Surgeon volume as a predictor of outcomes in inpatient and outpatient endocrine surgery.

A. Stavrakis,P. Ituarte,C. Ko,M. Yeh

DOI: https://doi.org/10.1016/J.SURG.2007.09.003

IF: 4.348

2007-12-01

Surgery

Abstract:

What problem does this paper attempt to address?

Overcoming Cellulose Recalcitrance in Woody Biomass for the Lignin-First Biorefinery.

Haibing Yang,Ximing Zhang,Hao Luo,Baoyuan Liu,Tânia M. Shiga,Xu Li,Jeong Im Kim,Peter Rubinelli,Jonathan C. Overton,Varun Subramanyam,Bruce R. Cooper,Huaping Mo,Mahdi M. Abu-Omar,Clint Chapple,Bryon S. Donohoe,Lee Makowski,Nathan S. Mosier,Maureen C. McCann,Nicholas C. Carpita,Richard Meilan

DOI: https://doi.org/10.1186/s13068-019-1503-y

2019-01-01

Biotechnology for Biofuels

Abstract:Low-temperature swelling of cotton linter cellulose and subsequent gelatinization in trifluoroacetic acid (TFA) greatly enhance rates of enzymatic digestion or maleic acid–AlCl3 catalyzed conversion to hydroxymethylfurfural (HMF) and levulinic acid (LA). However, lignin inhibits low-temperature swelling of TFA-treated intact wood particles from hybrid poplar (Populus tremula × P. alba) and results in greatly reduced yields of glucose or catalytic conversion compared to lignin-free cellulose. Previous studies have established that wood particles from transgenic lines of hybrid poplar with high syringyl (S) lignin content give greater glucose yields following enzymatic digestion. Low-temperature (− 20 °C) treatment of S-lignin-rich poplar wood particles in TFA slightly increased yields of glucose from enzymatic digestions and HMF and LA from maleic acid–AlCl3 catalysis. Subsequent gelatinization at 55 °C resulted in over 80% digestion of cellulose in only 3 to 6 h with high-S-lignin wood, compared to 20–60% digestion in the wild-type poplar hybrid and transgenic lines high in guaiacyl lignin or 5-hydroxy-G lignin. Disassembly of lignin in woody particles by Ni/C catalytic systems improved yields of glucose by enzymatic digestion or catalytic conversion to HMF and LA. Although lignin was completely removed by Ni/C-catalyzed delignification (CDL) treatment, recalcitrance to enzymatic digestion of cellulose from the high-S lines was reduced compared to other lignin variants. However, cellulose still exhibited considerable recalcitrance to complete enzymatic digestion or catalytic conversion after complete delignification. Low-temperature swelling of the CDL-treated wood particles in TFA resulted in nearly complete enzymatic hydrolysis, regardless of original lignin composition. Genetic modification of lignin composition can enhance the portfolio of aromatic products obtained from lignocellulosic biomass while promoting disassembly into biofuel and bioproduct substrates. CDL enhances rates of enzymatic digestion and chemical conversion, but cellulose remains intrinsically recalcitrant. Cold TFA is sufficient to overcome this recalcitrance after CDL treatment. Our results inform a ‘no carbon left behind’ strategy to convert total woody biomass into lignin, cellulose, and hemicellulose value streams for the future biorefinery.
Potential of Producing Carbon Fiber from Biorefinery Corn Stover Lignin with High Ash Content

Wangda Qu,Jing Liu,Yuan Xue,Xinwei Wang,Xianglan Bai

DOI: https://doi.org/10.1002/app.45736

IF: 3

2018-01-01

Journal of Applied Polymer Science

Abstract:ABSTRACTThe possibility of producing carbon fiber from an industrial corn stover lignin was investigated in the present study. As‐received, high‐ash containing lignin was subjected to methanol fractionation, acetylation, and thermal treatment prior to melt spinning and the changes in physiochemical and thermal properties were evaluated. Methanol fractionation removed most of the impurities in the raw lignin and also selectively removed the molecules with high melting points. However, neither methanol fractionation nor thermal treatment rendered melt‐spinnable precursors. The precursors were highly viscous and decomposed easily at low temperatures, attributed to the presence of H, G phenolic units, and abundant hydroxycinnamate groups in herbaceous lignin. A two‐step acetylation of methanol fractionated lignin greatly improved the mobility of lignin, while enhancing the thermal stability of the precursor during melt‐spinning. Fourier Transform Infrared and 2D‐NMR analysis showed that the contents of phenolic and aliphatic hydroxyls, as well as the hydroxycinnamates, decreased in the acetylated precursors. The optimum precursor was a partially acetylated lignin with a glass transition temperature of 85 °C. Upon oxidative stabilization and carbonization, the carbon fibers with an average tensile strength of 454 MPa and modulus of 62 GPa were obtained. The Raman spectroscopy showed the ID/IG ratio of the carbon fiber was 2.53. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 45736.
Sustainable preparation of lignocellulosic nanofibrils and cellulose nanopaper from poplar sawdust

Wei Liu,Shuya Zhang,Kun Liu,Hongbin Yang,Qingyi Lin,Ting Xu,Xueping Song,Haishun Du,Long Bai,Shuangquan Yao,Chuanling Si

DOI: https://doi.org/10.1016/j.jclepro.2022.135582

IF: 11.1

2022-12-18

Journal of Cleaner Production

Abstract:Lignocellulosic nanofibrils (LCNFs) are isolated from poplar sawdust via a sustainable preparation approach based on recyclable p-toluenesulfonic acid (p-TsOH) treatment and high-pressure homogenization. The obtained LCNFs show a network structure with a width of 15–30 nm and a length up to several micrometers. When hydrolysis duration is less than 60 min, the LCNFs exhibit high crystallinity (62.32%), good thermal stability ( Tmax = 367 °C), and fine dispersibility in water. Lignocellulose nanopapers (LCNP) are prepared using the LCNFs via simple vacuum filtration, which show superior mechanical performance and excellent UV-blocking function. The optimized LCNP presents high mechanical strength (up to 164.0 MPa) and toughness (up to 12.3 MJ/m 3 ), as well as good flexibility. We conclude that LCNF-derived LCNP can be finely adjusted by varying the residual lignin content, providing a rationale for LCNFs selection. This work offers a sustainable, optimized strategy for valorization and full utilization of low-value poplar sawdust into value-added LCNFs and LCNP.

environmental sciences,green & sustainable science & technology,engineering, environmental
The Role of Lignin Molecular Weight on Activated Carbon Pore Structure

Chengjun Wu,Junhuan Ding,Graham W. Tindall,Zachariah A. Pittman,Mark C. Thies,Mark E. Roberts

DOI: https://doi.org/10.3390/molecules29163879

IF: 4.6

2024-08-17

Molecules

Abstract:Over the past decade, the production of biofuels from lignocellulosic biomass has steadily increased to offset the use of fuels from petroleum. To make biofuels cost-competitive, however, it is necessary to add value to the "ligno-" components (up to 30% by mass) of the biomass. The properties of lignin, in terms of molecular weight (MW), chemical functionality, and mineral impurities often vary from biomass source and biorefinery process, resulting in a challenging precursor for product development. Activated carbon (AC) is a feasible target for the lignin-rich byproduct streams because it can be made from nearly any biomass, and it has a market capacity large enough to use much of the lignin generated from the biorefineries. However, it is not known how the variability in the lignin affects the key properties of AC, because, until now, they could not be well controlled. In this work, various fractions of ultraclean (<0.6% ash) lignin are created with refined MW distributions using Aqueous Lignin Purification using Hot Agents (ALPHA) and used as precursors for AC. AC is synthesized via zinc chloride activation and characterized for pore structure and adsorption capacity. We show that AC surface area and the adsorption capacity increase when using lignin with increasing MW, and, furthermore, that reducing the mineral content of lignin can significantly enhance the AC properties. The surface area of the AC from the highest MW lignin can reach ~1830 m2/g (absorption capacity). Furthermore, single step activation carbonization using zinc chloride allows for minimal carbon burn off (<30%), capturing most of the lignin carbon compared to traditional burn off methods in biorefineries for heat generation.

chemistry, multidisciplinary,biochemistry & molecular biology
Single-Solvent Fractionation and Electro-Spinning Neat Softwood Kraft Lignin

Bongkot Hararak,Inam Khan,Gerard F. Fernando

DOI: https://doi.org/10.1021/acsabm.3c00278

2023-07-31

ACS Applied Bio Materials

Abstract:This paper reports on the production of electro-spun nanofibers from softwood Kraft lignin without the need for polymer blending and/or chemical modification. Commercially available softwood Kraft lignin was fractionated using acetone. The acetone-soluble lignin (AcSL) had an ash content of 0.06 wt %, a weight average molecular weight of 4250 g·mol-1 along with the polydispersity index of 1.73. The corresponding values for as-received lignin (ARL) were 1.20 wt %, 6000 g·mol-1, and 2.22, respectively. The AcS was dissolved in a binary solvent consisting of acetone, and dimethyl sulfoxide (2:1, v/v) was selected for dissolving the AcSL. Conventional and custom-designed grounded electrode configurations were used to produce electro-spun neat lignin fibers that were randomly oriented or highly aligned, respectively. The diameter of the electro-spun fibers ranged from 1.12 to 1.46 μm. After vacuum drying at 140 °C for 6 h to remove the solvents and oxidation at 250 °C, the fibers were carbonized at 1000, 1200, and 1500 °C for 1 h. The carbonized fibers were unfused and void-free with an average diameter of 500 nm. Raman spectroscopy, scanning electron microscopy, and image analysis were used to characterize the carbonized fibers.
Effect of high residual lignin on the properties of cellulose nanofibrils/films

Yuan Chen,Dongbin Fan,Yanming Han,Shaoyi Lyu,Yun Lu,Gaiyun Li,Feng Jiang,Siqun Wang

DOI: https://doi.org/10.1007/s10570-018-2006-x

IF: 6.123

2018-01-01

Cellulose

Abstract:This work focused on an eco-friendly and facile method to produce lignocellulose nanofibrils (LCNFs) by the one-step grinding of original poplar wood. An array of detailed characterizations were performed to elucidate the effect of the residual lignin (22.1, 14.1, 8.2, 2.0, 0.4 and 0.2%) on the properties of LCNFs and its films. The LCNFs were rather sensitive to ultraviolet absorption, low-viscosity and anti-degradation properties. Morphological observations suggested that lignin particles homogeneously attach to the surface of cellulose nanofibrils for higher-residual-lignin samples. The results of chemical structures analysis demonstrated an effect of residual lignin amounts on the CrI. Further, the LCNF nanofilms exhibited enhanced hydrophobicity and mechanical properties. Overall, LCNFs are a renewable material with low environmental impact, low cost and they are being manufactured at a largescale. They also offer potential for a wide range of applications, such as ultraviolet protection, anti-degradation, and valuable reinforcing composite materials. Graphical Abstract
Lignin-based carbon fiber: a current overview

Felipe Souto,Veronica Calado,Nei Pereira

DOI: https://doi.org/10.1088/2053-1591/aaba00

IF: 2.025

2018-07-04

Materials Research Express

Abstract:Research involving lignin use is not new. For many years, the macromolecule was underestimated in its potential and burned for energy use in pulp and paper industries. However, with the advent of biorefinery on the valorization of lignocellulosic fractions, lignin is receiving greater motivation to be researched. Of the many applications, the most profitable one is its conversion into carbon fiber. Lignin-based carbon fibers can reduce the manufacturing price of this fiber to values greater than 35%, besides using a renewable material with a highly sustainable appellation. This paper gives an overview about lignin-based carbon fiber comparing the process to current precursors, presenting different pathways on different research, pointing to the most common difficulties and assessing new findings. A gap not fully clarified yet is concerning the lignin structure and its relation to extrusion process. After isolation procedures, lignin repolymerizes in a different manner compared to when it is in its natural form. Some studies have shown that some organic functions, the molecular weight and the structure conformation of the lignin can favor or disfavor thermal mobility. Although it is known purification is considered a criterion that favors extrusion, there is no study involving a selection of parameters that improves thermal mobility. Herein, it is highlighted a set of desired structure properties that provides a very good thermal mobility and extrusion in order to obtain a lignin-based carbon fiber with good properties.

materials science, multidisciplinary
Enzymatic Saccharification Promotion for Bioenergy Poplar under Green Liquor Pretreatment by Fully Sulfonated Polystyrene: Effect of Molecular Weight.

Tian Liu,Peipei Wang,Jing Tian,Jiaqi Guo,Wenyuan Zhu,Fazard Seidi,Yongcan Jin,Huining Xiao,Junlong Song

DOI: https://doi.org/10.1016/j.biortech.2022.127904

IF: 11.4

2022-01-01

Bioresource Technology

Abstract:Water-soluble lignin and lignin derivatives are cited to promote the enzymatic saccharification of lignocellulose. Herein, a series of fully sulfonated polystyrene sulfonates (FSPSSs) with various molecular weights (MW) were synthesized through free radical polymerization (FRP) and atom transfer radical polymerization (ATRP) to serve as lignin analogues to boost the enzymatic saccharification of bioenergy poplar under green liquor pretreatment. The FRP-made polymers with MW 944.5×103 to 123.6×103 g/mol increased the enzymatic hydrolysis digestibility (SED) by 13% to 18.8%. On contrary, the ATRP-made polymers with lower MW (3.8×103 ∼ 12.2×103 g/mol) showed a weak effect with less than 8% improvement in SED. This can be explained the adsorption capacity and the conformation of cellulase-FSPSS complexes, which respond to the reducing nonproductive adsorption correlated to their MWs, due to the strong dependence of molecular conformation on the chain length of strong polyelectrolytes.
Enabling high-quality carbon fiber through transforming lignin into an orientable and melt-spinnable polymer

Yixin Luo,Wangda Qu,Eric Cochran,Xianglan Bai

DOI: https://doi.org/10.1016/j.jclepro.2021.127252

IF: 11.1

2021-07-01

Journal of Cleaner Production

Abstract:Compared to carbon fibers made from conventional petroleum-based precursors, lignin-based carbon fibers can lower the production cost while enabling cleaner manufacturing. The use of lignin-based carbon fibers is currently hindered by their poor mechanical properties that are mainly attributed to the lack of orientability in lignin structure. Herein, we demonstrated a novel method of producing high-quality carbon fiber, by which lignin is first transformed into a new precursor polymer with a linear molecular orientation, and the precursor is subsequently melt-processed. Specifically, a raw red oak lignin bio-oil consisting of multifunctional compounds with distributed molecular weights was converted into a lightly branched, acrylate polymer via a hybrid functionalization followed by controlled radical polymerization. By carefully investigating different synthesis parameters and determining the effects of the intrinsic properties of the crude lignin bio-oil have on the polymerization, a melt-spinnable thermoplastic polymer could be obtained in high yield. The new polymer was then used to produce carbon fiber with average tensile strength of 1.70 GPa and tensile modulus of 182 GPa. Our analysis results indicated that the new precursor structure can improve the degree of graphitization and reduce structural defects in the resulting carbon fiber. Structural analyses showed that the carbon fiber contains a highly ordered and well-stacked turbostratic structure. Overall, this study presents a promising approach to produce low-cost, high-quality carbon fiber that may have applications in the automobile industries.

environmental sciences,green & sustainable science & technology,engineering, environmental
Preparation of Lignin-Based High-Ortho Thermoplastic Phenolic Resins and Fibers

Yu Ren,Jin Xie,Xiahong He,Rui Shi,Can Liu

DOI: https://doi.org/10.3390/molecules26133993

IF: 4.6

2021-06-30

Molecules

Abstract:Surplus lignin, which is inefficiently used, is generated in the forestry industry. Currently, most studies use lignin instead of phenol to synthesize thermosetting resins which cannot be reprocessed, thus affecting its application field. Thermoplastic phenolic resin has an orderly structure and excellent molding performance, which can greatly improve its application field and economic value. Herein, phenol was partially replaced with enzymolysis lignin (without treatment), generating lignin-based high-ortho thermoplastic phenolic resins (LPRs), and then lignin-based phenolic fibers (LPFs) were prepared by melt spinning. FTIR, 13C-NMR and GPC were used to characterize the ortho–para position ratio (O/P value), molecular weight and its distribution (PDI), and rheological properties of the resin. TG, XRD, SEM and tensile property studies were used to determine the thermal stability, orientation, and surface morphology of the fiber. Lignin addition resulted in the decline of the O/P value and molecular weight of the resin. For the 10% LPR, the O/P value, Mw, and PDI were 1.28, 4263, and 2.74, respectively, with the fiber exhibiting relatively good spinnability. The tensile strength and elongation at break of the 10% LPF were 160.9 MPa and 1.9%, respectively. The addition of lignin effectively improved the thermal properties of the fiber, and the carbon yields of 20% LPF before and after curing were 39.7% and 53.6%, respectively, which were 22.2% and 13.7% higher than that of the unmodified fiber, respectively.

chemistry, multidisciplinary,biochemistry & molecular biology
Fractionation of poplar through solid acid pretreatment assisted by mild alkali-1-butanol immersion to effectively produce xylose, glucose, and solid lignin

Yang Chen,Wei Qi,Usama Shakeel,Cuiyi Liang,Wen Wang,Yunzi Hu,Zhongming Wang,Zhenhong Yuan,Fei Shen,Qiong Wang

DOI: https://doi.org/10.1007/s13399-023-04378-4

IF: 4.05

2023-06-17

Biomass Conversion and Biorefinery

Abstract:The efficient fractionation and recovery of lignocellulosic biomass (LCB) constituents, hemicellulose, cellulose, and lignin, are ideal for LCB utilization. In this study, we prepared a solid acid catalyst (SPS120-40) with high acid density using polystyrene resin (PS) as precursor. The synthesized catalyst was characterized by XPS, 13 C NMR, TG-FTIR-MS, and so on to investigate its structural properties and thermal stability. During process optimization using FeCl 3 -assisted SPS120-40, a total of 78.9% xylose yield with 96.6% monosaccharide selectivity was achieved. Moreover, the catalyst showed extraordinary catalytic activity until five runs without significant loss in xylose yield. The pretreated residue was further treated with NaOH-1-butanol to effectively remove the lignin deposited on the residue surface and eventually 89.5% hydrolysis rate was obtained. At the same time, 64.4% lignin was obtained in the residue of enzymatic hydrolysis. This work provides important guidance for utilizing the whole components of lignocellulose.

energy & fuels,engineering, chemical
Conversion of control and genetically-modified poplar into multi-scale products using integrated pretreatments

Ling-Hua Xu,Cheng-Ye Ma,Peng-Fei Wang,Ying Xu,Xiao-Jun Shen,Jia-Long Wen,Tong-Qi Yuan

DOI: https://doi.org/10.1016/j.biortech.2023.129415

IF: 11.4

2023-06-01

Bioresource Technology

Abstract:In this work, a green and robust pretreatment which integrated acetic acid-catalyzed hydrothermal and wet mechanical pretreatment, was developed to efficiently produce high yield (up to 40.12%) of xylooligosaccharides and digestible substrates from Caffeoyl Shikimate Esterase down-regulated and control poplar wood. Subsequently, superhigh yield (more than 95%) of glucose and residual lignin were obtained after a moderate enzymatic hydrolysis. The residual lignin fraction exhibited a well-preserved β-O-4 linkages (42.06/100Ar) and high S/G ratio (6.42). Subsequently, lignin-derived porous carbon was successfully synthesized, and it exhibited a high specific capacitance of 273.8 F g-1 at 1.0 A g-1 and long cycling stability (remained 98.5% after 10,000 cycles at 5.0 A g-1) compared to control poplar wood, demonstrating that special advantage of this genetically-modified poplar in this integrated process. This work developed an energy-saving and eco-friendly pretreatment technology as a waste-free route for converting different lignocellulosic biomass to multiple products.

energy & fuels,biotechnology & applied microbiology,agricultural engineering
Physical and Chemical Properties of Acacia mangium Lignin Isolated from Pulp Mill Byproduct for Potential Application in Wood Composites

Nissa Nurfajrin Solihat,Eko Budi Santoso,Azizatul Karimah,Elvara Windra Madyaratri,Fahriya Puspita Sari,Faizatul Falah,Apri Heri Iswanto,Maya Ismayati,Muhammad Adly Rahandi Lubis,Widya Fatriasari,Petar Antov,Viktor Savov,Milada Gajtanska,Wasrin Syafii

DOI: https://doi.org/10.3390/polym14030491

IF: 5

2022-01-26

Polymers

Abstract:The efficient isolation process and understanding of lignin properties are essential to determine key features and insights for more effective lignin valorization as a renewable feedstock for the production of bio-based chemicals including wood adhesives. This study successfully used dilute acid precipitation to recover lignin from black liquor (BL) through a single-step and ethanol-fractionated-step, with a lignin recovery of ~35% and ~16%, respectively. The physical characteristics of lignin, i.e., its morphological structure, were evaluated by scanning electron microscopy (SEM). The chemical properties of the isolated lignin were characterized using comprehensive analytical techniques such as chemical composition, solubility test, morphological structure, Fourier-transform infrared spectroscopy (FTIR), 1H and 13C Nuclear Magnetic Resonance (NMR), elucidation structure by pyrolysis-gas chromatography-mass spectroscopy (Py-GCMS), and gel permeation chromatography (GPC). The fingerprint analysis by FTIR detected the unique peaks corresponding to lignin, such as C=C and C-O in aromatic rings, but no significant differences in the fingerprint result between both lignin. The 1H and 13C NMR showed unique signals related to functional groups in lignin molecules such as methoxy, aromatic protons, aldehyde, and carboxylic acid. The lower insoluble acid content of lignin derived from fractionated-step (69.94%) than single-step (77.45%) correlated to lignin yield, total phenolic content, solubility, thermal stability, and molecular distribution. It contradicted the syringyl/guaiacyl (S/G) units’ ratio where ethanol fractionation slightly increased syringyl unit content, increasing the S/G ratio. Hence, the fractionation step affected more rupture and pores on the lignin morphological surface than the ethanol-fractionated step. The interrelationships between these chemical and physicochemical as well as different isolation methods were investigated. The results obtained could enhance the wider industrial application of lignin in manufacturing wood-based composites with improved properties and lower environmental impact.

polymer science
Upscaling of lignin precursor melt spinning by bicomponent spinning and its use for carbon fibre production

Lars Bostan,Omid Hosseinaei,Renate Fourn,Axel S. Herrmann,Renate Fourné

DOI: https://doi.org/10.1098/rsta.2020.0334

2021-09-13

Abstract:Upscaling lignin-based precursor fibre production is an essential step in developing bio-based carbon fibre from renewable feedstock. The main challenge in upscaling of lignin fibre production by melt spinning is its melt behaviour and rheological properties, which differ from common synthetic polymers used in melt spinning. Here, a new approach in melt spinning of lignin, using a spin carrier system for producing bicomponent fibres, has been introduced. An ethanol extracted lignin fraction from LignoBoost process of commercial softwood kraft black liquor was used as feedstock. After additional heat treatment, melt spinning was performed in a pilot-scale spinning unit. For the first time, biodegradable polyvinyl alcohol (PVA) was used as a spin carrier to enable the spinning of lignin by improving the required melt strength. PVA-sheath/lignin-core bicomponent fibres were manufactured. Afterwards, PVA was dissolved by washing with water. Pure lignin fibres were stabilized and carbonized, and tensile properties were measured. The measured properties, tensile modulus of 81.1 ± 3.1 GPa and tensile strength of 1039 ± 197 MPa, are higher than the majority of lignin-based carbon fibres reported in the literature. This new approach can significantly improve the melt spinning of lignin and solve problems related to poor spinnability of lignin and results in the production of high-quality lignin-based carbon fibres. This article is part of the theme issue ‘Bio-derived and bioinspired sustainable advanced materials for emerging technologies (part 2)’.
Lignin/Poly(vinylpyrrolidone) Multifilament Fibers Dry‐Spun from Water as Carbon Fiber Precursors

Philipp Kreis,Erik Frank,Bernd Clauß,Volker Bauch,Heiko Stolpmann,Lisa Kuske,Tanja Schneck,Simon König,Michael R. Buchmeiser

DOI: https://doi.org/10.1002/mame.202300296

2023-10-18

Macromolecular Materials and Engineering

Abstract:This study demonstrates the successful production of lignin‐based carbon fibers. For this purpose, lignin fibers are spun by dry spinning from aqueous solution followed by stabilization and continuous carbonization to endless yarns. This represents a completely new and environmentally friendly approach, since the process does not require the use of solvents or toxic additives. The preparation of lignin‐based carbon fibers by dry spinning from aqueous solution followed by stabilization and continuous carbonization to endless yarns is reported. The influence of carbonization temperature and draw ratio on the morphology and mechanical properties of the final carbon fibers is investigated by single‐fiber testing, wide‐angle X‐ray scattering, scanning electron microscopy, and Raman spectroscopy. A draw ratio of 5% (1.05) with a carbonization temperature of 1400 °C leads to the best mechanical properties. The resulting multifilament carbon fibers have an average diameter between 10–12 μm, an average tensile strength of 1.30 ± 0.32 GPa, a Young's modulus of 101 ± 18 GPa, and an elongation at break of 1.31 ± 0.23%. The maximum Weibull strength (σ0) is 1.04 GPa with a Weibull modulus (m) of 5.1. The use of a water‐soluble system is economically advantageous; also, unlike melt‐spun lignin fibers, the dry‐spun precursor fibers can be thermally converted without any additional crosslinking step.

materials science, multidisciplinary,polymer science
Ultrafine grinding of poplar biomass: effect of particle morphology on the liquefaction of biomass for methyl glycosides and phenolics

Qiaolong Zhai,Fanglin Li,Fei Wang,Junfeng Feng,Jianchun Jiang,Junming Xu

DOI: https://doi.org/10.1007/s10570-019-02332-0

IF: 6.123

2019-03-02

Cellulose

Abstract:This paper shows that mechanical ultrafine grinding of poplar wood is an efficient pretreatment approach to enhance its reactivity during liquefaction. The microstructural features and chemical properties of biomass samples with different particle morphology were studied. In particular, we found that more cellulose and hemicellulose were exposed on the outer surface of the ultrafine powder (cellular scale of plant) and the crystal lattice structure of cellulose was significantly damaged. As a result, the degree of liquefaction reached 92.03% at 180 °C using UP feedstock, largely exceeding the value (53.35%) obtained at the same temperature using PS0.25. Two groups of value-added chemicals, namely phenolics and methyl glycosides were obtained during liquefaction. At 180 °C, the yields of methyl glycosides and phenolics obtained from an UP feedstock were, respectively, 28.45% and 10.17% higher than those obtained from the PS0.25. In addition, a high degree of liquefaction (> 90%) could be obtained at a temperature 40 °C lower than the one required by PS0.25, greatly reducing the occurrence of side reactions and improving the purity of target products. Overall, the mechanical fragmentation of biomass at cellular scale is a promising pretreatment method allowing high valorization of the entire biomass.Graphical abstract

materials science, textiles,polymer science, paper & wood
Enhancing Carbon Fiber Properties through Lignin-Cellulose Composites: A Comparative Study of Hardwood Vs. Softwood Lignin Sources

Azega Rajaras,Jenny Bengtsson,Hans Theliander,Per Lundgren

DOI: https://doi.org/10.1149/ma2023-0283420mtgabs

2023-12-22

ECS Meeting Abstracts

Abstract:Carbon fibers are integral to a wide range of applications, including automotive, construction, packaging, textiles, and emerging fields such as energy storage electrodes like flexible supercapacitors. However, concerns related to limited availability and environmental impact associated with fossil-based carbon fiber production have sparked growing interest in sustainable alternatives, particularly those derived from lignin and cellulose composites. This conference work presents a comparative analysis of the mechanical properties of lignin-cellulose composite carbon fibers derived from hardwood and softwood lignin sources, elucidating the significant influence of lignin origin on fiber performance. Our study focuses on the advantages and disadvantages of utilizing a composite of hardwood lignin vs. softwood lignin with cellulose in carbon fiber production, comparing these materials to commercially available carbon fibers. We emphasize the mechanical performance of these composite fibers, specifically highlighting the tensile strength and tensile modulus as a key metric. Notably, our results demonstrate that carbon fibers derived from hardwood lignin/cellulose composites exhibit superior mechanical strength compared to those from softwood lignin/cellulose composites. To gain fundamental insights into the reasons behind this mechanical disparity, we employed Raman spectroscopy to analyze the carbon structures within the fibers. Our findings revealed that carbon fibers produced from hardwood lignin exhibited a higher degree of graphitization, helping in achieving of typically desirable pre-graphite turbostractic carbon structures. These structural enhancements significantly contributed to the improved mechanical characteristics observed. In summary, our research underscores the critical importance of lignin source selection in the production of lignin-cellulose composite carbon fibers. The mechanical performance of these fibers is closely linked to the carbon morphology influenced by the lignin source. Therefore, understanding and controlling the lignin source from hardwood or softwood is pivotal for tailoring carbon fiber properties to meet specific application requirements. This study not only advances the knowledge in sustainable carbon fiber production but also offers valuable insights into achieving desirable properties for a wide range of applications, including advanced energy storage systems and structural materials.
Mechanical Strength, Thermal Stability, and Hydrophobicity of Fiber Materials after Removal of Residual Lignin

Quanliang Wang,Shengling Xiao,Sheldon Q. Shi,Liping Cai

DOI: https://doi.org/10.15376/biores.13.1.71-85

2017-11-03

BioResources

Abstract:The behaviors of the mechanical, hydrophobic, and thermal properties of the molded fiber product (MFP) were examined after the removal of residual lignin. The fibers resulting from the chemi-thermomechanical pulping and bleaching processes were treated by extended delignification, namely by their reaction with glacial acetic acid and sodium chlorite. The changes in surface composition, chemical structure, crystallinity, microstructure, and thermal stability of the MFP were investigated by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA), respectively. Results showed that the composition and structure of carbohydrates on the fiber surface were not changed significantly, the lignin in fibers was almost completely removed, the relative content of intermolecular hydrogen bonds in cellulose and the contact area between fibers was increased, and the crystallinity index increased from 79.5% to 81.4% after the extended delignification. When the content of lignin decreased from 5.78% to 0.02%, the tensile strength of the MFP increased 25.6%, but little changes were found in the bending strength. The onset thermal decomposition temperature of MFP increased from 242 °C to 250 °C and the maximum rate of degradation temperature increased from 347 °C to 350 °C.

materials science, paper & wood
Aqueous ethanol fractionation of softwood and hardwood kraft lignins: Impact on purity and properties

Daniel Beaudoin,Sophie Langis-Barsetti,Alain Gagné,Ernest Palus,John Inwood,Mohan K. R. Konduri,Daniel BeaudoinSophie Langis-BarsettiAlain GagnéErnest PalusJohn InwoodMohan K. R. Konduria FPInnovations,Bioproducts Centre of Excellence,Pointe-Claire,Québec,Canadab FPInnovations,Bio-Economy Centre,Thunder Bay,Ontario,Canada

DOI: https://doi.org/10.1080/02773813.2024.2314454

2024-02-18

Journal of Wood Chemistry and Technology

Abstract:Industrial kraft lignins are mixtures of macromolecular components variable in both structure and composition. To maximize their value in commercial applications, they often need to be homogenized and purified. Several fractionation methods have been reported to improve the properties of kraft lignins, but these reports have been mostly limited to kraft lignins of single origins. In this study, the physicochemical properties of fractions from four industrial kraft lignins were compared. Fractionation was performed on both softwood and hardwood lignins by partial dissolution in aqueous ethanol followed by precipitation with water. The yields of each fraction varied greatly between the lignins, with differences reaching up to 35% for a single fraction. All fractions were characterized which showed that fractions having remarkably similar properties and compositions can be obtained from different lignins. Organic and inorganic impurities were found to concentrate in specific fractions which allowed the isolation of highly purified fractions of kraft lignin. These results highlight the importance of matching individual kraft lignins with suitable applications.

materials science, paper & wood

Surgeon volume as a predictor of outcomes in inpatient and outpatient endocrine surgery.

Overcoming Cellulose Recalcitrance in Woody Biomass for the Lignin-First Biorefinery.

Potential of Producing Carbon Fiber from Biorefinery Corn Stover Lignin with High Ash Content

Sustainable preparation of lignocellulosic nanofibrils and cellulose nanopaper from poplar sawdust

The Role of Lignin Molecular Weight on Activated Carbon Pore Structure

Single-Solvent Fractionation and Electro-Spinning Neat Softwood Kraft Lignin

Effect of high residual lignin on the properties of cellulose nanofibrils/films

Lignin-based carbon fiber: a current overview

Enzymatic Saccharification Promotion for Bioenergy Poplar under Green Liquor Pretreatment by Fully Sulfonated Polystyrene: Effect of Molecular Weight.

Enabling high-quality carbon fiber through transforming lignin into an orientable and melt-spinnable polymer

Preparation of Lignin-Based High-Ortho Thermoplastic Phenolic Resins and Fibers

Fractionation of poplar through solid acid pretreatment assisted by mild alkali-1-butanol immersion to effectively produce xylose, glucose, and solid lignin

Conversion of control and genetically-modified poplar into multi-scale products using integrated pretreatments

Physical and Chemical Properties of Acacia mangium Lignin Isolated from Pulp Mill Byproduct for Potential Application in Wood Composites

Upscaling of lignin precursor melt spinning by bicomponent spinning and its use for carbon fibre production

Lignin/Poly(vinylpyrrolidone) Multifilament Fibers Dry‐Spun from Water as Carbon Fiber Precursors

Ultrafine grinding of poplar biomass: effect of particle morphology on the liquefaction of biomass for methyl glycosides and phenolics

Enhancing Carbon Fiber Properties through Lignin-Cellulose Composites: A Comparative Study of Hardwood Vs. Softwood Lignin Sources

Mechanical Strength, Thermal Stability, and Hydrophobicity of Fiber Materials after Removal of Residual Lignin

Aqueous ethanol fractionation of softwood and hardwood kraft lignins: Impact on purity and properties