Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Cross-interface computed tomography applied in flame propagation detection of an optical engine

An Experimental Investigation of Early Flame Development in an Optical Spark Ignition Engine Fueled with Natural Gas

Observation of Flame Propagation in a Heavy-Duty Natural-Gas Lean Burn Spark-Ignition Engine

Three-dimensional inhomogeneous temperature tomography of confined-space flame coupled with wall radiation effect by instantaneous light field

Computed Tomography Measurement of 3D Combustion Chemiluminescence Using Single Camera

Sensing flame structure by process tomography

Research on the Application of Combustion Optical Visualization Technology in the Test of Internal Combustion Engine

Characterization of In-Cylinder Combustion Temperature Based on a Flame-Image Processing Technique

Studies On Gas Concentration Reconstruction Methods For Simultaneous Temperature And H2o Concentration Tomographic Imaging In A Flame Based On Tunable Diode Laser Absorption Spectroscopy

An experimental study of the detailed flame transport in a SI engine using simultaneous dual-plane OH-LIF and stereoscopic PIV

Investigation of the Ignition Processes of a Multi-Injection Flame in a Diesel Engine Environment Using the Flamelet Model.

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

An Optical Study of In-Cylinder CH2O and OH Chemiluminescence in Flame-Induced Reaction Front Propagation Using High Speed Imaging

Application of UVAS and TDLAS-based multi-combustion-parameter diagnosis using computerized tomography

Research on Combustion Flow Field Imaging Method Based on Ray Casting Algorithm

High spatial resolution computed tomography of chemiluminescence with densely sampled parallel projections

Three-dimensional rapid visualization of flame temperature field via compression and noise reduction of light field imaging

Research Progress of Laser-induced Fluorescence in Combustion Visualization of Internal Combustion Engine

Optimization Design of Laser Arrays Based on Absorption Spectroscopy Imaging for Detecting Temperature and Concentration Fields

Advanced Image Processing Techniques for Multi-Level Characterization of Significant Flame Features in Carbon-Neutral Combustion

Flame/flow dynamics at the piston surface of an IC engine measured by high-speed PLIF and PTV