Abstract:This paper presents a comprehensive review of recent studies in electrical power generation from various thermal-consuming processes. In particular, the paper concentrates on TEG technology in recovering waste heat from industrial applications such as chimneys and automotive engines. Studies conclude that TEGs have a lower conversion efficiency (ranging between 5% and 10%), leading to low power output. Also, they state that most of the available TEGs have low operating temperatures limiting their commercial use. Therefore, an effort is taken to understand the key parameters that influence the performance of a thermoelectric generator. It is shown that a large temperature difference across the module, high heat dissipation from the cold side of the TEG and using thermoelectric materials with a high figure of merit generally improve the performance of the thermoelectric generator system. TEG module's cold-side temperature has a large effect on the power output than the hot-side temperature. Several geometric optimization methods, such as flaps and heat spreaders under natural convection resulted in a 129% and 42% increase in TEG power output, respectively. The survey also shows that forced cooling using side-mounted fans produces 58.6% more power compared to the top-mounted fan on the heat sink. However, optimization in fan selection is required to ensure that the power produced by forced cooling is sufficient to run the fans and output higher than the natural convection cooling case. Several studies also show that most of the commercially available TEG modules made from Bismuth telluride suffer from low operating temperature (maximum of 2600C) and have figure of merit of 1.2 maximum and low conversion efficiency (up to 5%). Recommendations are made to further research alternatives like SiGe alloys, clathrates, skutterudites, and complementary metal-oxide semiconductors with better temperature ranges and figures of merit.The carrier transport processes in thermoelectric materials are significantly correlated with the performance of thermoelectric devices (TEs), which is modeled in this study considering the drift-diffusion equation with thermoelectric contributions for detailing the effects of carrier transport on the yielded current density. A micro thermoelectric generator (μTEG) with boron and arsenic being respectively doped into Si0.7Ge0.3 for p-type and n-type thermoelectric materials is employed as the study case by the three-dimensional numerical simulation to reveal the effects of doping concentrations on the thermoelectric performance. Based on the simulation results a novel μTEG design that incorporates PN junctions to extract minority carriers to reduce the recombination rates of electrons and holes is proposed. The performances for conventional and the present novel μTEGs at different temperature differences are compared. The results show that there is an optimal doping concentration for the conventional μTEG to peak the output power and the thermoelectric conversion efficiency. In particular, the novel μTEG reveals a significant improvement of thermoelectric efficiency by approximately 20% as the hot-end temperature is above 900 K. The transport of minority carriers by the PN junctions demonstrates the expected effects through the analysis on the vector distribution of minority carrier current density.Thermal stress plays an important role in the lifetime of thermoelectric generators, and its minimization can prolong the usage of the generators. To figure out and efficiently lower the thermal stress, this study analyzes the thermoelectric performance and thermal stress of a thermoelectric module in a waste heat recovery system. The performance of the TEM with varied numbers of square pin fins in a flow channel is examined by computational fluid dynamics. The results indicate that for different numbers of square pin fins, the heat transfer rate of the module's hot side increases as the number of fins increases. When the number of fins increases from 36 to 84, the heat transfer rate improves by 8.57%. In addition, the temperature distribution in the module in a waste heat recovery system is uneven due to differences in heat transfer. Therefore, the thermal stress of the module is uneven, and the maximum thermal stress occurs in the TE legs, which are located at the corners of the module. To reduce the maximum thermal stress, the thicknesses of the ceramic plate and the thermoelectric legs are optimized using the multi-objective genetic algorithm. The optimization results indicate that the maximum thermal stress of the module is proportional to its output power, meaning that as the maximum thermal stress in the module is minimized, its output power will approach the minimum value. Instead, the same method is employed to minimize the maximum thermal stress on the module while maintaining its output -Abstract Truncated-

Application of exhaust heat dissipation in improving the performance of diesel generators via thermoelectric generator kit accompanied by Cu2O-water nanofluid

Experimental analysis of a photovoltaic/thermoelectric generator using cobalt oxide nanofluid and phase change material heat sink

A nanofluid-based hybrid photovoltaic-thermal -thermoelectric generator system for combined heat and power applications

Enhancement of system conversion energy from I.C. engine exhaust using heat exchanger and thermoelectric generators

A Novel Cooling System by Surface Corrugation and Nanofluid Utilization for the Performance Improvement of Photovoltaic Module Coupled with Thermoelectric Generator and Efficient Computations by Using Artificial Neural Network-Based Hybrid Scheme

Environmental and energy analysis for photovoltaic-thermoelectric solar unit in existence of nanofluid cooling reporting CO 2 emission reduction

Exergetic and Enviromental Assessment of a Photovoltaic Thermal-Thermoelectric System Using Nanofluids: Indoor Experimental Tests

Comprehensive review in waste heat recovery in different thermal energy-consuming processes using thermoelectric generators for electrical power generation

Photovoltaic thermal solar system in presence of nanofluid cooling analyzing environmental parameter in existence of TEG module

Thermoelectric Performance Evaluation and Optimization in a Concentric Annular Thermoelectric Generator under Different Cooling Methods

Comprehensive analysis of a novel cooling/electricity cogeneration system driven by waste heat of a marine diesel engine

Enhancing diesel engine cooling efficiency: A comprehensive numerical study on nanofluid coolants with exergy and economic analysis

Structure Optimization of Cylindrical Thermoelectric Generating System for Diesel Exhaust Waste Heat Recovery

Numerical examination of expanding the effectiveness of thermal photovoltaic framework by changing the level of heat transfer conveyance

Experimental study on thermoelectric characteristics of intermediate fluid thermoelectric generator

Study of the performance of thermoelectric generator for waste heat recovery from chimney: impact of nanofluid-microchannel cooling system

A modified exergy evaluation of using carbon-black/water/EG nanofluids as coolant of photovoltaic modules

Lateral comparison of the coupling parameters on the novel hexagonal shaped cross flow thermoelectric generator

Experimental study on low-temperature waste heat thermoelectric generator

Nanofluidic Two-Phase Closed Thermosyphon-Assisted Thermoelectric Generator for Heat Recovery from Coal Spontaneous Combustion

Enhancing Closed System Efficiency through CuO Nanofluids: Investigating Thermophysical Properties and Heat Transfer Performance