The HLA linkage group.

J. V. van Rood,A. van Leeuwen,A. Termijtelen,J. Keuning

IF: 3.249

1976-07-01

Experimental Hematology

Abstract:

What problem does this paper attempt to address?

Screening dental patients for temporomandibular disorders.

G. Anderson,E. Schiffman

1991-09-01

Abstract:
Influence of dose calculation algorithms on the helical diode array using volumetric‐modulated arc therapy for small targets

Tomohiro Ono,Hideaki Hirashima,Takanori Adachi,Hiraku Iramina,Takahiro Fujimoto,Megumi Uto,Mitsuhiro Nakamura,Takashi Mizowaki

DOI: https://doi.org/10.1002/acm2.14307

2024-02-18

Journal of Applied Clinical Medical Physics

Abstract:Background For patient‐specific quality assurance (PSQA) for small targets, the dose resolution can change depending on the characteristics of the dose calculation algorithms. Purpose This study aimed to evaluate the influence of the dose calculation algorithms Acuros XB (AXB), anisotropic analytical algorithm (AAA), photon Monte Carlo (pMC), and collapsed cone (CC) on a helical diode array using volumetric‐modulated arc therapy (VMAT) for small targets. Materials and methods ArcCHECK detectors were inserted with a physical depth of 2.9 cm from the surface. To evaluate the influence of the dose calculation algorithms for small targets, rectangular fields of 2×100, 5×100, 10×100, 20×100, 50×100, and 100×100 mm2 were irradiated and measured using ArcCHECK with TrueBeam STx. A total of 20 VMAT plans for small targets, including the clinical sites of 19 brain metastases and one spine, were also evaluated. The gamma passing rates (GPRs) were evaluated for the rectangular fields and the 20 VMAT plans using AXB, AAA, pMC, and CC. Results For rectangular fields of 2×100 and 5×100 mm2, the GPR at 3%/2 mm of AXB was 10×100 mm2, the GPR at 3%/2 mm was > 88.1% and comparable for all dose calculation algorithms. For the 20 VMAT plans, the GPRs at 3%/2 mm were 79.1 ± 15.7%, 93.2 ± 5.8%, 94.9 ± 4.1%, and 94.5 ± 4.1% for AXB, AAA, pMC, and CC, respectively. Conclusion The behavior of the dose distribution on the helical diode array differed depending on the dose calculation algorithm for small targets. Measurements using ArcCHECK for VMAT with small targets can have lower GPRs owing to the coarse dose resolution of AXB around the detector area.

radiology, nuclear medicine & medical imaging
Small field output factor measurement and verification for CyberKnife robotic radiotherapy and radiosurgery system using 3D polymer gel, ionization chamber, diode, diamond and scintillator detectors, Gafchromic film and Monte Carlo simulation

Md Abdullah Al Kafi,Mehenna Arib,Akram Al Moussa,Faisal Alzorkany,Mamoun Shehadeh,Mohd Fahmi Mohd Yusof,Belal Moftah

DOI: https://doi.org/10.1016/j.apradiso.2022.110576

Abstract:The dosimetry of small fields has become tremendously important with the advent of intensity-modulated radiation therapy (IMRT) and stereotactic radiosurgery, where small field segments or very small fields are used to treat tumors. With high dose gradients in the stereotactic radiosurgery or radiotherapy treatment, small field dosimetry becomes challenging due to the lack of lateral electronic equilibrium in the field, x-ray source occlusion, and detector volume averaging. Small volume and tissue-equivalent detectors are recommended to overcome the challenges. With the lack of a perfect radiation detector, studies on available detectors are ongoing with reasonable disagreement and uncertainties. The joint IAEA and AAPM international code of practice (CoP) for small field dosimetry, TRS 483 (Alfonso et al., 2017) provides guidelines and recommendations for the dosimetry of small static fields in external beam radiotherapy. The CoP provides a methodology for field output factor (FOF) measurements and use of field output correction factors for a series of small field detectors and strongly recommends additional measurements, data collection and verification for CyberKnife (CK) robotic stereotactic radiotherapy/radiosurgery system using the listed detectors and more new detectors so that the FOFs can be implemented clinically. The present investigation is focused on using 3D gel along with some other commercially available detectors for the measurement and verification of field output factors (FOFs) for the small fields available in the CK system. The FOF verification was performed through a comparison with published data and Monte Carlo simulation. The results of this study have proved the suitability of an in-house developed 3D polymer gel dosimeter, several commercially available detectors, and Gafchromic films as a part of small field dosimetric measurements for the CK system.
Detector-specific correction factors in radiosurgery beams and their impact on dose distribution calculations

Olivia A García-Garduño,Manuel A Rodríguez-Ávila,José M Lárraga-Gutiérrez

DOI: https://doi.org/10.1371/journal.pone.0196393

IF: 3.7

2018-05-15

PLoS ONE

Abstract:Silicon-diode-based detectors are commonly used for the dosimetry of small radiotherapy beams due to their relatively small volumes and high sensitivity to ionizing radiation. Nevertheless, silicon-diode-based detectors tend to over-respond in small fields because of their high density relative to water. For that reason, detector-specific beam correction factors ([Formula: see text]) have been recommended not only to correct the total scatter factors but also to correct the tissue maximum and off-axis ratios. However, the application of [Formula: see text] to in-depth and off-axis locations has not been studied. The goal of this work is to address the impact of the correction factors on the calculated dose distribution in static non-conventional photon beams (specifically, in stereotactic radiosurgery with circular collimators). To achieve this goal, the total scatter factors, tissue maximum, and off-axis ratios were measured with a stereotactic field diode for 4.0-, 10.0-, and 20.0-mm circular collimators. The irradiation was performed with a Novalis® linear accelerator using a 6-MV photon beam. The detector-specific correction factors were calculated and applied to the experimental dosimetry data for in-depth and off-axis locations. The corrected and uncorrected dosimetry data were used to commission a treatment planning system for radiosurgery planning. Various plans were calculated with simulated lesions using the uncorrected and corrected dosimetry. The resulting dose calculations were compared using the gamma index test with several criteria. The results of this work presented important conclusions for the use of detector-specific beam correction factors ([Formula: see text] in a treatment planning system. The use of [Formula: see text] for total scatter factors has an important impact on monitor unit calculation. On the contrary, the use of [Formula: see text] for tissue-maximum and off-axis ratios has not an important impact on the dose distribution calculation by the treatment planning system. This conclusion is only valid for the combination of treatment planning system, detector, and correction factors used in this work; however, this technique can be applied to other treatment planning systems, detectors, and correction factors.
Comparison and Assessment of Profile and Output Factor Measurement for a Frameless Robotic Radiosurgery System Using Different Detectors

X. Zhang,J. Li,R. Yang,L. Liu,Y. Pan,M. Li,J. Wang

DOI: https://doi.org/10.1016/j.ijrobp.2017.06.2386

2017-01-01

Abstract:To compare and assess different detectors for the profile and output factor (OF) measurement for a Cyberknife system, and provide reference and suggestions for selecting and using the correct detectors. Profiles were acquired using the detectors of PTW-60017, PTW-60018, PTW-60019 and IBA-SFD, at different depths for different collimator sizes, with the detectors stem oriented both perpendicular and parallel to the central beam axis. The differences of profiles among different detectors and orientation of detectors were analyzed. Output factors were measured using PTW ionization chamber 30013, 31010, diode detector PTW 60017, PTW60018 and diamond detector 60019 for different fixed aperture collimators from 5 mm to 60 mm at SAD 800 mm and depth of water 50 mm. EBT3 film measured OF at 5 cm depth in a water phantom with a SAD of 800mm was used as reference for comparison. All full width at half maximum (FWHM) of field measured by four detectors in parallel orientation were larger than actual field size. The deviation increased with the size of collimator and measurement depth, with the maximal deviation of 0.6mm. The deviation of FWHM among four detectors increased with the increase of measurement depth, with the maximum deviation of 0.2mm. The penumbra was the smallest for IBA-SFD, and largest for PTW-60019. The maximal deviation of penumbra was 0.3mm. The IBA-SFD agreed with other detectors but tended to over-respond in the out-of-field region when the collimator size was larger than 30mm. Both FWHM and penumbra in perpendicular orientation were smaller than in parallel orientation for PTW-60017, PTW-60018 and PTW-60019, especially for the 5mm collimator. However, the trend was opposite for IBA-SFD. With the increase of collimator aperture, the difference between the right and left penumbra acquired by four detectors increased, with more obvious stem effects observed. A good agreement among the output factors obtained from these five detectors was found for the collimator size more than 30mm, with the deviations less than 1%. When the collimator size was less than 30mm, the deviations of the OF became large and obviously increased with the decrease of the collimator size. The measured OFs of PTW60019 were basically consistent with EBT3 film, with the deviation less than 2%. The OFs were higher for diodes detectors, and much smaller for Ionization chambers than EBT3 film. Similar profiles were acquired by PTW-60017, PTW-60018, PTW-60019 and IBA-SFD, but the detectors’ characteristics and effects of detector orientations should be considered. PTW 30013, 31010, PTW 60017, PTW60018 and 60019 could be directly used for the OFs measurement, when field was greater than 30mm. But if the field was less than 30mm, the measurement results obtained by these detectors need to be corrected. Sensitive volume, the effective measure length and material density of detector affected the measurement of OFs, especially for small filed.
Accurate machine‐specific reference and small‐field dosimetry for a self‐shielded neuro‐radiosurgical system

Peter R. Jermain,Bryan Muir,Malcolm McEwen,Ying Niu,Dalong Pang

DOI: https://doi.org/10.1002/mp.17111

IF: 4.506

2024-05-04

Medical Physics

Abstract:Background The newly available ZAP‐X stereotactic radiosurgical system is designed for the treatment of intracranial lesions, with several unique features that include a self‐shielding, gyroscopic gantry, wheel collimation, non‐orthogonal kV imaging, short source‐axis distance, and low‐energy megavoltage beam. Systematic characterization of its radiation as well as other properties is imperative to ensure its safe and effective clinical application. Purpose To accurately determine the radiation output of the ZAP‐X with a special focus on the smaller diameter cones and an aim to provide useful recommendations on quantification of small field dosimetry. Methods Six different types of detectors were used to measure relative output factors at field sizes ranging from 4 to 25 mm, including the PTW microSilicon and microdiamond diodes, Exradin W2 plastic scintillator, Exradin A16 and A1SL ionization chambers, and the alanine dosimeter. The 25 mm cone served as the reference field size. Absolute dose was determined with both TG‐51‐based dosimetry using a calibrated PTW Semiflex ion chamber and measurements using alanine dosimeters. Results The average radiation output factors (maximum deviation from the average) measured with the microDiamond, microSilicon, and W2 detectors were: for the 4 mm cone, 0.741 (1.0%); for the 5 mm cone: 0.817 (1.0%); for the 7.5 mm cone: 0.908 (1.0%); for the 10 mm cone: 0.946 (0.4%); for the 12.5 mm cone: 0.964 (0.2%); for the 15 mm cone: 0.976 (0.1%); for the 20 mm cone: 0.990 (0.1%). For field sizes larger than 10 mm, the A1SL and A16 micro‐chambers also yielded consistent output factors within 1.5% of those obtained using the microSilicon, microdiamond, and W2 detectors. The absolute dose measurement obtained with alanine was within 1.2%, consistent with combined uncertainties, compared to the PTW Semiflex chamber for the 25 mm reference cone. Conclusion For field sizes less than 10 mm, the microSilicon diode, microDiamond detector, and W2 scintillator are suitable devices for accurate small field dosimetry of the ZAP‐X system. For larger fields, the A1SL and A16 micro‐chambers can also be used. Furthermore, alanine dosimetry can be an accurate verification of reference and absolute dose typically measured with ion chambers. Use of multiple suitable detectors and uncertainty analyses were recommended for reliable determination of small field radiation outputs.

radiology, nuclear medicine & medical imaging
Comparative Analysis of Four Detectors for the Profile Measurement Using CyberKnife

Zhang Xile,Yang Ruijie,Li Jun,Li Mengzhao,Liu Lu,Pan Yuxi,Wang Junjie

DOI: https://doi.org/10.3760/cma.j.issn.0254-5098.2017.09.006

2017-01-01

Abstract:Objective To evaluate four detectors for the off-axis ratio profile measurements of a CyberKnife system, and provide reference and suggestions for selecting and using the correct detectors. Methods Profiles were acquired by using four detectors, PTW-60017, PTW-60018, PTW-60019 and IBA-SFD, at different depths for different collimator sizes, with the detector stem being oriented both perpendicular and parallel to the central beam axis. The differences of profiles and the influence of detector orientation on measurement result were analyzed. Results All full width at half maximum ( FWHM) of field measured by four detectors in parallel orientation was larger than that in actual field size. The deviation was increased with the size of collimator and measurement depth, with the maximum deviation of 1. 9 mm. The maximum deviation of FWHM among four detectors was 0. 2 mm. The penumbra was the smallest for IBA-SFD, and the largest for PTW-60019. The maximum deviation of penumbra was 0. 3 mm. The IBA-SFD tended to over-respond in the out-of-field region when the collimator size was larger than 30 mm. Both FWHM and penumbra in perpendicular orientation were smaller than those in parallel orientation for PTW-60017, PTW-60018 and PTW-60019, especially at 5 mm collimator. However, the trend was opposite for IBA-SFD. With the increase of collimator aperture, the difference between the right and left penumbra acquired by four detectors was increased, with more obvious stem effects. Conclusions Similar profiles were acquired by four detectors, but the detector characteristics and effects of detector orientations should be considered.
Impact of Measurement Conditions and Design Features of IBA Detectors on the Small Radiation Fields Output Factors

V. S. Piskunou,I. G. Tarutin

DOI: https://doi.org/10.52775/1810-200x-2023-99-3-19-27

2023-10-02

Meditsinskaya Fizika

Abstract:The use of modern diagnostic equipment in oncology has made it possible to detect small tumor foci, as well as to detect distant metastases of the disease at an early stage of their formation. In these cases, it becomes possible to refuse surgical interventions, replacing them with stereotactic radiosurgery using radiation therapy devices. In this case, small irradiation fields can be used (from fields less than 1 cm to 4 cm). In such cases, there is a problem of delivering large doses to small foci. It consists in the accuracy of determining the absorbed doses delivered to small targets. The complexity of monitoring the quality of dosimetric support of irradiation with the use of various radiotherapy devices is increasing. Increased requirements are also imposed on the detectors used for measurements. This work has several goals: 1) to study the results of measurements of the output factors using five different detectors of small sizes; 2) to determine the changes in the output factors when using two types of beam collimation (collimator shutters - JAWS and multileaf collimator - MLC) of linear electron accelerators; 3) to study the dependence of the output factors on the source-to-surface distance (SSD), on the depth of measurements and on the type of detectors. The measurements were carried out in 6 MV photon beams with a flattening filter on a TrueBeam linear accelerator. Five IBA detectors were used: two diode detectors (PFD and SFD) and three ionization chambers (CC01, CC04 and CC13). The field sizes varied from 1010 cm to 11 cm. The studies were carried out for the following combinations of parameters: SSD is 100 cm and the measurement depth is 10 cm; SSD is 95 cm and the measurement depth is 5 cm. The fields were formed by JAWS and MLC. The analysis of the obtained results made it possible to compare the data obtained from each detector in similar combinations of measurements. Based on the analysis of the output factors measured by all five detectors, conclusions were drawn about the parameters that affect the change in the output factors.
Quantification of Dosimetry Improvement With or Without Patient Surface Guidance

Ke Sheng,Minsong Cao,Andrew Godley,Mu-Han Lin,Lukas Henze,Laura Hammond,Laurence Delombaerde,Kirsten Hierholz,Jana Kouptsidis

DOI: https://doi.org/10.1016/j.adro.2024.101570

2024-07-14

Abstract:Purpose: Noncoplanar beams and arcs are routinely used to improve dosimetry for intracranial cases, but their application for extracranial cases has been hampered by the risk of collision. This has led to conservative beam selection whose impact on plan dosimetry has not been previously studied. Methods and materials: A full-body 3-dimensional patient surface was acquired using optical cameras for a single lung patient at the time of computed tomography simulation. Eight stereotactic body radiation therapy (SBRT) plans were created for the patient, with varying degrees of noncoplanarity and deliverability. The plans included volumetric modulated arc therapy and intensity modulated radiation therapy (IMRT) plans ranging from simple, coplanar arcs to multiple noncoplanar arcs and IMRT beams. A total of 70 fields were created across the 8 plans, of which 21 fields were undeliverable with a 5-cm buffer. Organs-at-risk (OARs) metrics including R50, Dmax 2 cm from the PTV, lung V20, and chest wall V30 were evaluated. Five expert SBRT dosimetrists from 5 institutions evaluated field deliverability, with or without the guidance of the clearance map. Results: In the dosimetry evaluation, a clear trend in increasing dosimetric compactness and OAR sparing is observed with increasing plan noncoplanarity. R50, Dmax 2 cm, lung V20, and chest wall V30 decreased 41%, 39%, 43%, and 57%, respectively, from plan 1 (2 coplanar partial arcs) to plan 8 (19 noncoplanar IMRT beams). In the observer tests, the expert dosimetrists' ability to accurately discern beam deliverability because of collision significantly increases with the clearance map. The errors in predicting colliding fields were eliminated using the whole-body surface and clearance map, and the user was able to select fields based on plan quality and patient comfort instead of being overly conservative. Conclusion: The study shows that incorporating a personalized, whole-body clearance map in the treatment planning workflow can facilitate the adoption of noncoplanar beams or arcs that benefit the SBRT plan dosimetry.
The relationship between fetal arterial oxygen saturation and heart and skeletal muscle myoglobin concentrations in the ovine fetus.

S. Guiang,J. Widness,K. Flanagan,R. Schmidt,W. Radmer,M. Georgieff

1993-03-01

Abstract:Myoglobin, a hemoprotein found in abundance in the muscle of postnatal animals, increases in concentration in response to hypoxia, thereby protecting tissue from damage. Fetuses exposed to intrauterine hypoxemia are also susceptible to organ damage, but the response of fetal muscle myoglobin to hypoxemia is unknown. To study whether fetal muscle myoglobin concentrations are elevated following intrauterine hypoxemia, we exposed eight chronically catheterized late gestation sheep to a wide range of fetal oxygen levels over 15 to 30 days and correlated the level of fetal oxygenation with heart and skeletal muscle myoglobin concentrations measured at sacrifice. A lower level of fetal oxygenation, expressed as the integrated area under the arterial saturation (SaO2)-time curve, was associated with greater myocardial myoglobin concentration (r = 0.90; P < 0.01). This relationship was not observed for skeletal muscle (r = 0.43; P = ns). A lower level of fetal oxygenation was associated with lower myoglobin:iron (w/w) ratio in skeletal muscle (r = 0.71; P < 0.03), implying less incorporation of iron into myoglobin. A similar relationship was not apparent for cardiac tissue. The higher myocardial myoglobin concentrations found in the more hypoxic fetuses were consistent with previous observations in postnatal animals. This likely represents an intracellular compensatory mechanism for sustaining short-term mitochondrial oxygen delivery in a critical organ with a high rate of oxygen consumption. The lack of myoglobin responsiveness to hypoxia in fetal skeletal muscle may be due to its much lower oxygen consumption rate and activity level.
Angular correction methodology and characterization of a high-resolution CMOS array for patient specific quality assurance on a robotic arm linac

Muhammad Ramish Ashraf,Jochen Krimmer,Laszlo Zalavri,Xuejun Gu,Lei Wang,Cynthia Fu-Yu Chuang

DOI: https://doi.org/10.1002/acm2.14110

Abstract:Purpose: To develop an angular correction methodology and characterize a high-resolution complementary metal-oxide-semiconductor (CMOS) array for patient specific quality assurance on a robotic arm linear accelerator. Methods: Beam path files from the treatment planning software (TPS) were used to calculate the angle of radiation beam with respect to the detector plane. Beams from multiple discrete angles were delivered to the CMOS detector array and an angular dependency look up table (LUT) was created. The LUT was then used to correct for the angular dependency of the detector. An iso-centric 5 mm fixed cone, non iso-centric multi-target fixed cone, 10 mm Iris and a multi-leaf collimator (MLC) based collimated plan were delivered to the phantom and compared to the TPS with and without angular correction applied. Additionally, the CMOS array was compared to gafchromic film and a diode array. Results: Large errors of up to 30% were observed for oblique angles. When angular correction was applied, the gamma passing rate increased from 99.2% to 100% (average gamma value decreased from 0.29 to 0.14) for the 5-mm iso-centric cone plan. Similarly, the passing rate increased from 84.0% to 100% for the Iris plan and from 49.98% to 98.4% for the MLC plan when angular correction was applied. For the multi-target plan, applying angular correction improved the gamma passing rate from 94% to 99.6%. The 5 mm iso-centric fixed cone plan was also delivered to film, and the gamma passing rate was 91.3% when using gafchromic film as the reference dataset, whereas the diode array provided insufficient sampling for this plan. Conclusion: A methodology of calculating the beam angle based on the beam path files was developed and validated. The array was demonstrated to be superior to other quality assurance tools because of its sub-millimeter spatial resolution and immediate read out of the results.
Technical Note: Investigating of dosimetric leaf gap and leaf transmission factor variations across gantry and collimator angles in volumetric modulation arc therapy

Aram Rostami,Mojtaba Barzegar,Muhammad Usman,Satheesh Prasad Paloor,Abbass Yousef Mkanna,Alla Fuad Al‐Sabahi,Rabih Wafiq Hammoud

DOI: https://doi.org/10.1002/acm2.14523

2024-09-13

Journal of Applied Clinical Medical Physics

Abstract:Purpose This study investigates the influence of gantry and collimator angles on the dosimetric leaf gap (DLG) and leaf transmission factor (LTF) in a Varian LINAC equipped with rounded‐end multi‐leaf collimators (MLCs). While Varian guidelines recommend DLG measurements at zero degrees for both gantry and collimator, this research aims to address the knowledge gap by assessing DLG and LTF variations at different gantry and collimator angles. Methods Measurements were conducted using a Varian TrueBeam LINAC with a Millennium 120‐leaf MLC and Eclipse TPS version 16.1. The beams utilized in this study had energies of 6 MV, 10 MV, 6 FFF, and 10 FFF. LTF and DLG were determined using ionization chambers in solid water phantoms at various gantry angles (0°, 45°, 90°, 135°, 180°, 225°, 270°, and 315°). For each gantry angle, measurements were also taken at various collimator angles (0°, 45°, 90°, and 315°). Dosimetric impacts were evaluated through VMAT Picket Fence tests and patient‐specific verification using portal dosimetry for 10 clinical VMAT plans. Results LTF values showed no significant variation across gantry and collimator angles. However, DLG values exhibited notable differences depending on the gantry angle and were independent of the collimator angle. The highest DLG value was observed at a gantry angle of 270 degrees, while the lowest was at 90 degrees. The AXB DLGAverage (averaging seven measurements of DLGs at different gantry angles) model demonstrated the best agreement between measured and calculated dose distributions, indicating the importance of considering averaged DLG values across multiple gantry angles for accurate dose calculations. Conclusion Our study highlights the variability of DLG with gantry angle alterations, contrary to Varian guidelines recommending DLG measurements at zero gantry angle only. We advocate for utilizing an averaged DLG value from measurements across multiple gantry angles, as outlined in our methodology.

radiology, nuclear medicine & medical imaging
Monte Carlo simulation of beam characteristics from small fields based on TrueBeam flattening-filter-free mode

Zhongsu Feng,Haizhen Yue,Yibao Zhang,Hao Wu,Jinsheng Cheng,Xu Su

DOI: https://doi.org/10.1186/s13014-016-0601-2

IF: 4.309

2016-01-01

Radiation Oncology

Abstract:Purpose Through the Monte Carlo (MC) simulation of 6 and 10 MV flattening-filter-free (FFF) beams from Varian TrueBeam accelerator, this study aims to find the best incident electron distribution for further studying the small field characteristics of these beams. Methods By incorporating the training materials of Varian on the geometry and material parameters of TrueBeam Linac head, the 6 and 10 MV FFF beams were modelled using the BEAMnrc and DOSXYZnrc codes, where the percentage depth doses (PDDs) and the off-axis ratios (OARs) curves of fields ranging from 4 × 4 to 40 × 40 cm 2 were simulated for both energies by adjusting the incident beam energy, radial intensity distribution and angular spread, respectively. The beam quality and relative output factor (ROF) were calculated. The simulations and measurements were compared using Gamma analysis method provided by Verisoft program (PTW, Freiburg, Germany), based on which the optimal MC model input parameters were selected and were further used to investigate the beam characteristics of small fields. Results The Full Width Half Maximum (FWHM), mono-energetic energy and angular spread of the resultant incident Gaussian radial intensity electron distribution were 0.75 mm, 6.1 MeV and 0.9° for the nominal 6 MV FFF beam, and 0.7 mm, 10.8 MeV and 0.3° for the nominal 10 MV FFF beam respectively. The simulation was mostly comparable to the measurement. Gamma criteria of 1 mm/1 % (local dose) can be met by all PDDs of fields larger than 1 × 1 cm 2 , and by all OARs of no larger than 20 × 20 cm 2 , otherwise criteria of 1 mm/2 % can be fulfilled. Our MC simulated ROFs agreed well with the measured ROFs of various field sizes (the discrepancies were less than 1 %), except for the 1 × 1 cm 2 field. Conclusions The MC simulation agrees well with the measurement and the proposed model parameters can be clinically used for further dosimetric studies of 6 and 10 MV FFF beams.
Computational and experimental small field dosimetry using a commercial plastic scintillator detector for the 0.35 T MR-linac

Ahtesham Ullah Khan,Indra J Das,Poonam Yadav

DOI: https://doi.org/10.1016/j.ejmp.2024.103403

Abstract:Purpose: Although plastic scintillator detectors (PSDs) are considered ideal dosimeters for small field dosimetry in conventional linear accelerators (linacs), the impact of the magnetic field strength on the response of the PSD must be investigated. Methods: A linac Monte Carlo (MC) head model for a low-field MR-linac was validated for small field dosimetry and utilized to calculate field output factors (OFs). The MC-calculated OFs were compared with the treatment planning system (TPS)-calculated OFs and measured OFs using a Blue Physics (BP) Model 10 commercial PSD and a synthetic diamond detector. The field-specific correction factors, [Formula: see text] , were calculated for the PSD in the presence of a 0.35 T and magnetic field. The impact of the source focal spot size and initial electron energy on the MC-calculated OFs was investigated. Results: Good agreement to within 2 % was found between the MC-calculated OFs and BP PSD OFs except for the 0.415 × 0.415 cm2 field size. The BP PSD [Formula: see text] correction factors were calculated to be within 1 % of unity. For field sizes ≥1.66 × 1.66 cm2, the MC-calculated OFs were relatively insensitive to the focal spot size and initial electron energy to within 2.5 %. However, for smaller field sizes, the MC-calculated OFs were found to differ up to 9.50 % and 7.00 % when the focal spot size and initial electron energy was varied, respectively. Conclusions: The BP PSD was deemed suitable for small field dosimetry in MR-linacs without requiring any [Formula: see text] correction factors.
The role of radiation‐induced charge imbalance on the dose‐response of a commercial synthetic diamond detector in small field dosimetry

Hui Khee Looe,Daniela Poppinga,Rafael Kranzer,Isabel Büsing,Tuba Tekin,Ann‐Britt Ulrichs,Björn Delfs,Dennis Vogt,Jan Würfel,Björn Poppe

DOI: https://doi.org/10.1002/mp.13542

IF: 4.506

2019-05-02

Medical Physics

Abstract:PURPOSE: Discrepancy between experimental and Monte Carlo simulated dose-response of the microDiamond (mD) detector (type 60019, PTW Freiburg, Germany) at small field sizes has been reported. In this work, the radiation-induced charge imbalance in the structural components of the detector has been investigated as the possible cause of this discrepancy.MATERIALS AND METHODS: Output ratio (OR) measurements have been performed using standard and modified versions of the mD detector at nominal field sizes from 6 mm × 6 mm to 40 mm × 40 mm. In the first modified mD detector (mD_reversed), the type of charge carriers collected is reversed by connecting the opposite contact to the electrometer. In the second modified mD detector (mD_shortened), the detector's contacts have been shortened. The third modified mD detector (mD_noChip) is the same as the standard version but the diamond chip with the sensitive volume has been removed. Output correction factors were calculated from the measured OR and simulated using the EGSnrc package. An adapted Monte Carlo user-code has been used to study the underlying mechanisms of the field size-dependent charge imbalance and to identify the detector's structural components contributing to this effect.RESULTS: At the smallest field size investigated, the OR measured using the standard mD detector is >3% higher than the OR obtained using the modified mD detector with reversed contact (mD_reversed). Combining the results obtained with the different versions of the detector, the OR have been corrected for the effect of radiation imbalance. The OR obtained using the modified mD detector with shortened contacts (mD_shortened) agree with the corrected OR, all showing an over-response of less than 2% at the field sizes investigated. The discrepancy between the experimental and simulated output correction factors has been eliminated after accounting for the effect of charge imbalance.DISCUSSIONS AND CONCLUSIONS: The role of radiation-induced charge imbalance on the dose-response of mD detector in small field dosimetry has been studied and quantified. It has been demonstrated that the effect is significant at small field sizes. Multiple methods were used to quantify the effect of charge imbalance with good agreement between Monte Carlo simulations and experimental results obtained with modified detectors. When this correction is applied to the Monte Carlo data, the discrepancy from experimental data is eliminated. Based on the detailed component analysis using an adapted Monte Carlo user-code, it has been demonstrated that the effect of charge imbalance can be minimized by modifying the design of the detector's contacts.

radiology, nuclear medicine & medical imaging
The relationship of unsafe sexual behavior and the characteristics of sexual partners of HIV infected and HIV uninfected adolescent females.

M. Sturdevant,M. Belzer,G. Weissman,L. Friedman,M. Sarr,L. Muenz

DOI: https://doi.org/10.1016/S1054-139X(01)00286-5

IF: 7.898

2001-09-01

Journal of Adolescent Health

Abstract:
Investigation of interfractional range variation owing to anatomical changes with beam directions based on water equivalent thickness in proton therapy for pancreatic cancer

Yuhei Kikkawa,Hideaki Ueda,Yusuke Uchinami,Norio Katoh,Hidefumi Aoyama,Yoichi M Ito,Kohei Yokokawa,Ye Chen,Taeko Matsuura,Naoki Miyamoto,Seishin Takao

DOI: https://doi.org/10.1093/jrr/rrae069

2024-10-08

Abstract:To assess the interfractional anatomical range variations (ARVs) with beam directions and their impact on dose distribution in intensity modulated proton therapy, we analyzed water equivalent thickness (WET) from 10 patients with pancreatic cancer. The distributions of the interfractional WET difference ($\Delta{\mathrm{WET}}^{\theta }$) across 360° were visualized using polar histograms. Interfractional ARVs were evaluated using the mean absolute error and ΔWET pass rate, indicating the percentage of $\Delta \mathrm{WE}{\mathrm{T}}^{\theta }$ < thresholds. The impact on dose distribution in proton therapy was evaluated based on two treatment plans for 40 Gy(RBE)/5 fractions: 'Plan A', using two beam angles, in which the target was closest to the body surface among four perpendicular directions; and 'Plan B', using two beam angles with small ARVs. Analysis revealed individual variations in angular trends of interfractional ARVs. Three distinct trends were identified: Group 1 exhibited small ARVs around posterior directions; Group 2 exhibited small ARVs except ~60°; Group 3 demonstrated minimal ARVs only ~90°. In dose evaluation, while 150° and 210° were selected in Plan B for 9 out of 10 patients, for the remaining patient, 60° and 90° were chosen. Comparing dose volume histogram parameters for all patients, Plan B significantly reduced target coverage loss while maintaining organ-at-risk sparing comparable to Plan A. These results demonstrated that selecting beam angles with small interfractional ARVs for each patient enhances the robustness of dose distribution, reducing target coverage loss.
Defining field output factors in small fields based on dose area product measurements: A feasibility study

Julien Jurczak,Benjamin Rapp,Jean‐Marc Bordy,Stephanie Josset,Stephane Dufreneix

DOI: https://doi.org/10.1002/mp.16950

IF: 4.506

2024-01-26

Medical Physics

Abstract:Background Dose area product in water (DAPw) in small fields relies on the use of detectors with a sensitive area larger than the irradiation field. This quantity has recently been used to establish primary standards down to 5 mm field size, with an uncertainty smaller than 0.7%. It has the potential to decrease the uncertainty related to field output factors, but is not currently integrated into treatment planning systems. Purpose This study aimed to explore the feasibility of converting DAPw into a point dose in small fields by determining the volume averaging correction factor. By determining the field output factors, a comparison between the so‐called "DAPw to point dose" approach and the IAEA TRS483 methodology was performed. Method Diodes, microdiamonds, and a micro ionization chamber were used to measure field output factors following the IAEA TRS483 methodology on two similar linacs equipped with circular cones down to 6 mm diameter. For the "DAPw to point dose" approach, measurements were performed with a dedicated and built‐in‐house 3 cm diameter plane‐parallel ionization chamber calibrated in terms of DAPw in the French Primary Dosimetry Standards Laboratory LNE‐LNHB. Beam profile measurements were performed to generate volume averaging correction factors enabling the conversion of an integral DAPw measurement into a point dose and the determination of the field output factors. Both sets of field output factors were compared. Results According to the IAEA TRS483 methodology, field output factors were within ±3% for all detectors on both linacs. Large variations were observed for the volume averaging correction factors with a maximum spread between the detectors of 26% for the smallest field size. Consequently, deviations of up to 15% between the "IAEA TRS483" and the "DAPw to point dose" methodologies were found for the field output factor of the smallest field size. This was attributed to the difficulty in accurately determining beam profiles in small fields. Conclusion Although primary standards associated with small uncertainties can be established in terms of DAPw in a primary laboratory, the "DAPw to point dose" methodology requires volume averaging correction to derive a field output factor from DAPw measurements. None of the point detectors studied provided satisfactory results, and additional work using other detectors, such as film, is still required to allow the transfer of a DAP primary standard to users in terms of absorbed point dose.

radiology, nuclear medicine & medical imaging
Angular insensitivity of a gamma spectrometer for in-field applications

Harri Toivonen,Mark Dowdall

DOI: https://doi.org/10.1016/j.apradiso.2022.110561

Abstract:In-field measurements have particular challenges as compared with those conducted under laboratory conditions. Besides unknown source shielding, the source-detector distance varies and the detector orientation relative to the incident radiation is not necessarily constant. The incoming flux facing a detector is a parallel beam at long source-detector distances (>1 m). The counting efficiency depends on the tilting angle relative to the beam facing the detector. In principle, a cylindrical detector with a height-diameter ratio of π/4 (H/D = 0.785) exhibits the lowest angular dependency (41% at low energies for a tilting angle of 45° as compared with the orientation of the detector end cap relative to the beam). However, Monte Carlo simulations of a germanium detector showed that this variability can be greatly improved by slightly increasing H/D (0.84) and introducing a copper cladding around the detector (1.1 mm). The counting efficiency of such a detector is almost independent of the direction of photons arriving to the detector. The maximum deviation of 10% takes place at 200 keV.
Compact Light Source Performance in Recessed Type

Luminaires,E. Hammer

Abstract:Abslrncl Photometric comparisons were made with a n indoor, recessed, type luminaire using incandescent, high intensity discharge and compact fluorescent lamps. The test results show substantial performance advantages, as expected, for the discharge light sources where the efficacy gains can be in the order for 400% even when including the ballast losses associated with the discharge lamps. The candlepower distribution patterns emerging from these luminaries a re also different from those associated with the baseline incandescent lamps, arid which m-e in some ways, even more desirable from a uniformity of illuminance perspective. A section on fluorescent lamp starting is also included which describes a system having excellent starting characteristics in t e r m of electrode starting temperature (RH/RC technique), proper operating frequency to minimize unwanted IR interactions, and satisfactory current crest factor values to help irisure life performance.

The HLA linkage group.

Screening dental patients for temporomandibular disorders.

Influence of dose calculation algorithms on the helical diode array using volumetric‐modulated arc therapy for small targets

Small field output factor measurement and verification for CyberKnife robotic radiotherapy and radiosurgery system using 3D polymer gel, ionization chamber, diode, diamond and scintillator detectors, Gafchromic film and Monte Carlo simulation

Detector-specific correction factors in radiosurgery beams and their impact on dose distribution calculations

Comparison and Assessment of Profile and Output Factor Measurement for a Frameless Robotic Radiosurgery System Using Different Detectors

Accurate machine‐specific reference and small‐field dosimetry for a self‐shielded neuro‐radiosurgical system

Comparative Analysis of Four Detectors for the Profile Measurement Using CyberKnife

Impact of Measurement Conditions and Design Features of IBA Detectors on the Small Radiation Fields Output Factors

Quantification of Dosimetry Improvement With or Without Patient Surface Guidance

The relationship between fetal arterial oxygen saturation and heart and skeletal muscle myoglobin concentrations in the ovine fetus.

Angular correction methodology and characterization of a high-resolution CMOS array for patient specific quality assurance on a robotic arm linac

Technical Note: Investigating of dosimetric leaf gap and leaf transmission factor variations across gantry and collimator angles in volumetric modulation arc therapy

Monte Carlo simulation of beam characteristics from small fields based on TrueBeam flattening-filter-free mode

Computational and experimental small field dosimetry using a commercial plastic scintillator detector for the 0.35 T MR-linac

The role of radiation‐induced charge imbalance on the dose‐response of a commercial synthetic diamond detector in small field dosimetry

The relationship of unsafe sexual behavior and the characteristics of sexual partners of HIV infected and HIV uninfected adolescent females.

Investigation of interfractional range variation owing to anatomical changes with beam directions based on water equivalent thickness in proton therapy for pancreatic cancer

Defining field output factors in small fields based on dose area product measurements: A feasibility study

Angular insensitivity of a gamma spectrometer for in-field applications

Compact Light Source Performance in Recessed Type