Abstract:All-solid-state batteries (ASSBs) provide the opportunity for substantially enhanced gravimetric and volumetric energy and power density and improved safety. However, these gains will not be realized without first overcoming substantial challenges, notably, the high interfacial resistance between electrodes and the solid-state electrolyte (SSE) which requires high stack pressures, on the order of 10,000 psi, to achieve high performance metrics.[1,2]. Already there is a large and growing body of research demonstrating the advantages of laser structuring of Li-ion battery materials for enhanced kinetics and shorter diffusion pathways [3,4]. This work extends these advantages to ASSBs through lowering the catholyte-SSE interfacial impedance by increasing its surface area and providing less torturous paths for ion diffusion. The work presented here uses a near-IR (1030 nm) femtosecond laser (pulse duration approx. 250 fs) to ablate microstructures into the surface of a slurry-cast LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811):Li 6 PS 5 Cl catholyte. Micrometer-sized channel structures were ablated at various depths and pitch spacings to assess the effect of patterning on cell performance. X-ray diffraction (XRD) and energy dispersive spectroscopy (EDS) measurements were acquired on both pristine and patterned samples to ensure that the femtosecond laser pulses do not cause any residual compositional or phase changes, respectively. Critically, low interfacial resistance will require that an SSE layer be applied to the patterned catholyte such that the microstructure is preserved while maintaining intimate contact between the catholyte and SSE layer. SSE layers were both slurry cast and pellet-pressed onto both pristine and patterned electrodes. Cross-sectional SEM was used to investigate the degree of interfacial contact, and relate interface quality to parameters such as SSE application technique (e.g., pellet pressing vs. slurry casting) and slurry properties (i.e., viscosity). The improvement to interfacial ionic conductivity is assessed using electrochemical impedance spectroscopy (EIS). The effect of stack pressure is analyzed in order to assess the degree to which laser patterning can alleviate stack pressure requirements in ASSBs. References: [1] Chen, Xinzhi, et al. "Enhancing interfacial contact in all solid state batteries with a cathode-supported solid electrolyte membrane framework." Energy & Environmental Science 3 (2019): 938-944. [2] Pervez, Syed Atif, et al. "Interface in solid-state lithium battery: challenges, progress, and outlook." ACS applied materials & interfaces 25 (2019): 22029-22050. [3] Pfleging, Wilhelm. "A review of laser electrode processing for development and manufacturing of lithium-ion batteries." Nanophotonics 3 (2018): 549-573. [4] Dunlap, Nathan, et al. "Laser ablation of Li-ion electrodes for fast charging: Material properties, rate capability, Li plating, and wetting." Journal of Power Sources 537 (2022): 231464. Figure 1

Air Stabilization of Li7P3S11 Solid-State Electrolytes through Laser-Based Processing

Femtosecond-Laser Microstructuring Improves Solid-State Electrolyte/Cathode Ionic Transport

Preparation of Metal-Oxide-Doped Li7P2S8Br0.25I0.75 Solid Electrolytes for All-Solid-State Lithium Batteries

Air-stable, high-conduction solid electrolytes of arsenic-substituted Li4SnS4

Recent Advances in Li1+xAlxTi2−x(PO4)3 Solid-State Electrolyte for Safe Lithium Batteries

Insight on air-induced degradation mechanism of Li7P3S11 to design a chemical-stable solid electrolyte with high Li2S utilization in all-solid-state Li/S batteries

Enhanced Air and Electrochemical Stability of Li7P3S11–Based Solid Electrolytes Enabled by Aliovalent Substitution of SnO2

Li10Ge(P1–xSbx)2S12 Lithium-Ion Conductors with Enhanced Atmospheric Stability

Enhanced Air and Electrochemical Stability of Li 7 P 3 S 11 –Based Solid Electrolytes Enabled by Aliovalent Substitution of SnO 2

Highly Conductive Sulfide Solid-State Electrolytes for All-Solid-State Li Battery

Stabilization of all-solid-state Li–S batteries with a polymer–ceramic sandwich electrolyte by atomic layer deposition

Solid-State Electrolyte for Lithium-Air Batteries: A Review

Air Stability and Interfacial Compatibility of Sulfide Solid Electrolytes for Solid‐State Lithium Batteries: Advances and Perspectives

Surface molecular engineering to enable processing of sulfide solid electrolytes in humid ambient air

Enhancing Moisture Stability of Sulfide Solid-State Electrolytes by Reversible Amphipathic Molecular Coating

A Versatile Li 6.5 In 0.25 P 0.75 S 5 I Sulfide Electrolyte Triggered by Ultimate‐Energy Mechanical Alloying for All‐Solid‐State Lithium Metal Batteries

A Versatile Li<sub>6.5</sub>In<sub>0.25</sub>P<sub>0.75</sub>S<sub>5</sub>I Sulfide Electrolyte Triggered by Ultimate-Energy Mechanical Alloying for All-Solid-State Lithium Metal Batteries

Recent developments in garnet based solid state electrolytes for thin film batteries

ll-solid-state Li – S batteries with a polymer – ceramic sandwich electrolyte by atomic layer deposition †

Ultrastable Anode Interface Achieved by Fluorinating Electrolytes for All-Solid-State Li Metal Batteries

Ultrafast Laser‐Induced Cathode/Electrolyte Interphase for High‐Voltage Poly(Ethylene Oxide)‐Based Solid Batteries