Abstract:Abstract Purpose Stem cell-based attempts at regenerating chronically failing heart have not met the clinical outcomes expected by experimental studies. The efficacy of cell transplant is largely dependent on the engraftment rate, which requires cells to receive an adequate blood supply. To address this issue, we propose to develop a composite tissue engineering construct made of biocompatible pre-vascularized fibrin hydrogel. The objectives of this study are to determine co-culture conditions and to optimize fabrication of fibrin hydrogels supporting generation of capillaries and cardiomyocyte activity at the same time. Materials and methods Rat primary cardiomyocytes were co-seeded with human umbilical vein endothelial cells (HUVECs) in fibrin hydrogels. Cultures were performed in 96 well plates. Cells were cultured in a mixture of medium conditioned with human dermal fibroblasts and of cardiomyocyte medium (1:1) for 8 days. To improve co-culture of the two cell types, insulin (1 μg/mL) and/or VEGF (5 ng/mL) were added 24 hours after the initial day of culture and maintained for 24 hours. The cells treated with VEGF were also treated 5 days after initial seeding with insulin and VEGF (insulin at 1 μg/mL and VEGF at 1 or 5 ng/mL). After culture, cardiomyocytes were immuno-stained for Troponin T or Connexin-43, endothelial cells for CD31, basement membrane for collagen IV. From spinning disk images, cardiomyocyte volume, contraction and total length/ branches of capillaries were measured. Results : We first determine the best conditions allowing the generation of active cardiomyocytes and the formation of a network of mature capillaries into fibrin hydrogels. We showed that cardiomyocytes volume and contraction were not influenced by the addition of VEGF or insulin. For cells treated with VEGF for 24 hours, total length and total branches of capillaries were significantly increased over other conditions without supplements (control), or with insulin alone or with VEGF. We also observed lumen formation and basement membrane deposition. Conclusions These results may provide a new model of vascularized human heart tissue for in vitro studies, displaying cardiomyocyte contractility together with lumenized capillary formation. Furthermore, our data may help overcome current obstacles toward the success of cardiac cell therapy for damaged myocardium. In such approach, endothelial capillaries will serve as structural and trophic support through inosculation with the host cardiac vasculature after epicardial graft. As a perspective of this work, and in order to improve the cardiomyocyte alignment and the development of capillaries, we will design specific PDMS mold to allow the formation of a micro-tissue. Application of human cardiac cells and implantation in in vivo model is expected. Acknowledgement/Funding ESC research grant, Fondation de l'avenir, Societe Francaise de Cardiologie, Institut Servier

Fibre-infused gel scaffolds guide cardiomyocyte alignment in 3D-printed ventricles

Precise Printing of Microfiber Scaffold with Gelatin Methacryloyl (gelma)/polyethylene Oxide (PEO) Bioink

GelMA Micropattern Enhances Cardiomyocyte Organization, Maturation, and Contraction Via Contact Guidance.

4D Printed Cardiac Construct with Aligned Myofibers and Adjustable Curvature for Myocardial Regeneration

3D bioprinting of mechanically tuned bioinks derived from cardiac decellularized extracellular matrix

Structure-induced Cell Growth by 3D Printing of Heterogeneous Scaffolds with Ultrafine Fibers

A 3D hydrogel scaffold with adjustable interlayer spacing for the formation of compact myocardial tissue

Mechanically Biomimetic Gelatin–Gellan Gum Hydrogels for 3D Culture of Beating Human Cardiomyocytes

Tunable Human Myocardium Derived Decellularized Extracellular Matrix for 3D Bioprinting and Cardiac Tissue Engineering

P4499Development of a hydrogel-based pre-vascularized 3D cardiac patch displaying capillary network

Bioprinting 3D Microfibrous Scaffolds for Engineering Endothelialized Myocardium and Heart-on-a-chip.

3D printing of self‐standing and vascular supportive multimaterial hydrogel structures for organ engineering

Fabrication and Characterization of Bio-Engineered Cardiac Pseudo Tissues

A multi-cellular 3D bioprinting approach for vascularized heart tissue engineering based on HUVECs and iPSC-derived cardiomyocytes

Rapid 3D Bioprinting of in Vitro Cardiac Tissue Models Using Human Embryonic Stem Cell-Derived Cardiomyocytes.

3D bioprinting microgels to construct implantable vascular tissue

Embedded 3D printing of dilute particle suspensions into dense complex tissue fibers using shear thinning xanthan baths

Fabrication of chitin-fibrin hydrogels to construct the 3D artificial extracellular matrix scaffold for vascular regeneration and cardiac tissue engineering

Anisotropic hydrogel scaffold by flow-induced stereolithography 3D printing technique

Direct 3D Printed Biomimetic Scaffolds Based on Hydrogel Microparticles for Cell Spheroid Growth

Accordion-like honeycombs for tissue engineering of cardiac anisotropy