MALIGNANT TRANSFORMATION OF SYRIAN HAMSTER EMBRYONIC CELLS WITH ROUS VIRUS OF THE SCHMIDT-RUPPIN STRAIN IN VITRO.

P. Veselý,J. Svoboda

Folia biologica

Abstract:

What problem does this paper attempt to address?

Hydrate-based adsorption-hydration hybrid approach enhances methane storage density in ZIF-8@AC

Guodong Zhang,Zhe Liu,Daming Liu,Yan Lin,Fei Wang

DOI: https://doi.org/10.1016/j.cej.2022.140503

IF: 15.1

2023-01-01

Chemical Engineering Journal

Abstract:The volume penalty of nano-porous materials causes low methane volumetric adsorption capacity, and the contradiction between it and gravimetric adsorption capacity limits the application of nano-porous materials in different scenarios. Here, we prepared a composite nano-porous material of ZIF-8@AC to bridge the gap using a synergistic approach of adsorption and hydration, and methane isothermal adsorption in wet ZIF-8@AC was evaluated under low temperature. Due to the hybrid effect of adsorption and hydration, methane storage capacity in the nano-porous material was enhanced. When 100 mg activated carbon was doped, methane gravimetric adsorption capacity in ZIF-8@AC increases by 6.78 % and 30.34 % comparing with that in parent AC and ZIF-8 separately. In addition, the formation of hydrate increases methane storage density in mesopores, macropores and intergranular pores, giving rise to large methane volumetric adsorption, which increases by 12.65 % and 53.24 % comparing with that in parent AC and ZIF-8, respectively. Moreover, hydration efficiency in confined pore space was investigated by differential scanning calorimetry (DSC), while a high-resolution electron microscope was applied to record hydrate morphologies. It was found that hydrate mainly forms in large pore spaces, and the enhanced intergranular pores serve as nanoreactors to significantly improve the hydration efficiency, which is greatly influenced by local water distribution. These findings provide a new strategy to enhance methane adsorption via adsorption and hydration hybrid approach and would shed light on the application of composite nano-porous materials in the adsorption of natural gas.

engineering, chemical, environmental
Adsorption-Hydration Sequence Method for Methane Storage in Porous Material Slurry

Jun-Li Chen,Peng Xiao,De-Xin Zhang,Guang-Jin Chen,Chang-Yu Sun,Qing-Lan Ma,Ming-Ke Yang,En-Bao Zou

DOI: https://doi.org/10.3389/fchem.2020.00294

IF: 5.5

2020-04-21

Frontiers in Chemistry

Abstract:Porous materials are deemed to be capable for promoting hydrate formation, while for the purpose of hydrate-based gas storage, those systems containing porous materials often cannot meet the requirement of high storage density. To increase the storage density, an adsorption-hydration sequence method was designed and systematically examined in this study. Methane storage and release in ZIF-8 slurries and fixed beds were investigated. The ZIF-8 retained 98.62%, while the activated carbon lost 62.17% of their adsorption capacities in slurry. In ZIF-8 fixed beds, methane storage density of 127.41 V/V<sub>bed</sub> was acquired, while the gas loss during depressurization accounted for 21.50% of the gas uptake. In the ZIF-8 slurry, the storage density was effectively increased with the adsorption-hydration sequence method, and the gas loss during depressurization was much smaller than that in fixed beds. In the slurry, the gas uptake and gas loss decreased with the decrease of the chilling temperature. The largest gas uptake and storage density of 78.84 mmol and 133.59 V/V<sub>bed</sub> were acquired in the slurry with ZIF-8 content of 40 wt.% at 268.15 K, meanwhile, the gas loss just accounted for 14.04% of the gas uptake. Self-preservation effect was observed in the slurry, and the temperature for the slowest gas release was found to be 263.15 K, while the release ratio at 10 h reached to 43.42%. By increasing the back pressure, the gas release rate could be effectively controlled. The gas release ratio at 1.1 MPa at 10 h was just 11.08%. The results showed that the application of adsorption-hydration sequence method in ZIF-8 slurry is a prospective manner for gas transportation.

chemistry, multidisciplinary
Production of green methane by carbon dioxide capture from landfill biogas via pressure swing adsorption mediated by MOF ZIF-8

Ammar Ali Abd,Jinsoo Kim,Dheyaa J. Jasim,Mohd Roslee Othman

DOI: https://doi.org/10.1016/j.enconman.2024.119090

IF: 10.4

2024-10-07

Energy Conversion and Management

Abstract:The growing interest in biomethane (bioCH 4 ) as a sustainable replacement for conventional fossil fuels highlights the urgency to develop efficient CO 2 capture methods from raw biogas, thereby enhancing the value of this renewable fuel source. This study investigates the efficacy of ZIF-8 as an adsorbent for CO 2 capture through pressure swing adsorption (PSA) under non-isothermal conditions. ZIF-8 was synthesized and characterized using SEM, BET, FTIR, and XRD to understand and confirm its microstructures. A computational model was developed to simulate the dynamic behavior of ZIF-8 during adsorption, incorporating insights from its characterization. The model, based on the extended Langmuir model for multicomponent adsorption, also accounted for adjustments in the adsorption bed geometry. Dynamic simulations were performed employing the Aspen Adsorption platform to assess the impact of key parameters such as the CH 4 /CO 2 ratio, length/diameter ratio, and adsorption time on bioCH 4 purity. Utilizing the Design of Experiments framework, central composite design (CCD), and desirability functions, the interplay of these parameters was optimized to enhance bioCH 4 purity and recovery rates. The optimized PSA system, utilizing ZIF-8, demonstrated impressive purity of 99.93% and recovery of 96.5% at CH 4 /CO 2 ratio of 2.06, a length/diameter ratio of 2.76, and an adsorption time of 115 s. These results meet stringent quality criteria for vehicle fuel, aligning with the most rigorous emission standards. For future investigations, it is crucial to explore the long-term stability and regeneration capabilities of ZIF-8 in large-scale applications. Understanding its practical feasibility and sustainability as an adsorbent for biogas upgrading will provide valuable insights for further advancements in this field.

energy & fuels,thermodynamics,mechanics
Hierarchically Porous Mg-MOF-74/Sodium Alginate Composite Aerogel for CO 2 Capture

Xiaoqian Peng,Jing Zhang,Jinqiang Sun,Xiaochan Liu,Xinfu Zhao,Shimo Yu,Zhipeng Yuan,Sijia Liu,Xibin Yi

DOI: https://doi.org/10.1021/acsanm.3c02916

IF: 6.14

2023-09-05

ACS Applied Nano Materials

Abstract:One of the most promising methods for capturing carbon dioxide (CO2) is solid physical adsorption, which is an efficient and simple technique. The key to effective CO2 capture is the development of high-performance solid adsorbents with excellent CO2 adsorption capacity, CO2/N2 selectivity, and rapid adsorption/desorption kinetics. In this paper, a Mg-MOF-74/sodium alginate composite aerogel was prepared by loading Mg-MOF-74 on sodium alginate sheets followed by directional freeze-drying. The composite aerogel exhibited a hierarchical porous structure, in which sodium alginate provided an open mesoporous/macroporous structure that promoted diffusion and contact with the active center of CO2. The Mg-MOF-74 micropores/mesopores promoted the strong interaction between CO2 and the adsorbent in the micropore and rapid mass transfer of CO2 to the adsorbent through the mesopores. The experimental data showed that MSA-6 achieved CO2 adsorption of 2.461 mmol·g–1 at 298 K. Furthermore, the CO2/N2 adsorption selectivity of MSA-6 reached 35.108, indicating its strong CO2 selective adsorption potential.

materials science, multidisciplinary,nanoscience & nanotechnology
ZrBDC-Based Functional Adsorbents for Small-Scale Methane Storage Systems

Olga V. Solovtsova,Ilya E. Men’shchikov,Andrey V. Shkolin,Anatoly A. Fomkin,Elena V. Khozina,Andrey A. Shiryaev

DOI: https://doi.org/10.1155/2022/4855466

2022-01-30

Abstract:Metal-organic frameworks (MOF), potentially porous coordination structures, are envisioned for adsorption-based natural gas (ANG) storage, including mobile applications. The factors affecting the performance of the ANG system with a zirconium-based MOF with benzene dicarboxylic acid as a linker (ZrBDC) as an adsorbent were considered: textural properties of the adsorbent and thermal effect arising upon adsorption. The high-density ZrBDC-based pellets were prepared by mechanical compaction of the as-synthesized MOF powder at different pressures from 30 to 240 MPa at 298 K without a binder and mixed with polymer binders: polyvinyl alcohol (PVA) and carboxyl methylcellulose (CMC). The structural investigations revealed that the compaction of ZrBDC with PVA under 30 MPa was optimal to produce the ZrBDC-PVA adsorbent with more than a twofold increase in the packing density and the lowest degradation of the porous structure. The specific total and deliverable volumetric methane storage capacities of the ZrBDC-based adsorbents were evaluated from the experimental data on methane adsorption measured up to 10 MPa and within a temperature range from 253 to 333 K. It was measured experimentally that at 253 K, an 100 mL adsorption tank loaded with the ZrBDC-PVA pellets exhibited the deliverable methane storage capacity of 172 m3(NTP)/m3 when the pressure dropped from 10 to 0.1 MPa. The methane adsorption data for the ZrBDC powder and ZrBDC-PVA pellets were used to calculate the important thermodynamic characteristic of the ZrBDC/CH4 adsorption system—the differential molar isosteric heat of adsorption, which was used to evaluate the state thermodynamic functions: entropy, enthalpy, and heat capacity. The initial heats of methane adsorption in powdered ZrBDC evaluated from the experimental adsorption isosteres were found to be ~19.3 kJ/mol, and then these values in the ZrBDC/CH4 system decreased at different rates during adsorption. In contrast, the heat of methane adsorption onto the ZrBDC-PVA pellets increased from 19.4 kJ/mol to a maximum with a magnitude, width, and position depended on temperature, and then it fell. The behaviors of the thermodynamic state functions of the ZrBDC/CH4 adsorption system were interpreted as a variation in the state of adsorbed molecules determined by a ratio of CH4-CH4 and CH4-ZrBDC interactions. The heat of adsorption was used to calculate the temperature changes of the ANG systems loaded with ZrBDC powder and ZrBDC pellets during methane adsorption under adiabatic conditions; the maximum integrated heat of adsorption was found at 273 K. The maximum temperature changes of the ANG system with the ZrBDC materials during the adsorption (charging) process did not exceed 14 K that are much lower than those reported for the systems loaded with activated carbons. The results obtained are of direct relevance for designing the adsorption-based methane storage systems for the automotive industry, developing new gas-power robotics systems and uncrewed aerial vehicles.

engineering, chemical,chemistry, applied, physical
Carbon adsorbents for methane storage: genesis, synthesis, porosity, adsorption

Ilya Men’shchikov,Andrey Shiryaev,Andrey Shkolin,Vladimir Vysotskii,Elena Khozina,Anatoly Fomkin

DOI: https://doi.org/10.1007/s11814-020-0683-2

IF: 2.7

2021-02-01

Korean Journal of Chemical Engineering

Abstract:Adsorbed natural gas (ANG) storage systems are based on nanoporous adsorbents with a tailored porous structure. Activated carbons are among the most promising and widely used candidates for this application, which is explained by the availability and abundance of raw material resources. In the present work, several series of activated carbons prepared from various precursors (coconut shell, peat, polymers, silicon carbide, and mineral coal) by different routes of physical and thermochemical activation were considered in the context of the adsorbed natural gas storage applications. Based on the Dubinin theory of volume filling of micropores and BET method, the porous structure of these adsorbents was evaluated from standard adsorption isotherms. The XRD, SAXS, and SEM measurements revealed variations in the textural and morphological properties of the adsorbents and their dependence on the precursor and synthesis procedure. The pore sizes evaluated from the adsorption and SAXS data were compared. Experimental data on methane adsorption at the temperature of 303 K and pressures of 0.1, 3.5, and 10 MPa made it possible to identify the most effective adsorbents. It was shown that the adsorption properties of ACs prepared from peat and mineral coal are determined by surface chemistry inherited from the precursor and activating agent. In contrast, the adsorption performance of ACs from polymer and coconut shell depends solely on the pore volume and pore dimensions. The adsorption effectiveness of each AC varies with pressure as a function of textural properties. Thus, a selection of an optimal adsorbent should be adjusted for thermodynamical coditions of ANG system.

engineering, chemical,chemistry, multidisciplinary
Pyrolytic aerogels with tunable surface groups for efficient methane solidification storage via gas hydrates

Changrui Shi,Shuai Wang,Huiquan Liu,Lunxiang Zhang,Mingjun Yang,Yongchen Song,Jiafei Zhao,Zheng Ling

DOI: https://doi.org/10.1016/j.fuel.2022.125716

IF: 7.4

2023-01-01

Fuel

Abstract:Gas hydrate, composed of water molecule cages, is promising for safe and sustainable gas storage with minor energy consumption. However, the practical utilization of hydrate-based technologies is hindered by the sluggish formation kinetics of gas hydrate. Central to the challenge of utilizing hydrate-based gas storage is developing effective promoters and improving the understanding of the complicated interplay between a promoter’s structure and chemical composition. Herein, we reported a simple and scalable strategy to produce pyrolytic composite aerogels assembled from vermiculite nanosheets and sodium alginate as efficient promoters for the methane hydrate formation. Benefiting from the high specific surface area and finely tuned surface functional groups, the as-made aerogels significantly improve methane hydrate formation kinetics with high storage capacity and excellent cycling stability. It is found that the phase change process of water to methane hydrate conversion can be controlled by adjusting the content of carbonyl and hydroxyl groups of the as-made aerogels. Raman spectra were used to elucidate the molecular mechanisms for the enhanced methane hydrate formation due to the interaction between oxygen-containing surface functional groups and water molecules close to used aerogels. This work not only provides an effective way to fabricate aerogel-based promoters for methane hydrate formation but also sheds light on the underlying mechanism of the surface composition dependent performance for improving gas hydrate formation.

energy & fuels,engineering, chemical
Methionine Aqueous Solution Loaded Vermiculite/mxene Aerogels for Efficient CO2 Storage Via Gas Hydrate

Shuai Wang,Changrui Shi,Huiquan Liu,Lunxiang Zhang,Jiafei Zhao,Yongchen Song,Zheng Ling

DOI: https://doi.org/10.1016/j.fuel.2022.126833

IF: 7.4

2023-01-01

Fuel

Abstract:Gas hydrate provides an ideal way for CO2 capture and storage using water by forming cages via an environment -friendly and energy-efficient hydrate formation process. However, the practical utilization and upscaling of hydrate-based gas storage are impeded by the slow formation kinetics of gas hydrate due to the limited multi-phase interface for mass transfer and reaction. Herein, we demonstrated a simple strategy to fabricate composite aerogels assembled of natural vermiculite and MXene nanosheets as the ideal substrate for boosting CO2 hydrate formation. The structure and surface compositions of vermiculite/MXene composite aerogels were analyzed by XRD, FT-IR, SEM, and XPS. It shows that monolithic pore structures and surface functional groups can be finely tuned by controlling the mass ratio of vermiculite and MXene, leading to an outstanding CO2 storage capacity of 136.9 v/v (corresponding to 0.121 mol CO2/mol water) with enhanced hydrate formation kinetics. The degree of water saturation plays the most vital role in controlling formation kinetics and gas storage capacity. This work provides a reliable method to synthesize aerogels for boosting CO2 storage via enhanced hydrate formation and sheds light on the structure performance relationship of porous materials for enhancing gas hydrate formation.
Highly Efficient Separation of Methane from Nitrogen on a Squarate‐based Metal‐organic Framework

Liangying Li,Lifeng Yang,Jiawei Wang,Zhiguo Zhang,Qiwei Yang,Yiwen Yang,Qilong Ren,Zongbi Bao

DOI: https://doi.org/10.1002/aic.16335

IF: 4.167

2018-01-01

AIChE Journal

Abstract:Highly selective capture of methane from nitrogen is considered to be a feasible approach to improve the heating value of methane and mitigate the effects of global warming. In this work, an ultramicroporous squarate‐based metal‐organic framework (MOF), [Co3(C4O4)2(OH)2] (C4O42− = squarate), with enhanced negative oxygen binding sites was synthesized for the first time and used as adsorbent for efficient separation of methane and nitrogen. Adsorption performance of this material was evaluated by single‐component adsorption isotherms and breakthrough experiments. Furthermore, density functional theory calculation was performed to gain the deep insight into the adsorption binding sites. Compared with the other state‐of‐the‐art materials, this material exhibited the highest adsorption selectivity (8.5–12.5) of methane over nitrogen as well as the moderate volumetric uptake of methane (19.81 cm3/cm3) under ambient condition. The unprecedented selectivity and chemical stability guaranteed this MOF as a candidate adsorbent to capture CH4 from N2, especially for the unconventional natural gas upgrading. © 2018 American Institute of Chemical Engineers AIChE J, 64: 3681–3689, 2018
Novel vermiculite/tannic acid composite aerogels with outstanding CO 2 storage via enhanced gas hydrate formation

Shuai Wang,Huilian Sun,Huiquan Liu,Dezhi Xi,Jiayi Long,Lunxiang Zhang,Jiafei Zhao,Yongchen Song,Changrui Shi,Zheng Ling

DOI: https://doi.org/10.1016/j.energy.2023.130033

IF: 9

2023-12-24

Energy

Abstract:Gas hydrate-based CO 2 storage, using only water cages, provides an environmentally friendly and energy-efficient solution to reduce greenhouse gas emissions. However, the sluggish formation kinetics of gas hydrate is hindered by the limited reaction interfaces , thereby impeding the practical utilization of hydrate-based greenhouse gas storage. Herein, we reported a novel strategy to fabricate natural vermiculite and tannic acid composite aerogels as the effective substrates for boosting CO 2 hydrate formation. The results show that the formation kinetics of CO 2 hydrate in the aerogels exhibits composition dependence and an outstanding CO 2 storage capacity of 130.1 v/v (corresponding to 0.114 mol CO 2 /mol water). Inverse gas chromatography was used to analyze the surface energy and its components of the aerogels. Raman spectra and nuclear magnetic resonance were used to unravel the water molecule assembly and states. The CO 2 uptake capacity can be further improved by compressing the aerogel to 75 % of the original volume, showing an impressive storage capacity of 146.8 v/v. The as-made aerogels demonstrated outstanding cycle stability and short induction time for CO 2 hydrate formation. The results of this study pave the way for designing effective CO 2 hydrate promoters and facilitating promising CO 2 capture and storage technologies via gas hydrate.

energy & fuels,thermodynamics
Novel Vermiculite/tannic Acid Composite Aerogels with Outstanding CO2 Storage Via Enhanced Gas Hydrate Formation

Shuai Wang,Huilian Sun,Huiquan Liu,Dezhi Xi,Jiayi Long,Lunxiang Zhang,Jiafei Zhao,Yongchen Song,Changrui Shi,Zheng Ling

DOI: https://doi.org/10.1016/j.energy.2023.130033

IF: 9

2024-01-01

Energy

Abstract:Gas hydrate-based CO2 storage, using only water cages, provides an environmentally friendly and energy-efficient solution to reduce greenhouse gas emissions. However, the sluggish formation kinetics of gas hydrate is hindered by the limited reaction interfaces, thereby impeding the practical utilization of hydrate-based greenhouse gas storage. Herein, we reported a novel strategy to fabricate natural vermiculite and tannic acid composite aerogels as the effective substrates for boosting CO2 hydrate formation. The results show that the formation kinetics of CO2 hydrate in the aerogels exhibits composition dependence and an outstanding CO2 storage capacity of 130.1 v/v (corresponding to 0.114 mol CO2/mol water). Inverse gas chromatography was used to analyze the surface energy and its components of the aerogels. Raman spectra and nuclear magnetic resonance were used to unravel the water molecule assembly and states. The CO2 uptake capacity can be further improved by compressing the aerogel to 75 % of the original volume, showing an impressive storage capacity of 146.8 v/v. The as-made aerogels demonstrated outstanding cycle stability and short induction time for CO2 hydrate formation. The results of this study pave the way for designing effective CO2 hydrate promoters and facilitating promising CO2 capture and storage technologies via gas hydrate.
Carbon Material-Based Aerogels for Gas Adsorption: Fabrication, Structure Design, Functional Tailoring, and Applications

Lianming Zhang,Yu Lei,Peng He,Hao Wu,Lei Guo,Gang Wei

DOI: https://doi.org/10.3390/nano12183172

IF: 5.3

2022-09-13

Nanomaterials

Abstract:Carbon material-based aerogels (CMBAs) have three-dimensional porous structure, high specific surface area, low density, high thermal stability, good electric conductivity, and abundant surface-active sites, and, therefore, have shown great application potential in energy storage, environmental remediation, electrochemical catalysis, biomedicine, analytical science, electronic devices, and others. In this work, we present recent progress on the fabrication, structural design, functional tailoring, and gas adsorption applications of CMBAs, which are prepared by precursor materials, such as polymer-derived carbon, carbon nanotubes, carbon nanofibers, graphene, graphene-like carbides, fullerenes, and carbon dots. To achieve this aim, first we introduce the fabrication methods of various aerogels, and, then, discuss the strategies for regulating the structures of CMBAs by adjusting the porosity and periodicity. In addition, the hybridization of CMBAs with other nanomaterials for enhanced properties and functions is demonstrated and discussed through presenting the synthesis processes of various CMBAs. After that, the adsorption performances and mechanisms of functional CMBAs towards CO2, CO, H2S, H2, and organic gases are analyzed in detail. Finally, we provide our own viewpoints on the possible development directions and prospects of this promising research topic. We believe this work is valuable for readers to understand the synthesis methods and functional tailoring of CMBAs, and, meanwhile, to promote the applications of CMBAs in environmental analysis and safety monitoring of harmful gases.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology,chemistry
Hydrate-based adsorption-hydration hybrid approach enhances methane storage in wet MIL-101(Cr)@AC under mild condition

Guodong Zhang,Zhe Liu,Yaning Kong,Fei Wang

DOI: https://doi.org/10.1016/j.cej.2023.145068

IF: 15.1

2023-09-01

Chemical Engineering Journal

Abstract:Hydrate-based adsorption and hydration natural gas (AHNG) technology was reported to achieve large methane storage density under mild conditions. In order to enhance methane uptake, a composite nano porous material of MIL-101(Cr)@AC was prepared through fluorine-free hydrothermal reaction, and methane adsorption isotherms for both dry and wet samples were measured under hydrate favorable conditions. Hydrate in-situ formation loaded by the composite material was also carried out, while hydrate kinetics was evaluated by Raman spectrum. It was found that MIL-101(Cr) remains cubic symmetric structure when activated carbon (AC) was doped, but its size decreases with the increase in AC doping amount, while the specific surface area and pore volume significantly increase, and this enhances methane adsorption that increases by 65.58%. More enhanced methane uptake was obtained when wet sample was applied due to adsorption and hydration synergy, wherein methane physical adsorption ability remains, while formed hydrate stores extra methane. The contribution of hydrate to methane uptake is up to 40%, so large methane storage density is anticipated, methane volumetric uptake is up to 179.3 V/V under a mild condition (9.3 MPa and 274.15 K), which increases by 38.03%. Compared with our recently reported ZIF-8@AC, methane storage capacity in this new material increases by 36.5% (Chem. Eng. J., 2023, 455, 140503). In addition, hydrate progressive growth with the increase in adsorption pressure was observed, the area ratio of hydrate large cages to small one finally approaches to the theoretical value of 3:1, suggesting approximately complete conversion of pre-adsorbed water.

engineering, chemical, environmental
Efficient CO2 Capture by ZIF-8-derived In-Situ Nitrogen-Doped Nanoporous Carbon with Ultra-High Selectivity and Stability

Shuqin Zhang,Jieni Wang,Chenlin Wei,Peiliang Liu,Shumeng Qin,Leichang Cao,Yanmei Zhou,Jinglai Zhang,Shicheng Zhang

DOI: https://doi.org/10.1016/j.jece.2024.114839

IF: 7.7

2024-01-01

Journal of Environmental Chemical Engineering

Abstract:Global warming and the increasing frequency of extreme weather caused by the gradual increase in CO2 concentration in the atmosphere are urgent issues that must be addressed. In this study, ZIF-8-derived in-situ nitrogen-doped porous carbon materials were prepared through one-step pyrolysis of ZIF-8. The synthesis was gradually optimized by exploring different pyrolysis temperatures to determine the optimal ZIF-8-derived porous carbon for CO2 adsorption. The CO2-adsorption capacity of ZIF-8-800 reached 5.22 and 6.19mmolg-1 at 25 ℃ and 0 ℃ (1bar), respectively. After five cycles, its CO2-adsorption capacity decreased by only about 1.7%. Moreover, the CO2/N2 selectivity at 1bar was as high as 21.2 (48.9 at 0.05bar), and the isothermal adsorption heat was also within a moderate range (31kJmol-1). The superior CO2 adsorption performance was found to originate from the comprehensive effect of the three-dimensional pore structure that combined reasonably coordinated micropores, mesopores, and macropores, as well as some specific favorable N/O groups. The results indicate the broad application prospects of ZIF-8-Ts in CO2 capture and separation and provide new ideas for the sustainable application of novel MOF-derived porous carbon materials.
Experimental study on synergistic promotion of reciprocating impact and porous materials on methane capture based on hydrate method

Jintao Hu,Naihao Chen,Zhi Li,Nan Li,Jingyu Kan,Tianduo Li,Guangjin Chen

DOI: https://doi.org/10.1016/j.cej.2024.149137

IF: 15.1

2024-02-03

Chemical Engineering Journal

Abstract:The gas storage technology based on the hydrate method has the advantages of safety, economy and high efficiency, but it also has some disadvantages including harsh thermodynamic conditions and slow formation rate. To achieve satisfactory gas storage capacity and shorten the hydrate reaction time, the reciprocating impact and porous materials (i.e. ZIF-8 and activated carbon) are combined in this work to solve the problem of low mass transfer rate or conversion ratio caused by a single method. The experimental results indicate that under the reciprocating impact, adding a small amount of ZIF-8 or activated carbon particles in water can improve the methane capture capacity of hydrate when the initial pressure is less than 5 MPa, and shorten the equilibrium time of the reaction at high pressure. And the overall effect of adding ZIF-8 particles is better than that of adding 100-mesh and 400-mesh activated carbon particles. Moreover, it is found that the presence of ZIF-8 particles moderates the hydrate formation environment, so that the hydrate can still maintain a high reaction rate under low pressure. Under high pressure, in the middle and later stages of hydration reaction, ZIF-8 can fluff up the hydrate blocks and create certain gaps on the formed hydrate shell. The fluffy hydrate blocks increase the capillary effect and provide more gas–liquid-solid contact points. The gaps created by ZIF-8 on the hydrate shell accelerates the flow of methane gas through the hydrate shell and reacts with the water enclosed in the hydrate shell to convert into hydrates.

engineering, chemical, environmental
Microporous MOF-5@AC and Cu-BDC@AC Composite Materials for Methane Storage in ANG Technology

Niloufar Yadavar Nikravesh,Mojtaba Beygzadeh,Mehrdad Adl

DOI: https://doi.org/10.1155/2023/2282746

IF: 4.6

2023-02-03

International Journal of Energy Research

Abstract:Novel composites (MOF-5 and Cu-BDC) based on economically activated carbon have been developed to investigate methane adsorption capacity for ANG applications. The composites were synthesized by adding MOFs precursor in two different weight percent (10% and 40%) to commercial activated carbon under solvothermal conditions (110-120°C). The synthesized adsorbents were characterized by FT-IR, XRD, SEM, EDS, and BET techniques to gather information about their crystallinity, morphology, and specific surface area. A methane uptake measurement system based on the volumetric method was made to obtain methane adsorption capacity on each composite. Then, the amount of methane adsorption for each one was calculated, and the experimental data were compared with different isotherm adsorption models appropriate for gas adsorption, including Langmuir, Freundlich, and Dubinin-Radushkevich. This comparison showed that the best fitting belonged to the Langmuir isotherm model. Also, stability and kinetic studies were done for two MOF-540% @AC and Cu-BDC40% @AC composites. In the kinetics study, experimental data were compared and analyzed in terms of pseudo-first order, pseudo-second order, and intraparticle diffusion models. The kinetics study showed that methane adsorption happens very fast on the synthesized adsorbents. The amount of methane adsorption at 35 bar and room temperature for pure activated carbon was specified as 4.32 mmol/g. The 10% and 40% of Cu-BDC with activated carbon are 5.59 mmol/g and 6.85 mmol/g, respectively. The capacity of MOF-510% @AC and MOF-540% @AC composites were obtained at 5.9 mmol/g and 7.3 mmol/g, respectively. Increasing methane uptake (70%) was obtained by adding 40 wt.% of MOF-5 to commercial activated carbon.

energy & fuels,nuclear science & technology
Changes and challenges in sustainability of technical and vocational education and training — teacher education programme: A case study

J. Yunos,L. Sern,N. Hamdan

DOI: https://doi.org/10.1109/ICEED.2016.7856099

2016-12-01

Abstract:In employment, increasing participation within the unchanging workforce with current structure may lead to a decrease in sustainability. Meanwhile in education, the sustainability of a program is mainly influenced by the association of all stakeholders. The stakeholders are referred to as the institutions, industries, government and community. In order to achieve sustainability, changes and challenges related to those stakeholders cannot be avoided. This paper investigates how the Technical and Vocational Education and Training (TVET) Teacher Education Program in Malaysia can be sustained in the 21st Century. A case study has been conducted to look into the changes and challenges faced by the stakeholders. The data collection process comprised four semi-structured interviews with the experts in TVET Teacher Education Program. The findings from the case study indicated that the challenges faced by the stakeholders are inclusive of teachers' attitude towards learning; the perception of the society on TVET as the second class education; lack of partnership between the institutions and the industries; and lack of pragmatic policies in improving the quality of TVET Teacher Education Program.
Methane Storage and Purification of Natural Gas in Metal‐Organic Frameworks

Wenpeng Xie,Qiuju Fu,Lingzhi Yang,Liting Yan,Jun Zhang,Xuebo Zhao

DOI: https://doi.org/10.1002/cssc.202401382

IF: 8.4

2024-08-31

ChemSusChem

Abstract:Natural gas, primarily composed of methane (CH4), represent an excellent choice for a potentially sustainable renewable energy transition. However, the process of compressing and liquefying CH4 for transport and storage typically results in significant energy losses. In addition, in order to optimize its efficacy as a fuel, the CH4 content of natural gas needs to be increased to a level of at least 97% to ensure its quality and efficiency in various applications. Metal‐organic frameworks (MOFs) represent a novel category of porous materials that possess exceptional capability in modifying pore size and chemical environment, making them ideally suited for the storage of CH4 and the adsorption of propane (C3H8), ethane (C2H6), carbon dioxide (CO2), nitrogen (N2), and hydrogen sulfide (H2S) to facilitate the purification process of CH4 from natural gas. In this paper, we systematically summarize the mechanism by which MOF materials facilitate the storage of CH4 and the purification of CH4 from natural gas, leveraging the structural characteristics inherent to MOF materials. The focus of further research should also be directed towards the investigation of CH4 storage by flexible MOFs, the resolution of the trade‐off dilemma, and the commercial application of MOFs.

chemistry, multidisciplinary,green & sustainable science & technology
Microporous Carbon Adsorbents Prepared by Activating Reagent-Free Pyrolysis for Upgrading Low-Quality Natural Gas

Fuqiang Chen,Zhiguo Zhang,Qiwei Yang,Yiwen Yang,Zongbi Bao,Qilong Ren

DOI: https://doi.org/10.1021/acssuschemeng.9b05627

IF: 8.4

2019-01-01

ACS Sustainable Chemistry & Engineering

Abstract:Separation of methane and nitrogen is an essential matter of concern in upgrading low-quality natural gases such as biogas, coalbed methane, shale gas, and so forth. However, similar weak polarities and the close kinetic diameter of methane and nitrogen make the separation of these two species very challenging. Considering that micropores play an extremely important role in adsorption selectivity, in this work, carbon adsorbents with homogeneous pore widths were controllably prepared from poly(vinylidene chloride) resins by activating reagent-free pyrolysis. Compared to traditional activated carbon prepared by pyrolysis with the presence of chemical reagents such as potassium hydroxide and zinc chloride, the obtained microporous carbon adsorbents are free of mesopores and macropores and demonstrate efficient separation of CH4 and N-2. These materials were comprehensively characterized by PXRD, SEM, TEM, TGA, XPS, Raman spectra, contact angle measurement, and water vapor adsorption. The synthesized carbon adsorbents have an ultrahigh specific surface area (>1100 m(2)) and a large micropore volume (>0.37 cm(3)/g). Adsorption performances of these materials were demonstrated by static adsorption tests and breakthrough experiments. The methane uptake up to 1.57 mmol/g at ambient conditions outperforms most top-performing adsorbents reported to date. Moreover, the optimal microporous carbon, denoted C-PVDC-700, exhibits the highest LAST selectivity (5.5-14.7 at 298 K) of methane over nitrogen. The facile preparation strategy, ultrahigh adsorption capacities, record-high selectivity, and robust stability guarantee that this material is promising for upgrading low-quality natural gas.
Porous MOFs with geometric mismatch between trimers and octatopic pyrene-based ligands for low-temperature methane storage

Kun Wang,Honghao Cao,Yuanlong Zhong,Zhenning Yang,Hancheng Shi,Zhangyi Xiong,Yuqiao Mu,Zhijie Chen

DOI: https://doi.org/10.1039/d4cc04907a

IF: 4.9

2024-12-04

Chemical Communications

Abstract:Natural gas is recognized as a transitional clean energy fuel to address a variety of environmental problems. Identifying porous adsorbents with high-capacity low-temperature methane adsorption performances is crucial for advancing next-generation technologies for efficiently utilizing boil-off gas, inevitablely generated from liquefied natural gas systems. Herein, we synthesized highly porous metal–organic frameworks (MOFs)-TBPP-MOFs with a geometric mismatch strategy by combining seemingly incompatible trinuclear clusters with octatopic pyrene-based ligands. The Cr-TBPP-MOF achieves a high apparent Brunauer–Emmett–Teller (BET) surface area of 3700 m 2 g −1 and demonstrates pore volumes of 1.31 cm 3 g −1 at P / P 0 = 0.9. Consequently, under the LNG–ANG coupling operation conditions, Cr-TBPP-MOF exhibits a high low-temperature methane uptake of 335 cm 3 (STP) cm −3 at 159 K and 10 bar with a working capacity of 302 cm 3 (STP) cm −3 between 6 bar and 159 K to 5 bar and 298 K, positioning it as a promising candidate material for low-temperature methane adsorption.

chemistry, multidisciplinary

MALIGNANT TRANSFORMATION OF SYRIAN HAMSTER EMBRYONIC CELLS WITH ROUS VIRUS OF THE SCHMIDT-RUPPIN STRAIN IN VITRO.

Hydrate-based adsorption-hydration hybrid approach enhances methane storage density in ZIF-8@AC

Adsorption-Hydration Sequence Method for Methane Storage in Porous Material Slurry

Production of green methane by carbon dioxide capture from landfill biogas via pressure swing adsorption mediated by MOF ZIF-8

Hierarchically Porous Mg-MOF-74/Sodium Alginate Composite Aerogel for CO 2 Capture

ZrBDC-Based Functional Adsorbents for Small-Scale Methane Storage Systems

Carbon adsorbents for methane storage: genesis, synthesis, porosity, adsorption

Pyrolytic aerogels with tunable surface groups for efficient methane solidification storage via gas hydrates

Methionine Aqueous Solution Loaded Vermiculite/mxene Aerogels for Efficient CO2 Storage Via Gas Hydrate

Highly Efficient Separation of Methane from Nitrogen on a Squarate‐based Metal‐organic Framework

Novel vermiculite/tannic acid composite aerogels with outstanding CO 2 storage via enhanced gas hydrate formation

Novel Vermiculite/tannic Acid Composite Aerogels with Outstanding CO2 Storage Via Enhanced Gas Hydrate Formation

Carbon Material-Based Aerogels for Gas Adsorption: Fabrication, Structure Design, Functional Tailoring, and Applications

Hydrate-based adsorption-hydration hybrid approach enhances methane storage in wet MIL-101(Cr)@AC under mild condition

Efficient CO2 Capture by ZIF-8-derived In-Situ Nitrogen-Doped Nanoporous Carbon with Ultra-High Selectivity and Stability

Experimental study on synergistic promotion of reciprocating impact and porous materials on methane capture based on hydrate method

Microporous MOF-5@AC and Cu-BDC@AC Composite Materials for Methane Storage in ANG Technology

Changes and challenges in sustainability of technical and vocational education and training — teacher education programme: A case study

Methane Storage and Purification of Natural Gas in Metal‐Organic Frameworks

Microporous Carbon Adsorbents Prepared by Activating Reagent-Free Pyrolysis for Upgrading Low-Quality Natural Gas

Porous MOFs with geometric mismatch between trimers and octatopic pyrene-based ligands for low-temperature methane storage