Basaloid squamous cell carcinoma versus basal cell adenocarcinoma of the oral cavity.

D. Andreadis,A. Nomikos,A. Epivatianos,A. Poulopoulos,C. Barbatis

DOI: https://doi.org/10.1080/00313020500368048

2005-12-01

Abstract:

What problem does this paper attempt to address?

A study of the self-coupling magnetic resonance coupled wireless power transfer

Liqing Tong,Hulong Zeng,Fangzheng Peng

DOI: https://doi.org/10.1109/APEC.2015.7104800

2015-01-01

Abstract:It is shown that the efficiency and usable frequency for the industrial, scientific, and medical (ISM) is significant in magnetic resonance coupled (MRC) wireless power transfer (WPT). A self-coupling MRC WPT system is proposed in this paper. It combines the source coil and transmitting coil or receiving coil and load coil as a self-coupling coil. There mainly are three kind power transfer ways, conductive coupling, inductive coupling and magnetic resonance coupling where, the conductive coupling being the self-coupling coil's inertial will not affect the magnetic resonance coupling works like as traditional four coils configuration. The mutual inductance equivalent circuit model is constructed also. Through the equivalent circuit model and experimental measure, the proposed WPT can achieve higher efficiency.
Design and Optimization of a Wireless Power Transfer System with a High Voltage Transfer Ratio

Jing Zhou,Jiacheng Wang,Pengzhi Yao,Yanliang Lu,Aixi Yang,Jian Gao,Sideng Hu

DOI: https://doi.org/10.3390/electronics11142115

IF: 2.9

2022-01-01

Electronics

Abstract:With the development of the logistics industry, low-voltage systems, such as intelligent logistics vehicles, have also started to propose application scenarios for wireless power transfer systems. As most logistics vehicles use lithium batteries for energy supply, the wireless charging system has to adapt to the charging characteristic curve of lithium batteries. In this paper, a dual-transmitter single-receiver compound resonant compensation topology with a high voltage ratio is proposed, and a corresponding magnetic coupler is designed and optimized through finite element analysis, which guarantees adaptive output curves according to the working state. A 1 kW experimental platform is established to verify the theoretical analysis, which realizes a high voltage transformation ratio with 90.3% efficiency. Throughout the whole charging process, the output curve agrees with the charging profile of the lithium battery, which can greatly extend the service life of lithium batteries.
Wireless energy transfer system based on metglas/PFC magnetoelectric laminated composites

Yu Xin-Jie,Wu Tian-Yi,Li Zhen

DOI: https://doi.org/10.7498/aps.62.058503

IF: 0.906

2013-01-01

Acta Physica Sinica

Abstract:Wireless energy transfer has broad prospective applications.Current researches focus on electromagnetic induction and magnetic resonance.The former approach is sensitive to position and the latter has larger size,both of which affect the broad application of wireless energy transfer.Two layers of magnetostrictive effect materials and one layer of piezoelectric effect material are bound by epoxy resin,which generates magnetoelectric laminated composite.It is the first time that the output voltage,current and magnetoelectric factor have been deduced without DC magnetic bias.Three samples are implemented and the wireless energy transfer system based on them is developed.The tests on the samples verify the correctness of the theoretic analysis.Further experiments illustrate that there are double frequency characteristics for the magnetoelectric laminated composites;the resonant frequency is proportional to the reciprocal of the length of the composite;the open circuit voltage of the composite could reach 100 V(rms) under a magnetic field of 20 Oe;the maximum energy transferred is 520 mW,which is the highest record reported up to now,with the energy density 1.21W/cm 3 and maximum transfer efficiency 35%;the rotation less than 30° has little effect on the output of the composites.Theoretical analyses and experimental results suggest that the magnetoelectric laminated composite based on Metglas/PFC is a very interesting approach to small volume and small power wireless energy transfer applications.
High efficiency class-E RF power amplifier for wireless power transfer system

Jiang-long CHU,Yu-ling LI,Shi-you YANG

DOI: https://doi.org/10.3969/j.issn.1003-3076.2014.04.001

2014-01-01

Abstract:Power amplifier as the power source of wireless power transfer system is a critical part in this system, al?so called witricity. To improve the efficiency of the whole system and adapt to different coil structure, a high effi?ciency class?E power amplifier is developed. To determine the S?parameters in modelling board layout for electro?magnetic analysis, the method of moments ( MOM) is employed. Also the electromagnetic compatibility issues in designing are carefully considered. This paper provides the design steps and simulation results. The practical am?plifier can provides a peak Power?Added?Efficiency of 93% with a power gain of 19?9 dB at an output power of 43?9 dBm. A power gain of 19 dB and PAE of 89% can be achieved for different coil structure. A PAE more than 60% can be got for different internal resistance or coil distance coil structure. Those experimental results confirm positively the feasibility of the proposed work.
Performance Analysis and Experimental Verification of Mid-Range Wireless Energy Transfer Through Non-Resonant Magnetic Coupling

L. Peng,J. Y. Wang,L. X. Ran,O. Breinbjerg,N. A. Mortensen

DOI: https://doi.org/10.1163/156939311794827186

2011-01-01

Journal of Electromagnetic Waves and Applications

Abstract:In this paper, the efficiency analysis of a mid-range wireless energy transfer system is performed through non-resonant magnetic coupling. It is shown that the self-resistance of the coils and the mutual inductance are critical in achieving a high efficiency, which is indicated by our theoretical formulation and verified in our experiments. It is experimentally shown that high efficiency, up to 65%, can be realized even in a non-resonant wireless energy system which employs a device part with moderate or low quality factor. We also address some aspects of a practical wireless energy transfer system and show that careful design of the de-tuned system can intrinsically minimize the power dissipated in the source part. Our non-resonant scheme presented in this paper allows flexible design and fabrication of a wireless energy transfer systems with transfer distance being several times of the coils' radius.
Great Enhancement of Energy Harvesting Properties of Piezoelectric/Magnet Composites by the Employment of Magnetic Concentrator

Jinchi Han,Jun Hu,Shan X. Wang,Jinliang He

DOI: https://doi.org/10.1063/1.4906964

IF: 2.877

2015-01-01

Journal of Applied Physics

Abstract:Wireless sensors capable of scavenging energy from ambient environment have been increasingly attractive for their outstanding merits of self-sufficient and maintenance-free. This paper presents a specific design of magnetic energy harvester based on a piezoelectric/magnet composite and a magnetic concentrator. With the employment of concentrator, the energy harvesting properties have been greatly improved, which is theoretically analyzed and experimentally demonstrated with the 35 times power enlargement. The fabricated prototype with a 3 cm air-gap concentrator harvests 326 μW power at 10 Arms, which enables sufficient and reliable power supply for a wide range of low-power sensors.
Magnetic Pendulum Arrays for Efficient Wireless Power Transmission

S P Mysore Nagaraja,R U Tok,R Zhu,S Bland,A Propst,Y E Wang

DOI: https://doi.org/10.1088/1742-6596/1407/1/012049

2019-11-01

Journal of Physics: Conference Series

Abstract:Abstract In this paper we would like to propose an innovative electromechanical transmitter called Magnetic Pendulum Array (MPA), for efficient wireless power transmission at Ultra Low Frequencies (ULF). We take advantage of the high Quality (Q) factor and low dissipation in the electromechanical system to demonstrate efficient power transfer. It has been shown that using Magnetic Pendulum arrays leads to about 10dB% higher power transfer efficiency at the resonance frequency of 447 Hz as compared to a coil of similar dimensions.
Wireless Power and Information Dual Transfer System Via Magnetically Coupled Resonators

Xiangning He,Sheng Liu,Jiande Wu,Yue Feng,Ruichi Wang,Wuhua Li,Wanying Weng

DOI: https://doi.org/10.1038/s44172-023-00154-4

2024-01-01

Communications Engineering

Abstract:Abstract High-efficiency medium-range wireless power transfer using magnetically coupled resonators requires a wireless data link between the contactless coils to regulate power. Multiplexing the power transfer channel as the information channel is a cost-effective solution for the communication. However, existing technologies cannot transmit data across the medium-range magnetically coupled resonators channel without substantially affecting power transfer. Here we show a power-electronics-converters based wireless power and information dual transfer system in which the information signals are modulated on one dc side of the inverter/rectifier, and transmitted through a conventional medium-range wireless power transfer system, and then demodulated on the other dc side. Using the frequency mixer characteristic of the inverter/rectifier, information is modulated onto the sideband of the power carrier and transmitted through the medium-range channel. Finally, we prototyped a 6.78 MHz system capable of transferring 45 W power across a one-meter distance with 62% efficiency and 60 kb/s bitrate for half-duplex communication.
Magnetic Energy Coupling System Based on Micro-Electro-Mechanical System Coils

Xiuhan Li,Quan Yuan,Tianyang Yang,Jian Liu,Haixia Zhang

DOI: https://doi.org/10.1063/1.3680528

IF: 2.877

2012-01-01

Journal of Applied Physics

Abstract:In this paper, a high efficiency wireless energy transfer system based on MEMS coils is first developed. The permanent magnetic core used in the transmitting coil can not only enhance the magnetic flux but also applies a strong and uniform magnetic field distribution around the core. Ansoft hfss is then used to analyze the performance of two coupling coils designed to be resonated at the same frequency. The distribution of magnetic field strength and coupling efficiency is modeled and characterized. High-performance bio-compatible MEMS coils were fabricated on a glass wafer by thick glue photolithography and electroplating technique. We measured a peak value of energy transfer at the resonant frequency of 23 MHz, and the coupling efficiency is higher than 10% within the distance of 10–20 cm by sweeping frequencies from 1 MHz to 200 MHz. Experiments also show that the resonant coupling efficiency is not much affected by the relative position of the two coils in a large range.
An Optimal Design Method for Improving the Efficiency of Ultrasonic Wireless Power Transmission during Communication

Yu Li,Juan Cui,Gang Li,Lu Liu,Yongqiu Zheng,Junbin Zang,Chenyang Xue

DOI: https://doi.org/10.3390/s22030727

IF: 3.9

2022-01-18

Sensors

Abstract:Due to the excellent directivity, strong penetrability, and no electromagnetic shielding effect, ultrasonic waves have good potential for wireless energy transmission and information transfer inside and outside of sealed metal devices. However, traditional ultrasonic based energy transmission methods usually result in considerable energy consumption because of the impedance mismatch during the impedance modulation of the communication. This paper presents an optimal design method for efficient energy transfer during ultrasonic communication. The channel equivalent circuit model is established by only using the acoustic-electric channel scattering parameters. According to the equivalent circuit model, the channel impedance matches with a weak mismatch state is performed during the communication. In this way, the impedance modulation effect is ensured with a lower decrease in the energy transmission efficiency. Finally, the simultaneous energy transmission and impedance modulation are carried out through the 11 mm thick 304 stainless steel plate. The transmission power is 37.86 W with a transmission efficiency of 45.75%, and the modulation rate is 10 Kbps. Compared with the traditional methods, our proposed energy transmission efficiency is increased by 17.62%. The results verify the proposed method’s effectiveness and the high accuracy of the model. The proposed method has great engineering applications and broad prospects in condition monitoring of metallic environments.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
A Mechanical Antenna for Long-Wave Communication by Integrating Piezoelectric Material and Magnets

Jishuo Wang,Chaoyang Zhao,Miao Zhang,Xiaobo Liao,Yaowen Yang,Weifeng Yuan

DOI: https://doi.org/10.1088/1402-4896/ad4fc7

2024-05-24

Physica Scripta

Abstract:The Chu's limit imposes a significant challenge for traditional antennas operating at extremely low frequencies, as they require a large size due to the long operating wavelength, thus limiting their applicability. To reduce the antenna size, this paper proposes a vibrating beam system for long-wave communication that leverages the inverse piezoelectric effect, vibration theory, and Maxwell's equations. A prototype utilizing beam structures is developed and examined experimentally. Furthermore, the frequency modulation of the vibrating beam system and signal transfer protocol are investigated in detail. The experimental results demonstrate that exciting different vibration modes of the vibrating beam system leads to varied electromagnetic signals in specific rules, enabling long-wave communications and ensuring confidentiality. This work offers valuable insights into the potential of local information exchange among close-range platforms. It also highlights the promising approach of integrating piezoelectric material and magnets within the vibrating beam system, showcasing their potential towards practical applications in long-wave communication.

physics, multidisciplinary
Enhanced SLF radiation efficiency in a piezoelectrically driven magnetic pendulum transmitter

Zhaoqiang Chu,Chenyuan Yu,Wei Dan,Shizhan Jiang,Yuzhu Ren,Kewen Dong,Shuxiang Dong

DOI: https://doi.org/10.1063/5.0193249

IF: 4

2024-02-12

Applied Physics Letters

Abstract:Long-wave radio station based on an electrically small antenna and mechanical transmitter based on a rotating permanent antenna are commonly used for super low frequency (SLF, 30–300 Hz) communication. The current challenge is the difficulty in developing both an efficient and a miniaturized SLF transmitter. Enlightened by the advantages of piezoelectric motor over conventional electromagnetic motor in terms of efficiency and the output torque in low frequency band, we propose a piezoelectrically driven magnetic pendulum transmitter by combining a magneto-mechano-electric (MME) cantilever and a swinging magnet in this work. The magnetic force coupling between the MME cantilever and the swinging magnet is optimized by changing the thickness and the attached position of the used Metglas laminates. The experimental results show that the piezoelectrically driven magnetic pendulum transmitter has a working frequency of 57 Hz, and a flux density of 149 f Tpk at 100 m distance could be expected with a low power consumption of 40.64 mW. When driving the same magnet with an electromagnetic motor, however, the required power consumption reaches 4.2 W for 57 Hz magnetic field radiation. By dividing the induced magnetic moment over the consumed power, the effective radiation efficiency of our proposed piezoelectrically driven SLF magnetic pendulum transmitter significantly increased from 0.55 to 17.4. This proof-of-concept work is believed to open a dimension for the design and the application of efficient SLF mechanical transmitter in the future.

physics, applied
Design and research of hybrid piezoelectric-electromagnetic energy harvester based on magnetic couple suction-repulsion motion and centrifugal action

Jianwen Zhou,Lipeng He,Lei Liu,Gang Yu,Xiangfeng Gu,Guangming Cheng

DOI: https://doi.org/10.1016/j.enconman.2022.115504

IF: 10.4

2022-04-01

Energy Conversion and Management

Abstract:In this paper, a hybrid piezoelectric-electromagnetic energy harvester (HEH) based on magnetic couple suction-repulsion motion and centrifugal action is proposed. Using a control variable approach, the effect of two variables on the output performance was investigated under different parameter conditions in order to maximize the output power. At a mounting angle of 60 degrees for the piezoelectric cantilever beam and a mass of 3.2 g for the rectangular magnet, the entire piezoelectric-electromagnetic harvester can produce 13.32 mW of power, which can successfully power low-power electronic devices such as light-emitting diodes (LEDs). The power generated by mixing piezoelectricity and electromagnetism is 1.16 times greater than the power generated by the piezoelectric generation unit alone and 70.1 times greater than the power generated by the electromagnetic generation unit alone. The composite piezoelectric-electromagnetic hybrid mechanism greatly increases the power output of the entire structure compared to the single generation mode. The suction-repulsion process is accomplished using magnetic coupling. This makes the piezoelectric cantilever beam deformed by the magnetic force and has power output. At the same time, the magnetic suction-repulsion makes the circular magnet complete cutting magnetic induction line motion at the same time, which cleverly combines piezoelectricity and electromagnetism. The form of reciprocating motion of the magnet in the coil frame using suction-repulsion is also proposed for the first time. In addition, compared with those structures that strike the piezoelectric cantilever to generate electricity, this paper uses magnetic coupling, which makes the piezoelectric cantilever beam more durable and longer in use. In summary, this structure has good prospects for application in the direction of powering wireless networks or low-power electronic devices.

energy & fuels,thermodynamics,mechanics
Low-frequency piezoelectric energy harvesting from coupled longitudinal-transverse vibration of two magnetic coupling-based orthogonal beams

Junwu Kan,Chenyang He,Yazhi Lin,Shijie Lin,Zhenxin Cao,Zhonghua Zhang

DOI: https://doi.org/10.1109/jsen.2024.3373021

IF: 4.3

2024-01-01

IEEE Sensors Journal

Abstract:Vibration energy harvesting using piezoelectric transduction is becoming a promising alternative to electrochemical batteries for powering the low-powered wireless and portable electronic devices. Unlike typical cantilevered piezoelectric vibration energy harvesters (PVEHs) where the piezoelectric beam with a tip mass experienced the vibration excitation directly, low-frequency piezoelectric energy harvesting from coupled longitudinal-transverse vibration of two magnetic coupling-based orthogonal beams (LF-PVEH) is proposed in this paper. An attractive feature of the proposed architecture was that the auxiliary beam tolerated the high-shock longitudinal vibration and meanwhile the motion of the auxiliary beam induced the transverse oscillation of piezoelectric beam parallel to the vibration direction via the magnetic coupling. To verify the principle feasibility and ascertain the effect of two magnetically coupled orthogonal beams on the dynamic behaviors and power generation characteristics of the LF-PVEH, theoretical analysis, numerical simulation, and experimental testing were conducted, respectively. The results showed when amplitude increased from 3 to 5 mm, the output maximum voltage increased no more. Besides, by increasing the proof mass m1 to 20 g, the corresponding resonance frequency of the LF-PVEH can be reduced to 8.5 Hz, and when the spatial distance Ly is 10 mm, the optimal effective bandwidth of 8 Hz can be achieved to adapt to the broadband low-frequency vibration environments. The power testing shows that the maximum output power of LF-PVEH can reach 0.2 mW at 11 Hz with the optimal load resistance of 540 kΩ.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
A hybrid piezoelectric-electromagnetic body energy harvester: Design and experiment validation

Hui Guo,Jinyue Wang,Ruihong Dong,Yuanyuan Song,Ran Zhou,Junjie Jin,Fangchao Xu,Feng Sun

DOI: https://doi.org/10.1088/1361-665x/ad8e1f

IF: 4.1

2024-11-04

Smart Materials and Structures

Abstract:The rapid advancement of electronic devices and wireless sensors has heightened the demand for energy sustainability and portable power solutions. This paper proposes a hybrid piezoelectric-electromagnetic energy harvesting (HP-EEH) structure designed to enhance the efficiency of kinetic energy conversion within the human body. Firstly, the structure and principle of the energy capture device are introduced, and the electromechanical coupling model of the energy harvester is derived using Hamilton's principle. Furthermore, the system is numerically simulated, and the voltage output characteristics of the piezoelectric unit and the electromagnetic unit are analyzed by using the finite element analysis software. Finally, the experimental setup of the (HP-EEH) is constructed, and the voltage output characteristics are tested for different swinging angles and positions. The results show that two parts of energy can be captured simultaneously under ultra-low-frequency motion conditions. At a swing angle of 50 degrees, the piezoelectric and electromagnetic units achieved maximum output power values of 14.96 μW at 0.8 Hz and 10.4 μW at 1.2 Hz, respectively. Incorporating the output power of the electromagnetic unit aims to address the power consumption requirements of low-power devices better.

materials science, multidisciplinary,instruments & instrumentation
Wireless energy transfer by resonant inductive coupling

Rikard Vinge

Abstract:This thesis investigates wireless energy transfer systems based on resonant inductive coupling with applications such as charging electric vehicles. Wireless energy transfer can be used to power or charge stationary and moving objects and vehicles, and the interest in energy transfer over the air has grown considerably in recent years. We study wireless energy transfer systems consisting of two resonant circuits that are magnetically coupled via coils. Further, we explore the use of magnetic materials and shielding metal plates to improve the performance of the energy transfer. To ensure that the wireless energy transfer systems are safe to use by the general public, we optimize our systems to maximize the transferred power and efficiency subject to the constraint that the magnetic fields that humans or animals may be exposed to are limited in accordance with international guidelines. We find that magnetic materials can significantly increase the coupling between the two coils and reduce the induced currents and losses in the shielding metal plates. Further, we design wireless energy transfer systems capable of a peak-value power transfer of 1.3 kW with 90% efficiency over an air gap of 0.3m. This is achieved without exceeding the exposure limit of magnetic fields in areas where humans can be present. Higher levels of transferred power is possible if larger magnetic fields are allowed.

Physics,Engineering
Miniaturized Low-Frequency Communication System Based on the Magnetoelectric Effect

Guohao Zi,Zhibo Ma,Yinan Wang,Yuanhang Wang,Ziqiang Jia,Shanlin Zhao,Dishu Huang,Tao Wang

DOI: https://doi.org/10.3390/mi14101830

2023-09-26

Abstract:Recently, the realization of electromagnetic wave signal transmission and reception has been achieved through the utilization of the magnetoelectric effect, enabling the development of compact and portable low-frequency communication systems. In this paper, we present a miniaturized low-frequency communication system including a transmitter device and a receiver device, which operates at a frequency of 44.75 kHz, and the bandwidth is 1.1 kHz. The transmitter device employs a Terfenol-D (80 mm × 10 mm × 0.2 mm)/PZT (30 mm × 10 mm × 0.2 mm)/Terfenol-D glued composite heterojunction magnetoelectric antenna and the strongest radiation in the length direction, while the receiver device utilizes a manually crafted coil maximum size of 82 mm, yielding a minimum induced electromagnetic field of 1 pT at 44.75 kHz. With an input voltage of 150 V, the system effectively communicates over a distance of 16 m in air and achieves reception of electromagnetic wave signals within 1 m in simulated seawater with a salinity level of 35% at 25 °C. The miniaturized low-frequency communication system possesses wireless transmission capabilities, a compact size, and a rapid response, rendering it suitable for applications in mining communication, underwater communication, underwater wireless energy transmission, and underwater wireless sensor networks.
Characterization of wireless power transfer based on Fano resonant-like surface

yihao wei,Lina Chen,Yongqiang Chen,Yanhong Liu,Fusheng Deng,Xiaoqiang Su,lijuan dong

DOI: https://doi.org/10.1088/1361-6463/ad233a

2024-01-27

Journal of Physics D Applied Physics

Abstract:This paper presents a new way to enhance the transmission efficiency of a dual-coils wireless power transfer system. That method is to introduce a Fano resonant-like surface in the dual-coils wireless power transfer system. This surface, positioned opposite the transmission direction of the transmitter coil in the system, adopts a four-armed helical structure. The results demonstrate that introducing the Fano resonant-like surface significantly enhances system transmission efficiency, attributed to two primary factors. First, the Fano local resonance effect in the dual-coils wireless power transfer system with Fano resonant-like surface leads to the enhance the transmission efficiency. Second, the Fano resonant-like surface shields the energy propagation of the nearby magnetic field in the direction opposite to transmission. Further, compared to a wireless power transfer system comprising only two coils, the overall improvement in transmission efficiency is 30 to 40%. Owing to its simplicity, more compact size, cost-effectiveness, and ease of integration without having to be placed between the transmitting and receiving coils, the Fano resonant-like surface can lay the groundwork for practical applications in wireless charging.

physics, applied
Study of a piezoelectric energy harvesting collaborative strategy based on the synergy of multi‐frequency technique and magnetic nonlinear technique

Jianming Wen,Nan Wei,Yaru Ding,Xinhui Li,Jianping Li,Jijie Ma,Zhonghua Zhang,Guangming Cheng,Yili Hu

DOI: https://doi.org/10.1002/adem.202301154

IF: 3.6

2023-10-03

Advanced Engineering Materials

Abstract:For the purpose of improving the operating bandwidth and output power of piezoelectric vibration energy harvesters (PVEHs) in low‐frequency environment, a novel energy harvesting collaborative strategy based on the synergy of multi‐frequency technique and magnetic nonlinear technique is proposed. In order to reveal the working mechanism of the proposed strategy and determine the influence law of the key parameters on the output performances of system, theoretical modelling, simulation analysis and experiments have been carried out. This study proved the feasibility of the two techniques cooperating and complementing each other on the mechanism level, and optimized the ability of the inner and outer beams to capture energy under the action of the pair of magnets on the structural level. After the optimization of key parameters, the output performance of the proposed PVEH utilizing multi‐frequency and magnetic structure is higher than the counterpart only based on multi‐frequency cantilever structure. In an optimal configuration, the fabricated prototype can finally obtain a maximum power of 2.68 mW and a bandwidth of 1.39 Hz under 0.2g acceleration with 0.03 MΩ load resistance. The proposed piezoelectric energy harvesting collaborative strategy can improve the output performance of piezoelectric vibration energy in practical vibration application environments. This article is protected by copyright. All rights reserved.

materials science, multidisciplinary
A piezoelectric wind energy harvester excited indirectly by a coupler via magnetic-field coupling

Junwu Kan,Weilin Liao,Shuyun Wang,Song Chen,Xin Huang,Zhonghua Zhang

DOI: https://doi.org/10.1016/j.enconman.2021.114250

IF: 10.4

2021-07-01

Energy Conversion and Management

Abstract:Energy harvesting from wind-induced vibration energy using piezoelectric materials has received great attention because of the self-powered demand for wireless sensor networks. To improve the reliability, output performance and environmental adaptability (or designability of the structure), a piezoelectric wind energy harvester excited indirectly by a coupler via magnetic-field coupling (MC-PWEH) is proposed in this paper. The MC-PWEH is mainly composed of a piezoelectric transducer and a coupler consisting of a flexible beam, a cylinder, some exciting magnets and added coupler mass. By introducing the interaction of the piezoelectric transducer sealed in the chamber and the cylinder via the magnetic coupling, the interactive vortex-induced vibration (VIV) and galloping is realized and the composite vibration energy is transformed into electric energy. The feasibility of the structure and principle of the MC-PWEH is proved through theoretical simulations and experiments. The results indicated that the piezoelectric transducer began to oscillate strongly and generate fairly high output voltage when the wind speed exceeded a low critical wind speed, accompanied by a coupling phenomenon of VIV and galloping, and then finally converged to a stable value when the wind speed exceeded a high critical value. Moreover, the critical wind speeds, bandwidth of wind speed, natural frequency and power generation performance of the MC-PWEH could be adjusted by changing the structural parameters. Under the transducer proof mass of 50 g, the optimal wind speed bandwidth for the MC-PWEH to output voltage greater than 3.5 V obtained was 25.84 m⋅s−1 that occupies 86.12% of the experimental wind speed bandwidth. The achieved maximum output power was 4.73 mW at the optimal external load resistance of 1000 kΩ and wind speed of 24 m⋅s−1.

energy & fuels,thermodynamics,mechanics

Basaloid squamous cell carcinoma versus basal cell adenocarcinoma of the oral cavity.

A study of the self-coupling magnetic resonance coupled wireless power transfer

Design and Optimization of a Wireless Power Transfer System with a High Voltage Transfer Ratio

Wireless energy transfer system based on metglas/PFC magnetoelectric laminated composites

High efficiency class-E RF power amplifier for wireless power transfer system

Performance Analysis and Experimental Verification of Mid-Range Wireless Energy Transfer Through Non-Resonant Magnetic Coupling

Great Enhancement of Energy Harvesting Properties of Piezoelectric/Magnet Composites by the Employment of Magnetic Concentrator

Magnetic Pendulum Arrays for Efficient Wireless Power Transmission

Wireless Power and Information Dual Transfer System Via Magnetically Coupled Resonators

Magnetic Energy Coupling System Based on Micro-Electro-Mechanical System Coils

An Optimal Design Method for Improving the Efficiency of Ultrasonic Wireless Power Transmission during Communication

A Mechanical Antenna for Long-Wave Communication by Integrating Piezoelectric Material and Magnets

Enhanced SLF radiation efficiency in a piezoelectrically driven magnetic pendulum transmitter

Design and research of hybrid piezoelectric-electromagnetic energy harvester based on magnetic couple suction-repulsion motion and centrifugal action

Low-frequency piezoelectric energy harvesting from coupled longitudinal-transverse vibration of two magnetic coupling-based orthogonal beams

A hybrid piezoelectric-electromagnetic body energy harvester: Design and experiment validation

Wireless energy transfer by resonant inductive coupling

Miniaturized Low-Frequency Communication System Based on the Magnetoelectric Effect

Characterization of wireless power transfer based on Fano resonant-like surface

Study of a piezoelectric energy harvesting collaborative strategy based on the synergy of multi‐frequency technique and magnetic nonlinear technique

A piezoelectric wind energy harvester excited indirectly by a coupler via magnetic-field coupling