Abstract:Corrosion is a massive disaster in many sectors that caused the loss of billions of dollars. For example, it was reported that the total direct estimated cost of corrosion was about $ 276 billion in 1998 in the US, which is 3.1% of the nation's GDP. Therefore, a necessity to develop methods to overcome this challenge arose in the last few decades. Thus, the development of corrosion resistive coatings is significantly attracted researchers' attention. In combination with the corrosion inhibitors, organic and conversion coatings are used to improve the corrosion resistance of high-strength Al alloys. However, many corrosion inhibitors are carcinogenic: Chromate conversion coating performed very well, but alternative options need to be explored due to restrictions on its applications due to the health and environmental regulations. Moreover, organic coatings provide good corrosion resistance, but poor wear resistance and mechanical damage lead to corrosion issues. Metallic coatings are an alternative, and galvanized steel is one of the prominent examples. However, metallic coatings produced by elements such as Cr, Ni, Ti, or Ta are noble for Al or Mg-based alloys. Therefore, in any event of coating breakdown, the substrate would be more active and act as an anode and, corrode rapidly by galvanic interaction. Thus, such metallic coatings produced by the above-mentioned corrosion resistance elements are not very attractive for Al alloys. We present a sacrificial metallic coating with outstanding corrosion resistance. Al was alloyed with V using high-energy ball milling (HEBM) which enabled the formation of a superstrated solid solution of V in Al. Al-V alloy powder produced by HEBM was used for coating the high-strength substrate using cold spray. The corrosion behavior and corrosion mechanisms of cold sprayed specimens were investigated using advanced electrochemical and analytical techniques. The cold sprayed specimens exhibit high pitting potential, low corrosion current density, and a less noble corrosion potential than the substrate. This indicates that in any event of coating breakdown, the coating would corrode (i.e., act as a sacrificial anode) and prevent the substrate from corrosion. Alloy composition is chosen such that corrosion of coating releases chemical species that could inhibit corrosion by decreasing the cathodic efficiency of the substrate.

Recovery of Al2O3 from hazardous Al waste as a reinforcement particle for high-performance Ni/Al2O3 corrosion resistance coating via ultrasonic-aided supercritical-CO2 electrodeposition

Grave-to-cradle upcycling of Ni from electroplating wastewater to photothermal CO 2 catalysis

Post-supercritical CO2 electrodeposition approach for Ni-Cu alloy fabrication: An innovative eco-friendly strategy for high-performance corrosion resistance with durability

Mechanical and Corrosion Resistance Enhancement of Closed-Cell Aluminum Foams through Nano-Electrodeposited Composite Coatings

Effect of Nanosized Silicon Dioxide Additive on Plasma Electrolytic Oxidation Coatings Fabricated on Aluminium

Sol–Gel-Derived Ni3Al Coating on Nickel Alloy for Oxidation Resistance in Supercritical Water Environments

Nano-TiO2 Coating Layers with Improved Anticorrosive Properties by Aerosol Flame Synthesis and Thermophoretic Deposition on Aluminium Surfaces

A novel strategy for recovery of heavy metals and synthesis of Co-rich alloy from the alkali-treated tungsten residue using photovoltaic silicon kerf waste

High-Temperature Corrosion of APS- and HVOF-Coated Nickel-Based Super Alloy under Air Oxidation and Melted Salt Domains

Hydrolysis‐induced Simultaneous Foaming and Coagulation Casting of Secondary Aluminum Dross Aqueous Suspension

Corrosion-Resistant Sacrificial Metallic Coatings Produced By Cold-Spray for Al Alloys

The Effect of Organic Matter from Sewage Sludge as an Interfacial Layer on the Surface of Nano-Al and Fluoride

Corrosion Behavior of ZnO-reinforced Coating on Aluminum Alloy Prepared by Plasma Electrolytic Oxidation

In‐situ Surface‐selective Removal of Al Element from NiFeAl Ternary Nanowires for Large‐current Oxygen Evolution Reaction

Oxidation protection dynamics of NiAl droplet by inflight in-situ carbon deoxidation during atmospheric plasma spraying for high performance NiAl coatings

Study of the Synergistic Influence of Plasma Electrolytic Oxidation and Wet Post-Treatment on the Surface of AA7075

Mechanism study of synergistic aluminum extraction and purification by ammonium for high-value conversion of secondary aluminum dross

Compound purification of nickel base superalloy cutting waste through special cleaning agent attached to ultrasonic stirring

Recovery and Regeneration of Al 2 O 3 with a High Specific Surface Area from Spent Hydrodesulfurization Catalyst CoMo/Al 2 O 3

Enhanced Cavitation Erosion–Corrosion Resistance of High-Velocity Oxy-Fuel-Sprayed Ni-Cr-Al2O3 Coatings Through Stationary Friction Processing

The Improvement in Corrosion Resistance of Electroless Ni-P Coating on Micro-arc Oxidized AZ31 Alloy Prepared with Sodium Dodecyl Sulfate Additive and Post-supercritical CO2 Mixed Electrolyte