Hemodynamics and gas exchange during carbon dioxide insufflation for totally endoscopic coronary artery bypass grafting.

Christian Byhahn,S. Mierdl,D. Meininger,G. Wimmer‐Greinecker,G. Matheis,K. Westphal

DOI: https://doi.org/10.1016/S0003-4975(01)02428-6

2001-05-01

Abstract:

What problem does this paper attempt to address?

Robust I&I Adaptive Dsc With Disturbance Observer For Maglev System With Output Constraint

Jiaqi Liu,Xiangbin Liu,Hongye Su

DOI: https://doi.org/10.23919/CCC50068.2020.9189084

2020-01-01

Abstract:This paper proposes a robust immersion and invariance (I&I) adaptive dynamic surface controller (DSC) with disturbance observer (DO) for the tracking control of uncertain output-constrained maglev system subjected to mismatched disturbance. The uncertain maglev system with output constraint is firstly transformed into an equivalent unconstrained one via a constructive nonlinear mapping. Dynamic surface control (DSC) combined with I&I adaption law and extended disturbance observer is designed systematically for the transformed system. The proposed control law overcomes the problem of "explosion of complexity" due to the DSC baseline controller. The robust I&I adaptation law in the control law is developed to recover the unknown parameter of the system, which shapes the dynamics of parameter estimation error and renders the estimation error exponentially converging to a bounded residual set. And the extended disturbance observer is used to handle the time-varying mismatched disturbances in the maglev system. The stability analysis of the overall system shows that all signals of the closed-loop system are bounded and output constraint of the system is not violated as well. The numerical simulation results verify the effectiveness of the proposed controller at last.
Robust Immersion and Invariance Adaptive Coordinated Control for a Class of Biaxial Gantry Systems

Kangjun Wang,Xiangbin Liu,Hongye Su

DOI: https://doi.org/10.1080/23307706.2021.1966325

2021-01-01

Journal of Control and Decision

Abstract:This paper proposes a robust Immersion and Invariance (I&I) adaptive coordinated controller for a class of uncertain linear-motor-driven biaxial gantry system subject to external disturbances for high-accuracy contour tracking. Firstly, the dynamic model of the gantry system is transformed into task coordinate frame, through which the contour tracking can be regarded as a regulation problem. Based on the transformed system dynamics, an I&I-based adaptation law with smooth projection is proposed to estimate the unknown parameters. Different from traditional adaptive control, the proposed robust I&I adaptive control introduces a new term called tuning function in adaptation law to shape the dynamic behaviour of the estimation vector. Then the stability of the closed-loop system is proved by Lyapunov theory. Finally, comparative experiments are executed on an industrial biaxial gantry system with two different cases to verify the effectiveness of the proposed control law.
A novel non-singular terminal sliding mode control-based integrated missile guidance and control with impact angle constraint

Chao Ming,Xiaoming Wang,Ruisheng Sun

DOI: https://doi.org/10.1016/j.ast.2019.105368

IF: 5.457

2019-11-01

Aerospace Science and Technology

Abstract:A novel impact angle constrained integrated guidance and control (IGC) scheme is proposed with non-singular terminal sliding mode control (NTSMC) technique for missile to intercept a maneuverable target. Firstly, an IGC design model is innovatively established in a strict feedback form which selects the normal overload as the system state in replace of the angle of attack so that the system states both are measurable. On this basis, an IGC law is proposed to guarantee the impact angle converge to the expected command within a finite time and to improve the robustness against the multiple disturbances which include the model parameter uncertainties and the target maneuvering by incorporating the NTSMC method and the extended state observer (ESO) technique. In order to avoid the chattering phenomenon, the smooth derivative of the intermediate control command which is obtained by the introduced nonlinear tracking differentiator (TD) is adopted into the control loop. Then, the stability of closed-loop integrated system is rigorously proved by utilizing the Lyapunov theorem. Finally, extensive contrast simulation results are presented to validate the efficiency, superiority and robustness of the suggested IGC scheme.

engineering, aerospace
Integrated Missile Guidance And Control Design With Smooth Adaptive Sliding Mode Control

zhou jialing,yang jianying

DOI: https://doi.org/10.1109/chicc.2015.7260451

2015-01-01

Abstract:This paper considers the problem of a missile intercepting a maneuvering target with demand for fast finite-time convergence and anti-chattering. Based on the widely used proportional navigation strategy, a novel integrated guidance and control (IGC) scheme is proposed, which is formulated as a second-order affine nonlinear system with uncertainties. Then the smooth adaptive nonsingular terminal sliding mode control (SANTSMC) method which is proposed in our pervious work is applied to this IGC scheme. By virtue of the SANTSMC method, the uncertainties with unknown bounds can be addressed, fast finite-time convergence can be achieved, and the chattering problem can be well solved.
Impact angle-constrained integrated guidance and control for supersonic skid-to-turn missiles using backstepping with global fast terminal sliding mode control

Zhibing Li,Quanlin Dong,Xiaoyue Zhang,Yuanfei Gao

DOI: https://doi.org/10.1016/j.ast.2022.107386

IF: 5.457

2022-03-01

Aerospace Science and Technology

Abstract:An integrated guidance and control (IGC) scheme based on global terminal sliding mode control (GTSMC), backstepping control (BC), linear feedback (LF), dynamic surface control (DSC), reduced-order extended state observer (ESO) for a supersonic skid-to-turn (STT) interceptor intercepting maneuvering targets is presented. The IGC scheme considers the delay dynamics of the rudder and solves the impact angle constraint. First, a fifth-order strict-feedback nonlinear IGC model with mismatched uncertainties was established taking into account the rudder delay dynamics. Second, the guidance and control system based on BC consists of the guidance subsystem, normal overload subsystem, attitude subsystem, rudder subsystem. Each subsystem was designed based on the GTSMC and LF. In particular, the GTSMC was designed for the guidance subsystem to ensure the fast convergence of the line-of-sight angle. The DSC was introduced to calculate virtual commands to prevent “differential explosion”. The unknown lumped disturbances, including target maneuvers, external disturbances, and perturbations caused by the aerodynamic parameters, were accurately estimated and compensated for by the reduced-order ESO in the proposed IGC scheme. The closed-loop system was proved to be stable and the system states to be uniformly bounded using Lyapunov theory. Finally, simulation results demonstrated the superiority of the proposed IGC scheme compared to previously proposed schemes.

engineering, aerospace
Dasherkandi project studies. Demography, morbidity and mortality in a rural community of Bangladesh.

A. Chowdhury,M. Alam,S. M. Ali

Bangladesh Medical Research Council Bulletin

Abstract:The entire population of Dasherkandi, a village near Dacca city was surveyed. Out of 1181 people 44.2% suffered from organic or psychiatric disorders. 37.7% suffered from physical disorders, 3.6% suffered from psychiatric disorders and another 2.9% suffered from both psychiatric and physical disorders. The common physical disorders were worm infestations, hypertension, peptic ulcer, dental problems and upper respiratory tract infection including flu. Females suffered from psychiatric diseases more than males. The psychiatric morbidity found in the survey differed significantly from those found in other similar surveys. Depressive states were the commonest psychiatric disorder and women suffered four times as frequently as men. Anxiety neurosis was the next common psychiatric problem. Both crude mortality and infant mortality rates (5.75 and 93.20 per thousand respectively) were lower than those of other similar studies. The commonest cause of infant mortality during first one month of life was tetanus in this series. Inspite of the fact that diagnosis was based entirely on clinical findings the morbidity rate was high. It was observed that a high percentage of the people who suffered from psychiatric disorders were due to problems which can be easily tackled under field conditions.
Integrated guidance and control design by active disturbance rejection method for high-velocity target interceptor with DCS thruster

Ali Chitsaz,Abolghasem Naghash,Farhad Fani Saberi

DOI: https://doi.org/10.1038/s41598-024-52008-4

IF: 4.6

2024-01-16

Scientific Reports

Abstract:The present paper proposes a novel integrated guidance and control (IGC) method for engaging with high-speed targets such as ballistic projectiles. considering an extreme short period of terminal engagement due to high relative velocity between target and interceptor, it is particularly important for IGC law to show desirable performance in the presence of various uncertainties (e.g. variation in aerodynamic coefficients) and disturbances (e.g. target maneuver and drag). This article extends the ICG law for mismatched and feedback form equations based on the Active Disturbance Rejection Control (ADRC) method using the back-stepping technique and the Reduced-order Extended State Observer (RESO). The primary consideration is the application of thrusters on the center of mass as the Divert Control System (DCS), along with the daisy-chain technique for control allocation between the fins and thruster commands. Contrary to previous research, the filter and angle measurement error are modeled for the seeker as a crucial parameter to highlight the significance of the thruster. The simulation results indicate the efficiency of the developed method for near-miss or hit-to-kill engagement with tactical ballistic targets. It is shown that the thruster plays a significant role in high-altitude engagements, specifically in the presence of non-ideal seeker. Finally, using the Monte Carlo simulation, it is proved that adding inner loops to the developed technique will not remove the IGC's advantage over the conventional approach and Non-singular Terminal Sliding Mode (NTSM) guidance law.

multidisciplinary sciences
Integrated Guidance and Control Method for the Interception of Maneuvering Hypersonic Vehicle Based on High Order Sliding Mode Approach

Kang Chen,Bin Fu,Yuening Ding,Jie Yan

DOI: https://doi.org/10.1155/2015/648231

IF: 1.43

2015-01-01

Mathematical Problems in Engineering

Abstract:This paper focuses on the integrated guidance and control (IGC) method applied in the interception of maneuvering near space hypersonic vehicles using the homogeneous high order sliding mode (HOSM) approach. The IGC model is derived by combining the target-missile relative motion and dynamic equations. Then, a fourth-order sliding mode controller is implemented in the augmented IGC model. To estimate the high order derivatives of the sliding manifold which is required in the HOSM method, an Arbitrary Order Robust Exact Differentiator is presented. At last, the idea of virtual control is introduced to alleviate the chattering of the control input without using any saturation functions which may lead to a loss of the robustness. And the stability of the closed-loop system with presented fourth-order homogeneous HOSM controller is also proved theoretically. Finally, simulation results are provided and analyzed to demonstrate the effectiveness of the proposed method in three typical engagement scenarios.

engineering, multidisciplinary,mathematics, interdisciplinary applications
Multiple‐missile fixed‐time integrated guidance and control design with multi‐stage interconnected observers under impact angle and input saturation constraints

Dingye Zhang,Hang Yu,Keren Dai,Wenjun Yi,He Zhang,Zhiming Lei

DOI: https://doi.org/10.1049/cth2.12658

IF: 2.67

2024-04-13

IET Control Theory and Applications

Abstract:There are three main points: the first one is to add the actuator factors to the existing multiple‐missile cooperative guidance law to consider the design of an integrated guidance and control scheme under multiple‐missile cooperative guidance; the second one is to design the disturbance observer with the ability to influence and sense each other on the basis of the existing fixed‐time disturbance observer based on the improved super‐twisting algorithm; and the third one is to derive the limits of a maneuvering target's acceleration perpendicular to the LOS direction under input saturation constraints. In this paper, a novel three‐dimensional fixed‐time integrated guidance and control (IGC) scheme with multi‐stage interconnected observers is proposed for cooperative attacks using multiple missiles against a maneuvering target under impact angle and input saturation constraints. External disturbances, modeling errors, and aerodynamic parameter variations are considered as system uncertainties and a three‐channel fully coupled IGC model for multiple missiles is established. The IGC system is designed optimally based on fixed‐time stability theory, sliding mode control, and the backstepping technique. Three inter‐cascaded fixed‐time disturbance observers based on an improved super‐twisting algorithm are designed to estimate and compensate for system uncertainties. Second‐order command filters are used to constrain virtual control signals, and additional filtering error subsystems are introduced to compensate for the tracking errors of filters. System stability and uniformly ultimately fixed‐time boundedness of all states are proven using the Lyapunov stability theory. Finally, the limits of the acceleration components of the maneuvering target perpendicular to the line of sight direction are derived. The effectiveness of the designed IGC scheme and the ability of multi‐stage interconnected observers to sense disturbances with each other are verified through simulations.

automation & control systems,engineering, electrical & electronic,instruments & instrumentation
Integrated Missile Guidance and Control Using Adaptive Sliding Mode Approach

Wang Xianghua,Wang Jinzhi

2012-01-01

Abstract:A novel method for the integrated guidance and control of a missile in the three-dimensional space is given. In this formulation, a projection decomposition in 3-space, which transforms a three-dimensional intercept into two planar ones is proposed. Firstly, the design in the horizontal plane with regard to the yaw channel of the missile is to keep the missile and target moving in the same longitudinal plane. Whereafter, a planar intercept forms in this longitudinal plane, which is only related to the pitch channel of the missile. Therefore, the intractable 3-space design process can be significantly reduced. To use as little information as possible about target, an adaptive sliding mode integrated guidance and control (ASMIGC) approach is introduced in both planes. An interesting and desirable aspect of the controller is that it does not require the boundary values about the target acceleration, what is more, the robustness to uncertainties is implemented. The effectiveness of the approach is demonstrated through a series of simulations with a 6-DOF missile model. Representative numerical results show that against agile targets, the given approach obtains a high Hit-to-Kill accuracy with reasonable fin deflections.
Robust partial integrated guidance and control for missiles via extended state observer

Qing Wang,Maopeng Ran,Chaoyang Dong

DOI: https://doi.org/10.1016/j.isatra.2016.08.017

IF: 7.3

2016-11-01

ISA Transactions

Abstract:A novel extended state observer (ESO) based control is proposed for a class of nonlinear systems subject to multiple uncertainties, and then applied to partial integrated guidance and control (PIGC) design for a missile. The proposed control strategy incorporates both an ESO and an adaptive sliding mode control law. The multiple uncertainties are treated as an extended state of the plant, and then estimate them using the ESO and compensate for them in the control action, in real time. Based on the output of the ESO, the resulting adaptive sliding mode control law is inherently continuous and differentiable. Strict proof is given to show that the estimation error of the ESO can be arbitrarily small in a finite time. In addition, the adaptive sliding mode control law can achieve finite time convergence to a neighborhood of the origin, and the accurate expression of the convergent region is given. Finally, simulations are conducted on the planar missile-target engagement geometry. The effectiveness of the proposed control strategy in enhanced interception performance and improved robustness against multiple uncertainties are demonstrated.

automation & control systems,instruments & instrumentation,engineering, multidisciplinary
Active disturbance rejection control design for integrated guidance and control missile based SMC and extended state observer

Hong Toan Dinh,Dang Khoa Truong,Tran Hiep Nguyen,Xuan Tung Truong,Cong Dinh Nguyen

DOI: https://doi.org/10.1109/icsse.2017.8030920

2017-07-01

Abstract:This paper presents an active disturbance rejection rejection control design for integrated guidance and control missile based on sliding mode control and extended state observer. The integrated model is formulated as a block-strict-feedback nonlinear system, in which modeling errors, unmodeled non-linearities, target maneuvers, etc. are viewed as unknown uncertainties. The nonlinear control law is designed based on backstepping and sliding mode control (SMC) techniques. Based on the principle of active disturbance rejection control (ADRC), enhanced feedback linearization (FL) based control law is implemented for the IGC model using the estimates generated by an extended state observer (ESO). The stability analysis of the closed-loop system is also conducted. Simulation results show that, small miss distances and smooth missile trajectories are achieved, and the system is robust against system uncertainties and external disturbances.
Application of PID Controller to 2D Differential Geometric Guidance and Control Problem

Chaoyong Li,Wuxing Jing

DOI: https://doi.org/10.1109/CHICC.2006.280893

2007-01-01

Abstract:This paper presents the application of the proportional-integral-derivative (PID) controller to the development of the flight control system (FCS) for two-dimensional (2D) differential geometric (DG) guidance and control problem. In particular, the performance of the designed FCS is investigated. To this end, the commanded angle-of-attack (AOA) is firstly developed in the time domain using the classical DG formulations. Then, the classical PID controller is introduced to develop a FCS so as to form the 2D DG guidance and control system, and the PID controller parameters are determined by the Ziegler-Nichols method as well as the Routh-Hurwitz stability algorithm to guarantee a fast convergence of the system error. The results demonstrate that the designed controller yields a fast responding FCS, and the resulting DG guidance and control system is viable and effective in a realistic missile defense engagement.
Partial Integrated Missile Guidance and Control with State Observer

Xianghua Wang,Jinzhi Wang,Gang Gao

DOI: https://doi.org/10.1007/s11071-014-1828-9

IF: 5.741

2014-01-01

Nonlinear Dynamics

Abstract:This paper conducts a partial integrated guidance and control design for missile interception. With only the output available for feedback, a novel state observer is firstly proposed in the presence of unknown disturbances. The proposed observer reconstructs full system states in finite time. Interestingly, observer parameter is updated by an adaptive law. Then, a terminal sliding mode controller based on the proposed observer ensures the system states converge to zero in finite time, which is proved by the Lyapunov stability theory. The obtained result is applied to partial integrated guidance and control design of missile and hit-to-kill interception is achieved. Finally, a simulation example is presented, and a comparison to standard sliding mode observer is discussed to illustrate effectiveness of the proposed method.
Integrated design of interceptor guidance and control considering modeling error

SONG Hai-tao,Tao Zhang,ZHANG Guo-liang,YANG Wei-feng

DOI: https://doi.org/10.3969/j.issn.1000-1093.2013.09.018

2013-01-01

Abstract:An integrated control law is designed by modifying the existing modeling results and using the intelligent control method for the guidance and control of interceptor during the terminal course. While the modeling error caused by approximate linearization and ignoring couplings is taken into consideration, a model error compensation is used to modify the interceptor dynamics. A nonlinear model for the integrated guidance and control (IGC) is obtained. The adaptive dynamic surface control is proposed for the controller design of this mismatched nonlinear system. The influence of mismatched uncertainties on the system performance is eliminated, and the term explosion in traditional backstepping method is avoided. The integrated control law is used to establish a direct relationship between control objective and actuators command. Compared with the controller which ignores the modeling error in interception simulation, the proposed controller shows better interception performance.
Application of PID Controller to 2D Differential Geometric Guidance Problem

Chaoyong Li,Wuxing Jing

DOI: https://doi.org/10.1007/s11768-006-6109-9

2007-01-01

Journal of Control Theory and Applications

Abstract:This paper presents the application of the proportional-integral-derivative (PID) controller to the flight control system (FCS) for two-dimensional (2D) differential geometric (DG) guidance and control problem. In particular, the performance of the designed FCS is investigated. To this end, the commanded angle-of-attack is firstly developed in the time domain using the classical DG formulations. Then, the classical PID controller is introduced to develop a FCS so as to form the 2D DG guidance and control system, and the PID controller parameters are determined by the Ziegler-Nichols method as well as the Routh-Hurwitz stability algorithm to guarantee the convergence of the system error. The results demonstrate that the designed controller yields a fast responding system, and the resulting DG guidance and control system is viable and effective in a realistic missile defense engagement.
Integrated guidance and control for missile with narrow field-of-view strapdown seeker

Jiayi Tian,Neng Xiong,Shifeng Zhang,Huabo Yang,Zhenyu Jiang

DOI: https://doi.org/10.1016/j.isatra.2020.06.012

Abstract:Due to the removal of the mechanically stable platform in the conventional gimbaled seeker, the strapdown seeker's measurement is coupled with the missile body attitude motion, such that the inertial line-of-sight (LOS) angular rate required to implement traditional guidance laws cannot be measured, and the field-of-view (FOV) limit must be considered when designing guidance and control systems for a strapdown homing missile. To address these practical problems, an integrated guidance and control (IGC) scheme with considering the FOV limit is proposed in this paper. A novel IGC model is first derived based on the body-LOS (BLOS) angle that a strapdown seeker can directly measure, and then an IGC controller is designed using the dynamic surface control technique. A great merit of this design is that the inertial LOS angle and its angular rate are not needed, and thus the filters/estimators required to extract this guidance information in previous studies can be canceled. Next, by using the output to input saturation transformation (OIST) technique, the FOV limit, which is always considered as a state/output constraint, is transformed to a time-varying boundary limitation on the control input, and then is handled simultaneously with the actuator saturation constraint. Finally, extensive numerical simulations against both stationary and moving targets are performed to fully demonstrate the efficiency of the proposed IGC law.
Application of the 3D Differential Geometric Guidance Commands

Chao-yong LI,Wu-xing JING,Zhi-guo QI,Hui WANG

DOI: https://doi.org/10.3321/j.issn:1000-1328.2007.05.032

2007-01-01

Abstract:The application of three-dimensional(3D) differential geometric(DG) guidance commands to a realistic tactical missile interception scenario is investigated.In particular,the capture capability and interception performance of the law are analyzed.The classical DG formulations are utilized firstly to transform the DG guidance commands from the arc-length system to the time domain.Then,an algorithm for commanded angle-of-attack and sideslip angle is introduced to form the 3D DG guidance law.Finally,a new necessary initial condition is deduced to guarantee intercepting and/or capture of high speed targets,as well as to prevent singularity of guidance commands throughout the operation envelope.Simulations results demonstrate that the proposed guidance law performs better than classical proportional navigation guidance law in the case of intercepting a maneuvering target.
Asymmetric integral barrier Lyapunov function-based three-dimensional integrated guidance and control design with field-of-view constraint and input saturation

Dan Feng,Mingshan Hou,Wencong Wang,Dongyue Wang

DOI: https://doi.org/10.1177/16878132241235753

IF: 2.1

2024-03-15

Advances in Mechanical Engineering

Abstract:Advances in Mechanical Engineering, Volume 16, Issue 3, March 2024. This paper proposes an adaptive integrated guidance control (IGC) scheme for the flight vehicle intercepting the maneuvering target with asymmetric field-of-view angle constraint, input magnitude and rate saturation, and system uncertainties. A novel nonlinear three-dimensional IGC model is established in the body line-of-sight (LOS) coordinate system by employing the dual-integral control law. Based on this model, the input magnitude and rate saturation for the conventional IGC system can be converted to the limitations of the new augmented states. Asymmetric integral barrier Lyapunov function and dynamic surface control approach are applied to deal with the asymmetric state constraints of the proposed IGC model, and adaptive control laws are designed to compensate for model uncertainties. Furthermore, based on the Lyapunov stability theory, it is proved that all signals in the closed-loop system are bounded while the constrained states are not violated. Finally, the effectiveness and robustness of the proposed IGC scheme are illustrated with numerical simulations.

engineering, mechanical,thermodynamics
Iterative solution to differential geometric guidance problem

Chaoyong Li,Wuxing Jing,Hui Wang,Zhiguo Qi

DOI: https://doi.org/10.1108/00022660610685800

2006-01-01

Aircraft Engineering and Aerospace Technology

Abstract:Purpose - To study the application of three-dimensional differential geometric (DG) guidance commands to a realistic missile defense engagement, and the application of the Newton's iterative algorithm to DG guidance problems. Design/methodology/approach - The classical differential geometry theory is introduced firstly to transform all the variables in DG guidance commands from an arc length system to the time domain. Then, an algorithm for the angle-of-attack and the sideslip angle is developed by assuming the guidance curvature command and guidance torsion command equal to its corresponding value of current trajectory. Furthermore, Newton's iteration is utilized to develop iterative solution of the stated algorithm and the two-dimensional DG guidance system so as to facilitate easy computation of the angle-of-attack and the sideslip angle, which are formulated to satisfy the DG guidance law. Findings - DG guidance law is viable and effective in the realistic missile defense engagement, and it is shown to be a generalization of gain-varying proportional navigation (PN) guidance law and performs better than the classical PN guidance law in the case of intercepting a maneuvering target. Moreover, Newton's iterative algorithm has sufficient accuracy for DG guidance problem. Originality/value - Provides further study on DG guidance problem associated with its iterative solution.

Hemodynamics and gas exchange during carbon dioxide insufflation for totally endoscopic coronary artery bypass grafting.

Robust I&I Adaptive Dsc With Disturbance Observer For Maglev System With Output Constraint

Robust Immersion and Invariance Adaptive Coordinated Control for a Class of Biaxial Gantry Systems

A novel non-singular terminal sliding mode control-based integrated missile guidance and control with impact angle constraint

Integrated Missile Guidance And Control Design With Smooth Adaptive Sliding Mode Control

Impact angle-constrained integrated guidance and control for supersonic skid-to-turn missiles using backstepping with global fast terminal sliding mode control

Dasherkandi project studies. Demography, morbidity and mortality in a rural community of Bangladesh.

Integrated guidance and control design by active disturbance rejection method for high-velocity target interceptor with DCS thruster

Integrated Guidance and Control Method for the Interception of Maneuvering Hypersonic Vehicle Based on High Order Sliding Mode Approach

Multiple‐missile fixed‐time integrated guidance and control design with multi‐stage interconnected observers under impact angle and input saturation constraints

Integrated Missile Guidance and Control Using Adaptive Sliding Mode Approach

Robust partial integrated guidance and control for missiles via extended state observer

Active disturbance rejection control design for integrated guidance and control missile based SMC and extended state observer

Application of PID Controller to 2D Differential Geometric Guidance and Control Problem

Partial Integrated Missile Guidance and Control with State Observer

Integrated design of interceptor guidance and control considering modeling error

Application of PID Controller to 2D Differential Geometric Guidance Problem

Integrated guidance and control for missile with narrow field-of-view strapdown seeker

Application of the 3D Differential Geometric Guidance Commands

Asymmetric integral barrier Lyapunov function-based three-dimensional integrated guidance and control design with field-of-view constraint and input saturation

Iterative solution to differential geometric guidance problem