[Conjugal murders].

S. Pandurovíc,M. Miković,Z. Uzelac-Belovski,N. Denić,B. Aleksandrić,S. Spasić

Abstract:

What problem does this paper attempt to address?

Magnesium-incorporated sol-gel Ta2O5 coating on Ti6Al4V and in vitro biocompatibility

Shuo Chen,Chengdong Zhang,Dongqin Xiao,Feng Shi,Kang Liu,Yongxian Wan,Ke Duan,Jie Weng,Gang Feng,Yiran Yin

DOI: https://doi.org/10.1016/j.surfcoat.2021.127769

IF: 4.865

2021-11-01

Surface and Coatings Technology

Abstract:Tantalum (Ta) has been used to modify the surface of titanium (Ti) due to its superior biological response under some clinically compromised situations such as osteoporosis and diabetes; however, the techniques used presented technical disadvantages. The currently study prepared Ta2O5 and Mg-incorporated Ta2O5 coatings on Ti6Al4V by a sol-gel method and compared in vitro response of rabbit bone marrow mesenchymal stem cells. Both coatings were submicrometer-thick and comprised nano-sized particles, the former being crystalline whereas the latter amorphous. Compared with uncoated Ti6Al4V, both coatings increased the corrosion resistance and water wettability, and improved the viability, proliferation, osteoblastic differentiation of the cells. Moreover, they also upregulated the expression of an angiogenesis-related gene (HIF-1α). With the exception of corrosion rate, greatest improvements were observed from the Mg-incorporated Ta2O5 coating. These improvements were probably due to the nanostructures and elements release of Mg and Ta from the coatings. All above results suggest that, Ta2O5-based coatings are promising tools for improving the biological response of Ti-based implants under compromised conditions.

physics, applied,materials science, coatings & films
3D Printing and Surface Engineering of Ti6Al4V Scaffolds for Enhanced Osseointegration in an In Vitro Study

Changyu Ma,Natan Roberto de Barros,Tianqi Zheng,Alejandro Gomez,Marshall Doyle,Jianhao Zhu,Himansu Sekhar Nanda,Xiaochun Li,Ali Khademhosseini,Bingbing Li

DOI: https://doi.org/10.3390/biomimetics9070423

2024-07-10

Abstract:Ti6Al4V superalloy is recognized as a good candidate for bone implants owing to its biocompatibility, corrosion resistance, and high strength-to-weight ratio. While dense metal implants are associated with stress shielding issues due to the difference in densities, stiffness, and modulus of elasticity compared to bone tissues, the surface of the implant/scaffold should mimic the properties of the bone of interest to assure a good integration with a strong interface. In this study, we investigated the additive manufacturing of porous Ti6Al4V scaffolds and coating modification for enhanced osteoconduction using osteoblast cells. The results showed the successful fabrication of porous Ti6Al4V scaffolds with adequate strength. Additionally, the surface treatment with NaOH and Dopamine Hydrochloride (DOPA) promoted the formation of Dopamine Hydrochloride (DOPA) coating with an optimized coating process, providing an environment that supports higher cell viability and growth compared to the uncoated Ti6Al4V scaffolds, as demonstrated by the higher proliferation ratios observed from day 1 to day 29. These findings bring valuable insights into the surface modification of 3D-printed scaffolds for improved osteoconduction through the coating process in solutions.
Selective Laser Melting of the Porous Ta Scaffold with Mg-Doped Calcium Phosphate Coating for Orthopedic Applications

Jianfeng Xu,Di Wu,Bing Ge,Maoyuan Li,Haiyu Yu,Fang Cao,Weidan Wang,Qing Zhang,Pinqiao Yi,Haiyao Wang,Liqun Song,Lingpeng Liu,Junlei Li,Dewei Zhao

DOI: https://doi.org/10.1021/acsbiomaterials.3c01503

2024-02-08

ACS Biomaterials Science & Engineering

Abstract:Addressing the repair of large-scale bone defects has become a hot research topic within the field of orthopedics. This study assessed the feasibility and effectiveness of using porous tantalum scaffolds to treat such defects. These scaffolds, manufactured using the selective laser melting (SLM) technology, possessed biomechanical properties compatible with natural bone tissue. To enhance the osteogenesis bioactivity of these porous Ta scaffolds, we applied calcium phosphate (CaP) and magnesium-doped calcium phosphate (Mg-CaP) coatings to the surface of SLM Ta scaffolds through a hydrothermal method. These degradable coatings released calcium and magnesium ions, demonstrating osteogenic bioactivity. Experimental results indicated that the Mg-CaP group exhibited biocompatibility comparable to that of the Ta group in vivo and in vitro. In terms of osteogenesis, both the CaP group and the Mg-CaP group showed improved outcomes compared to the control group, with the Mg-CaP group demonstrating superior performance. Therefore, both CaP and magnesium-CaP coatings can significantly enhance the osseointegration of three-dimensional-printed porous Ta, thereby increasing the surface bioactivity. Overall, the present study introduces an innovative approach for the biofunctionalization of SLM porous Ta, aiming to enhance its suitability as a bone implant material.

materials science, biomaterials
Immobilizing magnesium ions on 3D printed porous tantalum scaffolds with polydopamine for improved vascularization and osteogenesis

Limin Ma,Shi Cheng,Xiongfa Ji,Ye Zhou,Yusong Zhang,Qingtao Li,Chaohui Tan,Feng Peng,Yu Zhang,Wenhua Huang

DOI: https://doi.org/10.1016/j.msec.2020.111303

2020-12-01

Abstract:Large bone defects remain a worldwide healthy problem needing to be solved. 3D printed tantalum (Ta) scaffolds have enormous potential to repair bone defects and have applied in clinic in recent years. Although the porous structure of 3D printed Ta scaffolds could allow bone ingrowth, the surface property that reactive with surrounding tissue is still unfavorable and thus the early osteointegration is impeded. Magnesium (Mg), a necessary element during bone development, has been reported with effectively osteogenesis and angiogenesis capacity. Hence, in this study, three concentrations of Mg were doped on the surface of 3D printed tantalum scaffolds utilizing the surface adhesion ability of polydopamine (Ta-PDA-Mg) to improve its surface bioactivity. The physiochemical property of resultant Ta-PDA-Mg scaffold was characterized and their osteogenic and angiogenic effects were tested through a serial of experiments both in vitro and in vivo. Results show that Ta-PDA-Mg2 possessed the highest ion release, and all scaffolds showed excellent biocompatibility. The adhesion, angiogenesis and osteogenesis were all improved in Mg doping groups in vitro, while the Ta-PDA-Mg2 exhibited the best performances. Then the in vivo performance was examined through rat femur condyles bone defect model. Results demonstrate that the Ta-PDA-Mg2 significantly enhanced the vascularized bone formation and the osteointegration, which was further confirmed through pull out test. Therefore, Mg doped 3D printed Ta scaffold could improve surface bioactivity and lead to better osteogenesis and angiogenesis, which may provide novel strategy to develop bioactive customized implants in orthopedic applications.
Atomic Layer Deposition of Tantalum Oxide Films on 3D-Printed Ti6Al4V Scaffolds with Enhanced Osteogenic Property for Orthopedic Implants

Xianming Zhang,Shiwei Guan,Jiajun Qiu,Yuqin Qiao,Shi Qian,Ji Tan,Kelvin W K Yeung,Xuanyong Liu

DOI: https://doi.org/10.1021/acsbiomaterials.3c00217

2023-07-10

Abstract:There is an evident advantage in personalized customization of orthopedic implants by 3D-printed titanium (Ti) and its alloys. However, 3D-printed Ti alloys have a rough surface structure caused by adhesion powders and a relatively bioinert surface. Therefore, surface modification techniques are needed to improve the biocompatibility of 3D-printed Ti alloy implants. In the present study, porous Ti6Al4V scaffolds were manufactured by a selective laser melting 3D printer, followed by sandblasting and acid-etching treatment and atomic layer deposition (ALD) of tantalum oxide films. SEM morphology and surface roughness tests confirmed that the unmelted powders adhered on the scaffolds were removed by sandblasting and acid-etching. Accordingly, the porosity of the scaffold increased by about 7%. Benefiting from the self-limitation and three-dimensional conformance of ALD, uniform tantalum oxide films were formed on the inner and outer surfaces of the scaffolds. Zeta potential decreased by 19.5 mV after depositing tantalum oxide films. The in vitro results showed that the adhesion, proliferation, and osteogenic differentiation of rat bone marrow mesenchymal stem cells on modified Ti6Al4V scaffolds were significantly enhanced, which may be ascribed to surface structure optimization and the compatibility of tantalum oxide. This study provides a strategy to improve the cytocompatibility and osteogenic differentiation of porous Ti6Al4V scaffolds for orthopedic implants.
Facile Fabrication of 3D-Printed Porous Ti6Al4V Scaffolds with a Sr-CaP Coating for Bone Regeneration

Shenghui Su,Weidong Chen,Minghui Zheng,Guozan Lu,Wei Tang,Haihong Huang,Dongbin Qu

DOI: https://doi.org/10.1021/acsomega.1c05908

IF: 4.1

2022-03-01

ACS Omega

Abstract:To improve osseointegration caused by the stress-shielding effect and the inert nature of titanium-based alloys, in this work, we successfully constructed a strontium calcium phosphate (Sr-CaP) coating on three-dimensional (3D)-printed Ti6Al4V scaffolds to address this issue. The energy-dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) results indicated that the coatings with and without Sr doping mainly consisted of CaHPO4. The bonding strength of Sr doping coating met the required ISO 13 779-4-2018 standard (≥15 MPa). The in vitro results suggested that the Sr-CaP-modified Ti6Al4V scaffolds were found to effectively promote mice bone-marrow stem cell (mBMSC) adhesion, spreading, and osteogenesis. The in vivo experiments also showed that the Sr-CaP-modified Ti6Al4V scaffolds could significantly improve bone regeneration and osseointegration. More importantly, Sr-doped CaP-coated Ti6Al4V scaffolds were found to accelerate bone healing in comparison to CaP-coated Ti6Al4V scaffolds. The Sr-CaP-modified Ti6Al4V scaffolds are considered a promising strategy to develop bioactive surfaces for enhancing the osseointegration between the implant and bone tissue.

chemistry, multidisciplinary
Osteoinduction Evaluation of Fluorinated Hydroxyapatite and Tantalum Composite Coatings on Magnesium Alloys

Zheng Cao,Li Li,Linjun Yang,LiLi Yao,Haiyan Wang,Xiaoyang Yu,Xinkun Shen,Litao Yao,Gang Wu

DOI: https://doi.org/10.3389/fchem.2021.727356

IF: 5.5

2021-09-07

Frontiers in Chemistry

Abstract:Magnesium (Mg) alloys have a wide range of biomaterial applications, but their lack of biocompatibility and osteoinduction property impedes osteointegration. In order to enhance the bioactivity of Mg alloy, a composite coating of fluorinated hydroxyapatite (FHA) and tantalum (Ta) was first developed on the surface of the alloy through thermal synthesis and magnetron sputtering technologies in this study. The samples were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS) mapping, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and water contact angle measurement (WCA), which characterized the surface alternation and confirmed the deposition of the target FHA/Ta coating. The results of cell morphology showed that the MC3T3-E1 cells on the surface of Mg/FHA/Ta samples had the largest spreading area and lamellipodia. Moreover, the FHA coating endowed the surface with superior cell viability and osteogenic properties, while Ta coating played a more important role in osteogenic differentiation. Therefore, the combination of FHA and Ta coatings could synergistically promote biological functions, thus providing a novel strategy for implant design.

chemistry, multidisciplinary
Surface-treated 3D printed Ti-6Al-4V scaffolds with enhanced bone regeneration performance: an in vivo study

Guangdao Zhang,Pengyu Zhao,Lin Lin,Limei Qin,Zhiguang Huan,Sander Leeflang,Amir A. Zadpoor,Jie Zhou,Lin Wu

DOI: https://doi.org/10.21037/atm-20-3829

IF: 3.616

2021-01-01

Annals of Translational Medicine

Abstract:BACKGROUND: Given their highly adjustable and predictable properties, three-dimensional(3D) printed geometrically ordered porous biomaterials offer unique opportunities as orthopedic implants. The performance of such biomaterials is, however, as much a result of the surface properties of the struts as it is of the 3D porous structure. In our previous study, we have investigated the in vitro performances of selective laser melted (SLM) Ti-6Al-4V scaffolds which are surface modified by the bioactive glass (BG) and mesoporous bioactive glass (MBG), respectively. The results demonstrated that such modification enhanced the attachment, proliferation, and differentiation of human bone marrow stromal cells (hBMSC). Here, we take the next step by assessing the therapeutic potential of 3D printed Ti-6Al-4V scaffolds with BG and MBG surface modifications for bone regeneration in a rabbit bone defect model.METHODS: 3D printed Ti-6Al-4V scaffolds with BG and MBG surface modifications were implanted into the femoral condyle of the rabbits, the Ti-6Al-4V scaffolds without surface modification were used as the control. At week 3, 6, and 9 after the implantation, micro-computed tomography (micro-CT) imaging, fluorescence double-labeling to determine the mineral apposition rate (MAR), and histological analysis of non-decalcified sections were performed.RESULTS: We found significantly higher volumes of regenerated bone, significantly higher values of the relevant bone morphometric parameters, clear signs of bone matrix apposition and maturation, and the evidence of progressed angiogenesis and blood vessel formation in the groups where the bioactive glass was added as a coating, particularly the MGB group.CONCLUSIONS: The MBG coating resulted in enhanced osteoconduction and vascularization in bone defect healing, which was attributed to the release of silicon and calcium ions and the presence of a nano-mesoporous structure on the surface of the MBG specimens.

oncology,medicine, research & experimental
Interleukin-12 expression in B cells by transformation with Epstein-Barr virus.

T. Yoshimoto,H. Nagase,T. Yoneto,J. Inoue,H. Nariuchi

DOI: https://doi.org/10.1006/BBRC.1998.9693

1998-11-27

Abstract:Although interleukin (IL)-12 was originally purified from an Epstein-Barr (EBV)-transformed B cell line and the high correlation of EBV infection and IL-12 expression has been suggested, no study has reported whether EBV infection is directly linked to IL-12 expression. To address this issue, we have investigated IL-12 expression in B cells during in vitro transformation with EBV. Human peripheral B cells became capable of constitutively producing p40 by in vitro transformation with EBV, coincident with the expression of latent membrane protein 1 (LMP1) of EBV. These B cells expressed p40 and p35 mRNA, and phorbol myristate acetate (PMA) stimulation strongly enhanced p40 and p70 production. Furthermore, transfection with LMP1 expression vector into a human B lymphoma cell line, Daudi, led to p40 production with nuclear factor (NF)-kappaB activation. These results suggest that transformation of primary B cells with EBV induces IL-12 expression potentially through LMP1 expression.
Biofunctional magnesium coated Ti6Al4V scaffold enhances osteogenesis and angiogenesis in vitro and in vivo for orthopedic application

Peng Gao,Bo Fan,Xiaoming Yu,Wenwen Liu,Jie Wu,Lei Shi,Di Yang,Lili Tan,Peng Wan,Yulin Hao,Shujun Li,Wentao Hou,Ke Yang,Xiaokang Li,Zheng Guo

DOI: https://doi.org/10.1016/j.bioactmat.2020.04.019

IF: 18.9

2020-09-01

Bioactive Materials

Abstract:The insufficient osteogenesis and osseointegration of porous titanium based scaffold limit its further application. Early angiogenesis is important for scaffold survival. It is necessary to develop a multifunctional surface on titanium scaffold with both osteogenic and angiogenic properties. In this study, a biofunctional magnesium coating is deposited on porous Ti6Al4V scaffold. For osseointegration and osteogenesis analysis, in vitro studies reveal that magnesium-coated Ti6Al4V co-culture with MC3T3-E1 cells can improve cell proliferation, adhesion, extracellular matrix (ECM) mineralization and ALP activity compared with bare Ti6Al4V cocultivation. Additionally, MC3T3-E1 cells cultured with magnesium-coated Ti6Al4V show significantly higher osteogenesis-related genes expression. In vivo studies including fluorochrome labeling, micro-computerized tomography and histological examination of magnesium-coated Ti6Al4V scaffold reveal that new bone regeneration is significantly increased in rabbits after implantation. For angiogenesis studies, magnesium-coated Ti6Al4V improve HUVECs proliferation, adhesion, tube formation, wound-healing and Transwell abilities. HUVECs cultured with magnesium-coated Ti6Al4V display significantly higher angiogenesis-related genes (HIF-1α and VEGF) expression. Microangiography analysis reveal that magnesium-coated Ti6Al4V scaffold can significantly enhance the blood vessel formation. This study enlarges the application scope of magnesium and provides an optional choice to the conventional porous Ti6Al4V scaffold with enhanced osteogenesis and angiogenesis for further orthopedic applications.

engineering, biomedical,materials science, biomaterials
Study of Bone Regeneration and Osteointegration Effect of a Novel Selective Laser-Melted Titanium-Tantalum-Niobium-Zirconium Alloy Scaffold

Yu Guo,Junxiang Wu,Kai Xie,Jia Tan,Yangzi Yang,Shuang Zhao,Lei Wang,Wenbo Jiang,Yongqiang Hao

DOI: https://doi.org/10.1021/acsbiomaterials.9b00909

2019-11-04

Abstract:Titanium-tantalum-niobium-zirconium (Ti-Ta-Nb-Zr) alloy is a novel material currently available for orthopedic applications. However, these scaffolds, manufactured using traditional methods, present disadvantages such as irregular pore size, unsuitable mechanical features, and poor connectivity between pores. In this study, porous Ti-Ta-Nb-Zr (60% Ti, 2% Ta, 36% Nb, and 2% Zr) scaffolds were printed by selective laser melting (SLM) with a controllable pore size of 300–400 μm. The mechanical properties of the SLM-manufactured scaffolds were evaluated, as well as its osteogenesis in vitro and osteointegration in vivo. Porous Ti-Ta-Nb-Zr scaffolds yielded superior cell proliferation and cell adhesion results with human bone mesenchymal stem cells (hBMSCs) compared with porous Ti6Al4V scaffolds. The osteogenic differentiation experiment demonstrated enhanced osteogenic differentiation of hBMSCs in the Ti-Ta-Nb-Zr group than in the Ti6Al4V group. After the porous Ti-Ta-Nb-Zr or control scaffolds were implanted into a cylindrical bone defect in the rabbit lateral femoral condyle, the initial radiological results confirmed the excellent osteogenic activity of the novel 3D-printed scaffolds. Histological analysis further indicated that the Ti-Ta-Nb-Zr scaffolds promoted bone regeneration and osteointegration more effectively than Ti6Al4V scaffolds. Our findings demonstrate that the SLM-manufactured porous Ti-Ta-Nb-Zr scaffold has considerable potential for clinical orthopedic application.

materials science, biomaterials
Additive manufacturing of magnesium-doped calcium silicate/zirconia ceramic scaffolds with projection-based 3D printing: Sintering, mechanical and biological behavior

Huifeng Shao,Jiahua Zhu,Xiao Zhao,Pengcheng Xia,Yujie Wang,Tao Zhang,Youping Gong,Yong He,Qingqiang Yao

DOI: https://doi.org/10.1016/j.ceramint.2023.12.244

IF: 5.532

2023-12-01

Ceramics International

Abstract:The lack of traditional bioactivity in zirconia (ZrO2) and limitations in the personalization capabilities of conventional manufacturing processes pose significant challenges for alveolar bone defect repair. This study aims to investigate whether ZrO2/CSi-Mgx scaffolds, produced by combining magnesium-doped calcium silicate (CSi–Mg) as a doping phase with ZrO2 as the matrix, using projection-based 3D printing (3DPP) technology, exhibit favorable biocompatibility and mechanical properties at low sintering temperatures. The effect of CSi–Mg content (x%), pore structure and heating temperature on the strength of scaffolds were investigated systematically. Incorporation of CSi–Mg could readily adjust the sintering properties of the ZrO2 scaffolds and the scaffolds with low (10–20 %) CSi–Mg possess much higher strength (74–92 MPa) after 1150 °C. Meanwhile, the ZrO2/CSi–Mg10 scaffolds with Triply periodic minimum surfaces (TPMS) pore structure had a compression strength of over 92 MPa and maintained a respectable strength (63 MPa) even after immersion in Tris buffer for 6 weeks. Concurrently, cellular experiments showed that incorporation of CSi–Mg could enhance cellular adhesion, proliferation, and migration of the ZrO2 scaffolds and also promote the osteogenic property of the scaffolds. In conclusion, the ZrO2/CSi–Mg10 scaffold with TPMS pore structure showcases remarkable mechanical performance and bioactivity, holding the potential to facilitate in-situ bone regeneration within the alveolar bone.

materials science, ceramics
3D printing of dual-cell delivery titanium alloy scaffolds for improving osseointegration through enhancing angiogenesis and osteogenesis

Heng Zhao,Shi Shen,Lu Zhao,Yulin Xu,Yang Li,Naiqiang Zhuo

DOI: https://doi.org/10.1186/s12891-021-04617-7

IF: 2.562

2021-08-27

BMC Musculoskeletal Disorders

Abstract:Abstract Background The repair of large bone defects is a great challenge for orthopedics. Although the development of three-dimensional (3D) printed titanium alloy (Ti6Al4V) implants with optimized the pore structure have effectively promoted the osseointegration. However, due to the biological inertia of Ti6Al4Vsurface and the neglect of angiogenesis, some patients still suffer from postoperative complications such as dislocation or loosening of the prosthesis. Methods The purpose of this study was to construct 3D printed porous Ti6Al4V scaffolds filled with bone marrow mesenchymal stem cells (BMSC) and endothelial progenitor cells (EPC) loaded hydrogel and evaluate the efficacy of this composite implants on osteogenesis and angiogenesis, thus promoting osseointegration. Results The porosity and pore size of prepared 3D printed porous Ti6Al4V scaffolds were 69.2 ± 0.9 % and 593.4 ± 16.9 μm, respectively, which parameters were beneficial to bone ingrowth and blood vessel formation. The BMSC and EPC filled into the pores of the scaffolds after being encapsulated by hydrogels can maintain high viability. As a cell containing composite implant, BMSC and EPC loaded hydrogel incorporated into 3D printed porous Ti6Al4V scaffolds enhancing osteogenesis and angiogenesis to repair bone defects efficiently. At the transcriptional level, the composite implant up-regulated the expression levels of the osteogenesis-related genes alkaline phosphatase ( ALP ) and osteocalcin ( OCN ), and angiogenesis-related genes hypoxia-inducible factor 1 alpha ( HIF-1α ), and vascular endothelial growth factor ( VEGF ). Conclusions Overall, the strategy of loading porous Ti6Al4V scaffolds to incorporate cells is a promising treatment for improving osseointegration.

orthopedics,rheumatology
The osteogenic, inflammatory and osteo-immunomodulatory performances of biomedical Ti-Ta metal-metal composite with Ca- and Si-containing bioceramic coatings

Qianli Huang,Xuezhong Li,Tarek A Elkhooly,Shenghang Xu,Xujie Liu,Qingling Feng,Hong Wu,Yong Liu

DOI: https://doi.org/10.1016/j.colsurfb.2018.05.010

2018-09-01

Abstract:It is known that good mechanical properties, low modulus to reduce stress-shielding effect, favorable osteogenic activity and limited inflammatory response are critical factors for orthopedic implants to induce excellent osteointegration. In this study, Ti-20% Ta metal-metal composite (referred as Ti-Ta) which consisted of Ti- and Ta-rich phases was fabricated via the strategy of powder metallurgy. Micro-arc oxidation (MAO) was employed to modify the surface of Ti-Ta composite. The surfaces of Ti-Ta composite after MAO treatment at an applied voltage of 250 (referred as MAO-250 V) or 300 V (referred as MAO-300 V) exhibited three distinct zones with significantly different morphological features and surface chemistry. Osteoblast-like SaOS-2 cells were found to be preferential to attach on the Ta-rich phase and its surrounding areas, exhibiting an area-dependent adhesion tendency. However, the attachment of Raw 264.7 macrophages was found to be insensitive to the surface characteristics. The proliferation and differentiation of SaOS-2 cells cultured on various surfaces basically followed the trend: MAO-modified surfaces > Ti-Ta surface > Ti surface. The Ti-Ta and MAO-modified surfaces were found to inhibit the inflammatory response and polarize macrophages to anti-inflammatory M2 phenotype compared to Ti surface. Moreover, the microenvironments created by Ti-Ta, MAO-250 V and MAO-300 V/macrophage interactions promoted the proliferation and differentiation of SaOS-2 cells compared to that created by Ti/macrophage interactions. MAO-300 V surface exhibited further enhanced positive osteo-immunomodulatory effects compared to Ti-Ta surface. Together, the Ti-20% Ta metal-metal composite modified by MAO at an applied voltage of 300 V is considered as a promising implant material for orthopedic applications.
Porous tantalum structure integrated on Ti6Al4V base by Laser Powder Bed Fusion for enhanced bony-ingrowth implants: In vitro and in vivo validation

Pengfei Lei,Hu Qian,Taomei Zhang,Ting Lei,Yihe Hu,Chao Chen,Kechao Zhou

DOI: https://doi.org/10.1016/j.bioactmat.2021.05.025

IF: 18.9

2022-01-01

Bioactive Materials

Abstract:Novel Ti6Al4V-based porous Ta scaffolds were successfully manufactured using LPBF.Scaffolds were biomechanically compatible, the interfacial bonding strength was high.In vitro and in vivo biocompatibility was high in r-BMSCs and rabbits, respectively.The scaffold possesses great potential for orthopedic clinical applications.Despite the widespread application of Ti6Al4V and tantalum (Ta) in orthopedics, bioinertia and high cost limit their further applicability, respectively, and tremendous efforts have been made on the Ti6Al4V-Ta alloy and Ta coating to address these drawbacks. However, the scaffolds obtained are unsatisfactory. In this study, novel high-interface-strength Ti6Al4V-based porous Ta scaffolds were successfully manufactured using Laser Powder Bed Fusion for the first time, in which porous Ta was directly manufactured on a solid Ti6Al4V substrate. Mechanical testing revealed that the novel scaffolds were biomechanically compatible, and the interfacial bonding strength was as high as 447.5 MPa. In vitro biocompatibility assay, using rat bone marrow mesenchymal stem cells (r-BMSCs), indicated that the novel scaffolds were biocompatible. Alkaline phosphatase and mineralized nodule determination demonstrated that the scaffolds favored the osteogenic differentiation of r-BMSCs. Moreover, scaffolds were implanted into rabbits with femur bone defects, and imaging and histological evaluation identified considerable new bone formation and bone ingrowth, suggesting that the scaffolds were well integrated with the host bone. Overall, these results demonstrated good mechanical compatibility, biocompatibility, and osteointegration performance of the novel Ti6Al4V-based porous Ta scaffold, which possesses great potential for orthopedic clinical applications.<ol class="links-for-figure"><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S2452199X21002450-ga1_lrg.jpg">Download : Download high-res image (348KB)</a></li><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S2452199X21002450-ga1.jpg">Download : Download full-size image</a></li></ol>

engineering, biomedical,materials science, biomaterials
Enhancing the immunomodulatory osteogenic properties of Ti-Mg alloy by Mg2+-containing nanostructures

Luxin Liang,Zhengjun Lin,Ziqing Duan,Solomon-Oshioke Agbedor,Ning Li,Ian Baker,Bing Wang,Tang Liu,Hong Wu

DOI: https://doi.org/10.1093/rb/rbae104

2024-08-29

Regenerative Biomaterials

Abstract:Abstract Facilitating an appropriate immune response is crucial for promoting bone tissue regeneration upon biomaterial implantation. In this study, the Mg2+-containing nanostructures on the surface of Ti-1.25 Mg alloy were prepared by a one-step hydrothermal reaction method via regulating pH value to enhance the immunomodulatory osteogenic properties of Ti-Mg alloys. In neutral (HT7) or alkaline (HT9) hydrothermal treatment solution, the size of MgTiO3 nanostructures formed on the surface of Ti-1.25 Mg alloy is smaller than that in acidic hydrothermal treatment solution (HT5), and lamellar Mg(OH)2 nanostructures are found in HT7 and HT9. In addition, the sample surface has a lower roughness and higher wettability with increasing pH value. The Mg2+-containing nanostructures on the Ti-1.25 Mg alloy inhibited inflammatory response by promoting the polarization of M2 macrophages, thereby promoting osteogenesis in vitro. The micro-CT and histological assessment proved that the regeneration of bone defect was faster in HT7 than the Ti-1.25 Mg in vivo. Mechanically, Mg2+-containing nanostructures can mediate the immune response of macrophages via up-regulating integrins α5β1 and inhibiting Toll-like receptors (TLR-4), subsequently inhibiting the NF-κB signaling pathway. Overall, osteoimmunity-regulating Mg2+-containing nanostructures on Ti-1.25 Mg present a promising biomaterial for bone repair.

materials science, biomaterials
Buruli ulcer caused by "Mycobacterium ulcerans subsp. shinshuense".

Tessin Watanabe,K. Ohkusu,K. Nakanaga,N. Ishii,K. Nakashima,M. Shindo,Y. Yoshida,O. Yamamoto

DOI: https://doi.org/10.1684/ejd.2010.1067

2010-11-01

Abstract:Auteur(s) : Tessin Watanabe1, Kiyofumi Ohkusu2, Kazue Nakanaga3, Norihisa Ishii3, Keiko Nakashima1, Masahisa Shindo1, Yuichi Yoshida1, Osamu Yamamoto1 1Division of Dermatology, Department of Medicine of Sensory and Motor Organs, Faculty of Medicine, Tottori University, 86 Nishi-cho, Yonago 683-8503, Japan 2Department of Microbiology, Gifu University Graduate School of Medicine, Yanagido Gifu 501-1194, Japan 3Leprosy Research Center, National Institute of Infectious [...]
Retroid virus genome replication.

W. Mason,W. Mason,Johnm . Taylor,Johnm . Taylor,R. Hull,R. Hull

DOI: https://doi.org/10.1016/S0065-3527(08)60474-1

Advances in Virus Research

Abstract:
Bone regeneration of hollow tubular magnesium‑strontium scaffolds in critical-size segmental defects: Effect of surface coatings

W Wang,K C Nune,L Tan,N Zhang,J Dong,J Yan,R D K Misra,K Yang

DOI: https://doi.org/10.1016/j.msec.2019.02.067

Abstract:Segmental defects are formidable challenges for orthopedic surgeons that are caused by large osseous defects such as open injury, comminuted fracture as well as other severe traumas and infection. Current treatment options have practical and clinical shortcomings, calling for innovative bone graft materials. This study is related to hollow tubular magnesium‑strontium (MgSr) alloy scaffolds with autologous morselized bone filled inside and three different coatings were individually applied on MgSr scaffolds, respectively, to study the effects of degradation and bioactivity of the grafts on new bone growth. The optimal coating method was screened using immersion tests, cell proliferation and adhesion, alkaline phosphatase (ALP) assay in vitro, and 4 weeks' implantation in a critical-size segmental defect in vivo. More new bone formation was observed by radiographic tests and histology along the ulna defects, when magnesium scaffold grafts were implanted. Meanwhile, depression occurred for blank control group with only autologous morselized bone filled, because of rapid absorption rate of morselized bone during initial implantation. Therefore, biodegradable MgSr alloy grafts showed their potential application in treating the critical-size segmental defects. As for different coating methods, CaP chemically deposited (CaP) coated sample showed least H2 evolution in vivo, demonstrating highest corrosion resistance and relative stable interfaces, however, the least beneficial ion release meanwhile. Micro-arc oxidation coating (MAO) degraded faster comparing with CaP, while with the main composition of MgO. They both indicate insufficient bioactivity in bone formation. The results suggest superior combination of bioactive surface, beneficial ions release and appropriate corrosion rate of Strontium phosphate conversion (SrP) coating, indicating superior comprehensive oeteoconductive and osteoinductive properties of coatings on hollow tubular MgSr alloy scaffold.
Highly biologically functional magnesium silicate-coated 3D printed round pore-shaped titanium scaffold alters exosomal miRNA expression to promote osteogenic differentiation for bone defect repair

Xuwei Luo,Zhencheng Xiong,Dong Wang,Renliang Zhao,Xiangtian Deng,Ao Duan,Chaoyi Zhang,Wenzheng Liu,Zilu Ge,Zhen Zhang,Qian Fang,Dongqin Xiao,Wei Lin,Guanglin Wang

DOI: https://doi.org/10.1016/j.cej.2024.151372

IF: 15.1

2024-04-20

Chemical Engineering Journal

Abstract:Bone defects are a serious condition that has a significant impact on the function and quality of life of the patient. In severe bone defects, restoring the structure and function of bone tissue is a complex task, and titanium (Ti) implants designed with superior performance can be an alternative. In this study, in order to develop a Ti implant that effectively promotes osseointegration and new bone ingrowth, 3D printing-based magnesium silicate (MgSiO 3 )-coated round pore-shaped Ti scaffold (S-R/MgSi) was fabricated by standardizing pore size and porosity and designing different pore shapes and selecting the optimal pore shape (round) as well as subsequent hydrothermal synthesis to finally form MgSiO 3 coating. The experimental results of Ti scaffolds with different pore shapes showed that S-R is optimal for promoting osteogenic differentiation. After S-R was coated with MgSiO 3 , S-R/MgSi enhanced the adhesion, proliferation, migration, and osteogenic differentiation of bone marrow mesenchymal stem cells (BMSCs), as well as regulated angiogenesis. In vivo studies, S-R/MgSi significantly promoted new bone ingrowth and was effective in repairing bone defects. Following the mechanism exploration, it was found that exosomes secreted by BMSCs co-cultured with S-R/MgSi (Exo_S-R/MgSi) were more able to promote the osteogenic differentiation of BMSCs. In conclusion, this study not only successfully prepared a new type of Ti implant with superior ability to promote new bone ingrowth, but also provided a new explanation for the mechanism of scaffold surface chemistry affecting osteogenesis from the viewpoint of scaffold surface coating affecting the amount and function of cellular exosome secretion.

engineering, chemical, environmental

[Conjugal murders].

Magnesium-incorporated sol-gel Ta2O5 coating on Ti6Al4V and in vitro biocompatibility

3D Printing and Surface Engineering of Ti6Al4V Scaffolds for Enhanced Osseointegration in an In Vitro Study

Selective Laser Melting of the Porous Ta Scaffold with Mg-Doped Calcium Phosphate Coating for Orthopedic Applications

Immobilizing magnesium ions on 3D printed porous tantalum scaffolds with polydopamine for improved vascularization and osteogenesis

Atomic Layer Deposition of Tantalum Oxide Films on 3D-Printed Ti6Al4V Scaffolds with Enhanced Osteogenic Property for Orthopedic Implants

Facile Fabrication of 3D-Printed Porous Ti6Al4V Scaffolds with a Sr-CaP Coating for Bone Regeneration

Osteoinduction Evaluation of Fluorinated Hydroxyapatite and Tantalum Composite Coatings on Magnesium Alloys

Surface-treated 3D printed Ti-6Al-4V scaffolds with enhanced bone regeneration performance: an in vivo study

Interleukin-12 expression in B cells by transformation with Epstein-Barr virus.

Biofunctional magnesium coated Ti6Al4V scaffold enhances osteogenesis and angiogenesis in vitro and in vivo for orthopedic application

Study of Bone Regeneration and Osteointegration Effect of a Novel Selective Laser-Melted Titanium-Tantalum-Niobium-Zirconium Alloy Scaffold

Additive manufacturing of magnesium-doped calcium silicate/zirconia ceramic scaffolds with projection-based 3D printing: Sintering, mechanical and biological behavior

3D printing of dual-cell delivery titanium alloy scaffolds for improving osseointegration through enhancing angiogenesis and osteogenesis

The osteogenic, inflammatory and osteo-immunomodulatory performances of biomedical Ti-Ta metal-metal composite with Ca- and Si-containing bioceramic coatings

Porous tantalum structure integrated on Ti6Al4V base by Laser Powder Bed Fusion for enhanced bony-ingrowth implants: In vitro and in vivo validation

Enhancing the immunomodulatory osteogenic properties of Ti-Mg alloy by Mg2+-containing nanostructures

Buruli ulcer caused by "Mycobacterium ulcerans subsp. shinshuense".

Retroid virus genome replication.

Bone regeneration of hollow tubular magnesium‑strontium scaffolds in critical-size segmental defects: Effect of surface coatings

Highly biologically functional magnesium silicate-coated 3D printed round pore-shaped titanium scaffold alters exosomal miRNA expression to promote osteogenic differentiation for bone defect repair