Abstract:With an ever-expanding use of cross-sectional imaging for diagnostic and therapeutic purposes, there has also been an increase in the need for exposure to such radiological and anatomical views at the undergraduate and postgraduate level to allow for early familiarisation with the relevant anatomy. Cadaveric cross-sections offer an excellent link between the two-dimensional radiological images and the three-dimensional anatomical structures. For such cross-sections to be useful and informative within educational settings, they need to be: (i) safe for students and trainees to handle and (ii) robust enough to withstand repeated handling; as well as (iii) displaying anatomy clearly and accurately. There are various ways in which cross-sections can be prepared and presented; plastinated, potted, vacuum-sealed or unmounted. Each of these approaches has advantages and disadvantages in terms of technical complexity, cost and quality. As an alternative to the above methods and their limitations, we propose the presentation of cadaveric cross-sections in a transparent polyester resin. This technique has been used extensively in craft and artistic industries, yet it is not publicised in anatomy teaching settings. The sections were layered in polyester resin contained within a mould. The set resin required finishing by sanding and polishing. The final cross-sections were safe to handle, durable and maintained excellent anatomical relationships of the contained structures. The transparency of the set resin was water-clear and did not obstruct the visibility of the anatomy. The cost of the process was found to be significantly lower, requiring less infrastructure when compared with alternative methods. The following trivial technical difficulties were noted during the resin-embedding process: trapped air causing organs to float; retained water in the anatomical specimens creating bubbles and discoloration; and microbubbles emerging from the solution affecting the finished surface. However, solutions to these minor limitations have been discussed within the paper with the aim of future proofing this technique. The sections have been used in undergraduate medical teaching for 4 years and they have shown no signs of degradation or discoloration. We believe that this method is a viable and cost-effective alternative to other approaches of displaying cross-sectional cadaveric material and will help students and trainees bridge the gap between the traditional three-dimensional anatomy and two-dimensional images.

Vacuum-Sealed Hot Water Bath Immersion for the Preparation of Anatomical and Surgical Cadaveric Bone Models

History and future of human cadaver preservation for surgical training: from formalin to saturated salt solution method

Conditioned Canine Cadavers for Near-Natural Interprofessional Veterinary and Human Surgery Training

Effect of hot water maceration, rehydration, and soft tissue presence on 3D geometry of bone

Comparison of chemical and enzymatic maceration processes for soft tissue removal from arterial silicone casts on skull scaffolds

The production of anatomical teaching resources using three-dimensional (3D) printing technology

Take away body parts! An investigation into the use of 3D-printed anatomical models in undergraduate anatomy education

Workable Cadaveric Preservation for Developing Skills Training Models: A Review

Gross, organoleptic and histologic assessment of cadaveric equine heads preserved using chemical methods for veterinary surgical teaching

Swine viscera preservation in hypersaturated salt solution after alcohol fixation as a preparation method for educational purposes

A Modified Tape Transfer Approach for Rapidly Preparing High-Quality Cryosections of Undecalcified Adult Rodent Bones

A technique to perfuse cadavers that extends the useful life of fresh tissues: the Duke experience.

Developing a production workflow for 3D-printed temporal bone surgical simulators

The virtual dissecting room: Creating highly detailed anatomy models for educational purposes

Precision in Preservation: Mastering Cadaver Embalming with the Femoral Artery Approach - a technical note

Resin-embedded anatomical cross-sections as a teaching adjunct for medical curricula: is this technique an alternative to potting and plastination?

Animal Models Within Surgical Simulation: A Novel Approach to the 3 Rs

Exploring versatile applications of a vacuum-assisted bone harvester in orthopedic surgery

A new vessel filled and heart-beating human corpse model for VATS lobectomy training

Versatile and Tunable Performance of PVA/PAM Tridimensional Hydrogel Models for Tissues and Organs: Augmenting Realism in Advanced Surgical Training

Evaluation of polyethylene terephthalate glycol (PETG), Simubone™, and photopolymer resin as 3D printed temporal bone models for surgical simulation