Abstract:Abstract Metal-composite laminates and joints are applied in aircraft manufacturing and maintenance (repairing) using aluminum alloys (AA) and glass fiber-reinforced polymer (GFRP). In these applications, drilling has a prominent place due to its vast application in aeronautical structures’ mechanical joints. Thus, this study presents the influence of uncoated carbide drills (85C, 86C, H10N), cutting speeds ( v c = 20, 40, and 60 m min −1 ), and feed rates ( f = 0.05, 0.15, and 0.25 mm rev −1 ) on delamination factor, thrust force ( F t {F}_{\text{t}} ), and burr formation in dry drilling metal-composite laminates and joints (AA2024/GFRP/AA2024). Experiments were performed, analyzed, and optimized using the Box–Behnken statistical design. Microscopic digital images for delamination evaluation, piezoelectric dynamometer for thrust force acquisition, and burr analysis were considered. The major finding was that the thrust force during drilling depends significantly on the feed rate. Another significant factor was the influence of the drill type (combined or not with feed rate). In fact, it was verified that the feed rate and the drill type were the most significant parameters on the delamination factor, while the feed rate was the most relevant on thrust force. The cutting speed did not affect significantly thrust force and delamination factor at exit ( F da S ) \hspace{.25em}({F}_{{\text{da}}_{\text{S}}}) . However, the combination f × v c was significant in delamination factor at entrance ( F da E ) \text{ }({F}_{{\text{da}}_{\text{E}}}) . Based on the optimized input parameters, they presented lower values for delamination factors ( F da E = 1.18 {F}_{{\text{da}}_{\text{E}}}=1.18 and F da S = 1.33 {F}_{{\text{da}}_{\text{S}}}=\hspace{.25em}1.33 ) and thrust force ( F t = 67.3 N {F}_{\text{t}}=67.3\hspace{.5em}\text{N} ). These values were obtained by drilling the metal-composite laminates with 85C-tool, 0.05 mm rev −1 feed rate, and 20 m min −1 cutting speed. However, the burrs at the hole output of AA2024 were considered unsatisfactory for this specific condition, which implies additional investigation.

A hybrid GRA-PCA-TOPSIS Technique Optimization of EDD Process Parameter on Drilling of AL8011/B4C/aloevera composites

Investigation on Electrical Discharge Machining Parameters of Aluminium7075/Boron Carbide/Titanium Diboride Hybrid Composites by Grey Relational Analysis

Optimizing the Drilling process parameters of AZ91 based hybrid composites using TOPSIS and Grey Relational Analysis

Near Dry Powder Mixed Electric Discharge Machining of AA7050 Hybrid Composites Utilizing Composite Tool Materials

An investigation on the effect of alumina nano powder mixed dielectric oil on EDM-assisted precision micro-drilling operation

Process parameters optimization of EDM for hybrid aluminum MMC using hybrid optimization technique

Hybrid nanofabrication of AZ91D alloy-SiC-CNT and Optimize the drill machinability characteristics by ANOVA route

A Hybrid Design of Experiment Approach in Analyzing the Electrical Discharge Machining Influence on Stir Cast Al7075/B4C Metal Matrix Composites

Optimization by AHP-ARAS of EDM Process Parameters on Machining AA7050-10%B4C Composite

WEDM of Al/SiC/Ti composite: A Hybrid Approach of RSM-ARAS-TLBO Algorithm

CFRP composite drilling through electrical discharge machining using aluminum as fixture plate

Performance analysis of powder-assisted micro-drilling operation using micro-EDM

Multi-objective Optimization of Electric Discharge Machining of Al-SiCp Composite by Taguchi-PCA, Firefly and Cuckoo Search Algorithm

Electric Discharge Machining of AA7075/SiCP/B4CP Hybrid Composites machined with Al2O3 Mixed Used Engine Oil Dielectric fluid

Optimization of Process Variables in the Drilling of LM6/B4C Composites through Grey Relational Analysis

Drilling performance analysis on super duplex stainless steel (AISI 2507) using scalable pulse power plasma TiSiN- and AlTiN-coated tools and optimizing machining parameters through Taguchi–Fuzzy approach

Application of the central composite design in optimization of machining parameters in drilling hybrid metal matrix composites

Optimization for drilling process of metal-composite aeronautical structures

Synthesis of Stir-Cast AA7050/5%B4C Composite and Optimization of EDM Response Parameters Using Taguchi Analysis

Parametric assessment of electrical discharge drilling on plasma sprayed functionally graded Al/Al 2 O 3 coating on Al6061-T6 faceplates

Parametric optimisation of milling process for the machining of carbon nanotubes-based hybrid aluminium composite