Tunable Electrical Properties of Embossed, Cellulose-Based Paper for Skin-like Sensing
Tongfen Liang,Xiyue Zou,Ramendra Kishor Pal,Jingjin Xie,Maame Konadu Assasie-Gyimah,Jiaqi Liu,Weijian Guo,Chuyang Chen,Max Tenorio,Daniel Sullivan,Anna Root,Paul Stansel,Anne Q. McKeown,George J. Weng,William W. Sampson,Assimina A. Pelegri,Aaron D. Mazzeo
DOI: https://doi.org/10.1021/acsami.0c15073
2020-11-04
Abstract:This article describes a process of fabricating highly porous paper from cellulosic fibers and carbon black (CB) with tunable conductivity. By embossing such paper, its porosity decreases while its conductivity increases. Tuning the porosity of composite paper alters the magnitude and trend of conductivity over a spectrum of concentrations of conductive particles. The largest increase in conductivity from 8.38 × 10<sup>–6</sup> to 2.5 × 10<sup>–3</sup> S/m by a factor of ∼300 occurred at a percolation threshold of 3.8 wt % (or 0.36 vol %) with the composite paper plastically compressed by 410 MPa, which caused a decrease of porosity from 88% to 42% on average. Our composite paper showed stable piezoresistive responses within a broad pressure range from 1 kPa up to 5.5 MPa for 800 cycles. The piezoresistive sensitivities of the composite paper were dependent on concentration and decreased with pressure. Composite paper with 7.5 wt % CB had sensitivities of −0.514 kPa<sup>–1</sup> over applied pressures ranging from 1 to 50 kPa and −0.215 kPa<sup>–1</sup> from 1 to 250 kPa. This piezoresistive paper with embossed patterns enabled touch sensing and detection of damage from darts and punches. Understanding the percolation behavior of three-phase composites (cellulosic fibers/conductive particles/air) and their response to damage, pressure, and processing conditions has the potential to enable scalable applications in prosthetics and robotics, haptic feedback, or structural health monitoring on expansive surfaces of buildings and vehicles.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c15073?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c15073</a>.Picture of paper making, samples, picture of testing in an environmental chamber; SEM images; average conductivity of composite paper; comparison of the electrical conductivity; comparison of composite paper at 1, 1.4, 2, 2.7, 7.5, 10.5, 14.6, 20.5, 28.6, and 40 wt % concentrations from 8 samples; further analysis of conductivity; comparison of composite paper curve fitting of conductivity; pressure sensitivities of composite paper during loading and unloading at pressure ranges of 1–250 and >250 kPa and 1–50 kPa; comparison of some pressure sensor; pressure-response of 7.5 wt % composite paper; setup for shooting darts into the dartboard; average increase in resistance of Rings 1–4; electrical potential changes of a 0.5 mm thick plate with 2 mm holes to model darts; FEA simulation results of resistance change of composite sheet; simplified model of a square plate with a hole for the punctured composite paper; electrical potential changes of a 0.5 mm thick plate with holes in diameter <i>D</i> ranging from 0 to 12 mm; resistance change of punctured composite paper verse the radius of the hole by experiment, simulation, and analytical calculation; optical images of cellulosic fibers taken by MorFi fiber analyzer; and effective length of samples determined by COMSOL simulation (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c15073/suppl_file/am0c15073_si_001.pdf">PDF</a>)Demonstration of capacitive sensors fabricated by conductive foam paper (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c15073/suppl_file/am0c15073_si_002.mp4">MP4</a>)Demonstration of using embossed conductive foam paper as a dartboard to detect damage and impact (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c15073/suppl_file/am0c15073_si_003.mp4">MP4</a>)This article has not yet been cited by other publications.
materials science, multidisciplinary,nanoscience & nanotechnology