Abstract:With the rapid development of microelectronic technology, increasing wearable devices are available for us in daily lives. These wearable devices are usually powered by batteries, so the endurance of wearable devices is limited by battery capacity. Biomechanical energy harvesting (EH) is a promising approach to extend the endurance or replace batteries to power microelectronic devices. In this paper, we would first review the different types of EH devices and analyze the key technologies. Secondly, to compare the advantages and disadvantages of different EH devices, the design guidelines of the EH device is proposed. According to the design guidelines, an EH device with a weight of only 110 g is designed, which is lighter than the suspended-load backpack (38 kg) and the knee harvester (1.6 kg). Our EH device is able to convert the vibrations energy generated by the motion of lower limbs into electrical energy. Finally, to verify whether our EH device meets the design guidelines, three sets of experiment are conducted to evaluate the performance of the EH device. Experiment A is used to monitor the metabolic energy and electricity energy. According to experiment data, we calculate the COH and TCOH of EH device. The lowest COH and TCOH are 58 and 59, respectively. The TCOH of our EH device is higher than suspended-load backpack (30.7) and the knee harvester (13.6). Experiment B is used to test the adaptability of the EH device under the different conditions of terrains and walking speeds. The EH device is able to harvest energy in different terrains (up and down stair, at the treadmill with a slope of 0°, 5° and 10°) and at different speeds(4 km/h~8 km/h). The converted electrical power is up to 7.71 mW during walking at the speed of 8 km/h and is up to 5.28 mW when going up stairs. Experiment C is conducted to investigate the influence of the EH device on human motion by measuring the torque of the ankle, knee, and hip joints. When comparing the curves of torque, the EH device does not influence the biological moment of joints, indicating the EH device does not interfere with the movement. At the same time, another method to calculate the TCOH by calculating the net work done by the muscle in a gait cycle is proposed. When comparing the TCOH calculated by the metabolic energy with the TCOH calculated by the additional work done by the muscle, the results are basically the same. Meanwhile, the variation of the latter calculation result is smaller, indicating the method proposed by us is more precise.

A negative-work knee energy harvester based on homo-phase transfer for wearable monitoring devices

Ultralow-Frequency Biomechanical Energy Scavenging and Human Activity Recognition at Different Positions Using a Multifunctional Wearable Energy Harvester

A self-powered and self-sensing knee negative energy harvester

A Self‐Sensing and Self‐Powered Wearable System Based on Multi‐Source Human Motion Energy Harvesting

Active self-powered human motion assist system

A Non-Resonant Piezoelectric–Electromagnetic–Triboelectric Hybrid Energy Harvester for Low-Frequency Human Motions

Cooperative compliant traction mechanism for human-friendly biomechanical energy harvesting

A New Portable Energy Harvesting Device Mounted on Shoes: Performance and Impact on Wearer

A novel dual piezoelectric-electromagnetic energy harvester employing up-conversion technology for the capture of ultra-low-frequency human motion

An ultra-low-frequency, broadband and multi-stable tri-hybrid energy harvester for enabling the next-generation sustainable power

Development of a Biomechanical Energy Harvester

An Energy Harvester Coupled with a Triboelectric Mechanism and Electrostatic Mechanism for Biomechanical Energy Harvesting

A breathable and woven hybrid energy harvester with optimized power management for sustainably powering electronics

Circuit Designing for Charging Energy Storage Batteries with a Knee-joint Biomechanical Energy Harvester Aiming at the Optimal Total-Cost-of-Harvesting

Overview of Human Kinetic Energy Harvesting and Application

Electromechanical coupling of a 3.88 W harvester with circumferential step-size field: modeling, validation and self-powered wearable applications

Knee Energy Harvester with Variable Transmission to Reduce the Effect on the Walking Gait

Wearable Pendulum-Rotor-Separated Hybrid Generator for Smart Healthcare Monitoring

MP-HAR: A Novel Motion-Powered Real-Time Human Activity Recognition System

A Shoe-Embedded Piezoelectric Energy Harvester for Wearable Sensors

Harvest Human Kinetic Energy to Power Portable Electronics