Abstract:PURPOSE Localized cortical cataracts in the human lens have been shown to involve a selective increase in calcium with no change in sodium content. Recent studies in the rat lens in vitro have shown that the store-operated channel is highly selective for calcium over sodium, and therefore this channel was characterized further in human lens cells. METHODS Human primary cultures were initiated from epithelial explants and passaged onto coverslips. After incorporating Fura-2, agonist- or thapsigargin-induced changes in cytosolic calcium were monitored and calibrated using fluorometric digital imaging techniques. RESULTS Histamine and adenosine triphosphate (ATP; 10 microM) induced a large transient increase in cytosolic calcium followed by a maintained lower plateau phase in the continued presence of the calcium-signaling agonist. The second phase was abolished by removing external calcium and represented the contribution from the store-operated influx. The store-operated pathway was blocked by inorganic agents such as zinc and nickel (100 microM) but was insensitive to the voltage-sensitive calcium channel blocker, nifedipine (1 mM). Depolarizing the membrane voltage by raising the external potassium (75 mM) also blocked the influx. Similar results were obtained if the store was first emptied directly using thapsigargin (1 microM), and with this agent it was also possible to observe the very slow activation and inactivation kinetics (>10 seconds) of the channel. Addition of manganese to the bathing medium initiated a quench of Fura-2 isobestic fluorescence that was enhanced 2.9 +/- 0.3-fold after 10 microM ATP addition. There was a delay of 82 +/- 16 seconds between initiation of the calcium spike and the Mn2+ quench rate, indicating the presence of a delayed entry pathway. In the resting state, removal of, or increasing extracellular calcium concentration 10-fold did not perturb the level of cytosolic Ca2+. Similar maneuvers performed after agonist- or thapsigargin-induced store depletion of intracellular stores brought about dramatic changes in cytosolic Ca2+ consistent with the activation of a Ca2+ entry pathway. Lower concentrations of agonist induced oscillations of Ca2+ that continued for a short time in Ca-free solution. No increase in Mn2+ quench rate was associated with oscillations. A 100-microM zinc- and KCl-induced blockade of Ca2+ entry had no effect on the form of agonist-induced oscillations. Inhibition of Ca2+ influx by zinc (100 microM) converted a sustained Ca2+ response to a train of repetitive Ca2+ spikes. CONCLUSIONS Human lens cells normally have very low Ca2+ permeability. Depletion of intracellular stores by agonists or thapsigargin initiates a Ca2+ entry pathway that is not required for the Ca2+ oscillations induced by low concentrations of agonist. This potentially provides a signal transduction mechanism with minimal risk of Ca2+ overload to the lens, whereas overactivation of the store-operated channel is a possible way of increasing calcium in the lens and could explain the distribution found in localized cataracts.

Role of the endoplasmic reticulum in shaping calcium dynamics in human lens cells.

Thermal Shock Behavior of Twill Woven Carbon Fiber Reinforced Polymer Composites

On the mechanical behavior of carbon fiber/epoxy laminates exposed in thermal cycling environments

Thermomechanical Behavior and Microstructure Properties of Carbon Fiber Reinforced Polymer at Elevated Temperatures

Characterization of the thermal and mechanical properties of additively manufactured carbon fiber reinforced polymer exposed to above-zero and sub-zero temperatures

The effect of thermal cycles on the mechanical properties of fiber–metal laminates

High-Temperature Effect on the Tensile Mechanical Properties of Unidirectional Carbon Fiber-Reinforced Polymer Plates

Effects of Thermal Cycling on Damage Progress in Interlaminar-Toughened CFRP Cross-Ply Laminates

Effects of Heat-Treatment on Tensile Behavior and Dimension Stability of 3D Printed Carbon Fiber Reinforced Composites

Effect of Thermal Shock Conditions on the Low-Cycle Fatigue Performance of 3D-Printed Materials: Acrylonitrile Butadiene Styrene, Acrylonitrile-Styrene-Acrylate, High-Impact Polystyrene, and Poly(lactic acid)

Coronary Sinus Interventions: From Concept to Clinics

Experimental and multiscale modeling investigations of cryo-thermal cycling effects on the mechanical behaviors of carbon fiber reinforced epoxy composites

Internal shear damage evolution of CFRP laminates ranging from -100°C to 100°C using in-situ X-ray computed tomography

The Effects of Curing Process on the Damage Behavior of Additively Manufactured Fiber-Reinforced Thermosetting Composites

Characterization on fatigue behavior and damage mechanism of C/BMI composites experienced thermal cycling

Thermal, Tensile and Fatigue Behaviors of the PA6, Short Carbon Fiber-Reinforced PA6, and Continuous Glass Fiber-Reinforced PA6 Materials in Fused Filament Fabrication (FFF)

Effect and mechanism of thermal aging on mechanical properties of continuous carbon fiber‐reinforced PEEK composite laminates

Effect of temperature and moisture composite environments on the mechanical properties and mechanisms of woven carbon fiber composites

Influence of Long-Term Moisture Exposure and Temperature on the Mechanical Properties of Hybrid FRP Composite Specimens

Effect of high temperature on FRCM‐confined concrete

Effect of Thermal Ageing on the Impact Damage Resistance and Tolerance of Carbon-Fibre-Reinforced Epoxy Laminates