Osteodystrophy with chronic liver disease

K. Tsunecka,Y. Tameda,K. Tameda,T. Nakano

DOI: https://doi.org/10.1007/BF02500646

Osteoporosis International

Abstract:

What problem does this paper attempt to address?

Investigation of metallurgical characterization and mechanical properties of double-sided friction stir welding of aluminum 6061 T6 alloy

Ankit Thakur,Varun Sharma,Shailendra Singh Bhadauria

DOI: https://doi.org/10.1177/09544054221092935

2022-04-12

Abstract:In the present study, the effect of tool tilt angle was investigated to appraise the metallurgical and mechanical behavior of double-sided friction stir welded joints of AA-6061 T6 alloy of 6 mm thick plates, using scrolled shoulder and frustum tool pin geometry. Two friction stir welded joints, with 0° (Joint J 1 ) and 2° (Joint J 2 ) tool tilt angles were fabricated using a fixed travel speed of 50 mm/min and tool rotational speed of 800 rpm. The metallurgical studies carried out by the electron backscattered diffraction showed that the incorporation of tool tilt angle resulted in the refinement of grains within the stir zone to a larger extent. The transverse tensile test results revealed that the joint efficiency of the J 2 welded joint improved by 12% as compared to the J 1 joint. The layered tensile specimens extracted from the different regions (first pass, second pass, and overlap region) of the stir zone of both the welded joints showed an appreciable variation in mechanical and metallurgical properties. The V-notch Charpy impact toughness test for J 2 joint showed 16% higher toughness, with the presence of a 55% shear area fraction in the fractured impact specimens, as compared to the 30% for the J 1 joint.
Parametric effect on microstructure evolution, grain size and mechanical behaviour of friction stir butt welding of AA6061-T6 alloy

Virendra Pratap Singh,Deepak Kumar,Basil Kuriachen

DOI: https://doi.org/10.1080/01694243.2024.2303244

IF: 2.431

2024-01-20

Journal of Adhesion Science and Technology

Abstract:This study examines how friction stir welding (FSW) changes the microstructure and mechanical properties of an AA6061-T6 alloy joint. Results showed that welding speeds (WSs) affected microstructure evolution, joint impact toughness, tensile strength, and ductility. Frictional heat and deformation rate affect grain size and shape. Additionally, the agitated zone on the advancing side had substantially less precipitates than on the retreating side. Tensile strength and impact toughness increased mostly due to high angle grain boundaries (HABs) and grain refining. X-ray diffraction (XRD) results revealed that intermetallic compounds, such as Mg 2 Si, MgZn 2 , and Al 2 CuMg were formed in various regions of stir zone (SZ), whereas β(Mg 2 Si) and β′′(Mg 5 Si 6 ) were found in Si-rich zones. Impact test revealed a drop in impact energy at all set of parameters when comparing to ambient temperatures (25 °C), i.e. 23%, 20%, and 22% for sample A1 (rotational speed (RS)/WS-710/40), 15%, 24%, and 30% for sample A2 (RS/WS-710/100), and 12%, 7.5%, and 17% for sample A3 (RS/WS-710/160) at 0 °C, −20 °C, and −40 °C, respectively. The maximum joint efficiency of 74.5% was obtained for sample A3. Hardness value was also found to be higher for sample A3 in SZ due to the increase the precipitates and the dislocation densities walls and substructures.

materials science, multidisciplinary,engineering, chemical,mechanics
Tensile and wear behaviour of friction stir welded AA5052 and AA6101-T6 aluminium alloys: effect of welding parameters

G. Kasirajan,Sathish Rengarajan,R. Ashok kumar,G.R. Raghav,V.S. Rao,K.J. Nagarajan

DOI: https://doi.org/10.1051/metal/2020039

2020-01-01

Abstract:To improve the performance and effectiveness of cost, constructing lightweight structure is the important factor for automobile, naval and aerospace industries. AA5052 and AA6101-T6 aluminium alloys are widely applied in transport industries, due to their lightweight and high strength and hence, joining of these two are unavoidable. Friction stir welding is an unconventional welding method, which is developed for constructing lightweight structures. This work describes the detailed study of friction stir welded dissimilar AA5052 and AA6101-T6 alloys. AA5052 and AA6101-T6 plates are welded with rotation rates of 765–1400 rpm and offset distances at advancing side of 0–2 mm. For this purpose, four levels of welding parameters based on Taguchi L 16 orthogonal array are chosen. To determine the optimum combinational levels and identify the effect of above-mentioned parameters on tensile and wear properties, Signal to Noise ratio and ANOVA respectively are used. From the results, it is observed that the combination of 1 mm offset distance at advancing side and 1400 rpm rotating speed produces better tensile and wear properties, which is due to high heat generation, sufficient flow of materials and balanced precipitation and strain hardening effects. On the other hand, the combination of 2 mm tool offset at advancing side and 765 rpm rotational rate exhibits poor properties, which is associated with low heat input, defects formation, precipitate coarsening and lesser strain hardening effects.

metallurgy & metallurgical engineering
Microstructure and mechanical properties of double side friction stir welded AA 7075 aluminum alloy

Kiran Kumar Vernapu,Venkata Durga Rajesh Kanchu,Rama Koteswara Rao Sajja,Ramakrishna Thadivaka,Srinivasa Rao Tadivaka

DOI: https://doi.org/10.1051/metal/2023091

IF: 0.9461

2024-01-04

Metallurgical Research & Technology

Abstract:Friction stir welding of aluminum alloys is, nowadays, widely used in several industries and the welded joints are expected to exhibit adequate weld characteristics. In fact, normal single side friction stir welds, particularly thick section joints, are prone to reductions in weld properties due to higher heat inputs. Double side friction stir welding (DS FSW) is considered to be one of the possible solutions to address the problem of weld property reductions. Hence, the present work aims at investigating the possibility of improving the joint properties of welds by welding from both sides. Double side friction stir welds were made using 10 mm thick AA7075 plates and the welds were investigated for mechanical properties using hardness, tensile, impact and bend tests. Microstructure, precipitate morphology and fracture surface of the samples were also studied by optical (OM), transmission electron (TEM) and scanning electron microscopies (SEM), respectively. The results showed that the weld nugget exhibits fine equiaxed grains and severe dissolution of strengthening precipitates. In addition, the hardness of the double side welds improved by about 20 HV compared with that of single side welds due to increased survival rate of strengthening precipitates in the WN and reduced PFZ's width in the HAZ. The results of tensile and impact tests showed that in DS FSW samples, the yield strength increased by about 30 MPa and impact toughness increased by 4.83 J compared with single side welds. By and large, it was observed that the better microstructural and mechanical properties can be achieved by double side friction stir welding.

metallurgy & metallurgical engineering
Optimization of process parameters of friction stir welded joints of dissimilar aluminum alloy by response surface methodology

Prashant Kumar,Sunil Kadiyan,Rajesh Kumar

DOI: https://doi.org/10.36037/ijrei.2022.6405

2023-01-01

International Journal of Research in Engineering and Innovation

Abstract:Aluminum and its alloys are lightweight, affordable, high-strength materials that find extensive use in shipbuilding, automotive, construction, aerospace, and other industrial fields. They are also resistant to corrosion. There is a requirement to join components manufactured of various aluminum alloys, namely AA6061 and AA7475, in applications like the aerospace, marine, and automotive sectors. Friction stir welding (FSW) is utilized in this study to join dissimilar plates consisting of aluminum alloys 6061 and 7475. On the tensile strength and percentage elongation of the welded joints, the impact of changing the tool pin profile, tool rotation speed, tool feed rate, and tool tilt angle has been studied. The empirical relationship between the output responses and input parameters was developed, and the perceived optimal values of UTS, % strain and micro hardness at SZ were 205.23 MPa, 16.43 %, and 81.05 HV, respectively. The optimal TS, TRS, and tilt angle values were 87.42 mmmin-1, 783.92 rev/m, and 0.48°, respectively. Due to DRX, the microstructure in the weld SZ was characterized by a very fine grain structure. Because of the decreased hardness, the grain sizes in HAZ and TMAZ are virtually comparable, and they discovered coarse grain structure and uneven temperature distribution in that region. When the TRS and TS increase, the grain size decreases in the SZ
Investigation on microstructural evolution and local mechanical performance of friction stir lap welded AA6061-T6/ AA7075-T6 joints

Kishor Kumar Jha,Rahul Kesharwani,Imam,Murshid Imam

DOI: https://doi.org/10.1016/j.engfailanal.2024.108258

IF: 4

2024-03-26

Engineering Failure Analysis

Abstract:The current study uses the friction stir lap welding (FSLW) technique to successfully fabricate two layered dissimilar AA6061/AA7075 joints. A defect-free joint with superior interfacial properties was obtained at the optimized process parameters (tool rotational speed / transverse speed) of 850 RPM/ 55 mm/min. The detailed investigations of microstructure evolution, crystallographic texture, and strength correlation were performed using the field emission scanning electron microscope (FE-SEM), optical microscope (OM), electron backscattered diffraction (EBSD), Vickers microhardness, nano-indentation, and miniature tensile tests. EBSD analysis reveals the presence of a significant grain refinement at the bottom (3.65 μm), middle (4.58 μm), and top region (6.34 μm) of stir zone (SZ) compared to AA6061 (42.56 μm) and AA7075 (34 μm) base metals. An increasing trend in the fraction of high angle grain boundary (F HAGBs ) and recrystallization fraction was noticed from top to bottom of the build within the SZ. Continuous dynamic recrystallization (CDRX) with the gradient in strain, strain rate, and temperature leads to these microstructural variations within the SZ. The microhardness study shows a decrease in microhardness in the SZ due to thermal softening and precipitate dissolution at higher temperatures. Appreciable interfacial material mixing leads to remarkable strength, ductility, and strain-hardening behaviour within the SZ, especially at the interface section. Pole figures (PF) reveal the presence of major shear texture components (B/B̅, and C) with some minor presence of A1*/A2*and A/A̅ that confirms the presence of higher strains within the SZ. The dominant presence of recrystallization textures components (like cube {0 0 1} 〈1 1 0〉, Goss {0 1 1} 〈1 0 0〉, and P {0 1 1} 〈1 2 2〉 ) within the SZ confirms the presence of the CDRX mechanism.

engineering, mechanical,materials science, characterization & testing
Experimental investigation and optimization of mechanical properties on combination of higher and lower strength of aluminum alloys

C Ganesan,K Manonmani

DOI: https://doi.org/10.1177/09544089211060642

2021-11-30

Abstract:Friction stir welding is a high potential technology for joining similar and dissimilar aluminum materials, utilized extensively in aerospace and automotive industrial applications to eradicate the problems like hot cracking, porosity, element loss, etc. due to the fusion welding process. This Research addresses the joining of two dissimilar materials of AA 5754 – H32 and AA 8090T6511 – Al-Li and their mechanical properties analysis with the effects of friction stir welding process parameters like tool rotational speed, welding speed and axial load on weld nugget zone formation quality. The significant roles of different tool pin profiles are also emphasized. A mathematical modeling equation was formed by using regression analysis to optimize the process parameter and found the best tool pin profile for defect-free weld nugget zone and higher tensile and hardness properties. This research also portrays the contribution of various pin profiles and each process parameter on the ultimate tensile strength by response surface methodology. The results indicate that the defect-free weld joints are observed with 1800 r/min of rotational speed, welding speed of 15 mm min −1 and 8.5 kN of axial load with hexagonal pin profile.
Development of mechanical property prediction model and optimization for dissimilar aluminum alloy joints with the friction stir welding (FSW) process

Yodprem Pookamnerd,Panuwat Thosa,Sittichai Charonerat,Suriya Prasomthong

DOI: https://doi.org/10.21303/2461-4262.2023.002776

2023-05-25

Abstract:Friction stir welding (FSW) is a solid-state joining process used to weld dissimilar aluminum alloys with varying material properties and compositions. Unlike traditional welding methods, FSW does not involve melting the materials being welded but instead uses a rotating tool to heat and stir the materials until they are in a plastic state. The process results in a welded joint with high strength, excellent ductility, and minimal distortion, making it a popular choice in various industries, including aerospace, automotive, and marine. AA6061-T6 (Mg-Si) and AA7075 (Al-Zn-Mg-Cu) aluminum alloys are one of the most popular grades of aluminum alloys used in current manufacturing industries, such as aerospace and automotive, joined by the Friction Stir Welding Process (FSW) technique. Taguchi orthogonal array (L9) experimental design was applied to reduce the number of insignificant factors in the process. First, the study determines three welding factors: rotation speed, travel speed, and pin eccentricity. Investigations found that travel speeds significantly on tensile strength (Ts) and elongation ( %El), but the rotational speed and tool eccentricity did not affect Ts and %El. Furthermore, considering the fabricated parameters on the hardness (HV) of the joint, it was found that all factors unaffected the HV of the joint zone at a 95 % confidence level. Next, examine the microstructure; Mg2Al3 and Al2O3 intermetallic compounds were found in the weld. Therefore, investigating the crystallite size found that welding significantly affects the crystallite size. Finally, consider the fracture surface, experimental condition A2B1C2 (optimal parameter), which is the parameter with the highest tensile strength having dimple fracture characteristics. On the other hand, the welding condition A1B3C3, the parameter with the lowest tensile strength, Small and fine dimple fracture with cleavage fracture. Because the material is highly ductile and can undergo large deformations before it is damaged. On the other hand, materials with low tensile strength exhibiting cleavage fracture indicate that the materials are brittle and can break easily under stress

English Else
Investigation on the mechanical properties and microstructural analysis of dissimilar friction stir welding of AA5154/AA7150

Sandeep Sarnobat,Indradeep Kumar,Kuldeep Kumar Saxena,Vinayak Malik

DOI: https://doi.org/10.1080/01694243.2024.2362029

IF: 2.431

2024-06-10

Journal of Adhesion Science and Technology

Abstract:Butt welds were produced on AA5154/AA7150 using the FSW method, and measurements were taken for the hardness and elongation percentage of each joint. Regression analysis was utilized to investigate the significance of each parameter and formulate a mathematical relationship. Welding was performed at 1200 rpm, with a welding speed of 90 mm/min and a tool diameter of 28 mm, resulting in defect-free welds. Failures were commonly observed at the pin and the side of AA7150. To decrease the ultimate tensile strength (UTS), the welding speed (WS) or tool rotational speed (TRS) was increased. As both TRS and WS constitute the nugget zone, variations in hardness distribution were noted across the weld zones. ANOVA was applied in this study to establish the relative importance and influence of each factor on UTS. The ANOVA results indicated that all parameters significantly impacted UTS. Specifically, WS contributed 41.42%, diameter contributed 17.57%, and TRS contributed 13.27%. A quadratic model was also developed to describe the relationship between the factors and UTS values. Based on the data, a range of 0.41% to 10.36% differences existed between projected and actual values. The strength of the model was evaluated using R-Squared (R-Sq.), resulting in an obtained R-Sq. value of 0.892. This value indicates a robust relationship between the predicted and actual values.

materials science, multidisciplinary,engineering, chemical,mechanics
Effect of welding speed on microstructure, nano-mechanical and nano-tribological characteristics of dissimilar friction stir welded AA6061-T6 and AZ31 alloy

Virendra Pratap Singh,Ashish Kumar,Deepak Kumar,Basil Kuriachen,Virendra Pratap SinghAshish KumarDeepak KumarBasil Kuriachena Department of Mechanical Engineering,National Institute of Technology Mizoram,Aizawl,Indiab Department of Mechanical Engineering,IES College of Technology,Bhopal,Indiac Department of Mechanical Engineering,Delhi Technological University,New Delhi,Indiad Department of Mechanical Engineering,Galgotias College of Engineering and Technology,Greater Noida,Indiae Department of Mechanical Engineering,Carnegie Mellon University,Pittsburgh,PA,USAf Department of Mechanical Engineering,National Institute of Technology Calicut,Kozhikode,India

DOI: https://doi.org/10.1080/01694243.2024.2302268

IF: 2.431

2024-01-13

Journal of Adhesion Science and Technology

Abstract:The microstructural, tribological, and mechanical performance of friction-stir welded AA6061-T6 and AZ31 alloys were investigated using electron back scattered diffraction, scanning electron microscope, X-ray diffraction, and electron dispersed spectroscopy methods. The non-destructive X-ray microcomputed tomography test was used to analyse weld porosity. The distribution of volumetric and surface flaws (pores) was found to be confined across the weldment. Using a novel atomic force microscopy method, the nano-tribological characteristics of the base metal and localized regions of welded sample were studied for the first time. The significant difference in wear and friction behaviour was observed in all weld zones and base metal of magnesium side, which was correlated with the hardness of these regions. AFM results showed strong variation in tribological properties in correlation with the hardness trends of different weld zones, i.e. higher hardness leads to low wear. In weldments, intermetallic compounds such as Al 12 Mg 17 and Al 3 Mg 2 were produced, resulting in nanohardness differences as measured by the nanoindentation test. The joint efficiency of 65%, 84%, and 91% were obtained at welding speeds of 16 mm/min, 20 mm/min, and 25 mm/min, respectively.

materials science, multidisciplinary,engineering, chemical,mechanics
Mathematical modeling and optimization of friction stir welding process parameters for armor-grade aluminium alloy

Gyander Ghangas,Sandeep Singhal,Saurav Dixit,Vikas Goyat,Sunil Kadiyan

DOI: https://doi.org/10.1007/s12008-022-01000-1

2022-08-07

International Journal on Interactive Design and Manufacturing (IJIDeM)

Abstract:The properties of lightweight, high strength, better corrosion resistance, high electrical conductivity, etc. made aluminium alloys one of the favorite materials for industrial purposes. The aerospace, marine, automobile and railway industries use these alloys very commonly. But the lower melting temperature, high thermal conductivity and unusual grain growth make it difficult to weld material. So solid-state welding process named friction stir welding (FSW) is used for higher welding joint efficiencies for these alloys. The performance of FSWed joints directly depends upon the levels of input parameters used for the welding process. The present study is an attempt to optimize the process parameters for FSW of armor-grade aluminium alloys AA5083. Tool design parameters (Shoulder Diameter, Shoulder Flatness and Pin Profile) along with machine parameters (welding speed) are used for variation to analyze their effects on the quality of the joints. The experiments were designed by the response surface methodology and the significance of these parameters was analyzed by ANOVA. Where all four considered parameters were found significantly affect the responses i.e. ultimate tensile strength, yield tensile strength and elongation. An optimized set of parameters was revealed by Desirability a multi-objective optimization approach. “Desirability” suggests 18.5 mm shoulder diameter, 2.0 mm shoulder flatness, square pin profile and 48.9 mm/min welding speed as a set of optimized parameters. The 77.9% joint efficiency can be achieved at the mentioned optimized parameters. To analyze the relationships between variation in responses with the variation in process parameters and the microstructure of the welded joints the microstructure analysis has been conducted. The microstructural analysis revealed that high heat input causes an unwanted grain growth in the heat-affected zone and the lower heat input causes an insufficient temperature for the softening of the material in the nugget zone.
Effect of Process Parameters on the Mechanical Properties of Simultaneous Double-Sided Friction Stir Welding Joints

Shaofei Meng,Huihui Zhao,Jiyi Dong,Wu Liu,Haitao Liu,Juliang Xiao

DOI: https://doi.org/10.1186/s10033-024-01126-1

IF: 2.964

2024-11-10

Chinese Journal of Mechanical Engineering

Abstract:Currently, conventional single-sided friction stir welding is primarily suitable for joining thin plate aluminum alloys, and its application to thick plates is still challenging in terms of welding efficiency and joint mechanical properties. Simultaneous double-sided friction stir welding (SDS-FSW) is a high-efficiency joining technique specifically developed for welding thick plates. However, there is little research on the influence of SDS-FSW process parameters on the joint mechanical properties. In this study, a 12 mm thick AA6061-T6 aluminum alloy and dual robot welding equipment are used to conduct SDS-FSW experiments exploring the influence of rotational speed and welding speed v on the mechanical properties and microstructure. The results show that when the welding parameters are = 800 r/min and v = 60–80 mm/min, smooth and defect-free thick plate aluminum alloy SDS-FSW joints can be obtained, and the macroscopic morphology of the joints is distributed in a "dumbbell" shape. The grain size in the weld nugget zone increases with increasing welding heat input. The microhardness distribution in the joint displays a "W" shape, and the hardness value of the weld nugget zone can reach 67% to 86% of that of the base metal (BM). The junction between the thermo-mechanically affected zone and the heat affected zone is the weakest region of the joint, with the lowest hardness being approximately 51% of that of the BM. When the welding parameters are = 800 r/min and v = 140 mm/min, the SDS-FSW joint has the highest tensile strength, reaching 78.43% of the BM strength and exhibiting ductile fracture characteristics. This research indicates that acceptable weld strength in thick aluminum alloys can be achieved via the SDS-FSW joining mechanism, highlighting its significant potential for industrial applications.

engineering, mechanical
Mechanical properties of AA6061T6 and AA6351T6 plates joined by friction stir welding

L. Prasad,A. Kumar,R. Jaiswal,A. Kumar,V. Kumar,A. Yadav

DOI: https://doi.org/10.1002/mawe.202100108

2022-08-01

Materialwissenschaft und Werkstofftechnik

Abstract:In this study, friction stir welding using a vertical milling machine was performed to join 5 mm thick dissimilar AA6061‐T6 and AA6351‐T6 aluminium alloy plates. The friction stir welding was performed with cylindrical and square pin tools at the tool‘s different rotational and transverse speeds. A dye penetration test (non‐destructive test) was performed to check cracks on welded joints′ surfaces. Tensile strength and hardness were investigated, and microstructure was analyzed. It showed that the welded surfaces were free from any cracks. The maximum ultimate tensile strength of 167.95 MPa was recorded for the square tool pin, while the maximum microhardness was 92 RHN for the cylindrical tool pin. The microstructure analysis of the cross‐section of joints revealed good intermixing of material in the stir zone leading to improved mechanical properties for use in aerospace, automobile, and shipbuilding industries by managing the cost of aluminium welding and increased performance. We joined two 5 mm thick dissimilar aluminium alloy plates (AA6061 and A6351) via friction stir welding. The welding was performed with cylindrial and square pin tools at different rotational speeds and transverse feeds. The mechanical properties such as tensile strength, microhardness and microstructure were investigated.

materials science, multidisciplinary
Protecting Patients from Adverse Drug Events: Propoxyphene, PIMs, and Drugs to Avoid in Older Adults

F. Curtiss,K. Fairman

DOI: https://doi.org/10.18553/jmcp.2011.17.1.60

2011-01-01

Journal of Managed Care Pharmacy

Abstract:The base of evidence for the relative harm versus benefit for commonly used prescription drugs expanded in 2010, including developments late in 2010 that reinforced the value of pharmacovigilance and the need for critical appraisal of warnings of threat to patient safety. In October 2010, the U.S. Food and Drug Administration (FDA) announced additions to the labels of all biphosphonates warning of the increased risk of atypical fracture of the femur, an outcome that although rare (representing less than 1% of all fractures of the hip and femur) had been “predominantly reported in patients taking bisphosphonates.” These drugs already carried a label warning regarding osteonecrosis of the jaw, and the additional warning precipitated widespread discussion among patients and health care professionals regarding the safety of biphosphonates and the observation that these widely used drugs were associated with adverse events that they were intended to prevent. In September 2010, a 4-year controversy over the relative benefit versus harm of rosiglitazone culminated in withdrawal of the drug from the European market and exceptionally restricted use in the United States including the requirement that patients “acknowledge they understand the [cardiovascular] risks” associated with use of rosiglitazone. The clinical irony for rosiglitazone is that it was used by millions of people with type 2 diabetes to prevent the very adverse cardiovascular events that were found to be associated with its use. It is not yet clear how much of the cardiovascular adverse event profile pioglitazone shares with rosiglitazone, and pioglitazone has a black-box warning regarding the possibility to “cause or exacerbate congestive heart failure.”
Influence of Material Properties on Microstructure and Mechanical Properties of Aluminum Alloy FSW Joints

Yubing GONG,Shanlin WANG,Rui PAN,Ziyang ZHANG

DOI: https://doi.org/10.14158/j.cnki.1001-3814.2017.15.010

2017-01-01

Abstract:The butt welding of AA1060-Y2,AA6061-T4,AAA5052-O and AA2024-T4 alloy plates with thickness of 4 mm was carried out by using friction stir welding, and the influence of material properties on the microstructure and mechanical properties of friction stir welding joints was investigated. The results show that with the increase of tensile strength and hardness of based material, the cross-sectional height of advance side Ha, the retreat side height Hr and the nugget width W increase, and the aspirate - squeezing effect in thickness direction increases. The tensile strength of friction stir welding joints is more than 80％ of the retreat side of based material, and the fracture of the joints is all located at the junction of the thermal mechanical affected zone and the heat affected zone, and the fracture mode is mainly ductile fracture.
Experimental Study on Mechanical Behaviour of Friction Stir Welded Aluminium Alloy Butt Joints

Beibei Li,Feng Shen,Jingfeng Wang,Xinhang Zhi,Yuanqing Wang,Song Lin,Yuanwen Ouyang

DOI: https://doi.org/10.1016/j.istruc.2024.106407

IF: 4.1

2024-01-01

Structures

Abstract:The purpose of this paper is to understand the softening extent and stress-strain behavior of the normal-strength 6061-T6, 6013-T6, and high-strength 7075-T6 aluminium alloy butt joints using the novel friction stir welding (FSW) technique. A total of 107 monotonic tensile coupons and 33 Vickers hardness coupons were prepared from 8- or 12-mm thick welded plates using various tool rotation speed, welding transverse speed and tool configurations. The surface morphology, stress-strain curves and hardness distribution laws after welding were evaluated. The W-shaped hardness profiles were clearly observed, with the fracture location positively correlated at the lowest point of Vickers hardness near the edge of the weld toe. The strength reduction and softening extent of extruded aluminium alloys in T6 temper induced by FSW were superior to those of aluminium alloys using fusing welding process outlined in the Chinese and European standards, indicating the effectiveness and applicability of the FSW technique in the formation of components and connections for aluminium alloy structures. Additionally, the current widely used constitutive models generally yielded under-estimations on the strength under large strains. The developed three-stage Ramberg-Osgood model, using seven key input parameters, significantly improved the accuracy and consistent predictions in the full-range stress-strain curve of FSW aluminium alloys. Furthermore, the suggested model could still achieve a great balance between accuracy and practicality when using just three common available parameters with the employment of predictive expressions on other four parameters.
Microstructure, microhardness and mechanical behavior of dissimilar AA7075/AA6061 alloys under friction stir welding

Hepeng Jia,Kai Wu

DOI: https://doi.org/10.1177/09544054241229476

2024-02-10

Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture

Abstract:Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Ahead of Print. Friction stir welding (FSW) of dissimilar AA6061 and AA7075 aluminum alloys faces challenges such as an unclear forming mechanism and low welding efficiency. In order to improve welding efficiency and elucidate the variations in metallography, Microhardness, and mechanical properties of dissimilar alloy FSW joints, this article designed FSW experiments using the Taguchi method with welding speeds ranging from 600 to 1000 mm/min. We studied the relationship between material mixing and welding defects through macroscopic metallography, microscopic metallography, and Microhardness, while the impact of welding parameters on the microstructure and properties was evaluated. The results show that void defects do not exist in dissimilar alloy FSW joints, and the Microhardness changes are "U" and "W" shaped. Material mixing played a decisive role in determining the microstructure and properties of dissimilar aluminum alloy FSW joints, with increased rotational speed enhancing material flow. The order of influence on the mechanical properties of the joint was found to be plunge depth, welding speed, and rotational speed. Under the conditions of 1000 mm/min, 2400 rpm, and 0.25 mm, the yield strength (YS) and ultimate tensile strength (UTS) of the dissimilar alloy FSW joints reached 87.3% and 73.4% of the AA6061-T6 alloy, respectively.

engineering, mechanical, manufacturing
Effects of multi-objective optimization of friction stir welding process parameter on mechanical and ballistic properties of AA5754 aluminum alloy

V. Manoj Mohan Prasath,S. Dharani Kumar,N. Mohammed Raffic

DOI: https://doi.org/10.1080/01694243.2024.2432392

IF: 2.431

2024-12-04

Journal of Adhesion Science and Technology

Abstract:Friction stir welding (FSW) is a solid-state welding process commonly used to join similar and dissimilar aluminum alloys. This study aims to investigate multi-criteria decision-making, multi-objective optimization, Taguchi's L9 design of experiments, and the technique for order preference by similarity to the ideal solution (TOPSIS) to evaluate the effects of various FSW parameters specifically, welding speed, feed, and axial load on the mechanical properties of AA5754 aluminum alloy. Following the enhancement of the welding parameters, an analysis of variance (ANOVA) was performed to identify the most influential parameter in the FSW process. The findings indicated that tensile strength, impact strength, and microhardness were predominantly affected by welding speed (94.82%), feed (3.12%), and axial load (1.32%), respectively. With a hexagonal tool and optimal process parameters of feed (20 mm/min), axial load (7 kN), and speed (1200 rpm), the joint obtained the maximum microhardness (81 HV), impact strength (3.01 J/mm 2 ), and tensile strength (163.89 MPa). The microstructure and X-ray diffraction analyses indicated that the crystals were tiny, with higher dislocations in the stir zone, indicating improved mechanical properties. In the FSW joint, dimples and voids were observed on the tensile and impact fracture surfaces. Finally, the ballistic properties of the optimized AA5754 FSW joint were determined. An asymmetric V-shaped deformation profile was observed around the impact point, with the highest deformation at the center. An increase in impact velocity from 134 to 187.6 m/s did not result in significant differences in the deformation of the FSW joint. The fracture surfaces of ballistic-tested friction stir welded joints exhibited shear regions and localized bands.

materials science, multidisciplinary,engineering, chemical,mechanics
Study on the effect of the welding environment on the dynamic recrystallization phenomenon and residual stresses during the friction stir welding process of aluminum alloy

Mahmoud Abbasi,Amin Abdollahzadeh,Behrouz Bagheri,Ahmad Ostovari Moghaddam,Farzaneh Sharifi,Mostafa Dadaei

DOI: https://doi.org/10.1177/14644207211025113

2021-06-21

Abstract:Various methods have been proposed to modify the friction stir welding. Friction stir vibration welding and underwater friction stir welding are two variants of this technique. In friction stir vibration welding, the adjoining workpieces are vibrated normal to the joint line while friction stir welding is carried out, while in underwater friction stir welding the friction stir welding process is performed underwater. The effects of these modified versions of friction stir welding on the microstructure and mechanical characteristics of AA6061-T6 aluminum alloy welded joints are analyzed and compared with the joints fabricated by conventional friction stir welding. The results indicate that grain size decreases from about 57 μm for friction stir welding to around 34 μm for friction stir vibration welding and about 23 μm for underwater friction stir welding. The results also confirm the evolution of Mg 2 Si precipitates during all processes. Friction stir vibration welding and underwater friction stir welding processes can effectively decrease the size and interparticle distance of precipitates. The strength and ductility of underwater friction stir welding and friction stir vibration welding processed samples are higher than those of the friction stir welding processed sample, and the highest strength and ductility are obtained for underwater friction stir welding processed samples. The underwater friction stir welding and friction stir vibration welding processed samples exhibit about 25% and 10% higher tensile strength compared to the friction stir welding processed sample, respectively. The results also indicate that higher compressive residual stresses are developed as underwater friction stir welding and friction stir vibration welding are applied.
Improvement of microstructure and mechanical properties of dissimilar friction stir welded aluminum/titanium joints via aluminum oxide nanopowder

Taher A. Shehabeldeen,Nagi M. El-Shafai,Ibrahim M. El-Mehasseb,Yajun Yin,Xiaoyuan Ji,Xu Shen,Jianxin Zhou

DOI: https://doi.org/10.1016/j.vacuum.2021.110216

IF: 4

2021-06-01

Vacuum

Abstract:Aluminum oxide nanopowder has been fabricated and characterized successfully to improve the properties of friction stir welded aluminum/titanium joints, which pose a great challenge due to the great difference in mechanical properties. Intermetallic compounds (IMCs) of large sizes formed at the welding interface are a significant problem that deteriorates joint strength due to the uncontrollable thermal effect generated in the joint. Therefore, friction stir processing was integrated with friction stir welding, in which a dissimilar lap joint of AA6061-T6 and Ti6Al4V was reinforced with γ-Al2O3 nanoparticles of about 8 nm in diameter. First, several attempts were conducted to determine the most effective parameters in the welding process of the aluminum/titanium reinforced joint and then the effects of γ-Al2O3 nanopowder on microstructure, mechanical properties, and weldability were analyzed and compared to a welded joint without reinforcing powder. Sound joints have been successfully produced using welding speed of 25 mm/min, and tool rotational speed of 600 rpm. Lap shear fracture load and displacement of the Al/Ti joint increased from 3.5 KN and 1.25 mm to 3.7 KN and 2.45 mm, respectively, while the hardness of the reinforced joint increased from 384 HV to 391 HV at the Al/Ti weld interface with a remarkable improvement at the Al and Ti sides.

materials science, multidisciplinary,physics, applied

Osteodystrophy with chronic liver disease

Investigation of metallurgical characterization and mechanical properties of double-sided friction stir welding of aluminum 6061 T6 alloy

Parametric effect on microstructure evolution, grain size and mechanical behaviour of friction stir butt welding of AA6061-T6 alloy

Tensile and wear behaviour of friction stir welded AA5052 and AA6101-T6 aluminium alloys: effect of welding parameters

Microstructure and mechanical properties of double side friction stir welded AA 7075 aluminum alloy

Optimization of process parameters of friction stir welded joints of dissimilar aluminum alloy by response surface methodology

Investigation on microstructural evolution and local mechanical performance of friction stir lap welded AA6061-T6/ AA7075-T6 joints

Experimental investigation and optimization of mechanical properties on combination of higher and lower strength of aluminum alloys

Development of mechanical property prediction model and optimization for dissimilar aluminum alloy joints with the friction stir welding (FSW) process

Investigation on the mechanical properties and microstructural analysis of dissimilar friction stir welding of AA5154/AA7150

Effect of welding speed on microstructure, nano-mechanical and nano-tribological characteristics of dissimilar friction stir welded AA6061-T6 and AZ31 alloy

Mathematical modeling and optimization of friction stir welding process parameters for armor-grade aluminium alloy

Effect of Process Parameters on the Mechanical Properties of Simultaneous Double-Sided Friction Stir Welding Joints

Mechanical properties of AA6061T6 and AA6351T6 plates joined by friction stir welding

Protecting Patients from Adverse Drug Events: Propoxyphene, PIMs, and Drugs to Avoid in Older Adults

Influence of Material Properties on Microstructure and Mechanical Properties of Aluminum Alloy FSW Joints

Experimental Study on Mechanical Behaviour of Friction Stir Welded Aluminium Alloy Butt Joints

Microstructure, microhardness and mechanical behavior of dissimilar AA7075/AA6061 alloys under friction stir welding

Effects of multi-objective optimization of friction stir welding process parameter on mechanical and ballistic properties of AA5754 aluminum alloy

Study on the effect of the welding environment on the dynamic recrystallization phenomenon and residual stresses during the friction stir welding process of aluminum alloy

Improvement of microstructure and mechanical properties of dissimilar friction stir welded aluminum/titanium joints via aluminum oxide nanopowder