute error and a high removal efficiency. Furthermore, the isotherm, kinetic, thermodynamic studies and the XPS analysis were performed to explore the mechanisms of Cu(II) removal process.
Ultrasonic-enhanced selective arsenic removal and sulfide conversion from iron slag

Yuefeng Chen,Guo Lin,Shixing Wang,Hongliang Liu,Likang Fu,Dawei Xiang,Manying Zhu

DOI: https://doi.org/10.1016/j.jclepro.2024.141885

IF: 11.1

2024-04-01

Journal of Cleaner Production

Abstract:There are numerous valuable metals and the hazardous element arsenic in the iron slag produced in the zinc hydrometallurgy. The arsenic must be removed for comprehensive recovery of valuable elements. Generally, the alkaline arsenic removal produces large amounts of iron hydroxide colloids and iron slag agglomeration. Here, ultrasonic enhancement of NaOH–Na2S system is proposed to selectively remove arsenic from iron slag. Ultrasound destroys the agglomeration and encapsulation of zinc-containing iron slag and promotes the liquid-solid interfacial reaction. The arsenic removal percentage is 92.24% under ultrasonic power of 400 W, which is 12.14% higher than the conventional alkaline arsenic removal. The apparent activation energy of ultrasonic-enhanced alkali leaching for arsenic removal is calculated to be only 8.84 kJ/mol by kinetic experiments. Diffusion is proved to be the limiting link in the ultrasonic-enhanced leaching process for arsenic removal. This study proves that ultrasonic-enhanced Na2S–NaOH system has a good prospect for selective removal of arsenic from iron slag.

environmental sciences,green & sustainable science & technology,engineering, environmental
Synergistic Process Using Fe Hydrolytic Flocs and Ultrafiltration Membrane for Enhanced Antimony(V) Removal

Baiwen Ma,Xing Wang,Ruiping Liu,William A. Jefferson,Huachun Lan,Huijuan Liu,Jiuhui Qu

DOI: https://doi.org/10.1016/j.memsci.2017.05.022

IF: 9.5

2017-01-01

Journal of Membrane Science

Abstract:Antimony (Sb) is harmful to human health, and Sb(V) is much more difficult to remove from water than other toxic elements such as arsenic (As). Theoretical studies have suggested that in situ flocs have stronger adsorption ability toward heavy metals than pre-made adsorbents. We believe that rational design of in situ flocs and the associated device structure will enable a floc-based device to be utilized in the removal of heavy metals. Based on this concept, we developed an integrated process taking advantage of the strong adsorption abilities of in-situ Al or Fe hydrolytic flocs and excellent separation properties of ultrafiltration (UF) membranes. We found that flocs could be well dispersed in a membrane tank with aeration from the bottom, and Fe-based flocs performed better in removing Sb(V) and alleviating membrane fouling than Al-based flocs. We also demonstrated that higher Sb (V) removal efficiency was induced with continuous injection, and lower solution pH. By controlling the aeration rate, injection frequency and the solution pH, membrane fouling was alleviated, especially under weakly acidic conditions. Additionally, owing to the higher rejection efficiency of the UF membrane, the effluent quality was improved, including the iron concentration, turbidity, and chromaticity. This innovative separation method shows promising potential for application in removing heavy metals in water treatment.
In situ mechanochemical activation of reduced iron powder for arsenic stabilization in high content arsenic sulfide sludge

Lei Ouyang,Lei Zeng,Yaqian Cui,Nan Wang,Lihua Zhu

DOI: https://doi.org/10.1016/j.seppur.2022.122218

IF: 8.6

2023-01-15

Separation and Purification Technology

Abstract:Arsenic sulfide slag (ASS) with high content of arsenic is a common industrial waste in nonferrous metal smelting. Because of the high potential of arsenic leaching under environmental conditions, it brings serious ecological threat during storage. Stabilization of the unstable arsenic in ASS is urgently needed for its safe disposal. Current stabilization methods such as hydrothermal treatment, stabilization/solidification, and thermal copolymerization still face challenges including high energy consumption, poor stabilize efficiency and large volume increase after treatment. Here we developed a mechanochemical strategy to stabilize the bleachable arsenic using reduced iron powder as stabilizer. The arsenic leaching concentration was decreased from 18484.9 mg /L to only 56.3 mg/L after treatment, achieving a stabilization efficiency of 99.7 %. The mechanism study proved that MC treatment triggered the corrosion of Fe powder and dissolution of As2O3 with the help of acidic water in the ASS. An integration of the rapid reduction and oxidation then happened for the soluble arsenic. The produced As(II) and As(V) reacted with sulfide and iron oxides, greatly reducing the arsenic leaching concentration. The BCR sequential extraction results further conformed most of the arsenics (83.7 %) in ASS were stabilization into the environmental stable residual fraction.

engineering, chemical

[Juvenile polyposis coli--a case report (author's transl)].

The application and mechanism of iron sulfides in arsenic removal from water and wastewater: A critical review

Experimental Study on Separation of Iron and Arsenic from Copper Sulfate Solution

Mechanistic insights into the structure-activity relationship of FeS for arsenic removal in strongly acidic wastewater

Study on the mechanism of copper and arsenic separation in copper smelting acidic solution by arsenic sulfide residue

Transformation of Arsenic During Realgar Tailings Stabilization Using Ferrous Sulfate in a Pilot-Scale Treatment.

Repurposing of steel rolling sludge: Solvent-free preparation of α-Fe 2 O 3 nanoparticles and its application for As(III/V)-containing wastewater treatment

Effective removal of arsenide from aqueous solutions using mesoporous CoFe2O4/graphene oxide nanocomposites assisted by artificial intelligence

Efficient recovery of copper resources from copper smelting waste acid based on Cu(II)/As(III) competitive sulfuration mechanism

Treatment of strongly acidic wastewater with high arsenic concentrations by ferrous sulfide (FeS): Inhibitive effects of S(0)-enriched surfaces

In-situ production of iron flocculation and reactive oxygen species by electrochemically decomposing siderite: An innovative Fe-EC route to remove trivalent arsenic

Co-treatment of copper smelting flue dust and arsenic sulfide residue by a pyrometallurgical approach for simultaneous removal and recovery of arsenic

High-efficiency removal of As(III) from groundwater using siderite as the iron source in the electrocoagulation process

Removal and immobilization of arsenic from copper smelting wastewater using copper slag by in situ encapsulation with silica gel

Adsorption combined with superconducting high gradient magnetic separation technique used for removal of arsenic and antimony.

FeOOH and nZVI combined with superconducting high gradient magnetic separation for the remediation of high-arsenic metallurgical wastewater

Heavy-metal resistant bio-hybrid with biogenic ferrous sulfide nanoparticles: pH-regulated self-assembly and wastewater treatment application

Modeling and prediction of copper removal from aqueous solutions by nZVI/rGO magnetic nanocomposites using ANN-GA and ANN-PSO

Ultrasonic-enhanced selective arsenic removal and sulfide conversion from iron slag

Synergistic Process Using Fe Hydrolytic Flocs and Ultrafiltration Membrane for Enhanced Antimony(V) Removal

In situ mechanochemical activation of reduced iron powder for arsenic stabilization in high content arsenic sulfide sludge