Abstract:Chitin nanofibrils (NCh, ∼10 nm lateral size) were produced under conditions that were less severe compared to those for other biomass-derived nanomaterials and used to formulate high internal phase Pickering emulsions (HIPPEs). Pre-emulsification followed by continuous oil feeding facilitated a "scaffold" with high elasticity, which arrested droplet mobility and coarsening, achieving edible oil-in-water emulsions with internal phase volume fraction as high as 88%. The high stabilization ability of rodlike NCh originated from the restricted coarsening, droplet breakage and coalescence upon emulsion formation. This was the result of (a) irreversible adsorption at the interface (wettability measurements by the captive bubble method) and (b) structuring in highly interconnected fibrillar networks in the continuous phase (rheology, cryo-SEM, and fluorescent microscopies). Because the surface energy of NCh can be tailored by pH (protonation of surface amino groups), emulsion formation was found to be pH-dependent. Emulsions produced at pH from 3 to 5 were most stable (at least for 3 weeks). Although at a higher pH NCh was dispersible and the three-phase contact angle indicated better interfacial wettability to the oil phase, the lower interdroplet repulsion caused coarsening at high oil loading. We further show the existence of a trade-off between NCh axial aspect and minimum NCh concentration to stabilize 88% oil-in-water HIPPEs: only 0.038 wt % (based on emulsion mass) NCh of high axial aspect was required compared to 0.064 wt % for the shorter one. The as-produced HIPPEs were easily textured by taking advantage of their elastic behavior and resilience to compositional changes. Hence, chitin-based HIPPEs were demonstrated as emulgel inks suitable for 3D printing (millimeter definition) via direct ink writing, e.g., for edible functional foods and ultralight solid foams displaying highly interconnected pores and for potential cell culturing applications.

High internal phase Pickering emulsions stabilized by ε-poly-l-lysine grafted cellulose nanofiber for extrusion 3D printing

High internal phase Pickering emulsions stabilized by cellulose nanocrystals for 3D printing

Research Progress of Food-Grade High Internal Phase Pickering Emulsions and Their Application in 3D Printing

Ultrastable High Internal Phase Pickering Emulsions: Forming Mechanism, Processability, and Application in 3D Printing

Preparation of high internal phase Pickering emulsion gels stabilized by glycyrrhizic acid-zein composite nanoparticles: Gelation mechanism and 3D printing performance

High Internal Phase Emulsion for Food-grade 3D Printing Materials.

High internal phase Pickering emulsion stabilized by sea bass protein microgel particles: Food 3D printing application

Effects of Co-Assembly of Gliadin and Carboxymethyl Cellulose on the High Internal Phase Pickering Emulsions: Rheology Properties, 3D Printing Performance and Oil-Soluble Nutrient Delivery

Extrusion-based 3D printing of pickering high internal phase emulsions stabilized by flaxseed protein-sodium alginate complexes for encapsulating curcumin

High Internal Phase Pickering Emulsions Co-Stabilized by Zein Nanoparticles and Cellulose Nanocrystals: Fabrication, Characterization, and Application

Enhanced Printability of Food-Grade Edible Inks: Emulsions Formulated with Modified Pea Protein and Sodium Alginate

Food-grade Pickering emulsions and high internal phase Pickering emulsions encapsulating cinnamaldehyde based on pea protein-pectin-EGCG complexes for extrusion 3D printing

High Internal Phase Oil-in-Water Pickering Emulsions Stabilized by Chitin Nanofibrils: 3D Structuring and Solid Foam

High Internal Phase Emulsions Stabilized by Pea Protein Isolate-Inulin Conjugates: Application As Edible Inks for 3D Printing

High internal phase Pickering emulsion stabilized by zein-tannic acid-sodium alginate complexes: ll-Carotene loading and 3D printing

Pea protein/carboxymethyl cellulose complexes prepared using a pH cycle strategy as stabilizers of high internal phase emulsions for 3D printing

Fabrication of processable and edible high internal phase Pickering emulsions stabilized with gliadin/sodium carboxymethyl cellulose colloid particles

Protein-stabilized Pickering emulsion interacting with inulin, xanthan gum and chitosan: Rheological behavior and 3D printing

All-natural protein-polysaccharide conjugates with bead-on-a-string nanostructures as stabilizers of high internal phase emulsions for 3D printing

High internal phase emulsions stabilized by alkaline-extracted walnut protein isolates and their application in food 3D printing

Oil-water Interfacial Dual-Phase Synergistic Adsorption of Capsanthin-Cyanophycin in Gelatin Based High Internal Phase Emulsions for Multi-Nozzle 3D Printing