Mechanisms of calcium release in sarcoplasmic reticulum.

G. Inesi,N. Malan

DOI: https://doi.org/10.1016/0024-3205(76)90001-1

1976-04-15

Life Science

Abstract:

What problem does this paper attempt to address?

Valorization and optimization of Prosopis africana pod and cowpea husk wastes for densified hybrid briquette production

Chidiebele Uzoagba,Michael Mozie,Abdulhakeem Bello,Rejoice N. Ossei-Bremang,Edmund Okoroigwe,Marzieh Kadivar,Fayen Odette Ngasoh,Vitalis O. Anye,Francis Kemausuor,Peter Azikiwe Onwualu

DOI: https://doi.org/10.1080/17597269.2024.2414150

2024-11-01

Biofuels

Abstract:Biomass is an eco-friendly alternative sustainable renewable energy source when agricultural wastes are effectively utilized. It has become critical to assess the suitability of biofuel briquettes as an energy source for cooking, electricity, and fuel for heating. Certainly, the integration of energy sources into energy policies is warranted, considering the huge potential to provide energy for rural communities and the peri-urban poor with alternative fuel. This research describes a technique to generate densified hybrid solid biofuels from biomass waste and valorize them. Prosopis africana pod (PAP) and cowpea husk (CPH) wastes were combined to create high-energy-density fuel briquettes. The experiment involves improving briquette manufacturing parameters using response surface methodology to better understand the impacts of particle sizes, composition, binder concentrations, and densification pressures on briquette performance. The optimal conditions were particle size 150 μm, 50% PAP, 10% binder concentration, and densification pressure 103.42 kN/m 2 . The optimum values for burning rate, ignition time, specific fuel consumption, and heating value were 0.35 g/min, 2.75 min, 0.186 g/L, and 22.98 MJ/kg, respectively. The findings show the potential for using PAP and CPH biomass waste to produce environmentally friendly energy sources. This increases the potential agro-waste feedstocks for bioenergy in developing countries, reducing energy insecurity while promoting waste management, renewable energy generation, and environmental sustainability.

energy & fuels
Processing and properties of a solid energy fuel from municipal solid waste (MSW) and recycled plastics

JeongIn Gug,David Cacciola,Margaret J Sobkowicz

DOI: https://doi.org/10.1016/j.wasman.2014.09.031

Abstract:Diversion of waste streams such as plastics, woods, papers and other solid trash from municipal landfills and extraction of useful materials from landfills is an area of increasing interest especially in densely populated areas. One promising technology for recycling municipal solid waste (MSW) is to burn the high-energy-content components in standard coal power plant. This research aims to reform wastes into briquettes that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, free of hazardous contaminants, and moisture resistant, while retaining high fuel value. This study aims to investigate the effects of processing conditions and added recyclable plastics on the properties of MSW solid fuels. A well-sorted waste stream high in paper and fiber content was combined with controlled levels of recyclable plastics PE, PP, PET and PS and formed into briquettes using a compression molding technique. The effect of added plastics and moisture content on binding attraction and energy efficiency were investigated. The stability of the briquettes to moisture exposure, the fuel composition by proximate analysis, briquette mechanical strength, and burning efficiency were evaluated. It was found that high processing temperature ensures better properties of the product addition of milled mixed plastic waste leads to better encapsulation as well as to greater calorific value. Also some moisture removal (but not complete) improves the compacting process and results in higher heating value. Analysis of the post-processing water uptake and compressive strength showed a correlation between density and stability to both mechanical stress and humid environment. Proximate analysis indicated heating values comparable to coal. The results showed that mechanical and moisture uptake stability were improved when the moisture and air contents were optimized. Moreover, the briquette sample composition was similar to biomass fuels but had significant advantages due to addition of waste plastics that have high energy content compared to other waste types. Addition of PP and HDPE presented better benefits than addition of PET due to lower softening temperature and lower oxygen content. It should be noted that while harmful emissions such as dioxins, furans and mercury can result from burning plastics, WTE facilities have been able to control these emissions to meet US EPA standards. This research provides a drop-in coal replacement that reduces demand on landfill space and replaces a significant fraction of fossil-derived fuel with a renewable alternative.
Biofuel characteristics of non-charred briquettes from dried fecal sludge blended with food market waste: Suggesting a waste-to-biofuel enterprise as a win-win strategy to solve energy and sanitation problems in slums settlements

Simon Kizito,Joseph Jjagwe,Bruno Ssewaya,Lillian Nekesa,Peter Tumutegyereize,Ahamada Zziwa,Allan John Komakech

DOI: https://doi.org/10.1016/j.wasman.2021.11.029

2022-03-01

Abstract:This study explored the production and evaluation of briquettes made from dried fecal sludge mixed with fresh food waste as a dual strategy to solve energy poverty and poor sanitation problems in Ugandan slums. Cylindrical briquettes measuring 82 mm height by 76 mm diameter were produced from dried fecal sludge (FS) alone, and FS mixed separately with pineapple peels (FS + PP), charcoal fines (FS + CD), and bean husks (FS + BH) in a mix ratio of 50% FS: 50% biomass (wt/wt basis) using red soil as the binder. Physiochemical characteristics and fuel thermal efficiency of the briquettes were tested following ASTM standards and were compared to wood-derived charcoal and commonly traded briquettes on market in Uganda. The average moisture content was 5.1%. Bulk density was highest in FS briquettes (1.12 g/cm3) and lowest in FS + BH (0.847 g/cm3). Volatile matter (VM) was highest in FS + PP (39%) and lowest in FS alone (25.7%). The average ash content was 30.4%. FS + PP had the highest calorific value (17.92 MJ/kg) while FS alone had the lowest (6.19 MJ/kg). The highest burning rate was recorded in FS + CD briquettes (8 g/min) and was lowest in FS + PP (4 g/min). Based on the calculated burning rates and calorific values, the economic advantage calculations implied that blending one ton of dry FS with one ton of dry pineapple peels for fuel briquettes, and their use as a substitute could save consumers about USD 620 per ton of wood charcoal foregone.
Electrical remodeling of the ventricular myocardium in myocarditis: studies of rat experimental autoimmune myocarditis.

J. Saito,S. Niwano,H. Niwano,T. Inomata,Y. Yumoto,Kazuko Ikeda,K. Inuo,Jisho Kojima,M. Horie,T. Izumi

DOI: https://doi.org/10.1253/CIRCJ.66.97

Circulation Journal

Abstract:The purpose of this study was to evaluate the electrical remodeling of the ventricular myocardium in the experimental autoimmune myocarditis (EAM) model in Lewis rats. EAM was induced by immunization with cardiac myosin. During the active myocarditis phase, the effective refractory period (ERP), the duration of the monophasic action potential (MAPD) was extracted from the left ventricular free wall, and the mRNA levels of Kv1.4, 4.2, 4.3 and L type Ca2+ channel were determined by RNase protection assays. The inducibility of ventricular arrhythmia was higher in EAM rats than in the control rat, and the direct relationship between the coupling intervals of the premature stimulus and the ventricular arrhythmia in EAM rats. The ERP was prolonged in EAM rats compared with the control group. The MAPDs determined as 20% and 90% repolarization time, were both longer in EAM rats than in the controls. The level of expression of Kv4.2 mRNA was reduced in EAM rats in comparison with the controls, whereas those of Kv1.4, 4.3 and the L type Ca2+ channel were unchanged. Ventricular vulnerability was higher in EAM rats than in the control rats, and some of the ventricular arrhythmias observed in the EAM group seemed to be based on triggered activity. The level of expression of Kv4.2 mRNA was significantly reduced, and this change was compatible with prolongation of the action potential duration.
Briquetting of black soldier fly frass as a post-harvest stabilization strategy

Rosemary M. Matheka,Simon M. Wandera,James M. Raude,Sylvia I. Murunga,Anthony Gachanja,Monica M. Ndolo

DOI: https://doi.org/10.2166/washdev.2024.249

2024-11-13

Journal of Water Sanitation and Hygiene for Development

Abstract:The production–consumption cycle needs a transition towards a circular economy where waste valorization is included. This study investigated briquetting as a stabilization method for black soldier fly frass (BSFF) with faecal matter, pig manure, and poultry manure as the larvae feed. Herein, dried BSFF was pyrolyzed at 350 °C for 2 h to produce biochar then mixed with charcoal dust in equal ratio to produce biobriquettes through densification, with cassava gel (10 wt%) as binder. One-way ANOVA showed statistical significance in carbon, nitrogen, hydrogen, and oxygen. There were significant differences (p < 0.05) between the calorific value, moisture content, ash content, volatile matter, and fixed carbon of the briquettes. The fixed carbon, volatile matter, moisture, and ash content ranged from 29.66 ± 0.86 to 42.01 ± 0.92, 29.26 ± 0.52 to 32.59 ± 0.80, 2.95 ± 0.1 to 5.08 ± 0.04, and 21.48 ± 0.14 to 37.20 ± 0.29, respectively. The calorific value of the produced briquettes ranged from 16.25 ± 0.57 to 20.70 ± 0.53 MJ/kg, which exceeds the minimum requirement of 14.5 MJ/kg recommended for non-woody briquettes. During combustion, concentrations of NOx, N2O, CO, and CO2 varied significantly across the treatments with the acacia charcoal having the highest concentration of CO. Briquetting is a potential stabilization method for frass resulting in waste reduction, bioenergy production, reduced adverse effects of climate change, and enhanced sustainability.

water resources
Characterizing biomass pellets produced from torrefied biowaste and waste medical plastic pyrolysis oil

Saravanan Ramalingam,S. Vijayaraj

DOI: https://doi.org/10.1007/s13399-023-04424-1

IF: 4.05

2023-06-05

Biomass Conversion and Biorefinery

Abstract:The saw-milling residues are biowaste generated during the sawing of logs into lumber, and they may be lucrative when turned into biowaste pellets. Using biowaste as a renewable fuel helps address the limited availability of fossil fuels, reduces pollution, and additionally decreases the need for landfill. This study investigated the thermal reaction kinetics and physical properties of oxidative torrefied sawdust (TSD) and waste medical plastic pyrolysis oil (WMPPO) blended pellets, TSD25 and TSD50, referring to 25% and 50% of WMPPO with TSD, respectively, using thermogravimetric analysis (TGA), whereas the pellets are prepared using a small-scale pellet processing system. The reported additional physicochemical properties like density, pellet durability index (PDI), moisture adsorption, and impact resistance (IR) were as per the American Society of Agricultural and Biological Engineers (ASABE) recommended tests for densified fuel pellets, proximate Fourier transform infrared spectroscopy (FTIR) were used for identifying the blend's chemical composition active constituents. Ultimate analysis was carried out for the elemental analysis, and the morphological study was conducted using scanning electron microscopy. The samples have a moisture content of less than 10%, a volatile matter content that seems to be 75 to 82%, and an ash content that seems to be 1.05 to 6.65%. Oxidative torrefied sawdust scanning electron micrographs reveal micro, macro, and meso pores and improved the Brunauer-Emmett-Teller (BET) surface area. FTIR and TGA validate the addition of 50% WMPPO with TSD-controlled combustion zone temperature with the activation energy of 27.63 kJ/mol for an effective thermal conversion process. The physicochemical properties of density, pellet durability index (PDI), moisture adsorption, and impact resistance (IR) for sawdust (SD), TSD, and TSD blends with WMPPO are also reported. Both low-temperature torrefaction and waste medical plastic pyrolysis oil blending reduce volatile loss and improve fuel pellet physicochemical and thermochemical characteristics.

energy & fuels,engineering, chemical
Pyrolysis of Plastics-Free Refuse Derived Fuel Derived from Municipal Solid Waste and Combustion of the Char Products in Lab and Pilot Scales: A Comparative Study

Minhui Guo,Kan Wang,Xiaohui Bing,Junrui Cheng,Ying Zhang,Xiangyi Sun,Baohong Guan,Jie Yu

DOI: https://doi.org/10.1016/j.fuel.2023.130335

IF: 7.4

2024-01-01

Fuel

Abstract:Pyrolysis of refuse derived fuel (RDF) has great potential for energy recovery from municipal solid waste (MSW), while chlorine-related plastics issue was one major barrier for scale up. After screening out plastics, the RDF pyrolysis and char products combustion were evaluated in lab and pilot scales. Thermogravimetry with Fourier transform infrared spectroscopy results suggest that the main RDF pyrolysis reaction occurred in 190-410 degrees C, involving decomposition, decarboxylation, demethylation, and dehydration reactions, with CO2, CH4, H2O, CO, and organic compounds as the main gaseous products. Impacts of temperature and residence time on char yield and proximate composition were evaluated in lab, and a lower temperature was favored. The pilot-scale char had a comparable proximate composition to the lab-scale ones, but a lower heating value, lower H/C ratio, higher O/ C ratio, which may due to different dominant reaction pathways during pyrolysis: apparent demethanation versus dehydration. Thermogravimetry data infers that the combustion performance of pilot-scale char, including combustion stage, weight loss, and kinetic parameters, were close to chars made in lab. Pilot-scale combustion tests show relief of flue gas pollution after upgrading RDF to char, while particulate matter and heavy metals were still main concerns. Lab-and pilot-scale investigations highlight scale up of plastics-free RDF pyrolysis and combustion as a promising and economic alternative for materials and energy recoveries from MSW.
Optimization of Briquette Fuels by Co-Torrefaction of Residual Biomass and Plastic Waste Using Response Surface Methodology

Shuai Guo,Lidong Liu,Deng Zhao,Chenchen Zhao,Xingcan Li,Guangyu Li

DOI: https://doi.org/10.3390/molecules28062568

IF: 4.6

2023-03-11

Molecules

Abstract:Combining biomass, a clean and renewable energy source, with waste plastic, which serves as a good auxiliary fuel, can produce high-quality clean fuel. The performance of biomass-derived fuel can be improved by torrefaction. This study optimized the co-torrefaction of fungus bran and polypropylene (PP) waste plastic to obtain clean solid biofuel with high calorific value and low ash content (AC) using response surface methodology. Two sets of mixed biochars were investigated using a multiobjective optimization method: mass yield–higher heating value–ash content (MY-HHV-AC) and energy yield–ash content (EY-AC). PP increased the heat value, decreased AC, and acted as a binder. The optimal operating conditions regarding reaction temperature, reaction time, and PP blending ratio were 230.68 °C, 30 min, and 20%, respectively, for the MY-HHV-AC set and 220 °C, 30 min, 20%, respectively, for the EY-AC set. The MY-HHV-AC set had properties close to those of peat and lignite. Furthermore, compared with that of the pure biochar, the AC of the two sets decreased by 15.71% and 14.88%, respectively, indicating that the prepared mixed biochars served as ideal biofuels. Finally, a circular economy framework for biobriquette fuel was proposed and prospects for preparing pellets provided.

chemistry, multidisciplinary,biochemistry & molecular biology
Quality assessment of briquettes derived from carbonized cassava peel and sawdust as sustainable domestic sources of energy in Oyo State, Nigeria

C. A. Ajagbe,M. F. Zainuddin,L. A. Manaf,N. N. R. N. A. Rahim,G. T. Anguruwa

DOI: https://doi.org/10.1080/17597269.2024.2420292

2024-11-10

Biofuels

Abstract:About 80% of Nigeria's rural and semi-urban population uses fuelwood, which accounts for 37% of the country's energy demand. This results in the annual loss of 350,000 to 400,000 hectares of forest, increased carbon emissions, and loss of biodiversity, affecting ecosystems and quality of life. Therefore, this study was conducted to evaluate the physicochemical and combustion properties of carbonized cassava peel (CP) and sawdust (SD) hybrid briquettes as an alternative to fuelwood. Factors considered were CP/SD ratios (100:0, 75:25, 50:50, 25:75, 0:100), binder concentrations (5 and 10 g), and residence times (10, 20, 30 min). The briquettes were produced by applying a low compaction pressure of 2.4 MPa. The briquettes exhibited densities of 320.00-627.79 kg/m3, moisture content of 4.37-8.22%, water resistances of 87.26-99.85%, ash content of 5.73-41.03%, calorific values of 20.01-32.30 KJ/kg, and carbon content of 55.25-57.07%, respectively. ANOVA and Duncan's multiple range tests revealed that CP/SD ratio is the most significant factor influencing the physicochemical and combustion properties of the briquettes. This study successfully showcased carbonized CP/SD briquettes as an alternative cooking fuel in Oyo State, leveraging the abundance of CP and SD and the feasibility of low-pressure compaction without costly equipment.

energy & fuels
Modeling and optimization of compaction pressure, binder percentage and retention time in the production process of carbonized sawdust-based biofuel briquettes using response surface methodology (RSM)

Junior Maimou Nganko,Ekoun Paul Magloire Koffi,Prosper Gbaha,Alpha Ousmane Toure,Moustapha Kane,Babacar Ndiaye,Mamadou Faye,Willy Magloire Nkounga,Claudine Tiogue Tekounegning,Echua Elisabeth Jasmine Bile,Kouassi Benjamin Yao

DOI: https://doi.org/10.1016/j.heliyon.2024.e25376

IF: 3.776

2024-02-01

Heliyon

Abstract:The importance of parameters such as compaction pressure, binder percentage and retention time and their interaction in the production of carbonized briquettes for domestic or industrial use cannot be overestimated, as they have a considerable impact on the properties of the resulting briquettes. This study used Box-Behnken Response Surface Methodology (RSM) and Analysis Of Variance (ANOVA) to show how the above parameters and their interactions significantly influence the Higher Heating Value (HHV), ash content and Impact Resistance Index (IRI) of the biofuels obtained. The briquettes are characterized in accordance with American Society for Testing and Materials ASTM D-(5865 and 3172). IRI is determined by the drop test. The Niton XLT900s X-ray fluorescence spectrometer is used for mineralogical analysis. The peel starch used as a binder is characterized by the Association of Official Agricultural Chemists standard. This starch has a starch purity of 89.8 %, an HHV of 13974 kJ/kg, a protein content of 4.79 % and a sugar content of 1.3 %. The HHV of the biofuels ranged from 23783 to 26050 kJ/kg, their ash content from 2.86 to 5.24 %, and the IRI from 136.36 to 500 %. The significant effect of binder on these results is confirmed (p < 0.05). The Standard deviations of ± 21.425 kJ/kg, ± 0.021 % and ± 2.121 % were obtained between the experimental values and those of the mathematical models developed to predict HHV, ash content and IRI. The optimum parameters for industrial biofuel production correspond to a binder percentage of 10 %, a compaction pressure of 75 kPa and a retention time of 7.49 min. The experimental results under these conditions are: 25596 kJ/kg, 3.01 % and 375 % for HHV, ash content and IRI. In correlation with the absence of certain heavy metals, the study confirms that the briquettes produced are suitable for domestic use.
MAKING BRIQUETTES FROM WASTE OF COCONUT SHELL AND PEANUT SHELL

Yusraida Khairani Dalimunthe,Sugiatmo Kasmungin,Eddy Sugiarto,Lisa Sugiarti,Alyssa Lagrama

DOI: https://doi.org/10.25105/urbanenvirotech.v4i2.7417

2021-04-06

INDONESIAN JOURNAL OF URBAN AND ENVIRONMENTAL TECHNOLOGY

Abstract:Aims: This study aimed to increase the utilization of biomass-derived from the waste of coconut and peanut shells by making them as briquettes, as an alternative to fuel. The scarcity of petroleum because of its increasingly limited existence encourages all parties to take part in the development and discovery of new alternative energies. This is expected to overcome one of the most important of the many problems facing this country. The method used in this research is to start with a literature study of materials from various sources about the benefits and manufacturing of briquettes from biomass waste as an alternative energy source to be further tested for quality. This involves a heat test, water content test, ash content test and determination of the flying matter. Results: The test results showed that natural gas emissions were below threshold, namely 0-30 ppm CO, 0-3.6 ppm H2S, and undetectable NOx. After evaluation, the results showed that with the addition of 30% of the biomass, the ignition time was reduced and the remaining unburned briquettes or bottom ash was reduced by 68.68%. Conclusion, significance, and impact of study: The results help the community and the parties involved related to appropriate bio briquettes technology. It also eventually becomes one of the solutions to assist the government in solving problems related to alternative fuels to petroleum.

English Else
Co-pyrolysis of plastic waste and eucalyptus waste wood for fuel pellets production: A study of fuel, mechanical, and combustion characteristics under varying binder proportion

Biswajit Samal,Hari Bhakta Sharma,Kumar Raja Vanapalli,Brajesh Kumar Dubey,Jayanta Bhattacharya

DOI: https://doi.org/10.1016/j.scitotenv.2024.173883

IF: 9.8

2024-06-17

The Science of The Total Environment

Abstract:The study explores the effect of varying molasses proportions as a binder on the characteristics of densified char obtained through the slow co -pyrolysis of plastic waste and Eucalyptus wood waste (Waste low-density polyethylene – Eucalyptus wood (WLDPE–EW) and Waste Polystyrene – Eucalyptus wood (WPS–EW)). Pyrolysis was conducted at 500 °C with a residence time of 120 min, employing plastic to wood waste ratios of 1:2 and 1:3 ( w / w ). The focus was on how varying the proportion of molasses (10–30 %), influences the physical and combustion properties of the resulting biofuel pellets. Our findings reveal that the calorific value of the pellets decreased from 28.94 to 27.44 MJ/Kg as the molasses content increased. However, this decrease in calorific value was compensated by an increase in pellet mass density, which led to a higher energy density overall. This phenomenon was attributed to the formation of solid bridges between particles, facilitated by molasses, effectively decreasing particle spacing. The structural integrity of the pellets, as measured by the impact resistance index, improved significantly (43–47 %) with the addition of molasses. However, a significant change in the combustion characteristics depicted by lower ignition and burnout temperatures were observed due to decrease in fixed carbon value and increase in volatile matter content, as the proportion of molasses increased. Despite these changes, the pellets demonstrated a stable combustion profile, suggesting that molasses are an effective binder for producing biofuel pellets through the densification of char derived from the co-pyrolysis of plastic and Eucalyptus wood waste. The optimized molasses concentration analyzed through multifactor regression analysis was 16.96 % with 28 % WLDPE proportion to produce WLDPE–EW char pellets. This study highlights the potential of using molasses as a sustainable binder to enhance the mechanical and combustion properties of biofuel pellets, offering a viable pathway for the valorization of waste materials.

environmental sciences
Utilization of LDPE Plastic Waste, Coconut Shell and Coconut Husk as Basic Material for Briquettes with Tapioca Starch Adhesive

Sheilla Rully Anggita,Renanda Fasha Devarasalya,Istikomah Istikomah,Ari Bawono

DOI: https://doi.org/10.25077/jif.15.2.81-90.2023

2023-04-29

JURNAL ILMU FISIKA | UNIVERSITAS ANDALAS

Abstract:Bio-briquettes of organic waste can be used as alternative energy to solve the waste problem. This study aimed to determine the quality of bio-briquettes made of LDPE, coconut husk, and coconut shell with tapioca adhesive. The coconut husk and shell were carbonized at 300 °C for 60 minutes. Charcoal that has been ground and sieved with 40 mesh is mixed with tapioca flour adhesive, and pieces of LDPE are added. Then, the sample is pressed with a cylindrical mold with a matrix strength of 5 tons. Bio-briquettes were dried in an oven at 80 °C for 12 hours. The quality of the briquette was evaluated through proximate analysis, including the calorific value, moisture content, ash content, volatile matter content, and fixed carbon content. The calorific value of all samples complied with the regulation of the Ministry of Energy and Mineral Resources (ESDM) No. 047 of 2006, which is above 4400 cal/g. The maximum moisture content is 15%, which fulfills SNI 06–3730-1995 standards, and the ESDM regulation, especially for the composition of 40% shell: 40% coconut: LDPE 20%. The ash content, volatile matter content, and fixed carbon content of all samples did not comply with SNI briquette standards and ESDM regulations.
Production of sawdust and chicken fat briquettes as an alternative solid fuel

Rodrigo Mazolini Imberti,Janine Carvalho Padilha,Leonardo da Silva Arrieche

DOI: https://doi.org/10.1016/j.renene.2024.120638

IF: 8.7

2024-05-22

Renewable Energy

Abstract:This study focuses on converting underutilized or discarded sawdust from Eucalyptus grandis (EG) and Pinus elliottii (PE), along with roasting chicken oil (RCO) and chicken visceral oil (CVO), into alternative briquettes. Employing heuristic methods and branch-and-bound techniques, 27 experiments were conducted based on a central composite design (CCD), including two central point repetitions. The energy density (ED) of the briquettes was evaluated immediately after production (EDi) and three months later (EDf). The higher heating value (HHV), thermogravimetric analysis (TGA) with its first derivative, and cost of each briquette were also characterized. Increasing chicken oil content improved HHV, initial ED, reduced ash content, and enhanced thermal degradation performance. However, exceeding 15% oil content caused wastage during pressing. Excessive CVO use is cost-prohibitive unless produced by the poultry industry. The optimal briquette was obtained in experiment 9 with 21.25% EG, 63.75% PE, 3.75% CVO, and 11.25% RCO by mass. Structural neighbors were identified based on this composition. Sawdust type and particle size had minimal impact on the results.

energy & fuels,green & sustainable science & technology
Utilization of Pine Fruit and Peanut Shell Wastes into Briquettes as an Alternative Fuel

Mohamad Mirwa,Muhammad Abdus Salam Jawwad

DOI: https://doi.org/10.1051/e3sconf/202132809002

2021-01-01

E3S Web of Conferences

Abstract:Fuel or energy sources scarcity is currently a problem in Indonesia. Pine waste and peanut shells are wastes that have potential to be processed into alternative energy as briquettes, using molasses as adhesive. Briquette was made by destroying the material into small pieces that have been carbonized and sieved with a variation of 20 and 30 mesh size, added with molasses, and then molded with a hydraulic press. Briquettes are dried using an oven at 105 °C for 10 hours to remove moisture content. The pine to peanut shell ratio used are of 0:1, 1:0, 1:1, 1:2, 1:3, 2:1, 2:3, 3:1 and 3:2. The analysis includes analysis of calorific value, moisture content, ash content and compressive strength. The result shows the pine waste to peanut shells ratio of 1:0 has the highest calorific value for 20 mesh is 4674.50 Cal/g and for 30 mesh is 4585.10 Cal/g. The lowest water content for 20 mesh is 1.76% and for 30 mesh is 1.85%. The lowest ash content for 20 mesh is 0.58% and for 30 mesh is 0.59%. And the highest compressive strength for 20 mesh is 35.20 kg/cm 2 and for 30 mesh is 28.90 kg/cm 2 .

English Else
Combustion properties improvement and economic evaluation of charcoal briquettes from mixed agricultural waste biomass

Ruamporn Nikhom,Kittiphoom Suppalakpanya,Suwattana Nikhom,Thathira Siriphan

DOI: https://doi.org/10.1007/s13399-024-05379-7

IF: 4.05

2024-02-11

Biomass Conversion and Biorefinery

Abstract:Agricultural waste biomass is one of the most abundant and readily available sources of solid biofuel production. However, to ensure sustainability, it is crucial that the obtained biofuel is energetically efficient. In this study, briquettes were produced from rice husk char (RHC) and crushed rubberwood charcoal (CRC) separately and in combination. RHC and CRC briquettes were respectively labeled RHC 10 and RHC 0 . Mixed biomass briquettes were produced at RHC–CRC mass ratios of 2:8 (RHC 2 ), 4:6 (RHC 4 ), 6:4 (RHC 6 ), and 8:2 (RHC 8 ). The combustion properties of the various briquettes were evaluated to determine potential enhancements, and the economic feasibility of production was evaluated. The addition of CRC enhanced the combustion properties of RHC, reducing ash content and increasing fixed carbon. The heating values of the mixed biomass briquettes were higher than the heating value of the RHC briquette. The RHC 0 , RHC 2 , and RHC 4 briquettes had heating values exceeding 5000 cal/g, meeting the national standards for charcoal briquettes. However, the economic feasibility study revealed that only RHC 0 and RHC 2 briquettes had a payback period of less than four years, with a positive net present value (NPV) and an internal rate of return (IRR) exceeding a bank interest rate of 7%. Therefore, RHC 0 and RHC 2 briquettes could be suitable and environmentally friendly alternative energy sources with favorable combustion properties.

energy & fuels,engineering, chemical
Development of solid waste utilization technology in coke furnaces

Vasyl A. Kravets,Victoria M. Mikheyenko

DOI: https://doi.org/10.32347/2411-4049.2022.1.44-55

2022-04-15

Environmental Safety and Natural Resources

Abstract:In industrial centers with coke oven and by-product production, it is advisable to use existing coke ovens for the processing of the organic part of waste. At the same time, sanitary and environmental problems are solved, and the load of production capacities of the coke oven and by-chemical industry is ensured in a crisis. The target of the work is to develop the basics of technology for the use of plastic waste and coke dust in the coke oven process. In laboratory conditions, two variants of the technology of briquetting coke dust with plastic from household waste were developed. In the first version, briquettes were produced by singling a mixture of coke dust with crushed PET bottles, polystyrene and PCB products and polyethylene films at a temperature of about 220 °C. But the briquettes obtained by this method were mechanically not durable, which did not provide requirements for transportation on the conveyor. In the second version, briquettes were produced by cold pressing a mixture of coke dust with withering plastic solution in coke solvent. Such briquettes turned out to be mechanically durable, they were made about 5 kg, and industrial coking was carried out by the use of the be agree method by loading into the third hatch of the battery No. 2 of the Makeevka Coke and Chemical Plant. Coke obtained as a result of an industrial experiment of coke from the charge with the addition of briquettes was investigated according to standard methods. It was established that prior to giving 3–5% of briquettes in the coke hate, coke is possible to obtain an economical effect due to coal savings.
Ignition, Combustion, and Mechanical Properties of Briquettes from Coal Slime and Oil Waste, Biomass, Peat and Starch

Ksenia Vershinina,Vadim Dorokhov,Daniil Romanov,Pavel Strizhak

DOI: https://doi.org/10.1007/s12649-022-01883-x

2023-01-31

Waste and Biomass Valorization

Abstract:The paper discusses the mechanical properties of waste-derived briquettes, their ignition and combustion behavior, and emissions. The briquettes based on coal slime blended with straw/peat/sawdust/waste compressor oil were used. 100% Coal slime and 100% biomass briquettes were reference cases. The proportion of coal slime in the multi-component briquettes was at least 85%. The samples were tested on a laboratory scale. Briquettes based on coal slime and used oil were characterized by moisture resistance and high energy performance indicator, yet they were brittle. Starch improved their impact resistance considerably. However, when added to mixtures of coal slime and straw, starch led to greater destruction of initially rather strong briquettes. The addition of starch slightly increased the water absorption characteristics of all the samples during storage. The ignition temperatures of briquettes of different compositions ranged from 350 to 610 °C. The briquette ignition characteristics tended to worsen when starch was added. A multi-criteria evaluation of fuels, considering cost, ignition, combustion behavior and emissions, as well as mechanical properties, showed that the highest efficiency is typical of 100% sawdust briquettes. For the fossil fuel briquettes, the best synergistic effect resulted from the combination of 90% coal slime and 10% straw. The "coal slime-peat-starch" is an undesirable combination, because it reduces the efficiency indicators for all the categories considered and makes the fuel more expensive.

environmental sciences
Optimizing Waste for Energy: Exploring Municipal Solid Waste Variations on Torrefaction and Biochar Production

Ibrahim Luqman Mpungu,Obadiah Maube,Patrick Nziu,Josphat Igadwa Mwasiagi,Benson Dulo,Ocident Bongomin

DOI: https://doi.org/10.1155/2024/4311062

IF: 4.6

2024-08-19

International Journal of Energy Research

Abstract:Energy primarily comes from fossil fuels, which leads to environmental deterioration through increased carbon dioxide load and other greenhouse gases in the atmosphere. Renewable energy is a cheap alternative, and biomass, like municipal solid wastes (MSWs), can be suitably used for energy production. This paper reviews the impact of variations in MSW composition on its physical, chemical, and lignocellulosic properties. It further illustrates how these properties affect torrefaction products. It was observed that MSW can refer to either a combination of different waste types or independent wastes; hence, there is no standard composition of MSW. The variations in composition are responsible for fluctuating physical, chemical, and lignocellulosic properties. These properties, along with torrefaction process parameters, simultaneously affect the torrefied product, whereas lignocellulosic properties influence the biochar yield, and physical and chemical properties impact calorific value and ash content. Torrefying MSW containing low moisture content yields biochar with a high calorific value. Methods to improve the lignocellulosic properties of MSW have not been studied. Research is needed to assess the possibility of improving biochar yields in MSW by enhancing lignin percentages, possibly through blending MSW. A guide on the best blend combinations and ratios is required. Also, it is crucial to study optimal torrefaction process parameters.

energy & fuels,nuclear science & technology
Production and characterization of coconut shell charcoal-based bio-briquettes as an alternative energy source for rural communities

John Yirijor,Alice Abigail Tatenda Bere

DOI: https://doi.org/10.1016/j.heliyon.2024.e35717

IF: 3.776

2024-08-09

Heliyon

Abstract:The increasing demand for sustainable energy solutions has driven interest in the utilization of agricultural residues, such as coconut shells, for bio-briquette production. This study investigates the impact of binder types (cassava and corn) and concentrations (5 wt%, 10 wt%, 15 wt%) on the properties of bio-briquettes made from dried coconut shells with two particle sizes (40 mesh and 60 mesh). The experimental evaluation focuses on several performance indicators, including density, shatter index, percentage moisture content (PMC), percentage volatile matter (PVM), percentage ash content (PAC), percentage fixed carbon (PFC), higher heating value (HHV), ignition time, burning time, and boiling time. The results indicate that briquettes with 10 % fine charcoal cassava binder achieved the highest density of 0.764 g/cm³ due to improved compaction. Briquettes with 15 % coarse charcoal corn binder demonstrated the highest shatter resistance at 96.99 %, reflecting their superior structural integrity. The highest PMC and PVM values were observed in briquettes with 15 % coarse charcoal cassava binder, at 8.13 % and 31.25 %, respectively. Conversely, the highest PAC was 16.34 % for 5 % coarse charcoal cassava binder. Briquettes with 10 % fine charcoal corn binder exhibited the highest PFC of 70.79 % and HHV of 31.51 MJ/kg. Boiling times ranged from 15 min 53 s to 36 min 35 s, with the shortest boiling time for briquettes with 10 % fine charcoal corn binder. The findings highlight the superior mechanical properties and energy performance of bio-briquettes with specific binder concentrations and particle sizes. This study demonstrates the potential of coconut shell bio-briquettes as a viable and sustainable energy source, offering economic and environmental benefits through the effective utilization of agricultural waste and reduction of carbon emissions.

Mechanisms of calcium release in sarcoplasmic reticulum.

Valorization and optimization of Prosopis africana pod and cowpea husk wastes for densified hybrid briquette production

Processing and properties of a solid energy fuel from municipal solid waste (MSW) and recycled plastics

Biofuel characteristics of non-charred briquettes from dried fecal sludge blended with food market waste: Suggesting a waste-to-biofuel enterprise as a win-win strategy to solve energy and sanitation problems in slums settlements

Electrical remodeling of the ventricular myocardium in myocarditis: studies of rat experimental autoimmune myocarditis.

Briquetting of black soldier fly frass as a post-harvest stabilization strategy

Characterizing biomass pellets produced from torrefied biowaste and waste medical plastic pyrolysis oil

Pyrolysis of Plastics-Free Refuse Derived Fuel Derived from Municipal Solid Waste and Combustion of the Char Products in Lab and Pilot Scales: A Comparative Study

Optimization of Briquette Fuels by Co-Torrefaction of Residual Biomass and Plastic Waste Using Response Surface Methodology

Quality assessment of briquettes derived from carbonized cassava peel and sawdust as sustainable domestic sources of energy in Oyo State, Nigeria

Modeling and optimization of compaction pressure, binder percentage and retention time in the production process of carbonized sawdust-based biofuel briquettes using response surface methodology (RSM)

MAKING BRIQUETTES FROM WASTE OF COCONUT SHELL AND PEANUT SHELL

Co-pyrolysis of plastic waste and eucalyptus waste wood for fuel pellets production: A study of fuel, mechanical, and combustion characteristics under varying binder proportion

Utilization of LDPE Plastic Waste, Coconut Shell and Coconut Husk as Basic Material for Briquettes with Tapioca Starch Adhesive

Production of sawdust and chicken fat briquettes as an alternative solid fuel

Utilization of Pine Fruit and Peanut Shell Wastes into Briquettes as an Alternative Fuel

Combustion properties improvement and economic evaluation of charcoal briquettes from mixed agricultural waste biomass

Development of solid waste utilization technology in coke furnaces

Ignition, Combustion, and Mechanical Properties of Briquettes from Coal Slime and Oil Waste, Biomass, Peat and Starch

Optimizing Waste for Energy: Exploring Municipal Solid Waste Variations on Torrefaction and Biochar Production

Production and characterization of coconut shell charcoal-based bio-briquettes as an alternative energy source for rural communities