Abstract:Purpose: The authors have been using improved superelastic Nickel-Titanium alloy wire (ISW) to close and align extraction spaces simultaneously, instead of separately using rigid wires for closing extraction spaces and Ni-Ti alloy wires for leveling and aligning. ISW has a low stiffness, which makes it challenging to generate sufficient moments. This study aimed to demonstrate the forces and moments exerted on adjacent brackets using an orthodontic simulator (OSIM) attached to a high-precision 6-axis sensor. Materials and methods: In experiment 1, a 0.016 × 0.022-inch ISW, stainless steel (SS) wire, and β-titanium wires were ligatured into the two brackets. The 0.018 × 0.025-inch slot self-ligating brackets were bonded to two simulated teeth at the same height, and the experiment was conducted using the high-precision OSIM. The distance between the brackets was 10 mm, the V-bend angles of the installed wires were 10°, 20°, 30°, and 40°, and the apex position was set at the center of the bracket. In experiment 2, 6.0- and 9.0-mm long elastomeric chains were placed on the same brackets as in Experiment 1 to measure forces and moments. The distance between the brackets was increased by 1.0 mm from 6.0 to 15.0 mm. Both experiments were conducted in a 37 °C thermostatic chamber similar to the oral environment. Results and discussion: In experiment 1, we measured moments on both sides for all the wires. As the V-bend angle increased, the absolute values of the moments also increased. With a V-bend angle of 10°, there was a significant (p < 0.05) difference in the moment generated in the left and right brackets among the three wire types. In the ISW, -1.67 ± 0.38 N・mm was generated in the left bracket, while 0.38 ± 0.26 N・mm was generated in the right bracket at 10°. At 20°, -1.77 ± 0.69 N・mm was generated in the left bracket, while 2.37 ± 0.94 N・mm was generated in the right bracket. At 30°, -2.98 ± 0.49 N・mm was generated in the left bracket, while 3.25 ± 0.32 N・mm was generated in the right bracket. Moreover, at 40°, -3.96 ± 0.58 N・mm was generated in the left bracket, while 3.55 ± 0.53 N・mm was generated in the right bracket. Furthermore, in experiment 2, the moments increased in proportion to the increase in distance between the centers of the two brackets. Absolute values of the moments were approximately equal for the left and right brackets. The 6.0-mm elastomeric chain generated a minimum force of -0.09 ± 0.05 N in the left direction when the distance between brackets was 6.0 mm, while a maximum of 1.24 ± 0.3 N when the distance between brackets was 12 mm in the right bracket. In the left bracket, minimum and maximum forces of -0.09 ± 0.07 and 1.3 ± 0.4 N were generated in the right direction, respectively. The 9.0-mm elastomeric chain generated a minimum force of 0.03 ± 0.07 N in the left direction when the distance between brackets was 9.0 mm, while a maximum of 1.3 ± 0.1 N when the distance between brackets was 15 mm in the right bracket. In the left bracket, minimum and maximum forces of 0.05 ± 0.06 and 0.98 ± 0.2 N were generated in the right direction, respectively. Conclusion: Mechanical data of the ISW have been collected in the study, which was previously difficult to perform owing to the low stiffness of the wire. It is suggested that the ISW can provide sufficient moments with the addition of V-bends to close the space by bodily movement.

Mechanical analysis of the improved superelastic Ni-Ti alloy wire using the orthodontic simulator with high-precision sensors

Influence of Fluoride-Containing Acidic Artificial Saliva on the Mechanical Properties of Nickel-Titanium Orthodontics Wires.

[Comparison of Mechanical Properties on Different Phase Transformation Points of Nickel-Titanium Orthodontic Wires].

Influence of bracket-slot design on the forces released by superelastic nickel-titanium alignment wires in different deflection configurations

Load-deflection characteristics of superelastic and thermal nickel-titanium wires

The Eulerian buckling test for orthodontic wires

The Effect of Elastic and Metallic Ligation Methods on the Unloading Forces for Three Different Types of Nickel-Titanium Archwires Inserted Into Metallic Brackets: An In-vitro Study

Novel approach for characterizing clinical load application of superelastic orthodontic wires

Torque expression of superelastic NiTi V-Slot and conventional stainless steel orthodontic bracket-archwire combinations - A finite element analysis

Computational study on the effect of contact friction towards deactivation force of superelastic NiTi arch wire in a bracket system

Mechanical Properties and Potential Clinical Implications of Improved Superelastic Orthodontic Archwires: An Observational Study

In vitro biomechanical analysis of torque capabilities of various 0.018″ lingual bracket-wire systems: total torque play and slot size

Comparisons of nanoindentation, 3-point bending, and tension tests for orthodontic wires

Effect of Bracket Width on Bending Deformation of NiTi Arch Wire: A Finite Element Study

Stiffness and frictional resistance of a superelastic nickel-titanium orthodontic wire with low-stress hysteresis

Force-Controlled Biomechanical Simulation of Orthodontic Tooth Movement with Torque Archwires Using HOSEA (Hexapod for Orthodontic Simulation, Evaluation and Analysis)

THREE DIMENSIONAL MECHANICAL ANALYSIS FOR THE ORTHODONTIC FORCES OF ORTHODONTIC WIRES

Simulation of Orthodontic Force of Archwire Applied to Full Dentition Using Virtual Bracket Displacement Method

Mechanical Properties of Nickel-Titanium Archwire Used in the Final Treatment Phase of Tip-Edge Plus Technique: an in Vitro Study.

Evaluating the Elemental Composition, Transformation Behavior, Crystalline Structure, and Mechanical Properties of Three 0.016-Inch by 0.022-Inch Nickel-Titanium Archwires: An In Vitro Study

To Compare the Stress Magnitude on Roots of Mandibular Incisors at Different Inclinations With Different Arch Wires During Intrusion Mechanics—A Fem Study