Abstract:BACKGROUND: The authors sought to demonstrate the safety and effectiveness of the multilevel stabilization screw (MLSS) technique in decreasing the incidence of proximal junctional failure in long segmental instrumented fusions for adult degenerative scoliosis.METHODS: Institutional review board approval was obtained and all patients with adult spinal deformity who underwent the MLSS technique were analyzed. A neuro-radiologist and spine-focused neurosurgeon not involved with the surgical treatment performed radiographic analysis. Proximal junctional angle was defined as the caudal endplate of the upper instrumented vertebra (UIV) to the cephalad endplate of two supradjacent vertebrae above the UIV. The UIV is defined as the most cephalad vertebra completed captured by the instrumentation. Abnormal proximal junctional kyphosis (PJK) was defined as proximal junctional sagittal Cobb angle >10 degrees and proximal junction sagittal Cobb angle at least 10 degrees greater than the preoperative measurement. The presence of both is criteria necessary to be considered abnormal.RESULTS: Twenty patients with degenerative scoliosis underwent the MLSS technique with the upper-instrumented vertebrae in the proximal thoracic spine. Fifteen patients met inclusion criteria with greater than 12 months radiographic and clinical follow up. Three patients were excluded due to lack of follow up imaging and two patients were excluded due to the inability to measure the UIV. Age range was 44-84 years with a mean of 66. Eleven of the 15 patients were over the age of 60 at the time of surgery. The male-to-female ratio was 4:11. Body mass index (BMI) range was 24-44 with a mean of 31.5 units. The follow up period ranged from 14 to 58 months with an average follow up of 30 months. The mean change in Cobb angle at the proximal junction was 4.00 degrees with a range from -0.92 to 9.13 degrees. There were no fractures or instrumentation failures at or near the proximal junction. There was no revision surgeries performed for proximal junctional failure. Retrospective clinical questionnaires revealed that surgical expectations were met in 15 of 19 patients surveyed, 79%. One patient was not reachable for a postoperative phone interview. In patients who were not satisfied with their overall experience, the change in Cobb angle ranged from -0.92 to 9.13 degrees with an average change of 3.90 degrees. Whereas patients reporting an overall positive experience had a change in Cobb angle range from -0.12 to 8.07 degrees with an average change of 4.05 degrees.CONCLUSION: PJK and failure are well-recognized suboptimal outcomes of long-segmental fusions of the thoracolumbar spine that can lead to significant neurological morbidity and costly revision surgeries. With no known proximal junction failures to date, the MLSS technique has shown promising results in preventing adverse proximal junctional conditions and can be safely performed under fluoroscopy guidance. Future direction includes a comparative study establishing the relative risk of developing PJK with this novel technique versus a traditional long-segmental thoracolumbar fusion.

Cyclic peptides from higher plants. 34. Segetalins G and H, structures and estrogen-like activity of cyclic pentapeptides from Vaccaria segetalis.

Clinically relevant biomechanical properties of three different fixation techniques of the upper instrumented vertebra in deformity surgery

Posterior spinal stabilization: A biomechanical comparison of Laminar Hook Fusion to a Pedicle Screw System

Instrumentation Techniques to Prevent Proximal Junctional Kyphosis and Proximal Junctional Failure in Adult Spinal Deformity Correction: A Systematic Review of Clinical Studies

Biomechanical Evaluation of an Adaptive-Motion Pedicle Screw Fixation System: Experimental and Numerical Analysis

Proximal junctional failure after surgical instrumentation in adult spinal deformity: biomechanical assessment of proximal instrumentation stiffness

A functional and structural analysis of the Sex combs reduced locus of Drosophila melanogaster.

Biomechanical Evaluation of Anterior Lumbar Interbody Fusion with Various Fixation Options: Finite Element Analysis of Static and Vibration Conditions.

Finite element analysis comparing a PEEK posterior fixation device versus pedicle screws for lumbar fusion

Finite Element Analysis of 3 Posterior Fixation Techniques in the Lumbar Spine

Topping-Off a Long Thoracic Stabilization With Semi-Rigid Constructs May Have Favorable Biomechanical Effects to Prevent Proximal Junctional Kyphosis: A Biomechanical Comparison

[Clinical and therapeutic consideration on so-called cysts and psudocysts of the lung].

Biomechanical comparison of posterior intermediate screw fixation techniques with hybrid monoaxial and polyaxial pedicle screws in the treatment of thoracolumbar burst fracture: a finite element study

Biomechanical properties analysis of posterior lumbar interbody fusion with transpedicular oblique screw fixation

Biomechanical assessment of the stabilization capacity of monolithic spinal rods with different flexural stiffness and anchoring arrangement

The potential of proximal junctional kyphosis prevention using a novel tether pedicle screw construct: an in silico study comparing the influence of standard and dynamic techniques on adjacent-level range of motion and load pattern

Biomechanical Analysis of Transpedicular Screw Fixation in the Subaxial Cervical Spine

Preventing proximal junctional failure in long segmental instrumented cases of adult degenerative scoliosis using a multilevel stabilization screw technique

Stress Distribution in Vertebral Bone and Pedicle Screw and Screw-Bone Load Transfers among Various Fixation Methods for Lumbar Spine Surgical Alignment: A Finite Element Study

Quantitative Biomechanical Evaluation for Optimal Spinal Instrumentation to Prevent Mechanical Complications in Spinal Fusion from the Lower Thoracic Spine to the Pelvis for Adult Spinal Deformity: A Finite Element Analysis