Abstract:We present a new, robust three dimensional microfabrication method for highly parallel microfluidics, to improve the throughput of on-chip material synthesis by allowing parallel and simultaneous operation of many replicate devices on a single chip. Recently, parallelized microfluidic chips fabricated in Silicon and glass have been developed to increase the throughput of microfluidic materials synthesis to an industrially relevant scale. These parallelized microfluidic chips require large arrays (>10,000) of Through Silicon Vias (TSVs) to deliver fluid from delivery channels to the parallelized devices. Ideally, these TSVs should have a small footprint to allow a high density of features to be packed into a single chip, have channels on both sides of the wafer, and at the same time minimize debris generation and wafer warping to enable permanent bonding of the device to glass. Because of these requirements and challenges, previous approaches cannot be easily applied to produce three dimensional microfluidic chips with a large array of TSVs. To address these issues, in this paper we report a fabrication strategy for the robust fabrication of three-dimensional Silicon microfluidic chips consisting of a dense array of TSVs, designed specifically for highly parallelized microfluidics. In particular, we have developed a two-layer TSV design that allows small diameter vias (d < 20 µm) without sacrificing the mechanical stability of the chip and a patterned SiO2 etch-stop layer to replace the use of carrier wafers in Deep Reactive Ion Etching (DRIE). Our microfabrication strategy allows >50,000 (d = 15 µm) TSVs to be fabricated on a single 4" wafer, using only conventional semiconductor fabrication equipment, with 100% yield (M = 16 chips) compared to 30% using previous approaches. We demonstrated the utility of these fabrication strategies by developing a chip that incorporates 20,160 flow focusing droplet generators onto a single 4" Silicon wafer, representing a 100% increase in the total number of droplet generators than previously reported. To demonstrate the utility of this chip for generating pharmaceutical microparticle formulations, we generated 5-9 µm polycaprolactone particles with a CV < 5% at a rate as high as 60 g/hr (>1 trillion particles/hour).

Laminar flow synthesis of submicron CaCO$_3$ particles in 3D printed microfluidic chips

Synthesis of Submicron CaCO3 Particles in 3D-Printed Microfluidic Chips Supporting Advection and Diffusion Mixing

Microfluidic Vaterite Synthesis: Approaching the Nanoscale Particles

Synthesis of scalable microdroplets with fluid instability of shearing flow in microfluidics

Continuous Multistage Synthesis and Functionalization of Sub-100 Nm Silica Nanoparticles in 3D-Printed Continuous Stirred-Tank Reactor Cascades.

Engineering 3D Printed Microfluidic Chips for the Fabrication of Nanomedicines

Microfluidic-Assisted Synthesis of Hybrid Carbonate Calcium Microparticles Modified by Silver Nanoparticles

Strategy for fast manufacturing of 3D hydrodynamic focusing multilayer microfluidic chips and its application for flow-based synthesis of gold nanoparticles

Microfluidic Synthesis and Analysis of Bioinspired Structures Based on CaCO3 for Potential Applications as Drug Delivery Carriers

A microfluidic platform for the controlled synthesis of architecturally complex liquid crystalline nanoparticles

Microfluidic Synthesis of Macroporous Copolymer Particles

Synthesis of perovskite nanoparticles in microfluidic chips

3D Nanofabrication inside rapid prototyped microfluidic channels showcased by wet-spinning of single micrometre fibres

3D Printed Integrated Multi-Layer Microfluidic Chips for Ultra-High Volumetric Throughput Nanoliposome Preparation

CFD Analysis and Life Cycle Assessment of Continuous Synthesis of Magnetite Nanoparticles Using 2D and 3D Micromixers

3D-Printed High-Density Droplet Array Chip for Miniaturized Protein Crystallization Screening under Vapor Diffusion Mode.

Three-Dimensional Large-Scale Fused Silica Microfluidic Chips Enabled by Hybrid Laser Microfabrication for Continuous-Flow UV Photochemical Synthesis

Calcium carbonate particle synthesis in a confined and dynamically thinning layer on a spin-coater – In situ deposition for cell adhesion

Controllable Synthesis of Multicompartmental Particles Using 3D Microfluidics.

Easy-to-perform and cost-effective fabrication of continuous-flow reactors and their application for nanomaterials synthesis

Robust Microfabrication of Highly Parallelized Three-Dimensional Microfluidics on Silicon