The "symbiotic phase" in light of current infancy research.

F. Pine

1986-11-01

Bulletin of the Menninger Clinic

Abstract:Le phenomene «symbiotique» dans la toute petite enfance (fusion, absence de limites entre la mere et l'enfant) n'est pas incompatible avec les resultats des recherches montrant le remarquable developpement cognitif du nourrisson. Tentative de redefinition du concept de «stade» (ou «phase»)

What problem does this paper attempt to address?

Comparing and Optimizing Municipal Solid Waste (MSW) Management Focused on Air Pollution Reduction from MSW Incineration in China.

Ming Zhang,Junxiao Wei,Huan Li,Yang Chen,Jianguo Liu

DOI: https://doi.org/10.1016/j.scitotenv.2023.167952

2024-01-01

Abstract:China is the largest developing country in the world, and its municipal solid waste (MSW) has increased with a compound annual growth rate of 5.1 % since 1980. Incineration, which has the advantages of mass- and volume-reduction as well as energy and heat recovery, has become the mainstream environmentally sound treatment method in China. However, air pollution emissions are the primary reason for limiting MSW incineration (MSWI). Currently, the Chinese government is devoted to comprehensively implementing MSW classification. However, the classification model and the future MSW reduction rate are not yet clear. In this study, we project scenarios of air pollution emissions until 2030 based on the different MSW classification models (MSW reduction rates) and diffusion rates of ultra-low emission technology. A total of 6011 tons (t) of particulate matter, 25,881 t of SO2, 14,915 t of CO, 17,167 t of HCl, and 200,166 t of NOx will be emitted in 2030 under the business-as-usual (BAU) scenario, and air pollutants will not peak under this scenario. Air pollutants will reduce by 11 % of the BAU scenario by only implementing an MSW reduction of 20 % (JPN-model). The optimal scenario (DEU-model, increasing the efficiency of material recovery and upgrading air pollution control devices) means that air pollutants will be reduced by 83.2-96.2 % from the base amount under the BAU scenario. These results provide references for MSW management and air pollution emission reduction from the aspects of MSW classification and technology upgrades in China.
A comprehensive emission inventory of hazardous air pollutants from municipal solid waste incineration in China

Zhiqiang Fu,Shumin Lin,Hezhong Tian,Yan Hao,Bobo Wu,Shuhan Liu,Lining Luo,Xiaoxuan Bai,Zhihui Guo,Yunqian Lv

DOI: https://doi.org/10.1016/j.scitotenv.2022.154212

2022-06-01

Abstract:The Hazardous air pollutants (HAPs) released from increasing municipal solid waste incineration (MSWI) plants have drawn great concerns in China. However, a full picture of their emission characteristics is still urgently needed, especially after the implementation of stricter emission limits on MSWI. In this study, a comprehensive historical emission inventory of HAPs emitted from MSWI plants in China during the period of 2006-2017 was dedicatedly established by integrating with detailed plant-level activity data and renewed localized emission factors. Overall, HAPs emissions initially increased with years, then peaked or slowed increase in the year 2014, but leveled off after 2016 due to the gradually and fully implementing of newly revised national emission standard (GB18485-2014) applied to mainland China and much stricter local standards for several provinces and cities. It was estimated that totally 50,716 tons (t) of NOx, 13,026 t of CO, 7988 t of SO2, 4399 t of PM, 1943 t of HCl, 9916 kg of Pb, 5901 kg of Mn, 4805 kg of Cu, 3574 kg of Cr, 3329 kg of Ni, 2154 kg of Hg, 1168 kg of Cd, 862 kg of As, 409 kg of Co, 216 kg of Sb, 13 kg of Tl, and 19 g toxic equivalent quantity of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans were emitted from 337 MSWI plants scattered in 30 provinces of mainland China in 2017, respectively. HAPs emissions were heavily concentrated in developed coastal provinces and cities. Scenario analysis highlighted the importance of continuous improvement and upgrade on advanced air pollution control devices and MSWI management to meet the future ultra-low emission limits and minimize the harmful impacts of HAPs on atmospheric environment and public health.

environmental sciences
IL-6 and metabolism—new evidence and new questions

A. Krook

DOI: https://doi.org/10.1007/s00125-008-1019-7

IF: 8.2

2008-05-06

Diabetologia

Abstract:
Disease Outcome Subsequent to Primary and Secondary Urogenital Infection with Murine or Human Biovars ofChlamydia trachomatis

K. H. Ramsey,J. DeWolfe,Rena D. Salyer

DOI: https://doi.org/10.1128/IAI.68.12.7186-7189.2000

2000-12-01

Infection and Immunity

Abstract:ABSTRACT A susceptible strain of mice infected intravaginally with the mouse pneumonitis biovar of Chlamydia trachomatis became infertile and sustained high rates of hydrosalpinx formation regardless of prior infection with a human serovar. Conversely, susceptible mice infected with human serovars remained fertile unless challenged with a homologous human serovar.
Toxicological risk by inhalation exposure of air pollution emitted from China's Municipal Solid Waste Incineration.

Qi Zhou,Jianxun Yang,Miaomiao Liu,Yang Liu,Stefanie Sarnat,Jun Bi

DOI: https://doi.org/10.1021/acs.est.8b03352

IF: 11.4

2018-01-01

Environmental Science & Technology

Abstract:Municipal solid waste (MSW) incineration has developed rapidly in China. However, the air pollution-related health risks attributable to MSW incinerators are still far from known. In this context, an MSW incineration emission inventory was compiled using plant-level activity data and localized emission factors. Subsequently, Gaussian Plume Model and Risk Quotients Model were utilized to calculate the spatialized hazard index (HI) and carcinogenic risk (CR). Altogether, 76449 tons (t) of NOX, 25725 t of SO2, 16937 t of CO, 9279 t of HCl, 5629 t of particulate matter, 33 t of Cr, 33 t of Pb, 20 t of Hg, 6 t of Cd, 4 t of Ni, 0.4 t of As, and 94 g-toxic equivalent quantity of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans were emitted in 2015. The national average HI was 1.88 X 10(-2), which was far lower than the acceptable leve (HI <= 1). However, the national average CR was 5.71 X 10(-6), which was approximately five times higher than the acceptable level (CR <= 1 X 10(-6)). The spatial heterogeneity of health risks was observed. The results enrich spatial dimensions of prior estimates and provide policy implications from the aspects of accelerating technology upgrades, strengthening emission standards, optimizing site selection and enhancing risk communication.
Temporal and Spatial Analysis of Anthropogenic Mercury and CO 2 Emissions from Municipal Solid Waste Incineration in China: Implications for Mercury and Climate Change Mitigation

GUO Jianbo,LIU Liyuan,ZHANG Guangru,YUE Rongwu,WANG Tongzhe,ZHANG Xiujin,YANG Shitong,ZHANG Yitao,WANG Kaiyue,LONG Hongfei,FENG Qingzhong,CHEN Yang

DOI: https://doi.org/10.1016/j.envint.2023.108068

IF: 11.8

2023-06-27

Environment International

Abstract:The contribution of municipal solid waste incineration (MSWI) to anthropogenic mercury and CO 2 emissions have become increasingly important over the past decade. This study developed an inventory of anthropogenic mercury emissions and CO 2 emissions during the period of 2014-2020, of MSWI process in China using a bottom-up inventory at the plant level. Overall, national MSWI anthropogenic mercury emissions increased from 2014 to 2020 by province. It was estimated that total 8321.09 kg of anthropogenic mercury emissions from 548 MSWI plants were scattered in 31 provinces of mainland China in 2020. The average intensity of mercury emission in China was 0.06 g·t -1 in 2020, which was much lower than the pre-2010 level. Furthermore, the increased CO 2 emission generated by MSWI from 2014 to 2020 is 1.97 times. Anthropogenic mercury emissions and CO 2 emissions were concentrated mainly in developed coastal provinces and cities. The general uncertainty of national mercury emissions and CO 2 emissions was estimated to be -123% to 323% and -130% to 335%, respectively. Furthermore, future emissions were predicted from 2030 to 2060 based on different scenarios of the independent and collaborative effects of control proposals, the results indicate that the enhancement of advanced air pollution control technologies and effective management of MSWI represent pivotal factors in realizing future reductions in CO 2 and mercury emissions. The findings will supplement those for mercury and CO 2 emissions, and be useful for relevant policy-making and to improve urban air quality, as well as human health.

environmental sciences
National and Provincial Dioxin Emissions from Municipal Solid Waste Incineration in China

Junxiao Wei,Huan Li,Jianguo Liu,Rigang Zhong

DOI: https://doi.org/10.1016/j.scitotenv.2022.158128

IF: 9.8

2022-01-01

The Science of The Total Environment

Abstract:China presently lacks an up-to-date regional inventory of dioxin emissions from municipal solid waste incineration (MSWI), although MSWI has grown rapidly in recent decades. Based on dioxin concentrations from the official website for governments and enterprises, we created an inventory of dioxin emissions from 29 areas in mainland China. MSWI released a total of 22.56 g I-TEQ of dioxins in 2020. According to Monte Carlo simulation, the dioxin emissions with 95 %, 75 %, and 50 % certainty are 17.03-31.62, 19.24-27.71, and 20.43-25.96 g I-TEQ, respectively. Notably, Guangdong, Zhejiang, and Jiangsu provinces accounted for 38.8 %. The primary regions with considerable dioxin emission per capita and density are Zhejiang and Shanghai. Furthermore, Jilin and Heilongjiang provinces are the top two regions in terms of dioxin emissions per unit of billion gross domestic product. These indicators were affected significantly by the quantity of MSW generated and incinerated (MSWGI), capacity and operating years of incinerators, and degrees of air pollution control devices (APCDs). Dioxin emission factors (EFs) were about 100 times lower in 2020 than in 2004. Note, however, that there is a gap in dioxin EFs between China and European nations. We have proposed that MSW source classification, stable operation conditions of incinerators and APCDs, categories of incinerators selection, and technological upgrading should be China's major measures to curb dioxin emissions. Moreover, with the future increment in the quantity of MSWGI, it is essential to completely reinvent the dioxin monitoring program.
Estimation of Reduced Greenhouse Gas Emission from Municipal Solid Waste Incineration with Electricity Recovery in Prefecture- and County-Level Cities of China.

Qing Zhao,Weihao Tang,Mengjie Han,Wenjing Cui,Lei Zhu,Huaijun Xie,Wei Li,Fengchang Wu

DOI: https://doi.org/10.1016/j.scitotenv.2023.162654

IF: 9.8

2023-01-01

The Science of The Total Environment

Abstract:Municipal solid waste (MSW) without proper managements could be a significant source of greenhouse gas (GHG) emissions. MSW incineration with electricity recovery (MSW-IER) is recognized as a sustainable way to utilize waste, but its effectiveness on reducing GHG emissions at the city scale in China remain unclear due to limited data of MSW compositions. The aim of the study is to investigate reduction potential of GHG from MSW-IER in China. Based on the MSW compositions covering 106 Chinese prefecture-level cities during the period of 1985 to 2016, random forest models were built to predict MSW compositions in Chinese cities. MSW compositions in 297 cities of China from 2002 to 2017 were predicted using the model trained by a combination of socio-economic, climate and spatiotemporal factors. Spatiotemporal and climatic factors (such as economic development level, precipitation) accounted for 6.5 %-20.7 % and 20.1 %-37.6 % to total contributions on MSW composition, respectively. The GHG emissions from MSW-IER in each Chinese city were further calculated based on the predicted MSW compositions. The plastic is the main GHG emission source, accounting for over 91 % of the total emission during 2002-2017. Compared to baseline (landfill) emission, the GHG emission reduction from MSW-IER was 12.5 x 107 kg CO2-eq in 2002 and 415 x 107 kg CO2-eq in 2017, with an average annual growth rate of 26.3 %. The results provide basic data for esti-mating GHG emission in MSW management in China.
Environmental Impact Assessment of the Incineration of Municipal Solid Waste with Auxiliary Coal in China.

Yan Zhao,Wei Xing,Wenjing Lu,Xu Zhang,Thomas H. Christensen

DOI: https://doi.org/10.1016/j.wasman.2012.05.012

IF: 8.816

2012-01-01

Waste Management

Abstract:The environmental impacts of waste incineration with auxiliary coal were investigated using the life-cycle-based software, EASEWASTE, based on the municipal solid waste (MSW) management system in Shuozhou City. In the current system, MSW is collected, transported, and incinerated with 250 kg of coal per ton of waste. Based on observed environmental impacts of incineration, fossil CO(2) and heavy metals were primary contributors to global warming and ecotoxicity in soil, respectively. Compared with incinerators using excess coal, incineration with adequate coal presents significant benefits in mitigating global warming, whereas incineration with a mass of coal can avoid more impacts to acidification, photochemical ozone and nutrient enrichment because of increased electricity substitution and reduced emission from coal power plants. The "Emission standard of air pollutants for thermal power plants (GB13223-2011)" implemented in 2012 introduced stricter policies on controlling SO(2) and NO(x) emissions from coal power plants. Thus, increased use of auxiliary coal during incineration yields fewer avoided impacts on acidification and nutrient enrichment. When two-thirds of ash is source-separated and landfilled, the incineration of rest-waste presents better results on global warming, acidification, nutrient enrichment, and even ecotoxicity in soil. This process is considered a promising solution for MSW management in Shuozhou City. Weighted normalized environmental impacts were assessed based on Chinese political reduction targets. Results indicate that heavy metal and acidic gas emissions should be given more attention in waste incineration. This study provides scientific support for the management of MSW systems dominated by incineration with auxiliary coal in China.
Curbing dioxin emissions from municipal solid waste incineration: China's action and global share.

Junxiao Wei,Huan Li,Jianguo Liu

DOI: https://doi.org/10.1016/j.jhazmat.2022.129076

IF: 13.6

2022-01-01

Journal of Hazardous Materials

Abstract:China generates the world's second-largest amount of municipal solid waste (MSW) and incinerates the largest quantity of MSW. However, data on the latest dioxin emissions from MSW incineration (MSWI) and the related global share were lacking. In the context of MSW classification, distinguishing the long-term MSW generation and incineration quantity, and dioxin emissions was necessary for macro-control and policy-making by the Chinese Government. By considering population size and GDP per capita, China's MSW generation toward 2050 was projected based on Monte Carlo simulation. Moreover, dioxin emission factors were also assumed based on the diffusion rate of four grades of air pollution control devices (APCDs). Finally, we show that the quantity of China's MSW generation in 2050 will be 363.50 million tonnes (Mt) with 341.06-382.45 Mt of 75% certainty. China's dioxin emissions from MSWI were approximately 15.46 g I-TEQ in 2019, which accounted for 26.1% of total emissions from global MSWI. We discuss dioxin emission reduction scenarios depending on MSW diversion and APCD upgrades. China's dioxin emissions will be 70.38 g I-TEQ for the business-as-usual scenario, and the dioxin emissions will be 9.29 g I-TEQ (within the range of 8.88-9.64 g I-TEQ) for the optimal scenario in 2050. Moreover, in 2050, the APCD diffusion rate will account for 98.8% of the sensitivity of dioxin emissions from China's MSWI. According to the assumed scenarios, there is a dioxin emission reduction potential of 18.6% and 86.8% in 2050 by MSW diversion alone and maximum APCD upgrades combined with food waste diversion, respectively.
Assessing the carbon reduction potential of municipal solid waste management transition: Effects of incineration, technology and sorting in Chinese cities

Wen Xiao,Tao Liu,Xin Tong

DOI: https://doi.org/10.1016/j.resconrec.2022.106713

2022-10-23

Resources, Conservation and Recyclcing

Abstract:The urban infrastructures of municipal solid waste (MSW) disposal play important roles in carbon reduction and building sustainable cities. China, with the world's largest MSW generation, has witnessed a relatively slow and spatially uneven transition progress of MSW disposal management. This study analysed the MSW disposal management transition and its determinants in Chinese cities of different sizes. Furthermore, the carbon reduction potential of MSW disposal management transition was estimated under different settings of policy reform. The results indicate that the MSW disposal management transition has made faster progress in cities with larger sizes, which could be ascribed to larger contradiction between city development and public service. The prediction results suggest that 73.13%–287.28% of carbon emission could be reduced by various policy reforms compared with the baseline scenario without policy intervention. Moreover, technological transformation should be specially underlined in mega cities, and household sorting should be specially underlined in medium cities.
Municipal Solid Waste Incineration in China and the Issue of Acidification: A Review

Longjie Ji,Shengyong Lu,Jie Yang,Cuicui Du,Zhiliang Chen,Alfons Buekens,Jianhua Yan

DOI: https://doi.org/10.1177/0734242x16633776

2016-01-01

Waste Management & Research

Abstract:In China, incineration is essential for reducing the volume of municipal solid waste arising in its numerous megacities. The evolution of incinerator capacity has been huge, yet it creates strong opposition from a small, but vocal part of the population. The characteristics of Chinese municipal solid waste are analysed and data presented on its calorific value and composition. These are not so favourable for incineration, since the sustained use of auxiliary fuel is necessary for ensuring adequate combustion temperatures. Also, the emission standard for acid gases is more lenient in China than in the European Union, so special attention should be paid to the issue of acidification arising from flue gas. Next, the techniques used in flue gas cleaning in China are reviewed and the acidification potential by cleaned flue gas is estimated. Still, acidification induced by municipal solid waste incinerators remains marginal compared with the effects of coal-fired power plants.
Evaluation of Flue-Gas Treatment Technologies for Municipal Waste Incineration: A Case Study in Changzhou, China

Zongguo Wen,Jinghan Di,Shutong Liu,Juan Han,Jason Chi Kin Lee

DOI: https://doi.org/10.1016/j.jclepro.2018.02.282

IF: 11.1

2018-01-01

Journal of Cleaner Production

Abstract:With increasing trends in using municipal waste incineration (MWI) technologies, more consideration has been given to the problem of harmful byproducts in its flue. In 2014, a new national standard for pollution control of municipal solid waste incineration was released by the Chinese government, which also gives guidance to local governments to establish their own standards. In order to evaluate whether the treatment technologies for MWI flue gas can both meet the new standard and have overall positive environmental impacts across whole life cycle, a waste life cycle assessment (LCA) was conducted for flue gas to compare treatment technologies employed in MWI plants. Based on a case study of a plant in Changzhou China, a model was established using three combinations of technologies: (a) Spray semi dry reactor + activated carbon + filter bag (Scenario 1); (b) Spray semi dry reactor + dry deacidification reactor + activated carbon + filter bag (Scenario 2); (c) selective non-catalytic reduction (SNCR) + spray semi dry reactor + dry deacidification reactor + activated carbon + filter bag (Scenario 3). The study has wide policy implications on how the industry is, or should be, regulated. Normalized results revealed that technologies used in Scenarios 1 and 2 had less overall impacts on the environment and less direct impact from emissions than those of Scenario 3. Energy-conservation and emission reduction index showed that Scenario 2 best fits current conditions and policy goals about energy consumption and air pollutant emission, despite recent regulations for the requirement of including SNCR in incineration plants. The most significant limiting factor is NON, which is in alignment with the results of policy analysis. Integrated analysis showed that although Scenario 2 is the best choice under current circumstances, further improvement in technology are likely to meet with new standards. Policy-makers should comprehensively consider the environmental impacts of the entire life cycle instead of the one-size-fits all standard.(C) 2018 Elsevier Ltd. All rights reserved.
Health Risk Assessment and Projection of Municipal Solid Waste Disposal in China

Jianxun Yang,Yunqi Liu,Yanyan Qiu,Qi Zhou,Miaomiao Liu,Jun Bi

DOI: https://doi.org/10.1289/isee.2022.p-0203

2022-01-01

ISEE Conference Abstracts

Abstract:Background China's Municipal solid waste (MSW) is growing rapidly. Incineration and landfill are two main approaches of MSW disposal and both of them emit different types of ambient pollutants and threaten human health. There lacks systematic health risk assessment and projections of MSW incineration and landfill in China. Methods We established the historical MSW incineration and landfill emission inventories from 2015 to 2017 and used the Gaussian Diffusion Model to simulate the spatial distribution of ambient pollutants. We then used Risk Quotients Model to assess the non-carcinogenic and carcinogenic health risks through inhalation exposure. Besides, we set seven possible MSW incineration development scenarios to predict health risk levels in 2035, considering the effect of population growth, incineration rate, waste classification and recycling, and technology progress. Results The results show that non-carcinogenic risk caused by MSW incineration from 2015 to 2017 was lower than landfill at the national level. Both of them were meet the maximum acceptable level (HI ≤ 1). From 2015 to 2017, carcinogenic risks caused by landfill were 9.42 × 10-6, 9.40 × 10-6, 9.37 × 10-6, nine times larger than the maximum acceptable level (CR ≤ 1×10-6). Carcinogenic risks caused by incineration were 5.71 × 10-6, 7.92 × 10-6, 9.44 × 10-6, five to nine times larger than the maximum acceptable level. Projection results show that compared to the baseline scenario, through classification and recycling, changing incinerator furnace, and improving, national health risk levels will be decreased by 24%, 94% and 97%. Conclusions We assessed the health risks caused by MSF disposal and found MSF incineration a relatively low risk alternative disposal approach compared to waste landfill. In the future, local government should reduce MSF disposal health risks by optimizing the selection of incinerators locations, improving the garbage sorting recycling system, and strengthening information disclosure and communications.
The Growing Importance of Waste-to-energy (WTE) Incineration in China's Anthropogenic Mercury Emissions: Emission Inventories and Reduction Strategies

Yuanan Hu,Hefa Cheng,Shu Tao

DOI: https://doi.org/10.1016/j.rser.2018.08.026

IF: 16.799

2018-01-01

Renewable and Sustainable Energy Reviews

Abstract:Waste-to-energy (WTE) incineration has been increasingly adopted for municipal solid waste (MSW) disposal in China, which already accounts for nearly 40% of the global installed capacity and electricity generation from WTE. This review identifies the growing importance of WTE incineration as a source of anthropogenic mercury emissions in China, summarizes the mercury control practices at WTE facilities, estimates the inventories of mercury emissions from WTE and those after the implementation of the more stringent air emission standards, and recommends key measures to further reduce the mercury emissions from WTE industry in China. WTE incineration in China was estimated to have a mean current mercury emission factor (EF) of 0.083 g/tonne (with 95% confidence intervals of 0.056-0.116 g/tonne) based on the mercury contents in MSW and the typical removal efficiencies of air pollution control devices (APCDs). The total mercury emissions from WTE incineration were estimated to be around 6.1 tonnes in 2016, and were predicted to reach 10.6 tonnes by 2020 based on its fast growth. The recently adopted more stringent emission standard for mercury can help curb the growth in mercury emissions from WTE incineration, while the gradual implementation of the Minamata Convention on Mercury is expected to contribute to significant reduction in the emissions of mercury from WTE incineration in the long run. Current estimations for mercury emission inventories from WTE incineration in China carry large uncertainty due to the overall scarcity of data. Thus, more work should be conducted to better monitor and quantify the mercury contents in MSW, and the mercury removal efficiencies of APCDs and the emission rates of mercury at WTE facilities. Meanwhile, China also needs to develop effective recycling and waste-sorting programs to divert the mercury-containing waste items from entering the incinerators and thus reduce the mercury emissions while promoting waste disposal by WTE.
Air Pollutant Emission Inventory of Waste-to-Energy Plants in China and Prediction by the Artificial Neural Network Approach.

Wenchao Ma,Jicui Cui,Bore Abdoulaye,Yuan Wang,Huibin Du,Athanasios C. Bourtsalas,Guanyi Chen

DOI: https://doi.org/10.1021/acs.est.2c01087

IF: 11.4

2022-01-01

Environmental Science & Technology

Abstract:The waste-to-energy (WTE) plant has been deployed in 205 cities in China. However, it always faces public resistance to be built because of the great concerns on flue gas pollutants (FGPs). There are limited studies on the socioeconomic heterogeneity analysis and prediction models of WTE capacity/ FGP emission inventories (EIs) based on big data. In this study, the incinerator level emission factors (EFs) in 2020 of PM, SO2, NOx, CO, HCl, dioxins, Hg, Cd + Tl, and Sb + As+ Pb + Cr + Co + Cu + Mn + Ni were calculated based on 322,926 monitoring values of all the 481 WTE plants (1140 processing lines) operating in China, with uncertainties in the range of ±34.70%. The EFs were significantly 45-96% lower than the national standard (GB18485-2014) and had negative relationships with local socioeconomic elements, while WTE capacity and FGP EIs had significantly positive correlations. Gross domestic product, area of built district, and municipal solid waste generation were the main driving forces of WTE capacity. The WTE capacity increased by 150% from 2015 to 2020, while the total emission of PM, SO2, CO, dioxins, Hg, and Sb + As + Pb + Cr + Co + Cu + Mn + Ni decreased by 42.46-88.24%. The artificial neural network models were established to predict WTE capacity and FGP EIs in the city level, with the mean square errors ranging from 0.003 to 0.19 within the model validation limits. This study provides data and model support for the formulation of appropriate WTE plans and a pollutant emission control scheme in different economic regions.
Understanding the emission pattern and source contribution of hazardous air pollutants from open burning of municipal solid waste in China

Ke Cheng,Weiwei Hao,Yan Wang,Peng Yi,Jiayu Zhang,Wanwan Ji

DOI: https://doi.org/10.1016/j.envpol.2020.114417

IF: 8.9

2020-08-01

Environmental Pollution

Abstract:The open burning of municipal solid waste (MSW) is common in China. Therein, low–temperature anoxic combustion results in the emission of hazardous air pollutants. This study employed a dilution sampling system to conduct open burning testing on MSW samples from different functional urban areas. Additionally, modified combustion efficiency was used to distinguish smoldering and flaming combustion in two of the most common open burning practices in China: pile–up burning and barrel burning. The sampled pollutants included gaseous pollutants (e.g., CO2, CO, SO2, and NOx) and fine particles (PM2.5). This study also analyzed the carbonization compounds, 9 water–soluble ions, and 8 toxic heavy metals in PM2.5. Emission factors of air pollutants from open burning of different MSW compositions and burning modes were determined. The composition of PM2.5 from MSW open burning comprised average 43.9%, 22.5%, and 0.4% of organic carbon (OC), water–soluble ions, and toxic heavy metals (THMs), respectively. OC was found to be the primary component of PM2.5. Based on localized emission factor database, the emissions and source contribution of open burning of MSW in China were quantified. The open burning of MSW can contribute averaged 8.7%, 16.7%, 3.8%, 1.3% of PM2.5, OC, THMs, and gaseous air pollutants of reported emissions of anthropogenic sources, respectively. This work can complement current anthropogenic emission inventory and assist policy–making.

environmental sciences
Fate of Dioxins in a Municipal Solid Waste Incinerator with State-of-the-art Air Pollution Control Devices in China.

Junxiao Wei,Huan Li,Jianguo Liu

DOI: https://doi.org/10.1016/j.envpol.2021.117798

IF: 8.9

2021-01-01

Environmental Pollution

Abstract:The variation of municipal solid waste (MSW) components and the improvement of incinerators have an obvious effect on dioxin emissions. However, there is a knowledge gap on dioxin distribution characteristics following China's implementation of MSW classification. To reveal the fate of dioxins under ultra-low emission standards in leading cities in China, a systematic investigation was carried out in a typical modern MSW incinerator in Shenzhen, China. The dioxin mass balance was built using improved models, which included expanded samples, e.g., the leachate, the raw gas and raw ash from boiler, and the chemicals and residuals from air pollution control devices (APCDs). The results indicated a positive dioxin balance of 0.88 μg I-TEQ/t MSW according to the conventional method containing fly ash, bottom ash, and stack gas. In the new model revealing dioxin characteristics after APCDs, a higher value of 0.89 μg I-TEQ/t MSW was found due to the leachate, slaked lime, and activated carbon-containing dioxins. The distribution of dioxins in output samples of fly ash, bottom ash, stack gas, and leachate were 149.0 %, 41.8 %, 1.6 %, and 0.6 % of MSW, respectively. For incineration itself, the balance was 0.85 μg I-TEQ/t MSW, which indicated the possible release owing to the "memory effect" for the other two methods. This study provided new insight for the accurate estimation of dioxin emissions and a typical case report of MSW incineration with ultra-low dioxin emissions.
Improved method for calculating CO2 emission from industrial solid wastes combustion system based on fossil and biogenic carbon fraction

Gefei Liu,Qunxing Huang,Kun Song,Yu Pan,Hong Zhang

DOI: https://doi.org/10.1016/j.wasman.2023.12.001

2024-02-15

Abstract:Waste-to-Energy (WtE) technology is the most effective solution for managing non-recyclable wastes through mass burning and energy recovery. Owing to the significant volumes of plastics in China's industrial solid wastes (ISW), a large amount of greenhouse gases (GHG) is generated during the incineration process. Therefore, monitoring GHG emissions from WtE facilities is essential. Owing to the lack of suitable accounting models and characterized fossil carbon fraction (FCF) data, current studies use default values provided by the Intergovernmental Panel on Climate Change's (IPCC), which increases calculation inaccuracies. Therefore, this study established an improved method to accurately account for carbon emissions during solid waste incineration by firstly using radiocarbon dating by accelerator mass spectrometry (AMS) technique to determine the FCF of the solid waste components in China. Monte Carlo analysis was employed to perform the sensitivity analysis, and the results indicated that there was a significant deviation between the measured value and IPCC's default values of FCF, 3.2, 32.48, 93.39, 93.76, 90.49, and 93.8 % for paper, cotton, synthetic textiles, artificial rubber, artificial leather, and plastics, respectively. By replacing coal with ISW in a 2 × 110 t/h circulating fluidized bed boilers, 9.251 × 104 t CO2-eq emissions were reduced, and the carbon emission factor reached 0.56 t CO2-eq/t waste. This study complements the research gap fossil carbon data of wastes in the IPCC guidelines and provides a more accurate and effective way to calculate carbon emissions during ISW incineration treatment.
Analyses on Carbon Emission from Municipal Solid Waste Treatment in China

Huan Li,Yiying Jin

DOI: https://doi.org/10.4028/www.scientific.net/amr.361-363.1030

2012-01-01

Abstract:The carbon emissions from China's MSW management are evaluated with the mass balance model. According to the MSW generation and treatment trends, the future carbon emission and sink are also predicted. The results show that the net equivalent CO2 emission is maintaining at about 150 million tons at recent years, although the MSW generation is growing slowly. MSW incineration for energy production and Landfill gas utilization in landfill sites are the main ways of carbon emission reduction. China's MSW generation will reach 166 million tons, while the equivalent CO2 emission will decease to 144 million tons due to more energy recovery from MSW treatment.

The "symbiotic phase" in light of current infancy research.

Comparing and Optimizing Municipal Solid Waste (MSW) Management Focused on Air Pollution Reduction from MSW Incineration in China.

A comprehensive emission inventory of hazardous air pollutants from municipal solid waste incineration in China

IL-6 and metabolism—new evidence and new questions

Disease Outcome Subsequent to Primary and Secondary Urogenital Infection with Murine or Human Biovars ofChlamydia trachomatis

Toxicological risk by inhalation exposure of air pollution emitted from China's Municipal Solid Waste Incineration.

Temporal and Spatial Analysis of Anthropogenic Mercury and CO 2 Emissions from Municipal Solid Waste Incineration in China: Implications for Mercury and Climate Change Mitigation

National and Provincial Dioxin Emissions from Municipal Solid Waste Incineration in China

Estimation of Reduced Greenhouse Gas Emission from Municipal Solid Waste Incineration with Electricity Recovery in Prefecture- and County-Level Cities of China.

Environmental Impact Assessment of the Incineration of Municipal Solid Waste with Auxiliary Coal in China.

Curbing dioxin emissions from municipal solid waste incineration: China's action and global share.

Assessing the carbon reduction potential of municipal solid waste management transition: Effects of incineration, technology and sorting in Chinese cities

Municipal Solid Waste Incineration in China and the Issue of Acidification: A Review

Evaluation of Flue-Gas Treatment Technologies for Municipal Waste Incineration: A Case Study in Changzhou, China

Health Risk Assessment and Projection of Municipal Solid Waste Disposal in China

The Growing Importance of Waste-to-energy (WTE) Incineration in China's Anthropogenic Mercury Emissions: Emission Inventories and Reduction Strategies

Air Pollutant Emission Inventory of Waste-to-Energy Plants in China and Prediction by the Artificial Neural Network Approach.

Understanding the emission pattern and source contribution of hazardous air pollutants from open burning of municipal solid waste in China

Fate of Dioxins in a Municipal Solid Waste Incinerator with State-of-the-art Air Pollution Control Devices in China.

Improved method for calculating CO2 emission from industrial solid wastes combustion system based on fossil and biogenic carbon fraction

Analyses on Carbon Emission from Municipal Solid Waste Treatment in China