Application of fuzzy measures in the product appearance value assessment

Ling-Zhong Lin,T. Hsu,Liang-Chih Huang

DOI: https://doi.org/10.1016/j.asoc.2010.06.001

IF: 8.7

2011-03-01

Applied Soft Computing

Abstract:

What problem does this paper attempt to address?

Dimethyl Sulfoxide Mediated High-Fidelity 3D Printing of Hydrogels

Yixian Wang,Xin Xu,Desheng Liu,Jiayu Wu,Xingxing Yang,Bin Zhu,Chufeng Sun,Pan Jiang,Xiaolong Wang

DOI: https://doi.org/10.1016/j.addma.2024.104346

IF: 11

2024-01-01

Additive Manufacturing

Abstract:Owing to flexible structural design and rapid prototyping manufacturing, 3D printable hydrogels with solid-like and fluid-like characters have emerged as a promising candidate for biomedical engineering, soft robotics, and flexible electronics. However, existing 3D printing of hydrogel place substantial constraints on hydrogel high-fidelity of the printed hydrogel complex structures due to the shape deformation and collapse caused by water evaporation. Herein, we propose a mixed solvent printing strategy followed with water dialysis to achieve vat photopolymerization 3D printing of high-fidelity hydrogel structure by restraining water evaporation. Concretely, dimethyl sulfoxide (DMSO) is introduced into the hydrogel ink as co-solvent to improve the anti-dehydration performance during 3D printing. The as-prepared gels are then transformed into hydrogels with good fidelity and excellent performance through solvent exchange and water dialysis. Enabled by these characteristics, various functional devices with complex structures are demonstrated with the present high-fidelity 3D printing of diverse hydrogels. The solvent assisted high-fidelity hydrogel 3D printing protocol combining with the compatibility to various high-performance hydrogels is believed to be promising for wearable devices, wound dressings, electronic skin, and intelligent robots.
Fabrication of Liver Microtissue with Liver Decellularized Extracellular Matrix (decm) Bioink by Digital Light Processing (DLP) Bioprinting

Qijiang Mao,Yifan Wang,Yang Li,Sarun Juengpanich,Wenhuan Li,Mingyu Chen,Jun Yin,Jianzhong Fu,Xiujun Cai

DOI: https://doi.org/10.1016/j.msec.2020.110625

2020-01-01

Abstract:As one of the most effective treatments of end-stage liver disease, liver transplantation still suffers from a shortage of donor organs or a low degree of engraftment. Thus, alternatives to liver transplantation, such as liver support systems, have to be extensively explored. In this study, a novel liver microtissue with an inner gear-like structure, which achieved a larger body surface area, was designed and manufactured to improve hepatic functional restoration. The liver-specific bioinks were developed by combining photocurable methacrylated gelatin (GelMA) with liver decellularized extracellular matrix (dECM), and human-induced hepatocytes (hiHep cells) were encapsulated to form cell-laden bioinks. The mechanical properties, swelling, and cytocompatibility of GelMA/dECM bioinks were carefully characterized before 3D printing. Then, the digital light process (DLP)-based bioprinting was used to fabricate the liver microtissue, and liver dECM was found to improve both the printability and cell viability of GelMA bioinks. hiHep cells were also found to spread farther and have better hepatocyte-specific functions (albumin secretion and urea) in the liver microtissue when liver dECM was added to the GelMA bioinks. Our results provide a promising liver dECM-based cell-laden bioink for liver microtissue fabrication, which would be a potential liver tissue engineering product to help restore hepatic functions.
3D Bioprinting of Multi-Material Decellularized Liver Matrix Hydrogel at Physiological Temperatures

Vamakshi Khati,Harisha Ramachandraiah,Falguni Pati,Helene A Svahn,Giulia Gaudenzi,Aman Russom

DOI: https://doi.org/10.3390/bios12070521

2022-07-13

Abstract:Bioprinting is an acclaimed technique that allows the scaling of 3D architectures in an organized pattern but suffers from a scarcity of appropriate bioinks. Decellularized extracellular matrix (dECM) from xenogeneic species has garnered support as a biomaterial to promote tissue-specific regeneration and repair. The prospect of developing dECM-based 3D artificial tissue is impeded by its inherent low mechanical properties. In recent years, 3D bioprinting of dECM-based bioinks modified with additional scaffolds has advanced the development of load-bearing constructs. However, previous attempts using dECM were limited to low-temperature bioprinting, which is not favorable for a longer print duration with cells. Here, we report the development of a multi-material decellularized liver matrix (dLM) bioink reinforced with gelatin and polyethylene glycol to improve rheology, extrudability, and mechanical stability. This shear-thinning bioink facilitated extrusion-based bioprinting at 37 °C with HepG2 cells into a 3D grid structure with a further enhancement for long-term applications by enzymatic crosslinking with mushroom tyrosinase. The heavily crosslinked structure showed a 16-fold increase in viscosity (2.73 Pa s-1) and a 32-fold increase in storage modulus from the non-crosslinked dLM while retaining high cell viability (85-93%) and liver-specific functions. Our results show that the cytocompatible crosslinking of dLM bioink at physiological temperatures has promising applications for extended 3D-printing procedures.
3D bioprinting of Liver Microenvironment Model Using Photocrosslinkable Decellularized Extracellular Matrix based Hydrogel

Nima Tabatabaei Rezaei,Hitendra Kumar,Hongqun Liu,Ashna Rajeev,Giovanniantonio Natale,Samuel S. Lee,Simon S. Park,Keekyoung Kim

DOI: https://doi.org/10.1101/2024.04.17.589849

2024-04-20

Abstract:The liver, as one of the vital organs in the body, plays a crucial role in various bodily functions. Numerous factors can cause liver damage, that the sole remedy for severe liver conditions is the transplantation of healthy liver tissue. In response to the transplantation challenges, innovative approaches involving hydrogel-based technologies have emerged, leading to the creation of highly functionalized tissues. The development of three-dimensional printing and patterning of cell-laden biomaterial matrices offers promising advances for creating tissue-specific structures in tissue engineering and bioprinting. However, the matrix materials currently employed in bioprinting liver microtissue often fail to capture the complexity of the natural extracellular matrix (ECM), hindering their ability to restore innate cellular shapes and functions. Liver ECM-based hydrogels are increasingly recognized for their potential as biomimetic 3D cell culture systems that facilitate the exploration of liver disease, metabolism, and toxicity mechanisms. Yet, the conventional production of these hydrogels relies on slow thermal gelation processes, which restrict the manipulation of their mechanical characteristics. In this research, we introduce a novel approach with a functionalized photocrosslinkable liver decellularized extracellular matrix (dECM). By combining liver dECM methacrylate (LdECMMA) with gelatin methacrylate (GelMA), we achieved accelerated crosslinking under visible light irradiation and the ability to tune the mechanical, rheological, and physiological properties of the material. We encapsulated human hepatocellular carcinoma cells within an optimal concentration of the GelMA-LdECMMA hybrid hydrogel and examined cell proliferation and function over an extended period. The findings revealed that the GelMA-LdECMMA hybrid hydrogel enhances liver cell proliferation and function, holding significant promise for applications in drug screening and liver cancer metastasis research.

Bioengineering
Instant Gelation System As Self-Healable and Printable 3D Cell Culture Bioink Based on Dynamic Covalent Chemistry.

A. Sigen,Jing Lyu,Melissa Johnson,Jack Creagh-Flynn,Dezhong Zhou,Irene Lara-Saez,Qian Xu,Hongyun Tai,Wenxin Wang

DOI: https://doi.org/10.1021/acsami.0c08567

IF: 9.5

2020-01-01

ACS Applied Materials & Interfaces

Abstract:The rapid development of additive manufacturing techniques in the field of tissue regeneration offers unprecedented success for artificial tissue and organ fabrication. However, some limitations still remain for current bioinks, such as the compromised cell viability after printing, the low cross-linking efficiency leading to poor printing resolution and speed due to the relatively slow gelation rate, and the requirement of external stimuli for gelation. To address these problems, herein, a biocompatible and printable instant gelation hydrogel system has been developed based on a designed hyperbranched poly(ethylene glycol) (PEG)-based multihydrazide macro-cross-linker (HB-PEG-HDZ) and an aldehyde-functionalized hyaluronic acid (HA-CHO). HB-PEG-HDZ is prepared by the postfunctionalization of hyperbranched PEG-based multivinyl macromer via thiol-ene chemistry. Owing to the high functional group density of HB-PEG-HDZ, the hydrogel can be formed instantly upon mixing the solutions of two components. The reversible cross-linking mechanism between the hydrazide and aldehyde groups endows the hydrogel with shear-thinning and self-healing properties. The minimally toxic components and cross-linking chemistry allow the resulting hydrogel to be a biocompatible niche. Moreover, the fast sol-to-gel transition of the hydrogel, combining all of the advanced characteristics of this platform, protects the cells during the printing procedure, avoids their damage during extrusion, and improves the transplanted cell survival.
DEAE- Cellulose-based composite hydrogel for 3D printing application: Physicochemical, mechanical, and biological optimization

Rathina Vel,Anugya Bhatt,A. Priyanka,Ashna Gauthaman,V. Anilkumar,A.S. Safeena,S Ranjith,Ranjith S

DOI: https://doi.org/10.1016/j.mtcomm.2022.104335

IF: 3.8

2022-09-06

Materials Today Communications

Abstract:3D bioprinting is a layer-by-layer additive manufacturing process that requires the incorporation of biomaterials, cells, growth factors, etc. The biomaterial-ink used in bioprinting should comprise essential properties like shear thinning, proper viscosity and reduced shear stress on cells, structural integrity, porosity, biocompatible and degradable, etc., Especially in extrusion-based bioprinting, optimization of biomaterial ink is critical. Even though single-aspect biomaterials have been used for establishing a biomaterial ink, however, they often fail to meet all properties needed to be used as a biomaterial ink. Carrying this point in view, we have formulated hydrogels using Diethylaminoethyl Cellulose (DEAE-Cellulose), Alginate (ALG), and Gelatin (GEL) as biomaterial inks. Initially, six different hydrogel formulations (F1-F6) were prepared with varying concentrations of DEAE- Cellulose (0.45%−2%), alginate (1%−2%), and keeping gelatine concentration constant at 3.33%. These formulations were then assayed by swelling and degradation tests. Out of six, three hydrogels (F3, F4, and F5) were eliminated after initial studies due to the rapid degradation rate. The other three hydrogels ( F1, F2, and F6) were further thoroughly analyzed by the rheological study, mechanical study, printability assay, morphological analysis, and biocompatibility assays. Here, We have demonstrated the successful formulation of three biomaterial inks utilizing three different biopolymers for the field of tissue engineering with adequate swelling, degradation, rheological and printability properties. It was observed that the incorporation of DEAE-Cellulose significantly improved the shear thinning and viscosity recovery of hydrogels. Also, it improves mechanical integrity and printing accuracy. Moreover, all three hydrogels have shown excellent hemocompatibility and cytocompatibility. To conclude, this study proposes the optimization of composite hydrogel for 3D printing applications.

materials science, multidisciplinary
Double-Network Hydrogel 3D BioPrinting Biocompatible with Fibroblast Cells for Tissue Engineering Applications

Immacolata Greco,Hatim Machrafi,Carlo Iorio

DOI: https://doi.org/10.3390/gels10110684

IF: 4.6

2024-10-24

Gels

Abstract:The present study examines the formulation of a biocompatible hydrogel bioink for 3D bioprinting, integrating poly(ethylene glycol) diacrylate (PEGDA) and sodium alginate (SA) using a double-network approach. These materials were chosen for their synergistic qualities, with PEGDA contributing to mechanical integrity and SA ensuring biocompatibility. Fibroblast cells were included in the bioink and printed with a Reg4Life bioprinter employing micro-extrusion technology. The optimisation of printing parameters included needle size and flow velocities. This led to precise structure development and yielded results with a negligible deviation in printed angles and better control of line widths. The rheological characteristics of the bioink were evaluated, demonstrating appropriate viscosity and shear-thinning behaviour for efficient extrusion. The mechanical characterisation revealed an average compressive modulus of 0.38 MPa, suitable for tissue engineering applications. The printability of the bioink was further confirmed through the evaluations of morphology and diffusion rates, confirming structural integrity. Biocompatibility assessments demonstrated a high cell viability rate of 82.65% following 48 h of incubation, supporting the bioink's suitability for facilitating cell survival. This study introduced a reliable technique for producing tissue-engineered scaffolds that exhibit outstanding mechanical characteristics and cell viability, highlighting the promise of PEGDA–SA hydrogels in bioprinting applications.

polymer science
DLP 3D Printing Meets Lignocellulosic Biopolymers: Carboxymethyl Cellulose Inks for 3D Biocompatible Hydrogels

Giuseppe Melilli,Irene Carmagnola,Chiara Tonda-Turo,Fabrizio Pirri,Gianluca Ciardelli,Marco Sangermano,Minna Hakkarainen,Annalisa Chiappone

DOI: https://doi.org/10.3390/polym12081655

IF: 5

2020-07-25

Polymers

Abstract:The development of new bio-based inks is a stringent request for the expansion of additive manufacturing towards the development of 3D-printed biocompatible hydrogels. Herein, methacrylated carboxymethyl cellulose (M-CMC) is investigated as a bio-based photocurable ink for digital light processing (DLP) 3D printing. CMC is chemically modified using methacrylic anhydride. Successful methacrylation is confirmed by 1H NMR and FTIR spectroscopy. Aqueous formulations based on M-CMC/lithium phenyl-2,4,6-trimethylbenzoylphosphinate (LAP) photoinitiator and M-CMC/Dulbecco’s Modified Eagle Medium (DMEM)/LAP show high photoreactivity upon UV irradiation as confirmed by photorheology and FTIR. The same formulations can be easily 3D-printed through a DLP apparatus to produce 3D shaped hydrogels with excellent swelling ability and mechanical properties. Envisaging the application of the hydrogels in the biomedical field, cytotoxicity is also evaluated. The light-induced printing of cellulose-based hydrogels represents a significant step forward in the production of new DLP inks suitable for biomedical applications.

polymer science
A thermogelling organic-inorganic hybrid hydrogel with excellent printability, shape fidelity and cytocompatibility for 3D bioprinting

Chen Hu,Taufiq Ahmad,Malik Salman Haider,Lukas Hahn,Philipp Stahlhut,Jürgen Groll,Robert Luxenhofer

DOI: https://doi.org/10.1088/1758-5090/ac40ee

2022-01-24

Biofabrication

Abstract:Alginates are the most commonly used bioink in biofabrication, but their rheological profiles make it very challenging to perform real 3D printing. In this study, an advanced hybrid hydrogel ink was developed, a mixture of thermogelling diblock copolymer, alginate and clay i.e. Laponite XLG. The reversible thermogelling and shear thinning properties of the diblock copolymer in the ink system improves handling and 3D printability significantly. Various three-dimensional constructs, including suspended filaments, were printed successfully with high shape fidelity and excellent stackability. Subsequent ionic crosslinking of alginate fixates the printed scaffolds, while the diblock copolymer is washed out of the structure, acting as a fugitive material/porogen on the (macro)molecular level. Finally, cell-laden printing and culture over 21 d demonstrated good cytocompatibility and feasibility of the novel hybrid hydrogels for 3D bioprinting. We believe that the developed approach could be interesting for a wide range of bioprinting applications including tissue engineering and drug screening, potentially enabling also other biological bioinks such as collagen, hyaluronic acid, decellularized extracellular matrices or cellulose based bioinks.
Direct 3D Printed Biomimetic Scaffolds Based on Hydrogel Microparticles for Cell Spheroid Growth

Hua Zhang,Yang Cong,Amarachi Rosemary Osi,Yang Zhou,Fangcheng Huang,Remo P. Zaccaria,Jing Chen,Rong Wang,Jun Fu

DOI: https://doi.org/10.1002/adfm.201910573

IF: 19

2020-03-01

Advanced Functional Materials

Abstract:Biocompatible hydrogel inks with shear‐thinning, appropriate yield strength, and fast self‐healing are desired for 3D bioprinting. However, the lack of ideal 3D bioprinting inks with outstanding printability and high structural fidelity, as well as cell‐compatibility, has hindered the progress of extrusion‐based 3D bioprinting for tissue engineering. In this study, novel self‐healable pre‐cross‐linked hydrogel microparticles (pcHμPs) of chitosan methacrylate (CHMA) and polyvinyl alcohol (PVA) hybrid hydrogels are developed and used as bioinks for extrusion‐based 3D printing of scaffolds with high fidelity and biocompatibility. The pcHμPs display excellent shear thinning when injected through a syringe and subsequently self‐heal into gels as shear forces are removed. Numerical simulations indicate that the pcHμPs experience a plug flow in the nozzle with minimal disturbance, which favors a steady and continuous printing. Moreover, the pcHμPs show a self‐supportive yield strength (540 Pa), which is critical for the fidelity of printed constructs. A series of biomimetic constructs with very high aspect ratio and delicate fine structures are directly printed by using the pcHμP ink. The 3D printed scaffolds support the growth of bone‐marrow‐derived mesenchymal stem cells and formation of cell spheroids, which are most important for tissue engineering.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
3D-printed scaffolds for tissue engineering applications using thermosensitive hydrogels based on biopolymer blends

Ioanna Koumentakou,Anna Michopoulou,Michiel Jan Noordam,Zoi Terzopoulou,Dimitrios N. Bikiaris

DOI: https://doi.org/10.1007/s10853-024-09707-0

IF: 4.5

2024-05-15

Journal of Materials Science

Abstract:Three-dimensional (3D) printing is an emerging technology for the construction of complex 3D constructs used for tissue engineering applications. In this study, we are proposing the preparation of 3D printing hydrogel inks consisting of the synthetic polymers poly(caprolactone) and poly(lactic acid), the biopolymer chitosan, and naturally derived gelatin. In addition, pluronic F-127 was used to improve the miscibility between the hydrophobic and hydrophilic components due to its amphiphilic character, as well as for its good 3D printability. The printability of the hydrogel inks was optimized by varying the composition, the extrusion nozzle, and the temperature, while the integrity of the 3D scaffolds was secured via sol–gel transition. The produced hydrogels with PCL-pluronic-chitosan-gelatin/15-20-4-2 wt% (PC3.75-Pl5-CG) and PLA-pluronic-chitosan-gelatin/10-20-4-2 wt% (PL2.5-Pl5-CG) presented the best printability, producing smooth and uniform porous scaffolds. The prepared hydrogels were formed via the interactions between the polymers through hydrogen bonding. Additionally, the produced hydrogels exhibited temperature-dependent swelling behavior, and the scaffolds with PCL presented lower swelling capacity than the scaffolds with PLA. The produced scaffolds presented slower hydrolyzation rate in simulated body fluid (SBF) at 25 °C compared to 37 °C. Biological studies proved that the 3D-printed porous scaffolds were non-cytotoxic and promoted human adipose-derived mesenchymal stem cell adhesion.

materials science, multidisciplinary
Digital light processing-based bioprinting of microtissue hydrogel arrays using dextran-induced aqueous emulsion ink

Yue Xu,Xueyuan Liao,Zhengbi Liu,Lin Zhang

DOI: https://doi.org/10.1177/08839115241237327

2024-03-18

Journal of Bioactive and Compatible Polymers

Abstract:Journal of Bioactive and Compatible Polymers, Ahead of Print. As a microscale three-dimensional bionic model, a microtissue array is a promising method for disease modeling and drug screening. Digital light processing (DLP) 3D bio-printing technology with the capabilities of excellent printing speed and resolution shows great potential for fabricating microtissue arrays. However, the outcomes of the microtissue arrays using DLP are limited by the shortage of biomaterials. In this work, we prepare hydrogel microtissues by combining DLP printing technology with biphasic bio-ink consisting of gelatin methacrylate (GelMA) and dextran. GelMA/ dextran is mixed to form bio-inks with different volume ratios, which can achieve high-precision printing of various patterns. Due to the presence of dextran, the bio-inks form the internal porous structure of the hydrogel in the printed patterns. The pore size is related to the proportion of dextran in bio-inks, and the pore size of hydrogel becomes smaller with the increase of dextran ratio. In addition, the adipose-derived stem cells (ADSCs) cells encapsulated in the porous hydrogels can maintain a high survival rate of 98.01% after 3 days of culture, and the larger pore size in the hydrogels promotes cell migration. Combining the DLP printing system with the porous hydrogel allows multiple micro-size geometric pattern hydrogels to be printed simultaneously to form microtissue arrays. In this study, a new bio-ink suitable for microtissue arrays is proposed, and a simple, accurate, and high-throughput biological manufacturing method for microtissue arrays is developed, thus providing a valuable tool for drug screening and tissue engineering.

biotechnology & applied microbiology,materials science, biomaterials,polymer science
Mussel-Inspired Naturally Derived Double-Network Hydrogels and Their Application in 3D Printing: from Soft, Injectable Bioadhesives to Mechanically Strong Hydrogels.

Zhongwei Guo,Jingling Xia,Shengli Mi,Wei Sun

DOI: https://doi.org/10.1021/acsbiomaterials.9b01864

2020-01-01

ACS Biomaterials Science & Engineering

Abstract:As promising candidates for tissue engineering, hydrogels possess great potential, especially in bioadhesives and load-bearing tissue scaffolds. However, a strategy for synthesizing hydrogels that could achieve the above requirements remains a challenge. Here, a mussel-inspired naturally derived double-network (DN) hydrogel composed of a special combination of two well-characterized natural polymers, hyaluronic acid and alginate, is presented. The key features are its two-step synthesis strategy, which generates injectable and adhesive properties in the first step and then transforms into a DN hydrogel with high mechanical strength and good resilient properties. Based on this strategy, the DN hydrogel could be tamed into a self-supporting three-dimensional (3D) printable bioink. As a rheological modifier, alginate was used to lubricate the covalent cross-linking hydrogels for better extrusion performance. The incorporation of alginate also enhanced the mechanical performance of the soft covalent network by forming reversible alginate-Ca2+ ionic cross-links, which interpenetrate through the outer water-retention scaffold with delicate weblike structures. In vitro cell culture data indicated that our bioink formulation and printing strategy are compatible with human umbilical vein endothelial cells (HUVECs).
Investigation of the 3D Printability of Covalently Cross-Linked Polypeptide-Based Hydrogels

Johnel Giliomee,Lisa C du Toit,Bert Klumperman,Yahya E Choonara

DOI: https://doi.org/10.1021/acsomega.1c05873

IF: 4.1

2022-02-28

ACS Omega

Abstract:The 3D printability of poly(l-lysine-ran-l-alanine) and four-arm poly(ethylene glycol) (P(KA)/4-PEG) hydrogels as 3D biomaterial inks was investigated using two approaches to develop P(KA)/4-PEG into 3D biomaterial inks. Only the "composite microgel" inks were 3D printable. In this approach, P(KA)/4-PEG hydrogels were processed into microparticles and incorporated into a polymer solution to produce a composite microgel paste. Polymer solutions composed of either 4-arm PEG-acrylate (4-PEG-Ac), chitosan (CS), or poly(vinyl alcohol) (PVA) were used as the matrix material for the composite paste. The three respective composite microgel inks displayed good 3D printability in terms of extrudability, layer-stacking ability, solidification mechanism, and 3D print fidelity. The biocompatibility of P(KA)/4-PEG hydrogels was retained in the 3D printed scaffolds, and the biofunctionality of bioinert 4-PEG and PVA hydrogels was enhanced. CS-P(KA)/4-PEG inks demonstrated excellent 3D printability and proved highly successful in printing scaffolds with a narrow strand diameter (∼200 μm) and narrow strand spacing (∼500 μm) while the integrity of the vertical and horizontal pores was maintained. Using different needle IDs and strand spacing, certain physical properties of the hydrogels could be tuned, while the 3D printed porosity was kept constant. This included the surface area to volume ratio, the macropore sizes, and the mechanical properties. The scaffolds demonstrated adequate adhesion and spreading of NIH 3T3 fibroblasts seeded on the scaffold surfaces for 4 days. Consequently, the scaffolds were considered suitable for potential applications in wound healing, as well as other soft tissue engineering applications. Apart from the contribution to new 3D biomaterial inks, this work also presented a new and facile method of processing covalently cross-linked hydrogels into 3D printed scaffolds. This could potentially "unlock" the 3D printability of biofunctional hydrogels, which are generally excluded from 3D printing applications.
Optimization of collagen type I-hyaluronan hybrid bioink for 3D bioprinted liver microenvironments

Andrea Mazzocchi,Mahesh Devarasetty,Richard Huntwork,Shay Soker,Aleksander Skardal

DOI: https://doi.org/10.1088/1758-5090/aae543

2018-10-30

Biofabrication

Abstract:Current 3D printing of tissue is restricted by the use of biomaterials that do not recapitulate the native properties of the extracellular matrix (ECM). These restrictions have thus far prevented optimization of composition and structure of the in vivo tissue microenvironment. The artificial nature of currently used biomaterials affects cellular phenotype and function of the bioprinted tissues, and results in inaccurate modeling of disease and drug metabolism significantly. Collagen type I is the major structural component in the ECM, and is widely used as a 3D hydrogel, but is less applicable for 3D bioprinting due to low viscosity and slow polymerization. We have hypothesized that a combination of hyaluronic acid with collagen I yields a bioink with the properties required for extrusion bioprinting, while supporting native cell-matrix interactions and preservation of the native microenvironment properties. To test this hypothesis, we tested the viscoelastic properties of three bioink formulations -2:1, 3:1, and 4:1 collagen type I to hyaluronic acid, and examined cellular behavior in order to determine an optimal formulation that allows for bioprinting while supporting biological activity. We then employed this formulation to bioprint 3D liver tissue constructs containing primary human hepatocytes and liver stellate cells and tested the effects of acetaminophen, a common liver toxicant. Our results have shown that the combination of methacrylated collagen type I and thiolated hyaluronic acid yield a simple, printable bioink that allows for modulation that was directly related to stromal cell elongation. Further, the bioink adequately allowed for implementation as a support hydrogel for hepatocytes which were able to remain viable over two weeks and responded to drug treatment appropriately.

engineering, biomedical,materials science, biomaterials
A self-healing hydrogel and injectable cryogel of gelatin methacryloyl-polyurethane double network for 3D printing

Qian-Pu Cheng,Shan-Hui Hsu

DOI: https://doi.org/10.1016/j.actbio.2023.04.023

2023-07-01

Abstract:Three-dimensional (3D) printing of soft biomaterials facilitates the progress of personalized medicine. The development for different forms of 3D-printable biomaterials can promotes the potential manufacturing for artificial organs and provides biomaterials with the required properties. In this study, gelatin methacryloyl (GelMA) and dialdehyde-functionalized polyurethane (DFPU) were combined to create a double crosslinking system and develop 3D-printable GelMA-PU biodegradable hydrogel and cryogel. The GelMA-PU system demonstrates a combination of self-healing ability and 3D printability and provides two distinct forms of 3D-printable biomaterials with smart functions, high printing resolution, and biocompatibility. The hydrogel was printed into individual modules through an 80 µm or larger nozzle and further assembled into complex structures through adhesive and self-healing abilities, which could be stabilized by secondary photocrosslinking. The 3D-printed hydrogel was adhesive, light transmittable, and could embed a light emitting diode (LED). Furthermore, the hydrogel laden with human mesenchymal stem cells (hMSCs) was successfully printed and showed cell proliferation. Meanwhile, 3D-printed cryogel was achieved by printing on a subzero temperature platform through a 210 µm nozzle. After secondary photocrosslinking and drying, the cryogel was deliverable through a 16-gage (1194 µm) syringe needle and can promote the proliferation of hMSCs. The GelMA-PU system extends the ink pool for 3D printing of biomaterials and has potential applications in tissue engineering scaffolds, minimally invasive surgery devices, and electronic wound dressings. STATEMENT OF SIGNIFICANCE: The 3D-printable biomaterials developed in this work are GelMA-based ink with smart funcitons and have potentials for various customized medical applications. The synthesized GelMA-polyurethane double network hydrogel can be 3D-printed into individual modules (e.g., 11 × 11 × 5 mm3) through an 80 μm or larger size nozzle, which are then assembled into a taller structure over five times of the initial height by self-healing and secondary photocrosslinking. The hydrogel is adhesive, light transmittable, and biocompatible that can either carry human mesenchymal stem cells (hMSCs) as bioink or embed a red light LED (620 nm) with potential applications in electronic skin dressing. Meanwhile, the 3D-printed highly compressible cryogel (e.g., 6 × 6 × 1 mm3) is deliverable by a 16-gage (1194 μm) syringe needle and supports the proliferation of hMSCs also.
Lubricating Micro‐Interface Assisted General Strategy for Preparing dECM‐Microparticle–Based Heterogeneous Granular Inks toward 3D Printing

Kunxi Zhang,Yinan Zhu,Tao Wang,Dawei Niu,Zijie Xiahou,Hongzhong Wang,Peiliang Fu,Haiyan Cui,Jingbo Yin

DOI: https://doi.org/10.1002/adfm.202307886

IF: 19

2023-12-12

Advanced Functional Materials

Abstract:Inspired by granular lubrication and joint lubrication, granular inks assembled from polydopamine‐based coating modified decellularized extracellular matrix‐microparticles (dECM‐MPs) and gelatin methacryloyl‐based microspheres are prepared and exhibit well‐performed extrudability, plasticity, and fidelity, realizing the printability of rigid dECM‐MPs at high content. Decellularized extracellular matrix (dECM) retains the bioactive components to mimic tissue‐specific microenvironment. Designing dECM‐based inks for 3D printing to prepare scaffolds can enhance the regeneration of corresponding tissues. However, due to the strict requirements for inks, how to efficiently prepare dECM‐based inks is a challenge. Inspired by granular lubrication, the present study proposes an effective and general method for preparing granular ink from dECM microparticles (MP) with high content. Through dopamine polymerization, dECM‐MPs are coated with polydopamine (PDA). Meanwhile, gelatin methacryloyl (GelMA)‐based microspheres (GelMA‐MSs) are prepared with available double bonds. dECM‐MPs (30–40 wt%) and GelMA‐MSs assemble to form a granular ink, exhibiting well‐performed extrudability, plasticity, and fidelity. Further inspired by joint lubrication, hyaluronic acid (HA) is introduced into PDA coating and GelMA‐MSs to reduce the micro‐interface friction, further promoting the printability and broadening the printable window of dECM‐MPs content to 30–60 wt%. Osteochondral scaffold and skin wound dressing are fabricated through 3D printing from the corresponding dECM‐MPs, enhancing the regeneration of the corresponding tissues in vivo. Especially, the realization of printability of highly rigid dECM‐MPs confirms the universality, reliability and efficiency of the present strategy.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Chemistry matters: A side-by-side comparison of two chemically distinct methacryloylated dECM bioresins for vat photopolymerization

Ahed Almalla,Laura Elomaa,Nora Fribiczer,Timm Landes,Peng Tang,Zeinab Mahfouz,Beate Koksch,Karl Herbert Hillebrandt,Igor Maximilian Sauer,Dag Heinemann,Sebastian Seiffert,Marie Weinhart

DOI: https://doi.org/10.1016/j.bioadv.2024.213850

Abstract:Decellularized extracellular matrix (dECM) is an excellent natural source for 3D bioprinting materials due to its inherent cell compatibility. In vat photopolymerization, the use of dECM-based bioresins is just emerging, and extensive research is needed to fully exploit their potential. In this study, two distinct methacryloyl-functionalized, photocrosslinkable dECM-based bioresins were prepared from digested porcine liver dECM through functionalization with glycidyl methacrylate (GMA) or conventional methacrylic anhydride (MA) under mild conditions for systematic comparison. Although the chemical modifications did not significantly affect the structural integrity of the dECM proteins, mammalian cells encapsulated in the respective hydrogels performed differently in long-term culture. In either case, photocrosslinking during 3D (bio)printing resulted in transparent, highly swollen, and soft hydrogels with good shape fidelity, excellent biomimetic properties and tunable mechanical properties (~ 0.2-2.5 kPa). Interestingly, at a similar degree of functionalization (DOF ~ 81.5-83.5 %), the dECM-GMA resin showed faster photocrosslinking kinetics in photorheology resulting in lower final stiffness and faster enzymatic biodegradation compared to the dECM-MA gels, yet comparable network homogeneity as assessed via Brillouin imaging. While human hepatic HepaRG cells exhibited comparable cell viability directly after 3D bioprinting within both materials, cell proliferation and spreading were clearly enhanced in the softer dECM-GMA hydrogels at a comparable degree of crosslinking. These differences were attributed to the additional hydrophilicity introduced to dECM via methacryloylation through GMA compared to MA. Due to its excellent printability and cytocompatibility, the functional porcine liver dECM-GMA biomaterial enables the advanced biofabrication of soft 3D tissue analogs using vat photopolymerization-based bioprinting.
The use of fluid-phase 3D printing to pattern alginate-gelatin hydrogel properties to guide cell growth and behaviour in vitro

Andrea Souza,McCarthy Kevin,Brian J Rodriguez,Emmanuel G Reynaud

DOI: https://doi.org/10.1088/1748-605X/ad51bf

2024-06-10

Abstract:Three-dimensional (3D) (bio)printing technology has boosted the advancement of the biomedical field. However, tissue engineering is an evolving field and (bio)printing biomimetic constructions for tissue formation is still a challenge. As a new methodology to facilitate the construction of more complex structures, we suggest the use of the fluid-phase 3D printing to pattern the scaffold's properties. The methodology consists of an exchangeable fluid-phase printing medium in which the constructions are fabricated and patterned during the printing process. Using the fluid-phase methodology, the biological and mechanical properties can be tailored promoting cell behaviour guidance and compartmentalization. In this study, we first assessed different formulations of alginate/gelatin to create a stable substrate capable to promote massive cell colonizationin vitroover time. Overall, formulations with lower gelatin content and 2-(N-morpholino)ethanesulfonic acid (MES) buffer as a solvent showed better stability under cell culture conditions and enhanced U2OS cell growth. Next, the fluid-phase showed better printing fidelity and resolution in comparison to air printing as it diminished the collapsing and the spread of the hydrogel strand. In sequence, the fluid-phase methodology was used to create functionalized alginate-gelatin-arginylglycylaspartic acid peptide (RGD) hydrogels via carbodiimides chemistry. The alginate-gelatin-RGD hydrogels showed an increase of 2.97-fold in cell growth and more spread substrate colonization in comparison to alginate-gelatin hydrogel. Moreover, the fluid-phase methodology was used to add RGD molecules to pre-determined parts of the alginate-gelatin substrate during the printing process promoting U2OS cell compartmentalization. In addition, different substrate stiffnesses were also created via fluid-phase by crosslinking the hydrogel with different concentrations of CaCl2during the printing process. As a result, the U2OS cells were also compartmentalized on the stiffer parts of the printings. Finally, our results showed that by combining stiffer hydrogel with RGD increasing concentrations we can create a synergetic effect and boost cell metabolism by up to 3.17-fold. This work presents an idea of a new printing process for tailoring multiple parameters in hydrogel substrates by using fluid-phase to generate more faithful replication of thein vivoenvironment.
Influence of stromal cells on lymphocyte adhesion and migration on endothelial cells.

H. McGettrick,C. Buckley,G. Ed Rainger,G. Nash

DOI: https://doi.org/10.1007/978-1-60761-461-6_4

Abstract:

Application of fuzzy measures in the product appearance value assessment

Dimethyl Sulfoxide Mediated High-Fidelity 3D Printing of Hydrogels

Fabrication of Liver Microtissue with Liver Decellularized Extracellular Matrix (decm) Bioink by Digital Light Processing (DLP) Bioprinting

3D Bioprinting of Multi-Material Decellularized Liver Matrix Hydrogel at Physiological Temperatures

3D bioprinting of Liver Microenvironment Model Using Photocrosslinkable Decellularized Extracellular Matrix based Hydrogel

Instant Gelation System As Self-Healable and Printable 3D Cell Culture Bioink Based on Dynamic Covalent Chemistry.

DEAE- Cellulose-based composite hydrogel for 3D printing application: Physicochemical, mechanical, and biological optimization

Double-Network Hydrogel 3D BioPrinting Biocompatible with Fibroblast Cells for Tissue Engineering Applications

DLP 3D Printing Meets Lignocellulosic Biopolymers: Carboxymethyl Cellulose Inks for 3D Biocompatible Hydrogels

A thermogelling organic-inorganic hybrid hydrogel with excellent printability, shape fidelity and cytocompatibility for 3D bioprinting

Direct 3D Printed Biomimetic Scaffolds Based on Hydrogel Microparticles for Cell Spheroid Growth

3D-printed scaffolds for tissue engineering applications using thermosensitive hydrogels based on biopolymer blends

Digital light processing-based bioprinting of microtissue hydrogel arrays using dextran-induced aqueous emulsion ink

Mussel-Inspired Naturally Derived Double-Network Hydrogels and Their Application in 3D Printing: from Soft, Injectable Bioadhesives to Mechanically Strong Hydrogels.

Investigation of the 3D Printability of Covalently Cross-Linked Polypeptide-Based Hydrogels

Optimization of collagen type I-hyaluronan hybrid bioink for 3D bioprinted liver microenvironments

A self-healing hydrogel and injectable cryogel of gelatin methacryloyl-polyurethane double network for 3D printing

Lubricating Micro‐Interface Assisted General Strategy for Preparing dECM‐Microparticle–Based Heterogeneous Granular Inks toward 3D Printing

Chemistry matters: A side-by-side comparison of two chemically distinct methacryloylated dECM bioresins for vat photopolymerization

The use of fluid-phase 3D printing to pattern alginate-gelatin hydrogel properties to guide cell growth and behaviour in vitro

Influence of stromal cells on lymphocyte adhesion and migration on endothelial cells.