Abstract:Objective: To evaluate the effect of computer-assisted design based on three-dimensional reconstruction technique on the reduction accuracy of tibial and fibular fractures with Taylor external fixation. Methods: A retrospective review was conducted on the clinical data of 69 patients who had tibia and fibula fractures treated with Taylor external fixation in department of orthopedic trauma of Tianjin Hospital from January 2016 to January 2018 to compare the residual deformity after fracture reduction between computer-assisted design method (experimental group) and the standard measurement method (control group). The frontal and lateral tibia and fibula X-ray of all the affected limbs were taken. In experimental group, all the patients took bilateral tibial CT tomography, and then DICOM format documents were input into the Mimics 17.1 software and got three-dimensional models of targeted bone and external fixation ring. After that the visual image matching was performed between external fixation ring three-dimensional reconstruction model and the standard model and also between the affected limb and the contralateral limb. Then the reduction trajectory plan of bone broken end and the position of external fixation ring were obtained. The STL files were input to Solid Works software and got the length of six rods to adjust the Taylor external fixation. In control group, the films were measured by Coreldraw X7 X-ray measurement software and the parameters were input in Taylor Spatial Frame system software. And then six calibrated threaded rods were adjusted according to the prescription of the software. Finally, all the patients took the X-ray films again to evaluate the degree of residual displacement. Skew distributional data are indicated with M(QR), and method of non-parameter was used to analyze variances between groups. Results: All patients had better fracture reduction and achieved functional reset criteria. In the control group, the amount of displacement and angle residual aberration (improvement) in the frontal and lateral radiographs were 0.50(2.30)mm(90%), 0.00(0.85)mm(100%)and 0.00°(1.50°)(100%), 0.00°(0.00°)(100%), respectively. In the control group, the amount of displacement and angle residual aberration (improvement) in the frontal and lateral radiographs were 1.40(3.28)mm(69%), 2.15(4.27)mm(46%)and 1.15°(1.85°)(73%), 0.80°(2.10°)(67%). The positive and lateral angles and lateral displacements in the two groups were significantly different(P<0.05), but there was no statistically significant difference in positive displacement (P=0.099). Conclusion: Both computer-assisted design method and the standard measurement method have satisfactory reduction effect, but computer-assisted design can accurately correct fracture deformity, which is good for fracture healing and functional recovery of affected limb.

Study on orthopaedic path planning of Taylor spatial frame

Taylor spatial frame using for deformity correction around ankle

Investigation of Correction Trajectory Considering Bone End-Plane Orientation and the Shortest Growth Path

Clinical application of Taylor spatial frame in adjustment of lower extremity force line of knee medial compartmental osteoarthritis

Influence of Parameter Deviation on the Closeness of the Tibial Limb and External Fixator Based on a Novel Collision Detection Algorithm

Computer-aided adjustment of Taylor spatial frame for treatment of tibiofibular fracture

A Novel Computer-Assisted System for Long Bone Fracture Reduction with a Hexapod External Fixator

[The Application of Computer-Assisted Design in the Reduction of Long Bone Fractures with Taylor Spatial Frame].

Effect of two measurement methods on the accuracy of Taylor external fixator for fracture reduction

Configuration Design and Correction Ability Evaluation of a Novel External Fixator for Foot and Ankle Deformity Treated by U Osteotomy.

Computer hexapod assisted orthopaedic surgery (CHAOS) in the correction of long bone fracture and deformity

Comparison of Three Different Correction Trajectories for Foot and Ankle Deformity Treated by Supramalleolar Osteotomy Using a Novel External Fixator.

Opening Wedge High Tibial Osteotomy with Combined Use of Patient-Specific 3D-Printed Plates and Taylor Spatial Frame for the Treatment of Knee Osteoarthritis.

A 4-DOF Parallel External Fixator for Foot-Ankle Deformity Correction

Correction of Tibial Malunion and Nonunion With Six-Axis Analysis Deformity Correction Using the Taylor Spatial Frame

Design and Kinematics Analysis of Tibial Orthopedic External Fixation Robot Based on Bone External Fixation Technology

Structured Integration and Alignment Algorithm: A Tool for Personalized Surgical Treatment of Tibial Plateau Fractures

Surgical planning in HTO – alternative approaches to the Fujisawa gold-standard

Limb lengthening and deformity correction of congenital and acquired deformities in children using the Taylor Spatial Frame

Preoperative trajectory planning for closed reduction of long-bone diaphyseal fracture using a computer-assisted reduction system

A novel combination of computer-assisted reduction technique and three dimensional printed patient-specific external fixator for treatment of tibial fractures