[Comparison between productive and latent infection by measles virus in subacute panencephalitis].

M. Dubois‐Dalcq

Abstract:

What problem does this paper attempt to address?

Performance assessment of BeiDou B3-based real-time orbit determination for LEO satellites

Xin YU,Xiao-jun JIN,Shi-ming MO,Wei ZHANG,Zhao-bin XU,Zhong-he JIN

DOI: https://doi.org/10.3785/j.issn.1008-973X.2020.03.020

2020-01-01

Abstract:Real-time orbit determination simulations were conducted using the space-borne GPS/BDS (BeiDou navigation satellite system) receiver developed for the ZDPS-3 mission. The orbit determination performance based on BDS, especially the B3 frequency, was evaluated. As results, with the higher chip rate, the anti-noise performance of pseudo-noise code of B3 was obviously better than that of B1, which can be utilized to achieve a better orbit determination accuracy. Based on the establishment of the observation model and the orbit determination algorithm model, a hardware-in-loop simulation experimental platform was established after the quality of the receiver’s field observation data was evaluated. The simulation results show that, under the same conditions, the real-time orbit determination accuracy of the B3 frequency is better than that of B1, and comparable to that of GPS in full operation.
Performance Evaluation of Precise Point Positioning for BeiDou-3 B1c/B2a Signals in the Global Range

Ershen Wang,Tao Yang,Zhi Wang,Yize Zhang,Jing Guo,Wansen Shu,Pingping Qu

DOI: https://doi.org/10.3390/s21175780

IF: 3.9

2021-08-27

Sensors

Abstract:With the construction and development of the BeiDou navigation satellite system (BDS), the precise point positioning (PPP) performance of the BDS is worthy of research. In this study, observational data from 17 stations around the world across 20 days are used to comprehensively evaluate the PPP performance of BDS B1c/B2a signals. For greater understanding, the results are also compared with the Global Positioning System (GPS) and BDS PPP performance of different signals and system combinations. The evaluation found root mean square (RMS) values of the static PPP in the north (N), east (E), and upward (U) components, based on the B1c/B2a frequency of BDS-3, to be 6.9 mm, 4.7 mm, and 26.6 mm, respectively. Similar to the static positioning, the RMS values of kinematic PPP in the three directions of N, E, and U are 2.6 cm, 6.0 cm, and 8.5 cm, respectively. Besides this, the static PPP of BDS-3 (B1cB2a) and BDS-2 + BDS-3 (B1IB3I) have obvious system bias. Compared with static PPP, kinematic PPP is more sensitive to the number of satellites, and the coordinate accuracy in three dimensions can be increased by 27% with the combination of GPS (L1L2) and BDS. Compared with BDS-2+BDS-3 (B1IB3I), the convergence time of BDS-3 (B1CB2a) performs better in both static and kinematic modes. The antenna model does not show a significant difference in terms of the effect of the convergence speed, though the number of satellites observed has a certain influence on the convergence time.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Global precision analysis of carrier phase relative positioning in BeiDou navigation satellite system and United States global positioning system

Letao Zhou,Dingfa Huang,Wei Feng,Wu Chen,Xi Zhang,Li Yan

DOI: https://doi.org/10.1007/s11430-017-9287-3

2019-02-26

Science China Earth Sciences

Abstract:In this paper, we derived a high-efficiency formula for calculating the precision of carrier phase relative positioning, analyzed the various factors that affect the positioning accuracy using the carrier phase, and proposed the concept of using a frequency dilution of precision to describe the quantitative effect of different frequency combinations on the positioning precision. To this end, we computed and plotted the global spatial distribution map of the relative positioning dilution of precision for single-day solution, half-hour solution, and single-epoch solution of the global positioning system (GPS), regional Beidou navigation satellite system (BDS2), future global Beidou navigation satellite system (BDS3), and their fusion systems. Using processing software with autonomous intellectual property rights (GCN and VENUS/ARSNet), we solved the measurement data and examined the positioning precision of the single-day solution and single-epoch solution of GPS and BDS2. The analysis demonstrated that the B1/B2 frequency positioning precision of BDS2 was better than that of L1/L2 frequency positioning of GPS, but the positioning precision of the BDS2 is worse than that of GPS over most of the service region of the BDS2. Further, the positioning precision of BDS3 is better than that of GPS in the Asia-Pacific region, while it is the opposite in other regions. Based on these conclusions, we put forth some optimization recommendations regarding the signal frequency of the navigation system and GPS measurement standards to serve as references for optimizing the system performance and formulating standards.

geosciences, multidisciplinary
Investigating Performance of BDS-2+3 Dual-Frequency Absolute Positioning With Broadcast Ephemerides, RTS and Final MGEX Products

Shengnan Liu,Shaolin Zhu,Jian Zhang

DOI: https://doi.org/10.1109/access.2023.3247438

IF: 3.9

2023-01-01

IEEE Access

Abstract:BDS-3 was formally put into service on July 31, 2020, and now along with BDS-2 provides the positioning, navigation and timing services. In this contribution, different techniques of dual-frequency absolute positioning using the fully serviceable BDS-2+3 constellation are evaluated and compared to the positioning performance of GPS constellation. The accuracy of BDS-3 broadcast ephemerides is significantly higher than that of BDS-2 and is comparable to that of GPS, while BDS-3 International GNSS Service (IGS) Real-Time Service (RTS) products are not as good as GPS at this stage. The static Single Point Positioning (SPP) using BDS-2+3 pseudoranges based on broadcast ephemerides attains the positioning accuracy of 0.743/0.601/1.021 m (95%) and 0.453/0.365/0.566 m (68%) in east/north/up components, while its positioning accuracy is 1.210/1.097/2.447 m (95%) and 0.660/0.586/1.264 m (68%) in kinematic mode. BDS-2+3 Precise Point Positioning (PPP) using pseudoranges with carrier-phase observations based on broadcast ephemerides is able to achieve a positioning accuracy of 0.239/0.174/0.529 m (95%) and 0.115/0.096/0.296 m (68%) in static mode, and 0.636/0.486/1.108 m (95%) and 0.304/0.242/0.556 m (68%) in kinematic mode. BDS-2+3 PPP based on final Multi-GNSS Experiment (MGEX) product can obtain the positioning accuracy of centimeter to millimeter in static mode and the centimeter-level positioning accuracy in kinematic mode. The experiment results show that the positioning performances of BDS-2+3 using broadcast ephemerides and final MGEX products are both comparable to those of GPS. However, due to the poor quality and incomeless of BDS IGS RTS product, BDS-2+3 SPP and PPP based on IGS RTS product obtain the poor positioning accuracies in both static and kinematic modes, which are obviously worse than the counterparts of GPS. Another remarkable result can be obtained that BDS-2+3 achieves a better positioning performance in Asia-Pacific region at higher cut-off elevations as compared to GPS positioning.

computer science, information systems,telecommunications,engineering, electrical & electronic
Satellite availability and positioning performance of uncombined precise point positioning using BeiDou-2 and BeiDou-3 multi-frequency signals

Xinyun Cao,Fei Shen,Shoujian Zhang,Jiancheng Li

DOI: https://doi.org/10.1016/j.asr.2020.11.011

IF: 2.611

2021-02-01

Advances in Space Research

Abstract:To realize the smooth transition from regional BeiDou Navigation Satellite System (BDS-2) to the global one (BDS-3), the integration of BDS-2 and BDS-3 is important for providing continuous, stable and reliable positioning, navigation and timing (PNT) services for global users. This work used 154 globally distributed multi-GNSS (Global Navigation Satellite System) experiment stations spanning 30 days to analyze the satellite availability and positioning performance of uncombined precise point positioning (UC-PPP) under current BDS-2 and BDS-3 constellations. We focused on three issues: the influence of BDS-3 receiver tracking abilities, the positioning performance among different areas, and the benefit of multi-frequency observations. The results show that the elliptical zone caused by poor BDS-2 satellite visibility is disappeared when the evenly distributed BDS-3 medium earth orbit satellites are introduced. When BDS-3 are integrated with BDS-2, the area with the Position Dilution of Precision (PDOP) less than 2 can be expanded to 75° S-75° N and 30° E-150° W. The positioning performance of BDS-3 and BDS-2/BDS-3 UC-PPP are seriously affected by the receiver tracking abilities of BDS-3 signals. When the maximum pseudo-random noise sequences (PRNs) of BDS-3 satellites tracked by stations are within 30 or 37, the positioning accuracy of static UC-PPP can be improved by 22.94% or 8.27 % due to the integration of BDS-2 and BDS-3. Besides, the most improvement of BDS-2 and BDS-3 integration is achieved in Asia-Pacific regions, especially for the kinematic UC-PPP or the poor receiver tracking abilities of BDS-3. Similar to the multi-frequency BDS-2 UC-PPP, the benefit of multi-frequency signals for BDS-3 or BDS-2/BDS-3 UC-PPP is also non-vital. The three-dimensional positioning accuracy of BDS-2/BDS-3 multi-frequency UC-PPP in static mode and kinematic mode are 2.24 cm and 5.39 cm, while the corresponding convergence time are 49.62 min and 73.80 min, respectively. Compared with BDS-2, both the positioning accuracy and the convergence time of BDS-2/BDS-3 joint UC-PPP are improved by approximately over 50%, which indicates that BDS-3 has a great potential to provide high-quality PNT services as other global navigation satellite systems.

geosciences, multidisciplinary,meteorology & atmospheric sciences,astronomy & astrophysics,engineering, aerospace
Signal-in-space range error and positioning accuracy of BDS-3

Weiping Liu,Bo Jiao,Jinming Hao,Zhiwei Lv,Jiantao Xie,Jing Liu

DOI: https://doi.org/10.1038/s41598-022-12012-y

2022-05-17

Abstract:Being the first mixed-constellation global navigation system, the global BeiDou navigation system (BDS-3) designs new signals, the service performance of which has attracted extensive attention. In the present study, the Signal-in-space range error (SISRE) computation method for different types of navigation satellites was presented. The differential code bias (DCB) correction method for BDS-3 new signals was deduced. Based on these, analysis and evaluation were done by adopting the actual measured data after the official launching of BDS-3. The results showed that BDS-3 performed better than the regional navigation satellite system (BDS-2) in terms of SISRE. Specifically, the SISRE of the BDS-3 medium earth orbit (MEO) satellites reached 0.52 m, slightly inferior compared to 0.4 m from Galileo, marginally better than 0.59 m from GPS, and significantly better than 2.33 m from GLONASS. The BDS-3 inclined geostationary orbit (IGSO) satellites achieved the SISRE of 0.90 m, on par with that (0.92 m) of the QZSS IGSO satellites. However, the average SISRE of BDS-3 geostationary earth orbit (GEO) satellites was 1.15 m, which was marginally inferior to that of the QZSS GEO satellite (0.91 m). In terms of positioning accuracy, the new signals B1C and B2a are considered together with the transition signals B1I and B3I. The overall three-dimensional single-frequency standard point positioning (SPP) accuracy of BDS-3 B1C, B2a, B1I, and B3I gained an accuracy level better than 5 m. Moreover, the B1I signal exhibited the best positioning accuracy in the Asian-Pacific region, while the B1C signal set forth the best positioning accuracy in the other regions. Owing to the advantage in signal frequency, the dual-frequency SPP accuracy of B1C + B2a surpassed that of the transitional signal of B1I + B3I. Since there are more visible satellites in Asia-Pacific, the positioning accuracy of BDS-3 was moderately superior to that of GPS. The precise point positioning (PPP) accuracy of BDS-3 B1C + B2a or B1I + B3I converged to the order of centimeters, marginally inferior to that of the GPS L1 + L2. However, these three combinations had a similar convergence time of approximately 30 min.
Accuracy Analysis of BeiDou-3/GPS Real-Time Precise Common View Time Transfer Based on Carrier-Phase

Hongyuan Zhou,Binyong Sun,Li-Peng Sun,Lihua Zhao,Zhe Zhang,Ge Wang,Kan Wang,Xuhai Yang

DOI: https://doi.org/10.1007/978-981-99-6944-9_38

2023-01-01

Abstract:The accuracy of GNSS timing through standard service could not meet the requirements of new-generation mobile communication, distributed cooperative observation, deep space exploration, and many other fields. The performance of BeiDou-3 Navigation Satellite System (BDS-3)/GPS Precise Common View (PCV) time transfer based on carrier-phase is investigated to address this issue. Using 33-day consecutive observations of 11 stations from the tracking network of the international GNSS Monitoring and Assessment System and the International GNSS Service, long baseline PCV time transfer experiments were carried out from several aspects, including different signals, different orbit products, and real-time and post-processing. The accuracy of PCV time transfer results is evaluated by comparing them with the results produced by PPP time transfer. For the real-time PCV time transfer based on broadcast ephemeris, the accuracy of results with BDS-3 is within 0.2 ns for baselines up to 3000 km, which is better than that with GPS. In the aspect of real-time and post-processing PCV time transfer based on precise ephemeris, while it is hard to get a regular solution with GPS-only observations for baselines over 7000 km, it is still better than 0.6 ns with BDS-only observations. For baselines of 3000 km and less, GPS and BDS-3 PCV results with precise ephemeris are of comparable accuracy. Based on precise ephemeris, the accuracy of real-time PCV time transfer is close to post-processing PCV. From the experiment results, one can find that PCV time transfer is unaffected by the differential code bias at the satellite end and is immune to the day-boundary discontinuities caused by the clock products. The results show that the carrier-phase-based BeiDou-3 PCV time transfer can achieve sub-nanosecond accuracy in post-processing and real-time mode for baselines as long as 7000 km.
Modeling and performance assessment of BDS-2/BDS-3 triple-frequency ionosphere-free and uncombined precise point positioning

Shaolin Zhu,Dongjie Yue,Lina He,Jian Chen,Zhiqiang Liu

DOI: https://doi.org/10.1016/j.measurement.2021.109564

IF: 5.6

2021-08-01

Measurement

Abstract:<p>The global BeiDou Navigation Satellite System (BDS-3) and regional system (BDS-2) are transmitting signals on three or more frequencies, which brings more choices and practical potentials. To deeply integrate and fully utilize the BDS-2 and BDS-3 signals, this research is dedicated to the modeling and assessment of BDS-2/BDS-3 combined triple-frequency precise point positioning (PPP). Using ionosphere-free (IF) or uncombined (UC) observables, the three BDS-2/BDS-3 combined triple-frequency PPP models, named IF1213, IF123 and UC123 are developed. Particularly, new biases such as time delay bias (TDB) and inter-frequency bias (IFB) as well as the parameterizations are addressed. One-month observations from 16 Multi-GNSS Experiment (MGEX) stations located in and around the Asia-Pacific region are utilized to validate and compare the models. The results indicate that the three BDS-2/BDS-3 combined triple-frequency PPP models have the comparable performance and the third frequency makes a marginal contribution to positioning and tropospheric delay retrieval. The TDB should be carefully considered in BDS-2/BDS-3 combined PPP, especially for the IF123 model due to the larger absolute values of TDB. Meanwhile, the IFB derived from receiver uncalibrated code delay difference shows good stability in both short-term (intra-day) and long-term (inter-day) periods. In addition, demonstrated by triple-frequency PPP tests with one-month data from 47 global MGEX stations, the BDS-2/BDS-3 combined constellation allows for significantly improved convergence performance and positioning accuracy over the BDS-2-only constellation. The BDS-3 system has the ability to provide the precise positioning accuracy of 12.1/9.8/15.8 mm on a global scale after the convergence time of 23.0/13.2/24.7 min in east/north/up components.</p>

engineering, multidisciplinary,instruments & instrumentation
Long-term performance analysis of BDS-3 precise point positioning (PPP-B2b) service

Sun, Shuang,Wang, Min,Liu, Changjian,Meng, Xin,Ji, Rui

DOI: https://doi.org/10.1007/s10291-023-01409-5

2023-02-17

GPS Solutions

Abstract:Since 2020, the BeiDou Navigation Satellite System (BDS) has launched new precise point positioning service which provides precise correction of GPS and BDS-3 satellites to help users realize real-time precise point positioning, known as PPP-B2b service. After being fully operational for more than one year, this contribution comprehensively analyzes the performance of PPP-B2b in terms of correction availability, clock and orbit quality and positioning accuracy with PPP-B2b messages of nearly 48 weeks from 2021 to 2022. The results show that in the PPP-B2b service, the orbit radial differences of BDS-3 MEO, GPS, and BDS-3 IGSO satellites are 0.056 m, 0.069 m, and 0.172 m, respectively, compared to the GFZ final orbit, while the difference of along-track and cross-track is more than three times the radial. For BDS-3 MEO satellites from different manufacturers, the RMS of Satellite Laser Ranging (SLR) residuals is different, with a maximum of 0.11 m. Restricted by the regional tracking network, the correction series of PPP-B2b service are discontinuous, and there are constant satellite-specific clock biases in different arcs of the satellite. Thus, the STD and RMS of satellite clock offset and signal-in-space ranging error (SISRE) are calculated using the method of weighting by arcs. The STD of SISRE for BDS-3 MEO, GPS and BDS-3 IGSO are 0.059 m, 0.092 m and 0.174 m, respectively. A total of 108 days of observation data from 12 MGEX stations of the East Asia region are selected to analyze the positioning performance of PPP-B2b. The results of day-by-day static PPP are stable at the centimeter level, while the average convergence time of GPS-only (61.65 min) is longer than BDS-3-only (45.12 min), which the constant bias in clock offset may cause. To analyze the effect of this bias, the bias is calculated and used as a correction to the PPP-B2b clocks. The convergence time of BDS-3 and GPS positioning is reduced by 48.7% and 65.9%, respectively, after correcting this bias, which confirms the influence of clock constant bias on positioning convergence.

remote sensing
Modeling and performance assessment of precise point positioning with multi-frequency GNSS signals

Zhiyuan Wu,Qianxin Wang,Zhihao Yu,Chao Hu,Honghui Liu,Shan Han

DOI: https://doi.org/10.1016/j.measurement.2022.111687

IF: 5.6

2022-09-30

Measurement

Abstract:The development of global navigation satellite system (GNSS), especially BeiDou-3 Navigation Satellite System (BDS-3) and Galileo system, promotes the progress of the precise point positioning (PPP) technology. Considering deep integration and full utilization of GNSS signals, this study dedicates to developing three triple-frequency PPP models apply to multi-constellation including BDS-3. Besides, some biases such as differential code bias (DCB), inter-frequency bias (IFB) and inter-system bias (ISB) are also addressed. Through the ten-day datasets collected from 160 stations, the multi-frequency PPP models for single- and multi-constellation solutions are analyzed and compared from static positioning performance, Zenith Tropospheric Delay (ZTD) estimates, ISB estimates, and IFB estimates. The results indicate that the triple-frequency PPP models, especially two dual-frequency ionosphere-free (IF) model namely TIF with triple-constellation which can provide the positioning accuracy of 4.89, 7.31, 12.1 mm after the convergence time of 10.75 min in east, north and up directions, perform better than the dual-frequency model, apart from the a single IF model with GPS. Interestingly, the positioning performance is not effectively improved with the addition of GLONASS constellation. But the performance of GAL/BDS combined constellation is comparable to GPS single constellation in TIF model.

engineering, multidisciplinary,instruments & instrumentation
Dual-frequency to five-frequency real-time precise point positioning using new BDS-3 PPP-B2b service

Haochen Yang,Xiaodong Ren,Mingxiu Liu,Xiaohong Zhang

DOI: https://doi.org/10.1186/s40623-024-02031-6

2024-06-13

Earth Planets and Space

Abstract:BeiDou global navigation satellite system (BDS-3), a developed GNSS by China, has the ability to support five different signals, including B1I, B3I, B1C, B2a, and B2b. Meanwhile, BDS-3 has officially provided the satellite-based precise point positioning (PPP) service through the B2b signal (PPP-B2b) since 2021. It's necessary to conduct a comprehensive analysis on multi-frequency PPP with PPP-B2b corrections. In this study, a multi-frequency undifferenced and uncombined PPP model (UDUC) using PPP-B2b corrections was employed to investigate dual-frequency to five-frequency real-time PPP performance. The results show that compared with the conventional dual-frequency solutions, multi-frequency solutions can improve both the convergence performances and positioning accuracy of PPP-B2b service, especially during the convergence stage. The quad-frequency and five-frequency solutions can achieve the best positioning performance. The static solutions of multi-frequency PPP models reach the centimeter-level accuracy after convergence. In kinematic mode, the convergence time of the five-frequency PPP results is reduced by 23.5% compared with the dual-frequency results. The root mean square (RMS) errors of the five-frequency PPP in the E, N, and U components are 7.1 cm, 4.8 cm, and 12.4 cm, which are improved by 6.8%, 11.5%, and 5.5%, respectively.

geosciences, multidisciplinary
Advancing Precise Orbit Determination and Precise Point Positioning of BDS-3 Satellites from B1IB3I to B1CB2a: Comparison and Analysis

Chen Wang,Tengjie Luo,Shitong Chen,Pan Li

DOI: https://doi.org/10.3390/rs15204926

IF: 5

2023-10-13

Remote Sensing

Abstract:The third generation of the Chinese BeiDou Navigation Satellite System (BDS-3) broadcasts new signals, i.e., B1C, B2a, and B2b, along with the legacy signals of BDS-2 B1I and B3I. The novel signals are demonstrated to show adequate upgraded performance, due to the restrictions on the ground tracking network for the BDS-3 satellites in new frequency bands, and in order to maintain the consistency of the hybrid BDS-2 and BDS-3 orbit/clock products using the common B1IB3I data, the use of B1CB2a observations is not sufficient for both precise orbit determination (POD) and precise point positioning (PPP) applications. In this study, one-year data of 2022 from the International GNSS Service (IGS) and the International GNSS Monitoring and Assessment System (iGMAS) are used in the precise orbit and clock determination for BDS-3 satellites based on the two sets of observations (i.e., B1IB3I and B1CB2a), and the orbit and clock accuracy along with the PPP ambiguity resolution (AR) performance are investigated. In general, the validations demonstrate that clear improvement can be achieved for the B1CB2a-based solution for both POD and PPP. In comparison to the B1IB3I, using BDS-3 B1CB2a observations can help to improve orbit consistency by around 25% as indicated by orbit boundary discontinuities (OBDs), and this use can further reduce the bias and enhance the orbit accuracy as revealed by satellite laser ranging (SLR) residuals. Similar improvement was also identified in the satellite clock performance. The B1CB2a-based solution obtains decreased Allan deviation (ADEV) values in comparison with the B1IB3I-based solution by 6~12%. Regarding the PPP-AR performance, the advantage of B1CB2a observations is evidently reflected through the estimates of wide-lane/narrow-lane fractional cycle bias (FCB), convergence time, and positioning accuracy, in which a significant reduction over 10 min is found in the PPP convergence time.

environmental sciences,imaging science & photographic technology,remote sensing,geosciences, multidisciplinary
Analysis and Assessment of BDS‐3 Five Single‐Frequency Civilian Signals Single Point Positioning Considering Time Group Delay and Intersignal Correction

Xingli Sun

DOI: https://doi.org/10.1155/2024/5552343

IF: 1.4

2024-11-05

International Journal of Aerospace Engineering

Abstract:The BeiDou Global Navigation Satellite System (BDS‐3) has been providing global positioning, navigation, and timing (PNT) services for over 3 years. Single‐frequency single point positioning (SPP) receivers have significant advantages such as low hardware cost and easy implementation, making them widely used in engineering practice. The time group delay (TGD) and intersignal correction (ISC) are the main parameters for single‐frequency SPP and must be corrected. On‐orbit 30 BDS‐3 satellites have upgraded and maintained operation in 2022, while more multi‐GNSS experiment (MGEX) stations can simultaneously receive all five frequency civilian signals of BDS‐3, namely, B1I, B1C, B2a, B2b, and B3I. So now, it is worth assessing the SPP of BDS‐3 five single‐frequency civilian signals considering TGD and ISC corrections, respectively. Then, with 7 days of 73 MGEX stations simultaneously receiving all BDS‐3 five frequencies, GPS L1 and Galileo E1 civilian signals were selected, and the root mean square (RMS) error was used to assess the SPP performance. The BDS‐3 single‐frequency SPP static and kinematic results show that the order of accuracy from high to low is B1C, B1I, B3I, B2b, and B2a. More thorough static results reveal that B1C's RMS errors in the north, east, and up (NEU) three directions are 1.12, 0.41, and 1.78 m, respectively, and B1C outperforms B2a by 0.85, 0.28, and 1.23 m. More detailed kinematic results reveal that B1C's NEU RMS errors are 1.47, 0.77, and 2.72 m, respectively, and that B1C outperforms B2a by 1.04, 0.47, and 1.78 m. The single‐frequency SPP has a higher positioning accuracy at mid to high latitudes in the northern hemisphere than at mid to low latitudes in the southern. The single‐frequency SPP of BDS‐3 B1I is competitive with GPS L1 and Galileo E1. BDS‐3's five single‐frequency signals, GPS L1, and Galileo E1 all perform well in the east direction, while the up direction performs badly in static and kinematic modes.

engineering, aerospace
Analysis of BDS/GPS Signals’ Characteristics and Navigation Accuracy for a Geostationary Satellite

Meng Wang,Tao Shan,Wanwei Zhang,Hao Huan

DOI: https://doi.org/10.3390/rs13101967

IF: 5

2021-05-18

Remote Sensing

Abstract:The utilization of Global Navigation Satellite System (GNSS) is becoming an attractive navigation approach for geostationary orbit (GEO) satellites. A high-sensitivity receiver compatible with Global Position System (GPS) developed by the United States and BeiDou Navigation Satellite System (BDS) developed by China has been used in a GEO satellite named TJS-5 to demonstrate feasibility of real-time navigation. According to inflight data, the GNSS signal characteristics including availability, position dilution of precision (PDOP), carrier-to-noise ratio (C/N0), observations quantity and accuracy are analyzed. The mean number of GPS and GPS + BDS satellites tracked are 7.4 and 11.7 and the mean PDOP of GPS and GPS + BDS are 10.24 and 3.91, respectively. The use of BDS significantly increases the number of available navigation satellites and improves the PDOP. The number of observations with respect to C/N0 is illustrated in detail. The standard deviation of the pseudorange noises are less than 4 m, and the corresponding carrier phase noises are mostly less than 8 mm. We present the navigation performance using only GPS observations and GPS + BDS observations combination at different weights through comparisons with the precision reference orbits. When GPS combined with BDS observations, the root mean square (RMS) of the single-epoch least square position accuracy can improve from 32.1 m to 16.5 m and the corresponding velocity accuracy can improve from 0.238 m/s to 0.165 m/s. The RMS of real-time orbit determination position accuracy is 5.55 m and the corresponding velocity accuracy is 0.697 mm/s when using GPS and BDS combinations. Especially, the position accuracy in x-axis direction reduced from 7.24 m to 4.09 m when combined GPS with BDS observations.

environmental sciences,imaging science & photographic technology,remote sensing,geosciences, multidisciplinary
Comprehensive Analyses of PPP-B2b Performance in China and Surrounding Areas

Yan Liu,Cheng Yang,Mengni Zhang

DOI: https://doi.org/10.3390/rs14030643

IF: 5

2022-01-28

Remote Sensing

Abstract:BeiDou Global Navigation Satellite System (BDS-3) provides a regional Precise Point Positioning (PPP) service, called PPP-B2b, for users in China and surrounding areas through B2b signal transmitted from its three geostationary earth orbit (GEO) satellites. The information broadcasted by the B2b signal include satellite orbit corrections, satellite clock offset corrections, and differential code bias (DCB) corrections of BDS-3 satellites. In this study, the accuracies of PPP-B2b corrections along with real-time PPP performance are comprehensively evaluated referenced to precise orbit and clock products from GFZ and the precise DCB products from CAS. The result indicates that the accuracy of the BDS-3 broadcast orbit is similar to that of the PPP-B2b real-time orbit. The PPP-B2b clock offset correction improved the satellite clock offset precision of the BDS-3 broadcast ephemeris. The Signal-in-Space Range Error (SISRE) of broadcast ephemeris and PPP-B2b are calculated, which are 0.536 and 1.24 m, respectively. The large SISRE value of PPP-B2b is caused by the satellite-specified systematic bias to IGS final products. The positioning performance evaluation of real-time PPP with B2b service is carried out and compared with the real-time product provided by Wuhan University (WHU) based on the eight IGS MGEX stations in China and surrounding countries. The positioning accuracy of static positioning mode with PPP-B2b service achieved centimeter-level accuracy in the selected station, and that of kinematic positioning mode achieved decimeter-level accuracy. The availability rate of PPP-B2b corrections in the surrounding area of China, however, degrades from 88.76% to 60.91% in the selected stations. The accuracy of the PPP solution using PPP-B2b correction is better than that of using WHU real-time product within China. The positioning performance of stations located at the boundary of the PPP-B2b service area, however, is affected by the number of PPP-B2b available satellites. The positioning accuracy in kinematic positioning mode is worse than that of using WHU real-time precise product.

environmental sciences,imaging science & photographic technology,remote sensing,geosciences, multidisciplinary
Investigating the Global Performance of the BDS-2 and BDS-3 Joint Real-Time Undifferenced and Uncombined Precise Point Positioning Using RTS Products from Different Analysis Centers

Ahao Wang,Yize Zhang,Junping Chen,Hu Wang,Tianning Luo,Mingyou Gong,Quanpeng Liu

DOI: https://doi.org/10.3390/rs16050788

IF: 5

2024-02-25

Remote Sensing

Abstract:Compared to the traditional ionospheric-free (IF) precise point positioning (PPP) model, the undifferenced and uncombined (UU) PPP has the advantages of lower observation noise and the ability to obtain ionospheric information. Thanks to the IGS (International GNSS Service), real-time service (RTS) can provide RT vertical total electron content (VTEC) products, and an enhanced RT UU-PPP based on the RT-VTEC constraints can be achieved. The global performance of the BeiDou Navigation Satellite System-2 (BDS-2) and BDS-3 joint RT UU-PPP using different RTS products was investigated. There is not much difference in the RTS orbit accuracy of medium earth orbit (MEO) satellites among all analysis centers (ACs), and the optimal orbit accuracy is better than 5, 9, and 7 cm in the radial, along-track, and cross-track directions, respectively. The orbit accuracy of inclined geosynchronous orbit (IGSO) satellites is worse than that of MEO satellites. Except for CAS of 0.46 ns, the RTS clock accuracy of MEO satellites for other ACs achieves 0.2–0.27 ns, and the corresponding accuracy is about 0.4 ns for IGSO satellites. In static positioning, due to the limited accuracy of RT-VTEC, the convergence time of the enhanced RT UU-PPP is longer than that of RT IF-PPP for most ACs and can be better than 25 and 20 min in the horizontal and vertical components, respectively. After convergence, the 3D positioning accuracy of the static RT UU-PPP is improved by no more than 8.7%, and the optimal horizontal and vertical positioning accuracy reaches 3.5 and 7.0 cm, respectively. As for the kinematic mode with poor convergence performance, with the introduction of RT-VTEC constraints, the convergence time of RT UU-PPP can be slightly shorter and reaches about 55 and 60 min in the horizontal and vertical components, respectively. Both the horizontal and vertical positioning accuracies of the kinematic RT UU-PPP can be improved and achieve around 7.5 and 10 cm, respectively.

environmental sciences,imaging science & photographic technology,remote sensing,geosciences, multidisciplinary
BDS Multi-Frequency PPP Ambiguity Resolution with New B2a/B2b/B2a + B Signals and Legacy B1I/B3I Signals

Li Xin,Li Xingxing,Liu Gege,Yuan Yongqiang,Freeshah Mohamed,Zhang Keke,Zhou Feng

DOI: https://doi.org/10.1007/s00190-020-01439-8

IF: 4.809

2020-01-01

Journal of Geodesy

Abstract:As of December 2019, the core constellation of BeiDou Navigation Satellite System with global coverage (BDS-3) has been fully deployed with 24 MEO, 3 IGSO and 1 GEO satellites. In addition to the legacy B1I and B3I signals, BDS-3 satellites are capable of transmitting several new navigation signals, including B1C, B2a, B2b and B2a+b. The multi-frequency signals of BDS-3 bring new opportunities for fast ambiguity resolution (AR) of BDS precise point positioning (PPP). In this contribution, the BDS five-frequency PPP AR method was developed and the benefits of BDS-3 multi-frequency signals for precise positioning were investigated. The multi-frequency uncalibrated phase delay (UPD) products were estimated firstly using observations from 222 Multi-GNSS Experiment stations. The extra-wide-lane, wide-lane and narrow-lane UPDs of BDS-3 exhibit high stability with standard deviations less than 0.1 cycle. With the derived UPD products, five-frequency PPP AR was conducted at 12 static stations and a moving vehicle. The time to first fix of BDS PPP AR was shortened to 25.5 min with multi-frequency observations, showing improvement of 25.4% when compared to dual-frequency PPP AR. Moreover, instantaneous PPP wide-lane ambiguity resolution (WAR) can be achieved with success rate of over 90%. A fast decimeter-level accuracy can be achieved for BDS five-frequency PPP WAR with positioning accuracy improved by 68%-82% compared to PPP float solutions. The vehicle-borne experiment further demonstrates that BDS PPP WAR is potential to maintain decimeter-level positioning accuracy even in a complex environment.
Orbit determination, clock estimation and performance evaluation of BDS-3 PPP-B2b service

Chengpan Tang,Xiaogong Hu,Jinping Chen,Li Liu,Shanshi Zhou,Rui Guo,Xiaojie Li,Feng He,Jinhuo Liu,Jianhua Yang

DOI: https://doi.org/10.1007/s00190-022-01642-9

IF: 4.809

2022-08-31

Journal of Geodesy

Abstract:This paper focuses on PPP-B2b, one of the featured services for BDS-3, which provides users around China with centimetre-level static positioning accuracy and decimetre-level kinematic positioning accuracy by broadcasting precise corrections for GPS/BDS-3 satellites. The GEO PPP-B2b signal broadcasted information types, including the PRN mask, orbit corrections, differential code bias corrections and clock corrections, are introduced, as well as a brief description of their usage. A new orbit determination strategy using regional L-band code/phase measurements and inter-satellite link measurements in combination and a real-time clock estimation strategy based on the Kalman filter for PPP-B2b precise correction generation are introduced in this contribution. Then, the accuracy of the orbit and clock corrections is assessed. The orbit user ranging error (URE) is 0.05 m for the BDS-3 MEO and GPS satellites. The orbit URE for BDS-3 IGSO satellites is worse, i.e., 0.15 m. The clock correction accuracy is 0.2 ns for BDS-3 and GPS satellites. Finally, the PPP-B2b performance is validated by both the static PPP process and simulated kinematic PPP process. BDS-3/GPS dual-system PPP offers faster convergence and better accuracy. The positioning accuracy achievable using PPP-B2b real-time products is at the same level as that using post-processed products. The RMS for BDS-3/GPS dual-system static positioning errors is less than 1.0 cm in east and north and about 3.0 cm in the up. The simulated kinematic positioning accuracy is better than 2.5 cm in the north, 3.5 cm in the east and 8.5 cm in the up directions after convergence.

geochemistry & geophysics,remote sensing
High-precision services of BeiDou navigation satellite system (BDS): current state, achievements, and future directions

Weiguang GAO,Wei Zhou,Chengpan Tang,Xingxing Li,Yongqiang Yuan,Xiaogong Hu

DOI: https://doi.org/10.1186/s43020-024-00143-8

2024-06-25

Satellite Navigation

Abstract:With the rapid development of technologies such as autonomous driving and robotic navigation, the demand for accurate and reliable positioning results with BDS has increased. The current status and future development of BDS high precision services are reviewed. The operational PPP-B2b of BDS-3 achieves positioning accuracy at decimeter-level within 14 min and has the drawbacks in regional coverage and long convergence time compared with the international counterparts, such as CLAS of QZSS and HAS of Galileo. A development frame for multi-layer BDS high-precision services is proposed by considering its construction cost, compatibility of user terminal, operating maintenance burden, and service level. The global high-precision service with the improved orbit and clock accuracy enhanced with the inter-satellite link is taken as the most fundamental layer. By incorporating inter-satellite link observations, the orbit errors URE and clock errors are significantly reduced to approximately 0.05 m and 0.16 ns, respectively, which will expand PPP service to global. Based on this, the regional PPP-AR and PPP-RTK services with improved convergence performance are taken as the second layer. With PPP-AR, the convergence time drops to 10 min. With PPP-RTK, the convergence time would be further shortened to less than 3 min. The LEO enhanced PPP service is taken as the third layer which overcomes both drawbacks of the long convergence time of the inter-satellite link enhanced service (the first layer) and the regional coverage of the PPP-AR/PPP-RTK services (the second layer). The simulation results show that by introducing a LEO constellation of 288 satellites, the LEO enhanced PPP can achieve positioning accuracy better than 5 cm within approximately 1 min. In addition, the integration of LEO constellation and PPP-RTK is further proposed to enable instantaneous convergence. The implementation challenges are also presented.

remote sensing,engineering, aerospace,telecommunications
Design and implementation of a BDS precise point positioning service

Cheng Liu,Weiguang Gao,Tianxiong Liu,Dun Wang,Zheng Yao,Yang Gao,Xin Nie,Wei Wang,Dongjun Li,Weixing Zhang,Dongxia Wang,Yongnan Rao

DOI: https://doi.org/10.1002/navi.392

2020-10-09

Navigation

Abstract:<p>Precise point positioning (PPP) service is of great significance for BDS. The design and implementation of the service are presented. The PPP‐B2b signal of the service is constructed, which is efficient multiplexed with other signal components, and achieves compatibility between two service phases. A customized message format that can augment all visible satellites of four core constellations in mainland China is proposed. The high‐gain, 64‐ary, low‐density parity check (LDPC) coding is used, which facilitates the integrated design of the receivers. A signal quality test has revealed that the S‐curve bias (SCB) of PPP‐B2b does not exceed 0.0165 ns and the coherence between the code and the carrier of the signal is only 0.137. A performance evaluation has indicated that at its current stage, the positioning accuracy in the horizontal and vertical directions is better than 0.15 m and 0.3 m, respectively, and the convergence time does not exceed 800 s.</p>

[Comparison between productive and latent infection by measles virus in subacute panencephalitis].

Performance assessment of BeiDou B3-based real-time orbit determination for LEO satellites

Performance Evaluation of Precise Point Positioning for BeiDou-3 B1c/B2a Signals in the Global Range

Global precision analysis of carrier phase relative positioning in BeiDou navigation satellite system and United States global positioning system

Investigating Performance of BDS-2+3 Dual-Frequency Absolute Positioning With Broadcast Ephemerides, RTS and Final MGEX Products

Satellite availability and positioning performance of uncombined precise point positioning using BeiDou-2 and BeiDou-3 multi-frequency signals

Signal-in-space range error and positioning accuracy of BDS-3

Accuracy Analysis of BeiDou-3/GPS Real-Time Precise Common View Time Transfer Based on Carrier-Phase

Modeling and performance assessment of BDS-2/BDS-3 triple-frequency ionosphere-free and uncombined precise point positioning

Long-term performance analysis of BDS-3 precise point positioning (PPP-B2b) service

Modeling and performance assessment of precise point positioning with multi-frequency GNSS signals

Dual-frequency to five-frequency real-time precise point positioning using new BDS-3 PPP-B2b service

Advancing Precise Orbit Determination and Precise Point Positioning of BDS-3 Satellites from B1IB3I to B1CB2a: Comparison and Analysis

Analysis and Assessment of BDS‐3 Five Single‐Frequency Civilian Signals Single Point Positioning Considering Time Group Delay and Intersignal Correction

Analysis of BDS/GPS Signals’ Characteristics and Navigation Accuracy for a Geostationary Satellite

Comprehensive Analyses of PPP-B2b Performance in China and Surrounding Areas

Investigating the Global Performance of the BDS-2 and BDS-3 Joint Real-Time Undifferenced and Uncombined Precise Point Positioning Using RTS Products from Different Analysis Centers

BDS Multi-Frequency PPP Ambiguity Resolution with New B2a/B2b/B2a + B Signals and Legacy B1I/B3I Signals

Orbit determination, clock estimation and performance evaluation of BDS-3 PPP-B2b service

High-precision services of BeiDou navigation satellite system (BDS): current state, achievements, and future directions

Design and implementation of a BDS precise point positioning service