Das Geschlechtsverhältnis der ehelichen und unehelichen Lebend- und Totgeburten im Kriege

W. Ludwig,C. Boost

DOI: https://doi.org/10.1007/BF02249945

1941-08-01

Zeitschrift für Kinderheilkunde

Abstract:

What problem does this paper attempt to address?

Nanofibrous polyelectrolyte complex incorporated BSA-alginate composite bioink for 3D bioprinting of bone mimicking constructs

Shreya Chrungoo,Tanmay Bharadwaj,Devendra Verma

DOI: https://doi.org/10.1016/j.ijbiomac.2024.131123

IF: 8.2

2024-03-30

International Journal of Biological Macromolecules

Abstract:Although several bioinks have been developed for 3D bioprinting applications, the lack of optimal printability, mechanical properties, and adequate cell response has limited their practical applicability. Therefore, this work reports the development of a composite bioink consisting of bovine serum albumin (BSA), alginate, and self-assembled nanofibrous polyelectrolyte complex aggregates of gelatin and chitosan (PEC-GC). The nanofibrous PEC-GC aggregates were prepared and incorporated into the bioink in varying concentrations (0 % to 3 %). The bioink samples were bioprinted and crosslinked post-printing by calcium chloride. The average nanofiber diameter of PEC-GC was 62 ± 15 nm. It was demonstrated that PEC-GC improves the printability and cellular adhesion of the developed bioink and modulates the swelling ratio, degradation rate, and mechanical properties of the fabricated scaffold. The in vitro results revealed that the bioink with 2 % PEC-GC had the best post-printing cell viability of the encapsulated MG63 osteosarcoma cells and well oragnized stress fibers, indicating enhanced cell adhesion. The cell viability was >90 %, as observed from the MTT assay. The composite bioink also showed osteogenic potential, as confirmed by the estimation of alkaline phosphatase activity and collagen synthesis assay. This study successfully fabricated a high-shape fidelity bioink with potential in bone tissue engineering.

polymer science,biochemistry & molecular biology,chemistry, applied
Composite bioink incorporating cell-laden liver decellularized extracellular matrix for bioprinting of scaffolds for bone tissue engineering

Pengyue You,Hang Sun,Haotian Chen,Changcan Li,Yilei Mao,Tao Zhang,Huayu Yang,Haitao Dong

DOI: https://doi.org/10.1016/j.bioadv.2024.214017

2024-08-30

Abstract:The field of bone tissue engineering (BTE) has witnessed a revolutionary breakthrough with the advent of three-dimensional (3D) bioprinting technology, which is considered an ideal choice for constructing scaffolds for bone regeneration. The key to realizing scaffold biofunctions is the selection and design of an appropriate bioink, and existing bioinks have significant limitations. In this study, a composite bioink based on natural polymers (gelatin and alginate) and liver decellularized extracellular matrix (LdECM) was developed and used to fabricate scaffolds for BTE using 3D bioprinting. Through in vitro studies, the concentration of LdECM incorporated into the bioink was optimized to achieve printability and stability and to improve the proliferation and osteogenic differentiation of loaded rat bone mesenchymal stem cells (rBMSCs). Furthermore, in vivo experiments were conducted using a Sprague Dawley rat model of critical-sized calvarial defects. The proposed rBMSC-laden LdECM-gelatin-alginate scaffold, bioprinted layer-by-layer, was implanted in the rat calvarial defect and the development of new bone growth was studied for four weeks. The findings showed that the proposed bioactive scaffolds facilitated angiogenesis and osteogenesis at the defect site. The findings of this study suggest that the developed rBMSC-laden LdECM-gelatin-alginate bioink has great potential for clinical translation and application in solving bone regeneration problems.
3D printing of PCL-ceramic composite scaffolds for bone tissue engineering applications

Santosh Kumar Parupelli,Sheikh Saudi,Narayan Bhattarai,Salil Desai

DOI: https://doi.org/10.36922/ijb.0196

2023-07-05

International Journal of Bioprinting

Abstract:Three-dimensional (3D) printing was utilized for the fabrication of a composite scaffold of poly(ε-caprolactone) (PCL) and calcium magnesium phosphate (CMP) bioceramics for bone tissue engineering application. Four groups of scaffolds, that is, PMC-0, PMC-5, PMC-10, and PMC-15, were fabricated using a custom 3D printer. Rheology analysis, surface morphology, and wettability of the scaffolds were characterized. The PMC-0 scaffolds displayed a smoother surface texture and an increase in the ceramic content of the composite scaffolds exhibited a rougher structure. The hydrophilicity of the composite scaffold was significantly enhanced compared to the control PMC-0. The effect of ceramic content on the bioactivity of fibroblast NIH/3T3 cells in the composite scaffold was investigated. Cell viability and toxicity studies were evaluated by comparing results from lactate dehydrogenase (LDH) and Alamar Blue (AB) colorimetric assays, respectively. The live-dead cell assay illustrated the biocompatibility of the tested samples with more than 100% of live cells on day 3 compared to the control one. The LDH release indicated that the composite scaffolds improved cell attachment and proliferation. In this research, the fabrication of a customized composite 3D scaffold not only mimics the rough textured architecture, porosity, and chemical composition of natural bone tissue matrices but also serves as a source for soluble ions of calcium and magnesium that are favorable for bone cells to grow. These 3D-printed scaffolds thus provide a desirable microenvironment to facilitate biomineralization and could be a new effective approach for preparing constructs suitable for bone tissue engineering.

engineering, biomedical,materials science, biomaterials
Printing bone in a gel: using nanocomposite bioink to print functionalised bone scaffolds

G Cidonio,M Cooke,M Glinka,J I Dawson,L Grover,R O C Oreffo

DOI: https://doi.org/10.1016/j.mtbio.2019.100028

Abstract:Free-form printing offers a novel biofabrication approach to generate complex shapes by depositing hydrogel materials within a temporary supportive environment. However, printed hydrogels typically lack the requisite mechanical properties and functionality of the desired tissue, limiting application and, more importantly, safety and efficacy of the implant. The study authors have developed an innovative nanoclay-based bioink to print high shape fidelity functional constructs for potential skeletal application. Laponite® (LAP) nanoclay was combined with gellan gum (GG) to generate a printable hydrogel that was highly stable in vitro, displayed limited swelling ability compared with the silicate-free control and remained stable over time. An agarose fluid gel was found to provide the requisite support for the deposition of the material ink and preservation of the printed structure before crosslinking. Printed C2C12 myoblasts remained viable and displayed extensive proliferation over 21 days in culture. Cell-laden scaffolds demonstrated functionality within 1 day of culture in vitro and that was preserved over 3 weeks. Analysis of absorption and release mechanisms from LAP-GG using model proteins (lysozyme and bovine serum albumin) demonstrated the retention capability of the clay-based materials for compound localisation and absence of burst release. Vascular endothelial growth factor was loaded within the agarose fluid gel and absorbed by the material ink via absorption during deposition. The 3D-printed constructs were implanted on the chorioallantoic membrane of a 10-day-old developing chick. Extensive and preferential vasculature infiltration was observed in LAP-GG-loaded vascular endothelial growth factor constructs compared with controls (p<0.01 and p<0.0001) after only 7 days of incubation. The current studies demonstrate, for the first time, the application of innovative LAP-GG 3D constructs in the generation of growth factor-loaded 3D constructs for potential application in skeletal tissue repair.
Desktop-Stereolithography 3D Printing of a Polyporous Extracellular Matrix Bioink for Bone Defect Regeneration

Yunxiang Luo,Hao Pan,Jiuzhou Jiang,Chenchen Zhao,Jianfeng Zhang,Pengfei Chen,Xianfeng Lin,Shunwu Fan

DOI: https://doi.org/10.3389/fbioe.2020.589094

IF: 5.7

2020-11-06

Frontiers in Bioengineering and Biotechnology

Abstract:Introduction: Decellularized tendon extracellular matrix (tECM) perfectly provides the natural environment and holds great potential for bone regeneration in Bone tissue engineering (BTE) area. However, its densifying fiber structure leads to reduced cell permeability. Our study aimed to combine tECM with polyethylene glycol diacrylate (PEGDA) to form a biological scaffold with appropriate porosity and strength using stereolithography (SLA) technology for bone defect repair.Methods: The tECM was produced and evaluated. Mesenchymal stem cell (MSC) was used to evaluate the biocompatibility of PEGDA/tECM bioink in vitro. Mineralization ability of the bioink was also evaluated in vitro. After preparing 3D printed polyporous PEGDA/tECM scaffolds (3D-pPES) via SLA, the calvarial defect generation capacity of 3D-pPES was assessed.Results: The tECM was obtained and the decellularized effect was confirmed. The tECM increased the swelling ratio and porosity of PEGDA bioink, both cellular proliferation and biomineralization in vitro of the bioink were significantly optimized. The 3D-pPES was fabricated. Compared to the control group, increased cell migration efficiency, up-regulation of osteogenic differentiation RNA level, and better calvarial defect repair in rat of the 3D-pPES group were observed.Conclusion: This study demonstrates that the 3D-pPES may be a promising strategy for bone defect treatment.

multidisciplinary sciences
Multimaterial coextrusion (bio)printing of composite polymer biomaterial ink and hydrogel bioink for tissue fabrication

Isabella C.P. Rodrigues,Luis C. O.Clark,Xiao Kuang,Regina Sanchez,Éder S.N. Lopes,Laís P. Gabriel,Yu Shrike Zhang

DOI: https://doi.org/10.1016/j.compositesb.2024.111337

IF: 11.322

2024-02-24

Composites Part B Engineering

Abstract:Bone tissue engineering strategies face considerable challenges owing to the complexity of the bone. This study introduces an unconventional method based on multimaterial 3D coextrusion-(bio)printing to address some of these challenges. The strategy enables simultaneous (bio)printing of a poly(lactic-co-glycolic acid)-based polymer ink laden with hydroxyapatite and a gelatin methacryloyl (GelMA)-based hydrogel bioink containing mesenchymal stem cells (MSCs). The resulting composite scaffolds exhibited a trabecular bone-like porosity and favorable compressive properties, surpassing those of GelMA alone. The (bio)printed MSCs demonstrated favorable viability, proliferation, morphology, and differentiation. This converged approach in multimaterial (bio)printing has the potential to transform the field of bone tissue engineering, offering a more efficient and effective way to regenerate skeletal tissues.

engineering, multidisciplinary,materials science, composites
Development of cell-laden photopolymerized constructs with bioactive amorphous calcium magnesium phosphate for bone tissue regeneration via 3D bioprinting

Ju Yeon Kim,Shrestha Bishnu Kumar,Chan Hee Park,Cheol Sang Kim

DOI: https://doi.org/10.1016/j.ijbiomac.2024.131412

IF: 8.2

2024-04-20

International Journal of Biological Macromolecules

Abstract:The synthesis of ideal bioceramics to guide the fate of cells and subsequent bone regeneration within the chemical, biological, and physical microenvironment is a challenging long-term task. This study developed amorphous calcium magnesium phosphate (ACMP) bioceramics via a simple co-precipitation method. The role of Mg 2+ in the formation of ACMP is investigated using physicochemical and biological characterization at different Ca/Mg molar ratio of the initial reaction solution. Additionally, ACMP bioceramics show superior cytocompatibility and improved osteogenic differentiation of co-cultured MC3T3-E1 cells. Regulation of the microenvironment with Mg 2+ can promote early-stage bone regeneration. For this, bioprinting technology is employed to prepare ACMP-modified 3D porous structures. Our hypothesis is that the incorporation of ACMP into methacrylated gelatin (GelMA) bioink can trigger the osteogenic differentiation of encapsulated preosteoblast and stimulate bone regeneration. The cell-laden ACMP composite structures display stable printability and superior cell viability and cell proliferation. Also, constructs loading the appropriate amount of ACMP bioceramic showed significant osteogenic differentiation activity compared to the pure GelMA. We demonstrate that the dissolved Mg 2+ cation microenvironment in ACMP-modified composite constructs plays an effective biochemical role, and can regulate cell fate. Our results predict that GelMA/ACMP bioink has significant potential in patient-specific bone tissue regeneration.

polymer science,biochemistry & molecular biology,chemistry, applied
3D Bioprinting of shear-thinning hybrid bioinks with excellent bioactivity derived from gellan/alginate and thixotropic magnesium phosphate-based gels

You Chen,Xiong Xiong,Xin Liu,Rongwei Cui,Chen Wang,Guoru Zhao,Wei Zhi,Mengjie Lu,Ke Duan,Jie Weng,Shuxin Qu,Jianhua Ge

DOI: https://doi.org/10.1039/d0tb00060d

2020-07-07

Abstract:3D Bioprinting is expected to become a strong tool for regenerative medicine, but satisfactory bioinks for the printing of constructs containing living cells are lacking due to the rigorous requirement of high printability and biocompatibility, which are often contradictory. Here, we have reported the development of a novel hybrid bioink by combining rigid gellan gum (GG), flexible sodium alginate (SA), and a bioactive substance thixotropic magnesium phosphate-based gel (TMP-BG). The ratio of these components was first optimized to obtain satisfactory gelating, mechanical, rheological, and printing properties. The formulated hybrid GG-SA/TMP-BG bioink had a good printability due to the shear-thinning and its multiple cross-linking by Mg2+ and Ca2+. The tunable mechanical performance of the hybrid bioink could simulate various extracellular matrices of the different tissues and support integrity of 3D printing constructs. Moreover, the hybrid bioink induced apatite deposition during immersion in simulated body fluids, and also promoted cell proliferation in vitro. MG-63 osteosarcoma cells were dispersed in the bioink and printed into 3D constructs. The cells exhibited good cell survival due to the shear-thinning property of the bioink and the ion concentration used for cross-linking. The proliferation rate of the cells also significantly exceeded those in non-printed samples. Confocal microscopy revealed a homogeneous distribution of cells in the printed constructs, and survival for more than 7 d. In vivo animal experiments showed that the hybrid bioink without cells could induce osteochondral repair. Therefore, this hybrid bioink has good printability, biocompatibility, mechanical support, and bioactivity, which is expected to have promising applications in 3D bioprinting.
Construction of 3D bioprinting of HAP/collagen scaffold in gelation bath for bone tissue engineering

Chuang Guo,Jiacheng Wu,Yiming Zeng,Hong Li

DOI: https://doi.org/10.1093/rb/rbad067

2023-01-01

Regenerative Biomaterials

Abstract:Abstract Reconstruction of bone defects remains a clinical challenge, and 3D bioprinting is a fabrication technology to treat it via tissue engineering. Collagen is currently the most popular cell scaffold for tissue engineering; however, a shortage of printability and low mechanical strength limited its application via 3D bioprinting. In the study, aiding with a gelatin support bath, a collagen-based scaffold was fabricated via 3D printing, where hydroxyapatite (HAP) and bone marrow mesenchymal stem cells (BMSCs) were added to mimic the composition of bone. The results showed that the blend of HAP and collagen showed suitable rheological performance for 3D extrusion printing and enhanced the composite scaffold’s strength. The gelatin support bath could effectively support the HAP/collagen scaffold’s dimension with designed patterns at room temperature. BMSCs in/on the scaffold kept living and proliferating, and there was a high alkaline phosphate expression. The printed collagen-based scaffold with biocompatibility, mechanical properties and bioactivity provides a new way for bone tissue engineering via 3D bioprinting.

materials science, biomaterials
Some experimental results in adaptive prediction DPCM coding of images

I. Paul,J. Woods

DOI: https://doi.org/10.1109/ICASSP.1983.1172002

1983-04-01

Abstract:In this paper we present results from our work on adaptive prediction dpcm for grey level images using the doubly stochastic Gaussian image model. This model consists of a lower level level 2-D Markov chain which takes on L different values and correspondingly L different sets of predictor parameters for an upper level conditionally Gaussian field. A simple gradient based algorithm which uses fuzzy decision theory is used to identify the lower level chain from observations on the upper level field, i.e. the actual image. The upper level field is encoded by 2-D DPCM using spatially varying predictors as determined by the lower level chain. For our simulations L was chosen to be 5, with 4 models representing edges at 0, 45, 90, and 135 degrees and the fifth model representing the non-edge regions. Both fixed and adaptive (Jayant type) quantizers were used. Greater compression is achieved by subsampling in the non-edge regions of the image and then interpolating at the decoder.
Proceedings of the Twenty-Ninth Annual ACM-SIAM Symposium on Discrete Algorithms, SODA 2018, New Orleans, LA, USA, January 7-10, 2018

A. Czumaj

DOI: https://doi.org/10.1137/1.9781611975031

Abstract:
3D bioprinting of mechanically tuned bioinks derived from cardiac decellularized extracellular matrix

Yu Jung Shin,Ryan T Shafranek,Jonathan H Tsui,Jelisha Walcott,Alshakim Nelson,Deok-Ho Kim

DOI: https://doi.org/10.1016/j.actbio.2020.11.006

2021-01-01

Abstract:3D bioprinting is a powerful technique for engineering tissues used to study cell behavior and tissue properties in vitro. With the right formulation and printing parameters, bioinks can provide native biological and mechanical cues while allowing for versatile 3D structures that recapitulate tissue-level organization. Bio-based materials that support cellular adhesion, differentiation, and proliferation - including gelatin, collagen, hyaluronic acid, and alginate - have been successfully used as bioinks. In particular, decellularized extracellular matrix (dECM) has become a promising material with the unique ability to maintain both biochemical and topographical micro-environments of native tissues. However, dECM has shown technical limitations for 3D printing (3DP) applications posed by its intrinsically low mechanical stability. Herein, we report hydrogel bioinks composed of partially digested, porcine cardiac decellularized extracellular matrix (cdECM), Laponite-XLG nanoclay, and poly(ethylene glycol)-diacrylate (PEG-DA). The Laponite facilitated extrusion-based 3DP, while PEG-DA enabled photo-polymerization after printing. Improving upon previously reported bioinks derived from dECM, our bioinks combine extrudability, shape fidelity, rapid cross-linking, and cytocompatibility in a single formulation (> 97% viability of encapsulated human cardiac fibroblasts and > 94% viability of human induced pluripotent stem cell derived cardiomyocytes after 7 days). The compressive modulus of the cured hydrogel bioinks was tunable from 13.4-89 kPa by changing the concentration of PEG-DA in the bioink formulation. Importantly, this span of mechanical stiffness encompasses ranges of tissue stiffness from healthy (compressive modulus ~5-15 kPa) to fibrotic (compressive modulus ~30-100 kPa) cardiac tissue states. The printed constructs demonstrated shape fidelity, adaptability to different printing conditions, and high cell viability following extrusion and photo-polymerization, highlighting the potential for applications in modeling both healthy and fibrotic cardiac tissue.
3D printing of hybrid biomaterials for bone tissue engineering: Calcium-polyphosphate microparticles encapsulated by polycaprolactone

Meik Neufurth,Xiaohong Wang,Shunfeng Wang,Renate Steffen,Maximilian Ackermann,Natalie D. Haep,Heinz C. Schröder,Werner E.G. Müller

DOI: https://doi.org/10.1016/j.actbio.2017.09.031

IF: 10.633

2017-01-01

Acta Biomaterialia

Abstract:Here we describe the formulation of a morphogenetically active bio-ink consisting of amorphous microparticles (MP) prepared from Ca2+ and the physiological inorganic polymer, polyphosphate (polyP). Those MP had been fortified by mixing with poly-ε-caprolactone (PCL) to allow 3D-bioprinting. The resulting granular PCL/Ca-polyP-MP hybrid material, liquefied by short-time heating to 100 °C, was used for the 3D-printing of tissue-like scaffolds formed by strands with a thickness of 400 µm and a stacked architecture leaving ≈0.5 mm2-sized open holes enabling cell migration. The printed composite scaffold turned out to combine suitable biomechanical properties (Young’s modulus of 1.60 ± 0.1 GPa; Martens hardness of 153 ± 28 MPa), matching those of cortical and trabecular bone, with morphogenetic activity. This scaffold was capable of attracting and promoting the growth of human bone-related SaOS-2 cells as demonstrated by staining for cell viability (Calcein AM), cell density (DRAQ5) and SEM studies. Furthermore, the hybrid material was demonstrated to upregulate the steady-state-expression of the cell migration-inducing chemokine SDF-1α. EDX analysis and FTIR measurements revealed the presence of hydroxyapatite in the mineral deposits formed on the scaffold surface. Based on the results we conclude that granular PCL/Ca-polyP-MP hybrid material is suitable for the fabrication of bioprintable scaffold which comprises not only biomechanical stability but also morphogenetic potential.
Suitability of Gelatin Methacrylate and Hydroxyapatite Hydrogels for 3D-Bioprinted Bone Tissue

Paul Stolarov,Jonathan de Vries,Sean Stapleton,Lauren Morris,Kari Martyniak,Thomas J. Kean

DOI: https://doi.org/10.3390/ma17051218

IF: 3.4

2024-03-07

Materials

Abstract:Background: Complex bone defects are challenging to treat. Autografting is the gold standard for regenerating bone defects; however, its limitations include donor-site morbidity and increased surgical complexity. Advancements in 3D bioprinting (3DBP) offer a promising alternative for viable bone grafts. In this experiment, gels composed of varying levels of gelatin methacrylate (GelMA) and hydroxyapatite (HA) and gelatin concentrations are explored. The objective was to increase the hydroxyapatite content and find the upper limit before the printability was compromised and determine its effect on the mechanical properties and cell viability. Methods: Design of Experiments (DoE) was used to design 13 hydrogel bioinks of various GelMA/HA concentrations. These bioinks were assessed in terms of their pipettability and equilibrium modulus. An optimal bioink was designed using the DoE data to produce the greatest stiffness while still being pipettable. Three bioinks, one with the DoE-designed maximal stiffness, one with the experimentally defined maximal stiffness, and a literature-based control, were then printed using a 3D bioprinter and assessed for print fidelity. The resulting hydrogels were combined with human bone-marrow-derived mesenchymal stromal cells (hMSCs) and evaluated for cell viability. Results: The DoE ANOVA analysis indicated that the augmented three-level factorial design model used was a good fit (p 0.05). There was, however, a significantly lower cell viability in the gel composed of 12.3% GelMA, 15.7% HA, and 2% gelatin compared to the other gels with a lower HA concentration (p < 0.05), showing that a higher HA content or print pressure may be cytotoxic within hydrogels. Conclusions: Extrusion-based 3DBP offers significant advantages for bone–tissue implants due to its high customizability. This study demonstrates that it is possible to create printable bone-like grafts from GelMA and HA with an increased HA content, favorable mechanical properties (145 kPa), and a greater than 80% cell viability.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
3D bioprinting by reinforced bioink based on photocurable interpenetrating networks for cartilage tissue engineering

Jingjie Shen,Wenjing Song,Jia Liu,Xiaoyun Peng,Zhuhao Tan,Yingni Xu,Sa Liu,Li Ren

DOI: https://doi.org/10.1016/j.ijbiomac.2023.127671

IF: 8.2

2023-11-06

International Journal of Biological Macromolecules

Abstract:Cartilage has a limited ability to repair itself, highlighting the urgent need for suitable materials for cartilage regeneration. Achieving a balance between cell survival environment and hydrogel crosslinking density is crucial for photosensitive cell-laden cartilage repair materials to achieve both high strength and good cell viability. Here, an interpenetrating hydrogel consisted of methacrylate gelatin (GelMA) and glycidyl methacrylate silk fibroin (SG) was introduced. Compared to GelMA hydrogel, GelMA/SG had desired mechanical properties, with achieving up to 5 times of compression modulus and 6 times of compression failure energy. Meanwhile, the chondrocytes inside GelMA/SG exhibited great viability which was over 90 %. GelMA/SG as a bioink had favorable printability for digital light processing (DLP) bioprinting. The mesh DLP-printed scaffolds with high precision were created and GelMA/SG had a better shape retention ability than GelMA. Moreover, GelMA/SG cell-laden scaffolds had high strength while chondrocytes proliferated significantly in vitro culture. They were implanted under the skin of nude mice to evaluate ectopic chondrogenesis in vivo . The GelMA/SG cell-laden scaffolds indicated little deformation and high expression of collagen type II and glycosaminoglycans, which was advantageous for cartilage regeneration. The scaffold and its fabrication strategy provide potential solutions for clinical cartilage repair problems in the future.

polymer science,biochemistry & molecular biology,chemistry, applied
Expression and function of two nicotinic subunits in insect neurons.

A. Vermehren,B. Trimmer

DOI: https://doi.org/10.1002/NEU.20088

2005-02-15

Journal of Neurobiology

Abstract:Nicotinic acetylcholine receptors (nAChRs) in insects are neuron-specific oligomeric proteins essential for the central transmission of sensory information. Little is known about their subunit composition because it is difficult to express functional insect nAChRs in heterologous systems. As an alternative approach we have examined the native expression of two subunits in neurons of the nicotinic-resistant, tobacco-feeding insect Manduca sexta. Both the alpha-subunit MARA1 and the beta-subunit MARB can be detected by in situ hybridization in the majority of cultured neurons with an overlapping, but not identical, distribution. Changes in intracellular Ca(2+) evoked by nicotinic stimulation are more strongly correlated to the expression of MARA1 than MARB and are independent of cell size. Unlike the previously reported critical role of MARA1 in mediating nicotinic Ca(2+) responses, down-regulation of MARB by RNA interference (RNAi) did not reduce the number of responding neurons or the size of evoked responses, suggesting that additional subunits remain to be identified in Manduca.
BoneMA – Synthesis and Characterization of a Methacrylated Bone-derived Hydrogel for Bioprinting of Vascularized Tissues

S. Prakash Parthiban,Avathamsa Athirasala,Anthony Tahayeri,Reyan Abdelmoniem,Anne George,Luiz E. Bertassoni

DOI: https://doi.org/10.1101/2020.03.02.974063

2020-03-04

Abstract:Abstract It has long been proposed that recapitulating the extracellular matrix (ECM) of native human tissues in the laboratory may enhance the regenerative capacity of engineered scaffolds in-vivo. Organ- and tissue-derived decellularized ECM biomaterials have been widely used for tissue repair, especially due to their intrinsic biochemical cues that can facilitate repair and regeneration. The main purpose of this study was to synthesize a new photocrosslinkable human bone-derived ECM hydrogel for bioprinting of vascularized scaffolds. To that end, we demineralized and decellularized human bone fragments to obtain a bone matrix, which was further processed and functionalized with methacrylate groups to form a photocrosslinkable methacrylate bone ECM hydrogel – BoneMA. The mechanical properties of BoneMA were tunable, with the elastic modulus increasing as a function of photocrosslinking time, while still retaining the nanoscale features of the polymer networks. The intrinsic cell-compatibility of the bone matrix ensured the synthesis of a highly cytocompatible hydrogel. The bioprinted BoneMA scaffolds supported vascularization of endothelial cells and within a day led to the formation of interconnected vascular networks. We propose that such a quick vascular network formation was due to the host of pro-angiogenic biomolecules present in the bone ECM matrix. Further, we also demonstrate the bioprintability of BoneMA in microdimensions as injectable ECM-based building blocks for microscale tissue engineering in a minimally invasive manner. We conclude that BoneMA may be a useful hydrogel system for tissue engineering and regenerative medicine.
BoneMA—synthesis and characterization of a methacrylated bone-derived hydrogel for bioprinting of in-vitro vascularized tissue constructs

S Prakash Parthiban,Avathamsa Athirasala,Anthony Tahayeri,Reyan Abdelmoniem,Anne George,Luiz E Bertassoni

DOI: https://doi.org/10.1088/1758-5090/abb11f

2021-04-09

Biofabrication

Abstract:Abstract It has long been proposed that recapitulating the extracellular matrix (ECM) of native human tissues in the laboratory may enhance the regenerative capacity of engineered scaffolds in-vivo . Organ- and tissue-derived decellularized ECM biomaterials have been widely used for tissue repair, especially due to their intrinsic biochemical cues that can facilitate repair and regeneration. The main purpose of this study was to synthesize a new photocrosslinkable human bone-derived ECM hydrogel for bioprinting of vascularized scaffolds. To that end, we demineralized and decellularized human bone fragments to obtain a bone matrix, which was further processed and functionalized with methacrylate groups to form a photocrosslinkable methacrylate bone ECM hydrogel— bone-derived biomaterial (BoneMA). The mechanical properties of BoneMA were tunable, with the elastic modulus increasing as a function of photocrosslinking time, while still retaining the nanoscale features of the polymer networks. The intrinsic cell-compatibility of the bone matrix ensured the synthesis of a highly cytocompatible hydrogel. The bioprinted BoneMA scaffolds supported vascularization of endothelial cells and within a day led to the formation of interconnected vascular networks. We propose that such a quick vascular network formation was due to the host of pro-angiogenic biomolecules present in the bone ECM matrix. Further, we also demonstrate the bioprintability of BoneMA in microdimensions as injectable ECM-based building blocks for microscale tissue engineering in a minimally invasive manner. We conclude that BoneMA may be a useful hydrogel system for tissue engineering and regenerative medicine.

engineering, biomedical,materials science, biomaterials
Enhanced bone regeneration with bioprinted GelMA/Bentonite scaffolds inspired by bone matrix

Jian Wang,Dongyang Zhou,Guangchao Wang,Miaomiao Wang,Fuxiao Wang,Yafei Han,Xiao Chen,Yan Hu,Fengjin Zhou,Zhongmin Shi,Xiaoxiang Ren,Jiacan Su

DOI: https://doi.org/10.1080/17452759.2024.2345765

IF: 10.6

2024-04-29

Virtual and Physical Prototyping

Abstract:In bone tissue engineering, the search for improved repair methods is crucial, given the drawbacks of traditional strategies like donor site issues and immune rejection. Addressing these challenges, this paper introduces an innovative GelMA/Bentonite composite bioink for 3D bioprinting, designed to create scaffolds that closely emulate native bone tissue. GelMA is selected for its biocompatibility and modifiable mechanics, while Bentonite's mineral richness and ion exchange capacity are harnessed to enhance scaffold structure and promote an osteogenic microenvironment. This research marks the inaugural incorporation of Bentonite into a bioink, a significant stride forward given its established safety in pharmaceuticals and versatility across industries. This bioink formulation signifies a breakthrough in bone tissue engineering, aiming to improve the osteointegration and regeneration of bone tissue. Combining Bentonite with GelMA marks a key step in creating bioinks that enhance bone healing, potentially transforming scaffold-based bone regeneration and pioneering the use of natural nanomaterials in medicine.

engineering, manufacturing,materials science, multidisciplinary
Meticulously engineered three-dimensional-printed scaffold with microarchitecture and controlled peptide release for enhanced bone regeneration

Jin Yang,Kanwal Fatima,Xiaojun Zhou,Chuanglong He

DOI: https://doi.org/10.12336/biomatertransl.2024.01.007

2024-03-28

Abstract:The repair of large load-bearing bone defects requires superior mechanical strength, a feat that a single hydrogel scaffold cannot achieve. The objective is to seamlessly integrate optimal microarchitecture, mechanical robustness, vascularisation, and osteoinductive biological responses to effectively address these critical load-bearing bone defects. To confront this challenge, three-dimensional (3D) printing technology was employed to prepare a polycaprolactone (PCL)-based integrated scaffold. Within the voids of 3D printed PCL scaffold, a methacrylate gelatin (GelMA)/methacrylated silk fibroin (SFMA) composite hydrogel incorporated with parathyroid hormone (PTH) peptide-loaded mesoporous silica nanoparticles (PTH@MSNs) was embedded, evolving into a porous PTH@MSNs/GelMA/SFMA/PCL (PM@GS/PCL) scaffold. The feasibility of fabricating this functional scaffold with a customised hierarchical structure was confirmed through meticulous chemical and physical characterisation. Compression testing unveiled an impressive strength of 17.81 ± 0.83 MPa for the composite scaffold. Additionally, in vitro angiogenesis potential of PM@GS/PCL scaffold was evaluated through Transwell and tube formation assays using human umbilical vein endothelium, revealing the superior cell migration and tube network formation. The alizarin red and alkaline phosphatase staining assays using bone marrow-derived mesenchymal stem cells clearly illustrated robust osteogenic differentiation properties within this scaffold. Furthermore, the bone repair potential of the scaffold was investigated on a rat femoral defect model using micro-computed tomography and histological examination, demonstrating enhanced osteogenic and angiogenic performance. This study presents a promising strategy for fabricating a microenvironment-matched composite scaffold for bone tissue engineering, providing a potential solution for effective bone defect repair.

Das Geschlechtsverhältnis der ehelichen und unehelichen Lebend- und Totgeburten im Kriege

Nanofibrous polyelectrolyte complex incorporated BSA-alginate composite bioink for 3D bioprinting of bone mimicking constructs

Composite bioink incorporating cell-laden liver decellularized extracellular matrix for bioprinting of scaffolds for bone tissue engineering

3D printing of PCL-ceramic composite scaffolds for bone tissue engineering applications

Printing bone in a gel: using nanocomposite bioink to print functionalised bone scaffolds

Desktop-Stereolithography 3D Printing of a Polyporous Extracellular Matrix Bioink for Bone Defect Regeneration

Multimaterial coextrusion (bio)printing of composite polymer biomaterial ink and hydrogel bioink for tissue fabrication

Development of cell-laden photopolymerized constructs with bioactive amorphous calcium magnesium phosphate for bone tissue regeneration via 3D bioprinting

3D Bioprinting of shear-thinning hybrid bioinks with excellent bioactivity derived from gellan/alginate and thixotropic magnesium phosphate-based gels

Construction of 3D bioprinting of HAP/collagen scaffold in gelation bath for bone tissue engineering

Some experimental results in adaptive prediction DPCM coding of images

Proceedings of the Twenty-Ninth Annual ACM-SIAM Symposium on Discrete Algorithms, SODA 2018, New Orleans, LA, USA, January 7-10, 2018

3D bioprinting of mechanically tuned bioinks derived from cardiac decellularized extracellular matrix

3D printing of hybrid biomaterials for bone tissue engineering: Calcium-polyphosphate microparticles encapsulated by polycaprolactone

Suitability of Gelatin Methacrylate and Hydroxyapatite Hydrogels for 3D-Bioprinted Bone Tissue

3D bioprinting by reinforced bioink based on photocurable interpenetrating networks for cartilage tissue engineering

Expression and function of two nicotinic subunits in insect neurons.

BoneMA – Synthesis and Characterization of a Methacrylated Bone-derived Hydrogel for Bioprinting of Vascularized Tissues

BoneMA—synthesis and characterization of a methacrylated bone-derived hydrogel for bioprinting of in-vitro vascularized tissue constructs

Enhanced bone regeneration with bioprinted GelMA/Bentonite scaffolds inspired by bone matrix

Meticulously engineered three-dimensional-printed scaffold with microarchitecture and controlled peptide release for enhanced bone regeneration