Status of pyrethroid resistance and mechanisms in Brazilian populations of Tuta absoluta.

W. M. Silva,Madeleine Berger,C. Bass,V. Balbino,Marcelo H. Amaral,M. R. Campos,H. Siqueira

DOI: https://doi.org/10.1016/j.pestbp.2015.01.011

IF: 4.966

2015-07-01

Pesticide Biochemistry and Physiology

Abstract:

What problem does this paper attempt to address?

Nanoporous core–shell Cu@Cu2O nanocomposites with superior photocatalytic properties towards the degradation of methyl orange

tianyi kou,chuanhong jin,chi zhang,junzhe sun,zhonghua zhang

DOI: https://doi.org/10.1039/c2ra21821f

IF: 4.036

2012-01-01

RSC Advances

Abstract:We present a facile two-step strategy to fabricate a novel nanoporous core-shell Cu@Cu2O nanocomposite photocatalyst. The photocatalyst was synthesized via the combination of dealloying of the as-milled Al66.7Cu33.3 (at.%) precursor powders in alkaline media with subsequent surface oxidation in air. The microstructure of the as-prepared photocatalyst has been characterized by X-ray diffraction (XRD), a field-emission scanning electron microscope (FESEM) and a transmission electron microscope (TEM). The results show that the as-prepared photocatalyst exhibits an open, bicontinuous interpenetrating ligament (ca. 30 nm)-channel (ca. 15 nm) structure, and is comprised of Cu (core) and Cu2O (shell) phases. Methyl orange (MO) was used as the model pollutant, and photodegradation experiments were monitored by UV-vis spectrophotometry. The nanoporous core-shell Cu@Cu2O photocatalyst shows excellent photocatalytic activity towards the degradation of MO under sunlight. The MO degradation rate can reach as high as 8.04 mg min(-1) g(cat)(-1). In addition, the influence of additive amounts of photocatalyst and initial concentrations of MO on the photodegradation process has been investigated. The photodegradation mechanism of the as-prepared photocatalyst has also been discussed.
Enhanced Photocatalytic Activity of Biosynthesized Au-Ag/TiO2 Catalyst by Removing Excess Anchored Biomolecules

Xinde Jiang,Zhenxi Wang,Xiaohang Zhang,Guixian Jiang,Yong Peng,Sheng Xu,Meng Cao,Xin Dai,Zuhan Liu,Jianye Ma

DOI: https://doi.org/10.1007/s11051-019-4622-2

IF: 2.533

2019-01-01

Journal of Nanoparticle Research

Abstract:A green bioreduction method was used to prepare highly efficient supported TiO2 photocatalysts with bimetallic (Au-Ag) nanoparticles at room temperature using Cinnamomum camphora leaf extract as both the protective agent and reducing agent. The resulted Au-Ag/TiO2 exhibits high photocatalytic activity toward the degradation of organic dyes. It was demonstrated that after some of the biomolecules were removed through ionic-liquid extraction and/or calcinations, the Au-Ag/TiO2 photocatalyst exhibits significantly enhanced catalytic performance toward the degradation of methyl orange compared to the pristine untreated catalyst. As a result, 300 mL of 20 mg/mL methyl orange can be fully degraded in 30 min. These can be explained by the sufficient biomolecules could protect the nanoparticles stay in small size, but excess biomolecules played an unfavorable role in hindering the electron transportation during the catalytic reaction. The low-cost preparation, the high activity, together with the good stability and recyclability make this developed Au-Ag/TiO2 a promising photocatalyst toward the degradation of wastewater.
Ag–CuO–ZnO Metal–semiconductor Multiconcentric Nanotubes for Achieving Superior and Perdurable Photodegradation

Kaichen Xu,Jiagen Wu,Chuan Fu Tan,Ghim Wei Ho,Ang Wei,Minghui Hong

DOI: https://doi.org/10.1039/c7nr03279j

IF: 6.7

2017-01-01

Nanoscale

Abstract:Solar energy represents a robust and natural form of resource for environment remediation via photocatalytic pollutant degradation with minimum associated costs. However, due to the complexity of the photodegradation process, it has been a long-standing challenge to develop reliable photocatalytic systems with low recombination rates, excellent recyclability, and high utilization rates of solar energy, especially in the visible light range. In this work, a ternary hetero-nanostructured Ag-CuO-ZnO nanotube (NT) composite is fabricated via facile and low-temperature chemical and photochemical deposition methods. Under visible light irradiation, the as-synthesized ZnO NT based ternary composite exhibits a greater enhancement (∼300%) of photocatalytic activity than its counterpart, Ag-CuO-ZnO nanorods (NRs), in pollutant degradation. The enhanced photocatalytic capability is primarily attributed to the intensified visible light harvesting, efficient charge carrier separation and much larger surface area. Furthermore, our as-synthesised hybrid ternary Ag-CuO-ZnO NT composite demonstrates much higher photostability and retains ∼98% of degradation efficiency even after 20 usage cycles, which can be mainly ascribed to the more stable polar planes of ZnO NTs than those of ZnO NRs. These results afford a new route to construct ternary heterostructured composites with perdurable performance in sewage treatment and photocorrosion suppression.
UiO-66-NH2/Cu2O composite as an enhanced visible light photocatalyst for decomposition of organic pollutants

Qiang Zhao,Junli Wang,Zuopeng Li,Yong Guo,Jing Wang,Bing Tang,Yasuki Kansha,Akihiro Yoshida,Abuliti Abudula,Guoqing Guan

DOI: https://doi.org/10.1016/j.jphotochem.2020.112625

2020-08-01

Abstract:UiO-66-NH2/Cu2O composites with different loading amounts of UiO-66-NH2 were successfully synthesized by using a facile impregnation process. The photocatalytic performances of the composites were measured by the methyl orange (MO) degradation. It is found that the developed UiO-66-NH2/Cu2O composites possessed better photocatalytic behavior than the pure Cu2O, and the 20 wt% UiO-66-NH2/Cu2O photocatalyst showed the excellent photodegradation activity, by which 98.6% of MO could be decomposed within 50 min. In addition, it showed an excellent reusability since the severe photocorrosion issue of Cu2O was suppressed significantly by combining with UiO-66-NH2. The excellent photodegradation efficiency of 20 wt% UiO-66-NH2/Cu2O should be due to the synergistic effect between Cu2O and UiO-66-NH2, in which efficient interfacial charge transfer improved the separation effect of photoinduced electron-hole pairs within the Z-scheme heterojunction The active species trapping experiments indicated that the photo-generated h+ and O2 − radicals were the major active species involved in the MO degradation under visible light.

chemistry, physical
Cu 2 O/Ag-coated wood-based biochar composites for efficient adsorption/photocatalysis synergistic degradation of high-concentration azo dyes

Ying Zhang,Junfeng Chen,Yanan Wang,Huicheng Dou,Zuopeng Lin,Xing Gao,Xueqi Chen,Minghui Guo

DOI: https://doi.org/10.1016/j.apsusc.2023.158985

IF: 6.7

2023-11-27

Applied Surface Science

Abstract:In order to effectively eliminate organic azo dyes with high concentrations from aqueous environments, novel adsorption/photocatalysis composites were prepared using Cu 2 O/Ag-coated carriers based on renewable wood-based biochar (MBC). The adsorption process of the prepared MBC@Cu 2 O/Ag-3 under electrostatic attraction, hydrogen bonding, and complexation effects was conformed to the proposed second-order kinetic model, and the total sorption capacity of Congo red (CR) and methyl orange (MO) reached 264.55 and 178.63 mg g −1 , respectively. Moreover, the coordinated interaction of MBC, Cu 2 O, and Ag enhanced the visible light absorptivity, which further facilitated the effective dissociation of light-generated electrons from holes. The removal rates of CR and MO by MBC@Cu 2 O/Ag-3 in the presence of visible light were up to 98.4 % and 97.8 %, respectively. In addition, free radical capture and electron spin resonance (ESR) spectroscopy analyses indicated that superoxide ( ·O2- ) and hydroxyl (·OH) radicals were major activators during the photocatalytic progression, and the adsorption/photocatalysis mechanism was elucidated through a series of characterization experiments. This work shows that the utilization of natural biomass materials for the preparation of adsorption/photocatalysis composites with high added value can significantly contribute to water environmental protection and sustainable development.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Wood powder biochar in CdS-WPB-g-C 3 N 4 heterojunction as an electron transfer medium for enhancing photocatalytic performance toward degradation methyl orange

Chang Ma,Ying Zhang,Bin Yin,Junfeng Chen,Minghui Guo,Xing Gao

DOI: https://doi.org/10.1016/j.jece.2022.109135

IF: 7.7

2022-12-15

Journal of Environmental Chemical Engineering

Abstract:Biochar-based photocatalysts were rarely used in wastewater treatment, as the low efficiency of the electron transfer often limited their applicability. In this work, a novel ternary CdS-WPB-CN heterojunction was constructed for the efficient degradation of methyl orange (MO) under UV and visible light. As a green and low-cost electron transfer medium, wood powder biochar (WPB) plays an important role in rapidly transporting photogenerated electrons from g-C 3 N 4 to CdS, significantly improving photogenerated carriers' separation efficiency. Under the optimal degradation condition (1 g/L photocatalyst dosage and 10 mg/L of initial MO concentration), the degradation efficiency for MO of the ternary CdS-WPB(5%)-CN composite reached 99% within 80 min under visible light irradiation. Moreover, it could completely degrade MO within 60 min under UV irradiation. Besides, the outstanding reusability and stability of the CdS-WPB-CN composite were further verified by five consecutive cycle experiments. The degradation experiment in the actual river water body confirmed the excellent applicability in real wastewater samples. Finally, a mechanism was proposed to explain the photocatalytic degradation of MO. Overall, this work provides important insights into the role of biochar in improving the photocatalytic degradation of organic contaminants.

engineering, chemical, environmental
Au Nanoparticles Embedded on Urchin-Like Tio2 Nanosphere: an Efficient Catalyst for Dyes Degradation and 4-Nitrophenol Reduction

Zheng-Hui Ren,Hai-Tao Li,Qiang Gao,Hao Wang,Bo Han,Kai-Sheng Xia,Cheng-Gang Zhou

DOI: https://doi.org/10.1016/j.matdes.2017.02.064

IF: 9.417

2017-01-01

Materials & Design

Abstract:The development of efficient heterogeneous catalysts for degrading organic pollutants or converting them into harmless and even useful products is of vital significance for environmental remediation. Herein, we reported the facile synthesis of a highly active and stable nanocatalyst (AuNPs/uTiO2) via a simple photoreduction deposition of Au nanoparticles (AuNPs) on urchin-like TiO2 nanosphere (uTiO2), and demonstrated its excellent performances as a catalyst for oxidative degradation of organic dyes and reductive conversion of 4-nitrophenol (4-NP). The AuNPs/uTiO2 nanocomposite showed high surface area (147.5m2·g−1), large pore volume (0.52cm3·g−1), and high dispersity of AuNPs. In particular, the uTiO2 support could combine AuNPs strongly and serve as a shield to prevent leaching or aggregation of AuNPs, while allowing guest organic molecules to diffuse in and out easily. Benefiting from the excellent characteristics, the AuNPs/uTiO2 exhibited superior catalytic properties for dyes degradation and 4-NP reduction with significantly higher catalytic efficiencies than many previously reported heterogeneous catalysts. Moreover, the catalytic activity of AuNPs/uTiO2 could remain almost unchanged after being recycled for several times, demonstrating its long-term stability. The AuNPs/uTiO2, combining the advantages of high activity, favorable kinetics, and excellent durability for dye degradation and 4-NP reduction, should be very promising for wastewater treatment.
Sustainable wood-based nanotechnologies for photocatalytic degradation of organic contaminants in aquatic environment

Xinyi Liu,Caichao Wan,Xianjun Li,Song Wei,Luyu Zhang,Wenyan Tian,Ken-Tye Yong,Yiqiang Wu,Jian Li

DOI: https://doi.org/10.1007/s11783-020-1346-6

2020-11-09

Abstract:Wood-based nanotechnologies have received much attention in the area of photocatalytic degradation of organic contaminants in aquatic environment in recent years, because of the high abundance and renewability of wood as well as the high reaction activity and unique structural features of these materials. Herein, we present a comprehensive review of the current research activities centering on the development of wood-based nanocatalysts for photodegradation of organic pollutants. This review begins with a brief introduction of the development of photocatalysts and hierarchical structure of wood. The review then focuses on strategies of designing novel photocatalysts based on wood or its recombinants (such as 1D fiber, 2D films and 3D porous gels) using advanced nanotechnology including sol-gel method, hydrothermal method, magnetron sputtering method, dipping method and so on. Next, we highlight typical approaches that improve the photocatalytic property, including metal element doping, morphology control and semiconductor coupling. Also, the structure-activity relationship of photocatalysts is emphasized. Finally, a brief summary and prospect of wood-derived photocatalysts is provided.

environmental sciences,engineering, environmental
MOF-on-MOF-derived Fe Zr bimetal oxides supported on hierarchically porous carbonized wood to promote photo-Fenton degradation of ciprofloxacin

Kaiqian Li,Xupeng Zhang,Xueqin Huang,Xianghong Li,Qiaowen Chang,Shuduan Deng,Gang Zhu

DOI: https://doi.org/10.1016/j.jwpe.2024.105442

IF: 7

2024-05-11

Journal of Water Process Engineering

Abstract:MOF-on-MOF derivatives have served as promising heterogeneous Photo-Fenton (hetero-PF) catalysts, but its self-aggregation instability and limited photocatalytic activity inhibit the effective ciprofloxacin (CIP) removal. In this study, a novel hetero-PF catalyst, dual MOF-derived FeZr bimetal oxide embedded in a wood-converted porous carbon skeleton (ZrO 2 @Fe 3 O 4 /WPC), was successfully synthesized via a straightforward in-situ growth strategy combined with co-pyrolysis. The as-prepared hybrid photocatalysts, featuring a large surface area, effective porous structures, efficient light absorption and a narrow band gap demonstrated superior photo-Fenton activity, accomplishing approximately 99.1 % degradation of CIP within 120 min under neutral conditions. Furthermore, the ZrO 2 @Fe 3 O 4 /WPC hetero-PF system showed satisfactory performance in treating real water matrices. It can be inferred that the abundant heterojunctions, resulting from the synergistic effect of FeZr mixed oxide and the porous carbonized wood substrate, contributed to the rapid separation and migration of photogenerated electron-hole pairs. Meanwhile, the FeZr site in the graphitized carbon framework activates H 2 O 2 to accelerate the generation of the OH and O 2 − radicals, leading to a heightened degradation efficiency of CIP. Besides, the photodegradation pathway of CIP is obtained by liquid chromatography-mass spectrometry (LC-MS). This study indicates that combining porous carbonized wood and heterometallic MOF derived materials provides a promising method for realizing high-efficiency photo-Fenton degradation of antibiotic water pollutions.

engineering, chemical, environmental,water resources
Nano-PAA-CuCl2 Composite as Fenton-Like Reusable Catalyst to Enhanced Degrade Organic Pollutant MB/MO

Yang Dang,Yu Cheng,Yukun Zhou,Yifei Huang,Kaige Wang

DOI: https://doi.org/10.3390/catal11010010

IF: 3.9

2020-12-24

Catalysts

Abstract:The treatment of organic dye contaminants in wastewaters has now becoming more imperative. Fenton-like degradation of methylene blue (MB) and methyl orange (MO) in aqueous solution was investigated by using a nanostructure that a layer of CuCl2 nanoflake film grown on the top surface of nanoporus anodic alumina substrate (nano-PAA-CuCl2) as catalyst. The new nano-PAA-CuCl2 composite was fabricated with self-assembly approach, that is, a network porous structure film composed of CuCl2 nanoflake grown on the upper surface of nanoporous anodic alumina substrate, and the physical and chemical properties are characterized systematically with the X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), and high-resolution transmission electron microscopy (HRTEM), Energy Dispersive Spectrometer (EDS), X-ray photoelectron spectroscopy (XPS). The experimental results showed that the nano-PAA-CuCl2 catalyst presented excellent properties for the degradation of two typical organic pollutants such as MB and MO, which were almost completely degraded with 8 × 10−4mol/L nano-PAA-CuCl2 catalyst after 46 min and 60 min at reaction conditions of H2O2 18 mM and 23 mM, respectively. The effects of different reaction parameters such as initial pH, H2O2 concentration, catalyst morphology and temperature were attentively studied. And more, the stability and reusability of nano-PAA-CuCl2 were examined. Finally, the mechanism of MB and MO degradation by the nano-PAA-CuCl2/H2O2 system was proposed, based on the experimental data of the BCA and the temperature-programmed reduction (H2-TPR) and theoretical analysis, the reaction kinetics belonged to the pseudo-first-order equation. This new nanoporous composite material and preparation technology, as well as its application in Fenton-like reaction, provide an effective alternative method with practical application significance for wastewater treatment.

chemistry, physical
Chemically fabricated ZnO/Ag/Ag Mo O /Zn Mo O heterojunction nanophotocatalysts for abating organic dyes in wastewater

Liming Bai,Ruibo Guo,Zhao Chen,Lumin Liu,Guohua Dong,Jianwei Zhang,Yang Wu,Huaping Zhao,Dan Shan,Yuanyuan Su,Jiyuan Zhang,Baiqi Wang

DOI: https://doi.org/10.1016/j.jclepro.2022.132481

IF: 11.1

2022-08-01

Journal of Cleaner Production

Abstract:Semiconductor photocatalytic technology is among the most promising technologies for degrading organic pollutants in wastewater. However, broadening the photocatalytic spectral-response region of the nanomaterial and tuning carrier behavior at heterojunction interfaces remain wastewater-treatment challenges. To address this issue, we fabricated ZnO/Ag/Ag m Mo n O l /Zn x Mo y O z (ZAAZ) heterojunction nanophotocatalysts through a simple one-step chemical reaction between active ZnO nanoparticles and Ag/Ag x H3−x PMo12O40 (Ag/AgPMo). The as-prepared ZAAZ heterojunction nanophotocatalysts were physically and chemically characterized, photocatalytic activity was evaluated, and the photogenerated carrier-transfer mechanism analyzed. The optimal nanophotocatalyst was highly crystalline and exhibited a bandgap and specific surface area of 3.06 eV and 13.9 m2 g−1, respectively; it photodegraded almost 100% of the initial Rhodamine B (RhB) concentration in 90 min under the optimized conditions, which is 3.7-times faster than ZnO nanoparticles. Furthermore, the ZAAZ heterojunction nanophotocatalyst delivered a photocurrent of 8.3 μA cm−2, which is 31-times higher than that of its ZnO nanoparticle counterpart; it efficiently separated photogenerated carriers, transferred interfacial charges, and degraded 97% of the initial RhB concentration after three cycles of use, highlighting its excellent recyclability. These findings suggest that the developed heterojunction nanophotocatalyst is highly efficient for the photocatalytic degradation of organic water pollutants.

environmental sciences,green & sustainable science & technology,engineering, environmental
Fabrication of ZnO/Au@Cu2O heterojunction towards deeply oxidative photodegradation of organic dyes

Xueqin Yuan,Fei Pei,Xiaolin Luo,Huanting Hu,Huaming Qian,Pin Wen,Kangkang Miao,Sifan Guo,Wei Wang,Guodong Feng

DOI: https://doi.org/10.1016/j.seppur.2021.118301

IF: 8.6

2021-05-01

Separation and Purification Technology

Abstract:Fabrication of heterojunction is an effective way of improving the photocatalytic performance of semiconductor in the photocatalytic wastewater treatment. ZnO/2O heterojunctions were successfully synthesised using Au nanoparticles loaded onto the surface of ZnO nanorods as heterostructural seeds to induce in situ growth of Cu2O shells. X-ray diffraction, transmission electron microscopy, scanning electron microscopy, X-ray photoelectron spectroscopy, electrochemical workstation and UV-vis diffuse reflection spectrograph were employed to analyze the structures, compositions and photoelectric properties of the synthesised photocatalysts. After 45–90 min of the photocatalysis of ZnO/2O heterojunctions under simulated sunlight, the degradation efficiencies of methyl orange and rhodamine B could reach 93.0% and 99.6%, respectively, which were much higher than those with mono- and bi-component catalysts. The photocatalytic system with ZnO/2O can achieve deep mineralization to decompose organic dye molecules into non-toxic products. The formation of heterostructures not only could expand the spectral absorption range to the visible region but also efficiently facilitate charge separation to transfer more photo-generated holes and electrons to generate oxidative hydroxyl and superoxide radicals. A Z-scheme charge separation mechanism was proposed according to the determination of radical species and energy band structures of ZnO–Cu2O.

engineering, chemical
Cu2O-based binary and ternary photocatalysts for the degradation of organic dyes under visible light

Weijie Lei,Hao Wang,Xiaojing Zhang,Zhimao Yang,Chuncai Kong

DOI: https://doi.org/10.1016/j.ceramint.2021.09.255

IF: 5.532

2022-01-01

Ceramics International

Abstract:As competitive photocatalysts, Cu2O nanoparticles meet with severe photogenerated carries recombination and insufficient light absorption, leading to the poor photocatalytic performance. Herein, the truncated Cu2O-Au (CA) binary and Cu2O-Au-TiO2 (CAT) ternary octahedra with Au nanoparticles (Au NPs), preferentially supported on the (110) and (100) planes of Cu2O, are synthesized for efficient photocatalytic degradation reactions. The photodegradation rates of MO of CA1 (Cu2O-Au containing 1 wt % Au) and CAT are as high as 95.61% and 96.5% under 60 min of visible light irradiation, respectively. On the one hand, the synergistic function of localized surface plasmon resonance (LSPR) of Au NPs and Schottky barrier accelerate the separation and transfer of photogenerated carriers. On the other hand, a Z-scheme electron transfer system is constructed in CAT to promote the photodegradation performance. According to the finite-difference-time-domain (FDTD) simulation result, there is a strong electric field enhancement at the contact sites between Au, Cu2O and TiO2, which accelerates the electron transfer to a large extent and separates the electron-hole pairs. Therefore, this work may provide an approach for the synthesis and applications of multiple heterostructure catalyst.

materials science, ceramics
Novel Cu-Fe bi-metal oxide quantum dots coupled g-C3N4 nanosheets with H2O2 adsorption-activation trade-off for efficient photo-Fenton catalysis

Mingen Liu,Hong Xia,Wenxin Yang,Xiaoyu Liu,Jiao Xiang,Xiaoming Wang,Liangsheng Hu,Fushen Lu

DOI: https://doi.org/10.1016/j.apcatb.2021.120765

2022-02-01

Abstract:Exploitation of catalysts with multi-active sites is very important for enhancing catalytic performance. 0D/2D hybrids, especially quantum dots (QDs)/nanosheets (NSs), have attracted increasing attentions for advanced oxidation processes due to high charge mobility and more active sites. However, 0D/2D hybrids with multi-active sites still remain a great challenge. Herein, 0D Cu-Fe bi-metal oxide QDs/2D g-C3N4 (CNNSs) exhibiting superior advantages beyond single-metal 0D/2D counterparts was fabricated via a facile one-step synthesis strategy for photo-Fenton catalysis. The synergy of ultrafine Cu-Fe sites on CNNSs led to outstanding tetracycline removal efficiency over a wide pH range. Our experiments and DFT calculations clearly demonstrated that except for the fast charge separation and transfer, this synergy could achieve the optimal H2O2 adsorption-activation trade-off on Cu-Fe sites, while also modify tetracycline absorption, leading to multiple synergies of adsorption-catalytic degradation and photocatalysis-Fenton oxidation. This work provides new insights in developing multi-functional 0D/2D hybrids for environment and energy applications.

chemistry, physical,engineering, chemical, environmental
Preparation of Cu/Cu2O/BC and Its Performance in Adsorption-Photocatalytic Degradation of Methyl Orange in Water

Gang Du,Yarong Ding,Canhua Li,Lanyue Zhang,Jiamao Li,Minghui Li,Weichang Zhu,Chuan He

DOI: https://doi.org/10.3390/ma17174306

2024-08-30

Abstract:In this study, we prepared a low-cost novel Cu/Cu2O/BC nanocomposite visible-light photocatalyst by the impregnation method using CuSO4·5H2O and rice husk biochar (BC) as raw materials and Na2S2O4 as a single reductant to improve the stability and dispersion of the Cu/Cu2O nanoparticles, in order to solve their aggregation tendency during photocatalysis. The morphology and structure of the Cu/Cu2O/BC were characterized using various analytical and spectroscopic techniques. The photocatalytic effect and cyclic stability of the synthesized photocatalyst on methyl orange (MO) removal were investigated under visible light radiation and various parameter conditions, including the mass ratio of BC to Cu/Cu2O, initial MO concentration, pH, temperature, and catalyst dosage. The results show that the synthesized Cu/Cu2O/BC nanocomposite composed of Cu/Cu2O spherical particles was loaded on the BC carrier, which has better stability and dispersion. The best adsorption-photocatalytic effect of the Cu/Cu2O/BC is exhibited when the mass ratio of BC to Cu/Cu2O is 0.2. A total of 100 mg of Cu/Cu2O/BC can remove 95% of the MO and 88.26% of the COD in the aqueous solution at pH = 6, T = 25 °C, and an initial MO concentration of 100 mg/L. After five cycles of degradation, the MO degradation rate in the sample can still remain at 78.41%. Both the quasi-secondary kinetic model and the Langmuir isothermal adsorption model describe the adsorption process. Additionally, the thermodynamic analysis demonstrates that the photocatalytic process follows the quasi-primary kinetic model and that the removal process is of spontaneous heat absorption. The photocatalyst described in this paper offers a cost-effective, easily prepared, and visible-light-responsive solution for water pollution treatment.
Tetanus in pregnancy. Report of a case of severe tetanus with survival of mother and child following trachetomy and artificial respiration.

M. Holmdahl,L. Thorén

IF: 9.8

American Journal of Obstetrics and Gynecology

Abstract:
Investigation of MO Adsorption Kinetics and Photocatalytic Degradation Utilizing Hollow Fibers of Cu-CuO/TiO2 Nanocomposite

George V Theodorakopoulos,Sergios K Papageorgiou,Fotios K Katsaros,George Em Romanos,Margarita Beazi-Katsioti

DOI: https://doi.org/10.3390/ma17184663

2024-09-23

Abstract:This comprehensive study explores the kinetics of adsorption and its photocatalytic degradation of methyl orange (MO) using an advanced copper-decorated photocatalyst in the form of hollow fibers (HFs). Designed to boost both adsorption capacity and photocatalytic activity, the photocatalyst was tested in batch experiments to efficiently remove MO from aqueous solutions. Various isotherm models, including Langmuir, Freundlich, Sips, Temkin, and Dubinin-Radushkevich, along with kinetic models like pseudo-first and pseudo-second order, Elovich, Bangham, and Weber-Morris, were utilized to assess adsorption capacity and kinetics at varying initial concentrations. The results indicated a favorable MO physisorption on the nanocomposite photocatalyst under specific conditions. Further analysis of photocatalytic degradation under UV exposure revealed that the material maintained high degradation efficiency and stability across different MO concentrations. Through the facilitation of reactive oxygen species generation, oxygen played a crucial role in enhancing photocatalytic performance, while the degradation process following the Langmuir-Hinshelwood model. The study also confirmed the robustness and sustained activity of the nanocomposite photocatalyst, which could be regenerated and reused over five successive cycles, maintaining 92% of their initial performance at concentrations up to 15 mg/L. Overall, this effective nanocomposite photocatalyst structured in the form of HF shows great promise for effectively removing organic pollutants through combined adsorption and photocatalysis, offering valuable potential in wastewater treatment and environmental remediation.
Enhancing visible-light-driven photocatalysis: unveiling the remarkable potential of H2O2-assisted MOF/COF hybrid material for organic pollutant degradation

Amila Kasun Abeysinghe,Yen-Ping Peng,Po-Jung Huang,Ku-Fan Chen,Chia-Hung Chen,Wu-Xing Chen,Fang-Yu Liang,Po-Yen Chien

DOI: https://doi.org/10.1007/s11356-024-34552-8

Abstract:In this study, we synthesized MOF/COF hybrid material (NH2-MOF-5/MCOF) by integrating NH2-MOF-5 (Zn) with a melamine-based COF (MCOF) to target the photocatalytic degradation of methylene blue (MB) dye. Characterization using SEM, XRD, XPS, FT-IR, and UV-DRS confirmed the synthesized MOF/COF hybrid's exceptional photocatalytic performance under visible light. The addition of H2O2 significantly enhanced the photocatalytic degradation, achieving removal rates of 90%, 92%, and 57% for 11.75 mg L-1, 30 mg L-1, and 83 mg L-1 of MB, respectively. Kinetic studies revealed first-order kinetics, with a rate constant nearly 3.5 times higher with added H2O2. We proposed a comprehensive photocatalytic mechanism elucidated through energy band structure analysis and scavenger tests. Our findings revealed the formation of a heterojunction between NH2-MOF-5 and MCOF, which mitigates electron-hole recombination, with ∙OH identified as the principal species governing methylene blue degradation. Moreover, the NH2-MOF-5/MCOF hybrid displayed excellent reusability and chemical stability over six cycles. Notably, this H2O2-assisted hybrid material demonstrated the removal of 99% of ibuprofen, a pharmaceutical drug, showcasing its broad applicability in removing organic contaminants in aqueous solutions, thereby holding great promise for wastewater treatment.
Study on the controlled preparation of ZnO/CdS and its photocatalytic performance enhanced by Au particles

Siyu Meng,Chao Xu,Zhenkun Duan,Yang Liu,Huifang Yao,Yongqian Wang

DOI: https://doi.org/10.1007/s10854-024-13595-0

2024-10-08

Journal of Materials Science Materials in Electronics

Abstract:Presently, the issue of water pollution is escalating, underscoring the paramount importance of research into catalyzing the degradation of water using renewable energy sources, such as solar energy. This study employs hydrothermal, chemical bath deposition, and atomic layer deposition (ALD) techniques to fabricate a sea urchin-shaped ZnO/CdS/Au ternary composite photocatalyst deposited on zinc foil. The collaborative effect of ZnO-absorbing ultraviolet light and CdS-absorbing visible light achieves a broad-spectrum response to ultraviolet–visible light. Au particles, acting as carrier bridges, facilitate the migration of charge carriers, thereby augmenting the photocatalytic performance. The material underwent comprehensive characterization of its surface morphology, phase structure, and optical properties employing scanning electron microscopy (SEM), energy-dispersive spectrometer (EDS), transmission electron microscopy (TEM), X-ray diffractometer (XRD), and ultraviolet–visible spectrophotometer (UV–Vis). The impact of hydrothermal time, temperature, and reaction system concentration on the microstructure and morphology is scrutinized. Experimental results show that ZnO/CdS/Au has a unique skeleton structure, which can provide more active sites and exhibit better photocatalytic activity. UV results indicate an intensified visible light absorption and a narrowed bandgap, resulting in enhanced photocatalytic performance. Photocatalytic applications demonstrate that within 60 min, the degradation rate of MB reaches 94.4%. This represents a 2.6-fold increase in degradation speed compared to pure ZnO and a 1.8-fold increase compared to the binary composite ZnO/CdS. In comparison to other catalysts, ZnO/CdS/Au possesses advantages, such as low cost, excellent stability, non-toxicity, and environmental friendliness. It emerges as a promising photocatalyst for the degradation of organic pollutants in wastewater treatment.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Heterogeneous activation of peroxymonosulfate by Cu+-decorated g-C3N4 under sunlight for degradation of organic pollutants

Linhai Yang,Xuechang Ren,Yujie Zhang,Zuoyan Chen

DOI: https://doi.org/10.1016/j.jece.2021.106596

IF: 7.7

2021-12-01

Journal of Environmental Chemical Engineering

Abstract:This article is an in-depth study of the basis of Cu+-decorated triazine-based g-C3N4 (Cu+/g-C3N4) nanosheet-activated H2O2. In this study, peroxymonosulfate (PMS) was activated by Cu+/g-C3N4 under sunlight and used to treat simulated wastewater RhB. The properties of g-C3N4 and Cu+/g-C3N4 were characterized by UV–Vis DRS and PL. The results indicated that the introduction of Cu+ in g-C3N4 can enhance the separation of photogenerated electron-hole pairs. The Cu+/g-C3N4(1:4) samples exhibited the best PMS activation performance under sunlight when 0.5 g/L catalyst dose and 0.5 mmol/L PMS concentration were used, and the removal rate of RhB reached 95.7% in 30 min. Moreover, better catalytic activity of the system can be achieved in the initial pH range of 2.0–10.0. The investigation results of the catalytic mechanisms showed that the prepared Cu+/g-C3N4 catalyst constructs a dual reaction center of Cu+/Cu2+ cycling and e CB − / h VB + transfer for efficient PMS activation. The degradation of pollutants benefits from the participation of a variety of free radicals, which are generated by sunlight-assisted heterogeneous activation of PMS. This study has resulted in substantial progress in activating multiple oxidants with a single heterogeneous catalyst and provides a feasible way to treat refractory wastewater using Cu+/g-C3N4 with PMS under sunlight.

engineering, chemical, environmental

Status of pyrethroid resistance and mechanisms in Brazilian populations of Tuta absoluta.

Nanoporous core–shell Cu@Cu2O nanocomposites with superior photocatalytic properties towards the degradation of methyl orange

Enhanced Photocatalytic Activity of Biosynthesized Au-Ag/TiO2 Catalyst by Removing Excess Anchored Biomolecules

Ag–CuO–ZnO Metal–semiconductor Multiconcentric Nanotubes for Achieving Superior and Perdurable Photodegradation

UiO-66-NH2/Cu2O composite as an enhanced visible light photocatalyst for decomposition of organic pollutants

Cu 2 O/Ag-coated wood-based biochar composites for efficient adsorption/photocatalysis synergistic degradation of high-concentration azo dyes

Wood powder biochar in CdS-WPB-g-C 3 N 4 heterojunction as an electron transfer medium for enhancing photocatalytic performance toward degradation methyl orange

Au Nanoparticles Embedded on Urchin-Like Tio2 Nanosphere: an Efficient Catalyst for Dyes Degradation and 4-Nitrophenol Reduction

Sustainable wood-based nanotechnologies for photocatalytic degradation of organic contaminants in aquatic environment

MOF-on-MOF-derived Fe Zr bimetal oxides supported on hierarchically porous carbonized wood to promote photo-Fenton degradation of ciprofloxacin

Nano-PAA-CuCl2 Composite as Fenton-Like Reusable Catalyst to Enhanced Degrade Organic Pollutant MB/MO

Chemically fabricated ZnO/Ag/Ag Mo O /Zn Mo O heterojunction nanophotocatalysts for abating organic dyes in wastewater

Fabrication of ZnO/Au@Cu2O heterojunction towards deeply oxidative photodegradation of organic dyes

Cu2O-based binary and ternary photocatalysts for the degradation of organic dyes under visible light

Novel Cu-Fe bi-metal oxide quantum dots coupled g-C3N4 nanosheets with H2O2 adsorption-activation trade-off for efficient photo-Fenton catalysis

Preparation of Cu/Cu2O/BC and Its Performance in Adsorption-Photocatalytic Degradation of Methyl Orange in Water

Tetanus in pregnancy. Report of a case of severe tetanus with survival of mother and child following trachetomy and artificial respiration.

Investigation of MO Adsorption Kinetics and Photocatalytic Degradation Utilizing Hollow Fibers of Cu-CuO/TiO2 Nanocomposite

Enhancing visible-light-driven photocatalysis: unveiling the remarkable potential of H2O2-assisted MOF/COF hybrid material for organic pollutant degradation

Study on the controlled preparation of ZnO/CdS and its photocatalytic performance enhanced by Au particles

Heterogeneous activation of peroxymonosulfate by Cu+-decorated g-C3N4 under sunlight for degradation of organic pollutants