PELVIC LYMPH NODE DISSECTION FOLLOWING RADIOTHERAPY FOR CANCER OF THE CERVIX: RE-EVALUATION.

M. Gray,H. C. Frick

DOI: https://doi.org/10.1016/0002-9378(65)90302-9

IF: 9.8

1965-09-01

American Journal of Obstetrics and Gynecology

Abstract:

What problem does this paper attempt to address?

TDOA-TWR based positioning algorithm for UWB localization system

Marcin Kolakowski,Vitomir Djaja-Josko

DOI: https://doi.org/10.1109/MIKON.2016.7491981

2024-02-15

Abstract:Ultra-wideband positioning systems intended for indoor applications often work in non-line of sight conditions, which result in insufficient precision and accuracy of derived localizations. One of the possible solutions is the implementation of cooperative positioning techniques. The following paper describes a cooperative ultra-wideband positioning system which calculates tag position from TDOA and distance between tags measurements. In the paper positioning system architecture is described and an exemplary transmission scheme for cooperative systems is presented. Considered localization system utilizes an Extended Kalman Filter based algorithm. The algorithm was investigated with simulations and experiments. Conducted experiment consisted in fusing results gathered from typical TDOA positioning system infrastructure and ranging results obtained with ultra-wideband radio modules. The research has shown that the use presented cooperative algorithm increases positioning precision.

Signal Processing
Error analysis and experimental study on indoor UWB TDoA localization with reference tag

Tiandong Wang,Xi Chen,Ning Ge,Yukui Pei

DOI: https://doi.org/10.1109/APCC.2013.6766000

2013-01-01

Abstract:In indoor UWB TDoA localization systems, anchor clock drifts, RF and ADCs front end delay and their long term variation are main performance limiting factors. Anchor synchronization using reference tags instead of wired lines are promising for ease of deployment In this work, an error analysis on UWB TDoA localization system with reference tag is performed, focusing on propagation and clock drifts. A 500 MHz experimental UWB localization system with reference tag was built. Using single carrier UWB signal with a 127 chip PN code, the smallest TDoA measurement error is 21.7 cm and the worst error is 45.3 cm, as was shown by the test results.
A CFO-Assisted Algorithm for Wireless Time-Difference-of-Arrival Localization Networks: Analytical Study and Experimental Results

Cédric Hannotier,François Horlin,François Quitin

DOI: https://doi.org/10.3390/s24030737

IF: 3.9

2024-01-24

Sensors

Abstract:Localization of wireless transmitters is traditionally done using Radio Frequency (RF) sensors that measure the propagation delays between the transmitter and a set of anchor receivers. One of the major challenges of wireless localization systems is the need for anchor nodes to be time-synchronized to achieve accurate localization of a target node. Using a reference transmitter is an efficient way to synchronize the anchor nodes Over-The-Air (OTA), but such algorithms require multiple periodic messages to achieve tight synchronization. In this paper, we propose a new synchronization method that only requires a single message from a reference transmitter. The main idea is to use the Carrier Frequency Offset (CFO) from the reference node, alongside the Time of Arrival (ToA) of the reference node messages, to achieve tight synchronization. The ToA allows the anchor nodes to compensate for their absolute time offset, and the CFO allows the anchor nodes to compensate for their local oscillator drift. Additionally, using the CFO of the messages sent by the reference nodes and the target nodes also allow us to estimate the speed of the targets. The error of the proposed algorithm is derived analytically and is validated through controlled laboratory experiments. Finally, the algorithm is validated by realistic outdoor vehicular measurements with a software-defined radio testbed.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Design and Implementation of Real-Time Localization System (RTLS) Based on UWB and TDoA Algorithm

Fengyun Zhang,Li Yang,Yuhuan Liu,Yulong Ding,Shuang-Hua Yang,Hao Li

DOI: https://doi.org/10.3390/s22124353

IF: 3.9

2022-06-08

Sensors

Abstract:Nowadays, accurate localization plays an essential role in many fields, such as target tracking and path planning. The challenges of indoor localization include inadequate localization accuracy, unreasonable anchor deployment in complex scenarios, lack of stability, and the high cost. So, the universal positioning technologies cannot meet the real application requirements scarcely. To overcome these shortcomings, a comprehensive ultra wide-band (UWB)-based real-time localization system (RTLS) is presented in this paper. We introduce the architecture of a real-time localization system, then propose a new wireless clock synchronization (WCS) scheme, and finally discuss the time difference of arrival (TDoA) algorithm. We define the time-base selection strategy for the TDoA algorithm, and we analyze the relationship between anchor deployment and positioning accuracy. The extended Kalman filter (EKF) method is presented for non-linear dynamic localization estimation, and it performs well in terms of stability and accuracy on moving targets.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Ultra-Precise Synchronization for TDoA-based Localization Using Signals of Opportunity

Thomas Maul,Sebastian Klob,Joerg Robert

2023-06-08

Abstract:Precise localization is one key element of the Internet of Things (IoT). Especially concepts for position estimation when Global Navigation Satellite Systems (GNSS) are unavailable have moved into the focus. One crucial component for localization systems in general and precise runtime-based positioning, in particular, is the necessity of ultra-precise clock synchronization between the receiving base stations. Our work presents a software-based approach for the wireless synchronization of spatially separated base stations using a low-cost off-the-shelf frontend architecture. The proposed system estimates the time synchronization, sampling clock offset, and carrier frequency offset using broadcast signals as Signals of Opportunity. In this paper, we derive the theoretical lower bound for the estimation variance according to the Modified Cramer-Rao Bound. We show that a theoretical time synchronization accuracy in the range of ps and a frequency synchronization precision in the range of milli-Hertz is achievable. An algorithm is presented that estimates the desired parameter based on evaluating the Cross-Correlation Function between base stations. Initial measurements are conducted in a real-world environment. It is shown that the presented estimator nearly reaches the theoretical bound within a time and frequency synchronization accuracy of down to 200 ps and 6 mHz, respectively.

Distributed, Parallel, and Cluster Computing,Signal Processing
Bilateral control for haptic laparoscopic surgery robot

S. Yoon,Won Jae Kim,Min-Cheol Lee,Woo-Hyeok Choi

DOI: https://doi.org/10.1109/ISR.2013.6695660

2013-10-01

Abstract:When using commercialized robot assisted laparoscopic such as Da Vinci, surgeon has met some problem to depend only on the information by visual feedback. To solve this problem, haptic function is required. In order to realize the haptic teleoperation system, force feedback and bilateral control system are needed. The previous researches showed that the perturbation value estimated by sliding perturbation observer(SPO) followed a reaction force loaded on the surgical robot instrument well. This paper addresses a bilateral control which is performed to realize haptic teleoperation based on this estimated force. The experiment results shows that a torque and force sensorless teleoperation system can be implemented using bilateral control structure.
Indoor Positioning Using Ultrawideband and Inertial Measurements

Manon Kok,Jeroen D. Hol,Thomas B. Schön,Thomas B. Schon

DOI: https://doi.org/10.1109/tvt.2015.2396640

IF: 6.8

2015-04-01

IEEE Transactions on Vehicular Technology

Abstract:In this paper, we present an approach to combine measurements from inertial sensors (accelerometers and gyroscopes) with time-of-arrival measurements from an ultrawideband (UWB) system for indoor positioning. Our algorithm uses a tightly coupled sensor fusion approach, where we formulate the problem as a maximum a posteriori (MAP) problem that is solved using an optimization approach. It is shown to lead to accurate 6-D position and orientation estimates when compared to reference data from an independent optical tracking system. To be able to obtain position information from the UWB measurements, it is imperative that accurate estimates of the UWB receivers' positions and their clock offsets are available. Hence, we also present an easy-to-use algorithm to calibrate the UWB system using a maximum-likelihood (ML) formulation. Throughout this work, the UWB measurements are modeled by a tailored heavy-tailed asymmetric distribution to account for measurement outliers. The heavy-tailed asymmetric distribution works well on experimental data, as shown by analyzing the position estimates obtained using the UWB measurements via a novel multilateration approach.

telecommunications,engineering, electrical & electronic,transportation science & technology
Ultraviolet Positioning via TDOA: Error Analysis and System Prototype

Shihui Yu,Chubing Lv,Yueke Yang,Yuchen Pan,Lei Sun,Juliang Cao,Ruihang Yu,Chen Gong,Wenqi Wu,Zhengyuan Xu

2024-04-15

Abstract:This work performs the design, real-time hardware realization, and experimental evaluation of a positioning system by ultra-violet (UV) communication under photon-level signal detection. The positioning is based on time-difference of arrival (TDOA) principle. Time division-based transmission of synchronization sequence from three transmitters with known positions is applied. We investigate the positioning error via decomposing it into two parts, the transmitter-side timing error and the receiver-side synchronization error. The theoretical average error matches well with the simulation results, which indicates that theoretical fitting can provide reliable guidance and prediction for hardware experiments. We also conduct real-time hardware realization of the TDOA-based positioning system using Field Programmable Gate Array (FPGA), which is experimentally evaluated via outdoor experiments. Experimental results match well with the theoretical and simulation results.

Systems and Control
Angle of Arrival and Centimeter Distance Estimation on a Smart UWB Sensor Node

Tobias Margiani,Silvano Cortesi,Milena Keller,Christian Vogt,Tommaso Polonelli,Michele Magno

DOI: https://doi.org/10.1109/TIM.2023.3282289

2023-12-21

Abstract:Accurate and low-power indoor localization is becoming more and more of a necessity to empower novel consumer and industrial applications. In this field, the most promising technology is based on UWB modulation; however, current UWB positioning systems do not reach centimeter accuracy in general deployments due to multipath and nonisotropic antennas, still necessitating several fixed anchors to estimate an object's position in space. This article presents an in-depth study and assessment of angle of arrival (AoA) UWB measurements using a compact, low-power solution integrating a novel commercial module with phase difference of arrival (PDoA) estimation as integrated feature. Results demonstrate the possibility of reaching centimeter distance precision and ang 2.4 average angular accuracy in many operative conditions, e.g., in a ang 90 range around the center. Moreover, integrating the channel impulse response, the phase differential of arrival, and the point-to-point distance, an error correction model is discussed to compensate for reflections, multipaths, and front-back ambiguity.

Signal Processing
Range-Extension Algorithms and Strategies for TDOA Ultra-Wideband Positioning System

Shih-Ping Huang,Chien-Bang Chen,Tan-Zhi Wei,Wei-Ting Tsai,Chong-Yi Liou,Yuan-Mou Mao,Wang-Huei Sheng,Shau-Gang Mao

DOI: https://doi.org/10.3390/s23063088

2023-03-13

Abstract:The Internet of Things (IoT) for smart industry requires the surveillance and management of people and objects. The ultra-wideband positioning system is an attractive solution for achieving centimeter-level accuracy in target location. While many studies have focused on improving the accuracy of the anchor coverage range, it is important to note that in practical applications, positioning areas are often limited and obstructed by furniture, shelves, pillars, or walls, which can restrict the placement of anchors. Furthermore, some positioning regions are located beyond anchor coverage, and a single group with few anchors may not be able to cover all rooms and aisles on a floor due to non-line-of-sight errors causing severe positioning errors. In this work, we propose a dynamic-reference anchor time difference of arrival (TDOA) compensation algorithm to enhance accuracy beyond anchor coverage by eliminating local minima of the TDOA loss function near anchors. We designed a multidimensional and multigroup TDOA positioning system with the aim of broadening the coverage of indoor positioning and accommodating complex indoor environments. By employing an address-filter technique and group-switching process, tags can seamlessly move between groups with a high positioning rate, low latency, and high accuracy. We deployed the system in a medical center to locate and manage researchers with infectious medical waste, demonstrating its usefulness for practical healthcare institutions. Our proposed positioning system can thus facilitate precise and wide-range indoor and outdoor wireless localization.
A KFL-TOA UWB indoor positioning method for complex environment

Linhui Zhao,Yaping Dai,Guosai Yang,Yijun Xu

DOI: https://doi.org/10.1109/CAC.2017.8243291

2017-10-01

Abstract:For the positioning in a complex indoor environment, this paper proposed an indoor positioning method used Ultra-Wide Band (UWB), which based on time of arrival (TOA) principle, combining Kalman filtering and linearized (KFL-TOA). This method can reduce the positioning error and improve positioning accuracy effectively when the UWB signal is interfered by the multipath effect or the non-line-of-sight (NLOS). The DWM1000 module is used in the positioning system. Compared with traditional TOA positioning method, the positioning result show that: in the non-interference condition, The KFL-UWB can reduce 31.7% of the Root Mean Square Error (RMSE) and 31.0% of the Circular Error Probable (CEP); In the multipath effect condition, it can reduce 13.7% of the RMSE and 9.7% of the CEP; In the NLOS condition, it can reduce 32.9% of the RMSE and 36.1% of the CEP.

Computer Science,Engineering
Analysis of the Scalability of UWB Indoor Localization Solutions for High User Densities

Matteo Ridolfi,Samuel Van de Velde,Heidi Steendam,Eli De Poorter

DOI: https://doi.org/10.3390/s18061875

IF: 3.9

2018-06-07

Sensors

Abstract:Radio frequency (RF) technologies are often used to track assets in indoor environments. Among others, ultra-wideband (UWB) has constantly gained interest thanks to its capability to obtain typical errors of 30 cm or lower, making it more accurate than other wireless technologies such as WiFi, which normally can predict the location with several meters accuracy. However, mainly due to technical requirements that are part of the standard, conventional medium access strategies such as clear channel assessment, are not straightforward to implement. Since most scientific papers focus on UWB accuracy improvements of a single user, it is not clear to which extend this limitation and other design choices impact the scalability of UWB indoor positioning systems. We investigated the scalability of indoor localization solutions, to prove that UWB can be used when hundreds of tags are active in the same system. This paper provides mathematical models that calculate the theoretical supported user density for multiple localization approaches, namely Time Difference of Arrival (TDoA) and Two-Way Ranging (TWR) with different MAC protocol combinations, i.e., ALOHA and TDMA. Moreover, this paper applies these formulas to a number of realistic UWB configurations to study the impact of different UWB schemes and settings. When applied to the 802.15.4a compliant Decawave DW1000 chip, the scalability dramatically degrades if the system operates with uncoordinated protocols and two-way communication schemes. In the best case scenario, UWB DW1000 chips can actively support up to 6171 tags in a single domain cell (no handover) with well-selected settings and choices, i.e., when adopting the combination of TDoA (one-way link) and TDMA. As a consequence, UWB can be used to simultaneously localize thousands of nodes in a dense network. However, we also show that the number of supported devices varies greatly depending on the MAC and PHY configuration choices.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Finding the Right Place: Sensor Placement for UWB Time Difference of Arrival Localization in Cluttered Indoor Environments

Wenda Zhao,Abhishek Goudar,Angela P. Schoellig

DOI: https://doi.org/10.1109/lra.2022.3165181

IF: 5.2

2022-07-01

IEEE Robotics and Automation Letters

Abstract:Ultra-wideband (UWB) time difference of arrival (TDOA)-based localization has recently emerged as a promising indoor positioning solution. However, in cluttered environments, both the UWB radio positions and the obstacle-induced non-line-of-sight (NLOS) measurement biases significantly impact the quality of the position estimate. Consequently, the placement of the UWB radios must be carefully designed to provide satisfactory localization accuracy for a region of interest. In this work, we propose a novel algorithm that optimizes the UWB radio positions for a pre-defined region of interest in the presence of obstacles. The mean-squared error (MSE) metric is used to formulate an optimization problem that balances the influence of the geometry of the radio positions and the NLOS effects. We further apply the proposed algorithm to compute a minimal number of UWB radios required for a desired localization accuracy and their corresponding positions. In a real-world cluttered environment, we show that the designed UWB radio placements provide 47 and 76 localization root-mean-squared error (RMSE) reduction in 2D and 3D experiments, respectively, when compared against trivial placements.

robotics
High-Accuracy TDOA-Based Localization Without Time Synchronization

Bin Xu,Guodong Sun,Ran Yu,Zheng Yang

DOI: https://doi.org/10.1109/tpds.2012.248

IF: 5.3

2013-01-01

IEEE Transactions on Parallel and Distributed Systems

Abstract:Localization is of great importance in mobile and wireless network applications. Time Difference of Arrival (TDOA) is one of the widely used localization schemes, in which the target (source) emits a signal and a number of anchors (receivers) record the arriving time of the source signal. By calculating the time difference of different receivers, the location of the target is estimated. In such a scheme, receivers must be precisely time synchronized. But time synchronization adds computational cost, and brings errors which may lower localization accuracy. Previous studies have shown that existing time synchronization approaches using low-cost devices are insufficiently accurate, or even infeasible under high requirement for accuracy. In our scheme (called Whistle), several asynchronous receivers record a target signal and a successive signal that is generated artificially. By two-signal sensing and sample counting techniques, time synchronization requirement can be removed, while high time resolution can be achieved. This design fundamentally changes TDOA in the sense of releasing the synchronization requirement and avoiding many sources of errors caused by time synchronization. We implement Whistle on commercial off-the-shelf (COTS) cell phones with acoustic signal and perform simulations with UWB signal. Especially we use Whistle to localize nodes of large-scale wireless networks, and also achieve desirable results. The extensive real-world experiments and simulations show that Whistle can be widely used with good accuracy.
A Software Defined Radio Platform for Passive UWB-RFID Localization

Chuanying Zhai,Zhuo Zou,Qin Zhou,Lirong Zheng

DOI: https://doi.org/10.1109/icwits.2012.6417741

2012-01-01

Abstract:In this work, we further demonstrate the passive UWB-RFID positioning system by using a Software Defined Radio (SDR) platform. The SDR platform works as the UWB reader network to perform the ToA estimations and the time-difference-of-arrival (TDoA) positioning calculation. It is implemented by an oscilloscope and a set of off-shelf components. The oscilloscope features high-speed real-time sampling (40 GS/s), with 4 independent synchronized channels, enabling the multi-antenna multi-channel receiver realization in UWB bands with signal processing capability. The algorithms are evaluated and the system concept is demonstrated. According to the experimental results, the SDR platform using 4 receiver nodes successfully realizes the real-time positioning and achieves an average positioning with a best accuracy of 4 cm root-mean-square-error (RMSE) in 1m×1m area.
Time-based UWB localization architectures analysis for UAVs positioning in industry

Javier Díez-González,Rubén Ferrero-Guillén,Paula Verde,Alberto Martínez-Gutiérrez,Rubén Álvarez,Joaquín Torres-Sospedra

DOI: https://doi.org/10.1016/j.adhoc.2024.103419

IF: 4.816

2024-04-01

Ad Hoc Networks

Abstract:Ultra-Wide-Band (UWB) technology allows for partially mitigating the NLOS and multipath effects of time-based localization in low-range applications. Thus, it has been widely proposed for indoor navigation, reaching very promising results with mature technology already available. However, an analysis of the suitability of different synchronous and asynchronous time-based architectures can provide valid conclusions for the future development of this field. For this reason, we perform in this paper a fair comparison of two traditional synchronous architectures (TOA and TDOA) and one asynchronous architecture (A-TDOA) defining the lowest error bounds for each architecture in an indoor industrial scenario devised for UAV navigation. Results have shown that although current industrial time-based localization software is mainly based on TDOA (synchronous) and Two-Way-Range (asynchronous) architectures, asynchronous localization can statistically provide more accurate and stable positioning services in indoor industrial environments. These results encourage further experimentation in other different asynchronous architectures in the coming years.

computer science, information systems,telecommunications
A Real-Time UWB Location and Tracking System Based on TWR-TDOA Estimation and a Simplified MPGA Layout Optimization

Yanping Zhu,Lei Huang,Jing Liu,Zhongkang Cao,Jinli Chen,Zijian Mu

DOI: https://doi.org/10.1155/2022/1194169

2022-08-02

Mobile Information Systems

Abstract:This article designs and implements a 3D moving target positioning and tracking system by using ultrawideband (UWB) technology. The result of the two-way ranging by the time difference of arrival (TWR-TDOA) positioning algorithm is adopted to result in a new resolution that is to resolve the hyperbolic equations. The proposed algorithm is applied to outdoor and indoor scenarios. To minimize the effect of the sensor layout, this article proposes a simplified multi-population genetic algorithm (MPGA) to obtain the optimum distribution of anchors, which can rapidly reduce the number of search iterations. To resolve the low stability of the TDOA algorithm in outdoor and indoor scenarios, the Kalman filter algorithm is utilized to improve the stability and positioning accuracy of this system and a good simulation effect is achieved. The test results show that the system's positioning error is far less than that of using other methods. The whole system has a feature of high precision, high stability, low complexity, and low cost.

computer science, information systems,telecommunications
Data-Driven Antenna Delay Calibration for UWB Devices for Network Positioning

Zuoya Liu,Teemu Hakala,Juha Hyyppä,Antero Kukko,Harri Kaartinen,Ruizhi Chen

DOI: https://doi.org/10.1109/tim.2023.3348891

IF: 5.6

2024-02-02

IEEE Transactions on Instrumentation and Measurement

Abstract:This study presents a real-time and fully automatic antenna delay calibration approach for ultrawideband (UWB) devices, which can be utilized to evaluate the combined delay of each UWB device used in the positioning system. Two estimators, a coarse estimator and a fine-tuning estimator, operate closely together in the calibration. The coarse estimator can determine a common coarse value for all devices involved in the calibration; the fine-tuning estimator continuously determines the optimal value for each device. More than three UWB devices can be calibrated simultaneously in real-time in the developed approach, making it a suitable solution for positioning applications with a large number of UWB devices. To evaluate the calibration accuracy of the proposed approach and verify the ranging accuracy and precision at different distances, experiments were conducted in an indoor office space and outdoors in an open space using universal UWB devices (DWM1001 from Decawave). The experimental results show that the proposed approach achieves a ranging precision of better than ±0.01 m within a base UWB network for each pair of devices and achieves a ranging accuracy and precision of better than ±0.05 m in a distance range from 1 to 25 m after calibration and bias correction for a remote/moving UWB device. Therefore, the developed approach is sufficient for UWB-based applications in which each UWB device must remain in a stationary state at the horizontal plane spanned by the devices in space to ensure the performance of the positioning system.

engineering, electrical & electronic,instruments & instrumentation
Utilizing acceleration measurements to improve TDOA based localization

Marcin Kolakowski

DOI: https://doi.org/10.1109/SPS.2017.8053694

2024-03-29

Abstract:In this paper localization using UWB positioning system and an inertial unit containing a single accelerometer is considered. The main part of the paper describes a novel algorithm for person localization. The algorithm is based on modified Extended Kalman Filter and utilizes TDOA (Time Difference of Arrival) results obtained from UWB system and results of acceleration measurement performed by the localized tag device. The proposed algorithm has been experimentally investigated through simulation and experiments. The results are included in the paper.

Signal Processing
High-Precision Joint TDOA and FDOA Location System

Guoyao Xiao,Qianhui Dong,Guisheng Liao,Shuai Li,Kaijie Xu,Yinghui Quan

DOI: https://doi.org/10.3390/rs16040693

IF: 5

2024-02-16

Remote Sensing

Abstract:Passive location based on TDOA (time difference of arrival) and FDOA (frequency difference of arrival) is the mainstream method for target localization. This paper proposes a fast time–frequency difference positioning method to address issues such as low accuracy, large computational resource utilization, and limited suitability for real-time signal processing in the conventional CAF (cross-ambiguity function)-based approach, aiming to complete the processing of the target radiation source to obtain the target parameters within a short timeframe. In the mixing product operation step of the CAF, a frequency-domain approach replaces the time-domain convolution operation in PW-ZFFT (pre-weighted Zoom-FFT) to reduce the computational load of the CAF. Additionally, a quadratic surface fitting method is used to enhance the accuracy of TDOA and FDOA. The localization solution is obtained using Newton's method, which can provide more accurate results compared to analytical methods. Next, a signal processing platform is designed with FPGA (field-programmable gate array) and multi-core DSP (digital signal processor), and works by dividing and mapping the algorithm functional modules according to the hardware's characteristics. We analyze the architectural advantages of multi-core DSP and design methods to improve program performance, such as EDMA transfer optimization, inline function optimization, and cache optimization. Finally, this paper constructs simulation tests in typical positioning scenarios and compares them to hardware measurement results, thus confirming the correctness and real-time capability of the program.

environmental sciences,imaging science & photographic technology,remote sensing,geosciences, multidisciplinary

PELVIC LYMPH NODE DISSECTION FOLLOWING RADIOTHERAPY FOR CANCER OF THE CERVIX: RE-EVALUATION.

TDOA-TWR based positioning algorithm for UWB localization system

Error analysis and experimental study on indoor UWB TDoA localization with reference tag

A CFO-Assisted Algorithm for Wireless Time-Difference-of-Arrival Localization Networks: Analytical Study and Experimental Results

Design and Implementation of Real-Time Localization System (RTLS) Based on UWB and TDoA Algorithm

Ultra-Precise Synchronization for TDoA-based Localization Using Signals of Opportunity

Bilateral control for haptic laparoscopic surgery robot

Indoor Positioning Using Ultrawideband and Inertial Measurements

Ultraviolet Positioning via TDOA: Error Analysis and System Prototype

Angle of Arrival and Centimeter Distance Estimation on a Smart UWB Sensor Node

Range-Extension Algorithms and Strategies for TDOA Ultra-Wideband Positioning System

A KFL-TOA UWB indoor positioning method for complex environment

Analysis of the Scalability of UWB Indoor Localization Solutions for High User Densities

Finding the Right Place: Sensor Placement for UWB Time Difference of Arrival Localization in Cluttered Indoor Environments

High-Accuracy TDOA-Based Localization Without Time Synchronization

A Software Defined Radio Platform for Passive UWB-RFID Localization

Time-based UWB localization architectures analysis for UAVs positioning in industry

A Real-Time UWB Location and Tracking System Based on TWR-TDOA Estimation and a Simplified MPGA Layout Optimization

Data-Driven Antenna Delay Calibration for UWB Devices for Network Positioning

Utilizing acceleration measurements to improve TDOA based localization

High-Precision Joint TDOA and FDOA Location System