Abstract:Organic-inorganic metal halide perovskite solar cells (PSCs) have been widely studied due to their excellent photoelectric conversion performance, but the inherent chemical instability of CH(NH 2 ) 2 PbI 3 (FAPbI 3 ) has hindered its long-term development. In particular, the surface interface of the membrane has prominent humidity sensitivity due to lower activation energy, the defect of the surface interface has a strong correlation with the film stability, and the treatment result of the defect is one of the key factors to improve the long-term stability. FAPbI 3 suffers phase transition from black perovskite phase to yellow non-perovskite phase at room temperature, and the moisture will accelerate this phase transition. Interface engineering is one of the common methods to improve the stability of perovskite solar cells. In addition to interface engineering, there is also a strategy of stacking a two-dimensional (2D) perovskite layer on the surface for interface passivation. However, the preparation methods of 2D perovskite layer are most limited. In this paper, through the preparation process of the whole solution method and post-treatment mode of annealing were adopted, the hybrid perovskite solar cells of vitamin perovskite were successfully prepared. FAPbI 3 perovskite surface was uniformly spin-coated with butylamine iodide (BAI) solution, and the formation of 2D perovskite was driven on the surface of FAPbI 3 perovskite. Due to the passivation of 2D perovskite layer on the defects at the surface interface, the carrier non-radiative recombination is reduced, so that the carrier lifetime is greatly improved. Due to the hydrophobicity of long chain molecules in 2D perovskite, the long-term stability of the device has been significantly improved. Consequently, the unencapsulated device containing 2D perovskite layer remained above 80% after working nearly 1000 hours of relative humidity (RH) of 60% in ambient air at room temperature. The 2D perovskite layer can significantly improve the long-term stability of the film without affecting the charge carrier transport performance. This method to improve the stability of the device by constructing 2D perovskite layer is in line with the requirements and development trend of high-quality perovskite solar cells, and is a strategy with great development potential.

Growth of 2D passivation layer in FAPbI3 perovskite solar cells for high open-circuit voltage

Growth of 1D Nanorod Perovskite for Surface Passivation in FAPbI 3 Perovskite Solar Cells

Constructing 2D passivation layer on perovskites based on 3-chlorobenzylamine enables efficient and stable perovskite solar cells

Synergetic Co‐Modulation of Crystallization and Co‐Passivation of Defects for FAPbI 3 Perovskite Solar Cells

Preparation of 2D Perovskite Layer by Solution Method to Improve the Stability of FAPbI 3 Perovskite Solar Cells

High-performance FAPbBr3 Perovskite Solar Cells Using Dual-Function Bathocuproine Interlayer for Surface Passivation and Energy Level Alignment

Direct Surface Passivation of Perovskite Film by 4-Fluorophenethylammonium Iodide toward Stable and Efficient Perovskite Solar Cells

Surface passivation of FAPbI3-rich perovskite with caesium iodide outperforms bulk incorporation

3D Perovskite Passivation with a Benzotriazole-Based 2D Interlayer for High-Efficiency Solar Cells

A Self‐Assembled 3D/0D Quasi‐Core–Shell Structure as Internal Encapsulation Layer for Stable and Efficient FAPbI 3 Perovskite Solar Cells and Modules

ZnO/SnO2 bilayer electron transport layer strategy to improve the performance of FAPbI3 solar cell

Surface Passivation with Tailoring Organic Potassium Salt for Efficient FAPbI3 Perovskite Solar Cells and Modules

Fluorinated organic ammonium salt passivation for high-efficiency and stable inverted CsPbI2Br perovskite solar cells

Perovskite seeding growth of formamidinium-lead-iodide-based perovskites for efficient and stable solar cells

Enhanced Efficiency and Stability of Inverted CsPbI2Br Perovskite Solar Cells Via Fluorinated Organic Ammonium Salt Surface Passivation.

A Self-Assembled 3D/0D Quasi-Core-Shell Structure As Internal Encapsulation Layer for Stable and Efficient FAPbI3 Perovskite Solar Cells and Modules

Tailoring Low‐Dimensional Perovskites Passivation for Efficient Two‐Step‐Processed FAPbI3 Solar Cells and Modules

Nanoscale phase management of the 2D/3D heterostructure toward efficient perovskite solar cells

Dual-passivation strategy on CsPbI2Br perovskite solar cells for reduced voltage deficit and enhanced stability

Surface defect passivation by 1,8-Naphthyridine for efficient and stable Formamidinium-based 2D/3D perovskite solar cells

Stable α‐FAPbI3 via porous PbI2 for efficient perovskite solar cells