Ketoconazole promotes parasitological cure of mice infected with Trypanosoma cruzi.

Robert E. McCabe,Robert E. McCabe,Jack S. Remington,Jack S. Remington,F. G. Araujo

DOI: https://doi.org/10.1016/0035-9203(87)90430-5

1987-07-01

Transactions of the Royal Society of Tropical Medicine and Hygiene

Abstract:

What problem does this paper attempt to address?

Recycling of Plastics in the Automotive Sector and Methods of Removing Paint for Its Revalorization: A Critical Review

Carla Zambrano,Pablo Tamarit,Ana Inés Fernandez,Camila Barreneche

DOI: https://doi.org/10.3390/polym16213023

IF: 5

2024-10-28

Polymers

Abstract:The presence of plastics in the automotive industry is increasingly significant due to their lightweight nature, which contributes to reducing fuel consumption and CO2 emissions while improving versatility and mechanical properties. Polypropylene (PP) and other polyolefins are among the most commonly used materials, especially for components such as bumpers. The use of composite materials, i.e., a combination of different polymers, improves the properties through synergistic effects, thereby also improving the performance of the final product. In the automotive industry, PP reinforced with 20% talc or CaCO3 is commonly used. The mechanical recycling of polypropylene bumpers is the most common type of recycling. However, challenges arise during this process, such as the presence of impurities like paint, chemical contaminants from previous use, and polymeric impurities from different polymers mixed into the polymer matrix, among others. Paint affects both the aesthetic quality and the mechanical and intrinsic properties of the recycled material. This review aims to analyze the main methods reported in the literature, focusing on those with low environmental impact. Furthermore, these methods are classified according to their capacity, effectiveness, substrate damage, environmental hazards, and economic feasibility. It also aims to offer a comprehensive overview of the mechanical recycling of plastic waste in the automotive industry.

polymer science
Challenges around automotive shredder residue production and disposal

Ala Khodier,Karl Williams,Neil Dallison

DOI: https://doi.org/10.1016/j.wasman.2017.05.008

Abstract:The challenge for the automotive industry is how to ensure they adopt the circular economy when it comes to the disposal of end-of-life vehicles (ELV). According to the European Commission the UK achieved a total reuse and recovery rate of 88%. This is short of the revised ELV directive target of 95% materials recovery, which requires a minimum of 85% of materials to be recycled or reused. A significant component of the recycling process is the production of automotive shredder residue (ASR). This is currently landfilled across Europe. The additional 10% could be met by processing ASR through either waste-to-energy facilities or Post shredder technology (PST) to recover materials. The UK auto and recycling sectors claimed there would need to be a massive investment by their members in both new capacity and new technology for PST to recover additional recycle materials. It has been shown that 50% of the ASR contains valuable recoverable materials which could be used to meet the Directive target. It is expected in the next 5years that technological innovation in car design will change the composition from easily recoverable metal to difficult polymers. This change in composition will impact on the current drive to integrate the European Circular Economy Package. A positive factor is that main driver for using ASR is coming from the metals recycling industry itself. They are looking to develop the infrastructure for energy generation from ASR and subsequent material recovery. This is driven by the economics of the process rather than meeting the Directive targets. The study undertaken has identified potential pathways and barriers for commercial thermal treatment of ASR. The results of ASR characterisation were used to assess commercial plants from around the world. Whilst there were many claiming that processing of ASR was possible none have so far shown both the technological capability and economic justification.
Engineering, Recyclable, and Biodegradable Plastics in the Automotive Industry: A Review

Horacio Vieyra,Joan Manuel Molina-Romero,Juan de Dios Calderón-Nájera,Alfredo Santana-Díaz

DOI: https://doi.org/10.3390/polym14163412

IF: 5

2022-08-22

Polymers

Abstract:The automotive industry has used plastics almost since the beginning. The lightness, flexibility, and many qualities of plastics make them ideal for the automotive industry, reducing cars' overall weight and fuel consumption. Engineering plastics in this industry belong to the high-performance segment of non-renewable resources. These plastics exhibit higher properties than commodity plastics. Fortunately, unlike recycled commodity plastics, the super properties and high-performance characteristics make engineering plastics effectively reused after recycling. The substitution of these fossil-fuel-derived plastics adds to the solution of lightweighting, a much-needed solution to waste management, and solves industrial and ecological issues surrounding plastic disposal. All major vehicle manufacturers worldwide use bioplastics and bio-based plastics, including natural-fiber composites and engineering plastics reinforced with natural fibers. Changing the source of plastics to raw materials from renewable resources is the logical approach to sustainability. Thus, high-quality plastics, recycled plastics, bio-based plastics, and biodegradable plastics could be exploited from design, making sustainability an integral concept of mobility development. This review analyzes that switching from fossil-fuel- to renewable-sources-derived plastics is a step toward meeting the current environmental goals for the automotive industry, including electric cars.

polymer science
Challenges and Alternatives to Plastics Recycling in the Automotive Sector

Lindsay Miller,Katie Soulliere,Susan Sawyer-Beaulieu,Simon Tseng,Edwin Tam

DOI: https://doi.org/10.3390/ma7085883

IF: 3.4

2014-08-15

Materials

Abstract:Plastics are increasingly a preferred material choice in designing and developing complex, consumer products, such as automobiles, because they are mouldable, lightweight, and are often perceived to be highly recyclable materials. However, actually recycling the heterogeneous plastics used in such durable items is challenging, and presents very different scenarios to how simple products, such as water bottles, are recovered via curbside or container recycling initiatives. While the technology exists to recycle plastics, their feasibility to do so from high level consumer or industrial applications is bounded by technological and economical restraints. Obstacles include the lack of market for recyclates, and the lack of cost efficient recovery infrastructures or processes. Furthermore, there is a knowledge gap between manufacturers, consumers, and end-of-life facility operators. For these reasons, end-of-life plastics are more likely to end up down-cycled, or as shredder residue and then landfilled. This paper reviews these challenges and several alternatives to recycling plastics in order to broaden the mindset surrounding plastics recycling to improve their sustainability. The paper focuses on the automotive sector for examples, but discussion can be applied to a wide range of plastic components from similarly complex products.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Mechanical and chemical recycling of solid plastic waste

Kim Ragaert,Laurens Delva,Kevin Van Geem

DOI: https://doi.org/10.1016/j.wasman.2017.07.044

IF: 8.816

2017-11-01

Waste Management

Abstract:This review presents a comprehensive description of the current pathways for recycling of polymers, via both mechanical and chemical recycling. The principles of these recycling pathways are framed against current-day industrial reality, by discussing predominant industrial technologies, design strategies and recycling examples of specific waste streams. Starting with an overview on types of solid plastic waste (SPW) and their origins, the manuscript continues with a discussion on the different valorisation options for SPW. The section on mechanical recycling contains an overview of current sorting technologies, specific challenges for mechanical recycling such as thermo-mechanical or lifetime degradation and the immiscibility of polymer blends. It also includes some industrial examples such as polyethylene terephthalate (PET) recycling, and SPW from post-consumer packaging, end-of-life vehicles or electr(on)ic devices. A separate section is dedicated to the relationship between design and recycling, emphasizing the role of concepts such as Design from Recycling. The section on chemical recycling collects a state-of-the-art on techniques such as chemolysis, pyrolysis, fluid catalytic cracking, hydrogen techniques and gasification. Additionally, this review discusses the main challenges (and some potential remedies) to these recycling strategies and ground them in the relevant polymer science, thus providing an academic angle as well as an applied one.

environmental sciences,engineering, environmental
Practicality of physical recycling method for waste polymer composites exampled via high density polyethylene/automobile shredder residue composites

Yuanzhang Bai,Kaixuan Song,Yucheng Hou,Ning Chen,Yijun Li

DOI: https://doi.org/10.1002/eng2.12655

2023-03-28

Engineering Reports

Abstract:Physical recycling provides a feasible application route for the recycling of waste polymer. With the booming of automobiles industry, the recycling of automobile shredder residue (ASR) with complicated constitutes gradually become an urgent issues owing to its difficulty for traditional recycling. Herein, solid‐state shear milling (S3M) technology which can control the domain size of the various polymers in blend was applied to overcome the mismatch of viscosity and poor compatibility of ASR and thus modify the processability to match practical manufacturing. Resultantly, the melt processing of ASR was achieved and a high‐density polyethylene (HDPE)/ASR composite was also prepared with more optimal mechanical properties (tensile strength: 53.2 MPa, impact strength: 36.9 kJ/m2), compared with commercially available recycled PE. This work not only provided a feasible application route for the recycling of ASR material, but also demonstrated the optional methodology for recycling polymer waste with complicated component via physical recycling way.
Economic and environmental assessment of automotive plastic waste end‐of‐life options: Energy recovery versus chemical recycling

Christoph Stallkamp,Malte Hennig,Rebekka Volk,Frank Richter,Britta Bergfeldt,Salar Tavakkol,Frank Schultmann,Dieter Stapf

DOI: https://doi.org/10.1111/jiec.13416

2023-07-13

Journal of Industrial Ecology

Abstract:Most automotive plastic waste (APW) is landfilled or used in energy recovery as it is unsuitable for high‐quality product mechanical recycling. Chemical recycling via pyrolysis offers a pathway toward closing the material loop by handling this heterogeneous waste and providing feedstock for producing virgin plastics. This study compares chemical recycling and energy recovery scenarios for APW regarding climate change impact and cumulative energy demand (CED), assessing potential environmental advantages. In addition, an economic assessment is conducted. In contrast to other studies, the assessments are based on pyrolysis experiments conducted with an actual waste fraction. Mass balances and product composition are reported. The experimental data is combined with literature data for up‐ and downstream processes for the assessment. Chemical recycling shows a lower net climate change impact (0.57 to 0.64 kg CO2e/kg waste input) and CED (3.38 to 4.41 MJ/kg waste input) than energy recovery (climate change impact: 1.17 to 1.25 kg CO2e/kg waste input; CED: 6.94 to 7.97 MJ/kg waste input), while energy recovery performs better economically (net processing cost of −0.05 to −0.02€/kg waste input) compared to chemical recycling (0.05 to 0.08€/kg waste input). However, chemical recycling keeps carbon in the material cycle contributing to a circular economy and reducing the dependence on fossil feedstocks. Therefore, an increasing circularity of APW through chemical recycling shows a conflict between economic and environmental objectives.

environmental sciences,green & sustainable science & technology,engineering, environmental
Chemical recycling of plastic waste for sustainable polymer manufacturing – A critical review

Gerardo Martínez-Narro,Samaila Hassan,Anh N. Phan

DOI: https://doi.org/10.1016/j.jece.2024.112323

IF: 7.7

2024-04-01

Journal of Environmental Chemical Engineering

Abstract:Chemical recycling has emerged as a promising approach to valorise non-recyclable, rejected, multi-layer, and contaminated plastic waste streams, such as packaging waste, aligning with the 3R's principles (reduce, reuse, and recycle). This paper critically evaluates various chemical recycling technologies, including pyrolysis, gasification, hydrothermal, and biological methods, which hold the potential to amend the global plastic pollution crisis while recovering valuable materials. Despite the potential of these methods, substantial challenges persist, including technological limitations, elevated capital costs, feedstock variability, energy consumption, and poor regulatory frameworks. The challenges and opportunities for future development are thoroughly discussed. Continuous research and development are vital for advancing chemical recycling technologies and transitioning towards a circular economy. A holistic approach, integrating not only chemical recycling, but also waste reduction, reuse, and other waste management strategies, is required to resolve the plastic waste crisis, and attain a more sustainable future.

engineering, chemical, environmental
From plastic waste to wealth using chemical recycling: A review

Jie Jiang,Ke Shi,Xiangnan Zhang,Kai Yu,Hong Zhang,Jing He,Yun Ju,Jilin Liu

DOI: https://doi.org/10.1016/j.jece.2021.106867

IF: 7.7

2022-02-01

Journal of Environmental Chemical Engineering

Abstract:Global plastic waste has grown at an alarming rate for decades. However, the traditional landfill and incineration treatments may cause air pollution and valuable land squander. From the perspective of sustainability, researchers have tried to recycle plastic waste by mechanical, biological and chemical approaches. Compared with mechanical and biological methods, chemical recycling has attracted more attention because it can selectively convert the plastic waste into high-value products including refinery feedstock, fuel and monomer. According to types of solvent, catalyst and product, chemical recycling can be further divided into solvolysis, pyrolysis, and gasification. This review highlighted the recent achievements of these chemical recycling technologies. The close link between the final products and reaction conditions, such as the reactor type, catalyst, and reaction temperature were described in detail. Meanwhile, the environmental performance and influence of chemical recycling were systematically evaluated. Finally, the challenges and future trends in chemical recycling of plastic waste are proposed. These insights will offer guidance for the development of industrial-relevant catalysts and recycling systems.

engineering, chemical, environmental
Small-Scale Mechanical Recycling of Solid Thermoplastic Wastes: A Review of PET, PEs, and PP

Canice C. Uzosike,Lachlan H. Yee,Ricardo Vasquez Padilla

DOI: https://doi.org/10.3390/en16031406

IF: 3.2

2023-02-01

Energies

Abstract:The mechanical recycling of solid plastic waste on a small-scale level can be accomplished with the correct approaches. Thermoplastics are the types of plastic mostly considered for mechanical recycling because of their physical properties and ease of reprocessing. This paper reviews the mechanical reprocessing techniques of selected thermoplastics (polyethylene terephthalate and polyolefins), since they constitute a significant proportion of the plastics used commercially. Furthermore, necessary considerations for the effective operation of small-scale plants, including energy requirements of machinery and optimisation in order to improve efficiency and product quality, are discussed. A clearer understanding and addressing of the process-related challenges will lead to the successful establishment and management of small-scale mechanical recycling facilities to benefit communities. Efficient small-scale mechanical reprocessing establishments have become essential in reducing the environmental impacts of solid plastic waste and for energy conservation.

energy & fuels
A technology review of recycling methods for fiber-reinforced thermosets

Xiao Xue,Shu-Yan Liu,Zhao-Yang Zhang,Qing-Zhou Wang,Cheng-Zhi Xiao

DOI: https://doi.org/10.1177/07316844211055208

IF: 3.1

2021-11-19

Journal of Reinforced Plastics and Composites

Abstract:The rapidly rising demand for fiber-reinforced plastics (FRPs) has led to large volumes of manufacturing and end-of-life waste. Recycling fiber-reinforced thermosets is very difficult owing to their complex structure and heterogeneity. Landfill and incineration have become the most commonly used methods for eliminating non-degradable FRP waste, which adversely affects the environment and ecology. The purpose of this review is to evaluate end-of-life FRP recycling technologies in terms of optimizing the reuse/recycling of resources and eliminating waste, thereby improving FRP waste management. The technical progress made in the recycling of thermosetting composites is reviewed, including mechanical, thermal (pyrolysis and fluidized-bed), and chemical (critical fluid and low-temperature solvent) methods. The technical feasibility of each method was compared, and the economic and environmental impacts were considered. The challenges and opportunities facing the establishment of a composite recycling market in the future are examined. Finally, we provide a comprehensive summary of the scope of each recycling method.

materials science, composites,polymer science
Mechanical Recycling of New and Challenging Polymer Systems: A Brief Overview

Vincenzo Titone,Luigi Botta,Francesco Paolo La Mantia

DOI: https://doi.org/10.1002/mame.202400275

2024-11-07

Macromolecular Materials and Engineering

Abstract:This review addresses advancements and challenges in the mechanical recycling of new and challenging polymer systems. It highlights the less‐explored topic of recycling of mixed plastic of oil‐derived polymers, multilayer packaging, biodegradable polymer system and discusses their potential applications. The review aims to provide an updated perspective on the integration of new polymer systems and recycling techniques. Pollution from plastics is a major issue in the current context, prompting the scientific community to focus its efforts on recycling these materials. Mechanical recycling emerges as the most popular due to its practicality and cost‐effectiveness. In fact, with the increase in environmental awareness, the adoption of new circular economy models, stricter regulations mandating disposal and recycling, and lower costs compared to other recycling techniques, this type of recycling is taking a predominant role over other method. However, the presence of a variety of products of different polymeric nature, the introduction of new biodegradable products, and the complexity of multilayer packaging combining different polymers, without concrete solutions for recycling create a heterogeneous range of materials that leaks into the environment. The scientific literature is actively addressing these challenges, and this review aims to explore the latest strategies for enhancing the mechanical recycling of new and challenging polymer systems. Specifically, it explores the recycling of materials originally designated for landfill, incineration or composting, focusing on advancements in management of these previously overlooked and problematic system. This underexplored perspective seeks to offer new insights and innovative solutions that can transform polymer waste management and advance more sustainable recycling practices.

materials science, multidisciplinary,polymer science
Is the assimilation to a solid recovered fuel a viable solution for automobile shredder residues’ management?

Barbara Ruffino,Mariachiara Zanetti

DOI: https://doi.org/10.1016/j.envres.2024.118131

IF: 8.3

2024-04-01

Environmental Research

Abstract:Directive 2000/53/EC and the European Circular Economy Package (2018) required the Member States to take all the necessary measures to reach the reuse-recycling goal of 85% for end-of-life vehicles (ELVs). In 2019, Europe achieved 89.6% of reuse-recycling, but most EC countries are still not completely compliant, Italy standing, for example, at only 84.2%. For this reason, actions are necessary to increase reuse-recycling for the waste generated in the operations of ELV shredding and separation, known as automobile shredded residues (ASRs). This study was aimed at assessing if the assimilation of ASRs to a solid recovered fuel (SRF) was a feasible solution. That would allow the waste to lose its status (end-of-waste, EoW), thus increasing the recycling rate. The assimilation of ASRs to SRFs requires the compliance with a series of parameters, namely net calorific value (NCV), content of chlorine (Cl), mercury (Hg) and selected heavy metals. The above-mentioned parameters were analyzed in the principal ASR fractions, namely textile, plastic and foam rubber, found in the samples collected during four sampling campaigns (2017-2021) performed at the same ELV treatment plant. Notwithstanding the great variability observed in the four samples, the results of the analyses revealed that the three fractions were compliant with NCV, Cl and Hg content. Conversely, the heavy metals' content was found a more critical parameter, in fact only the plastic fraction was suitable for SRF assimilation. Textiles presented criticality for the content of copper (Cu), nickel (Ni) and antimony (Sb). The heavy metals' contamination of foam rubber was found to be strongly related to particles' dimensions. A model which put particle size and metals' content into relationship was developed and validated. Removing particles of <40 mm significantly improved the quality of the material, however the content of Cu and Ni remained a critical issue for particles up to 200 mm. The SRF assimilation of the plastic fraction would increase the reuse-recycling rate of approx. 2.4-3.3%, thus allowing the achievement of the EC goals concerning the ELV management.

environmental sciences,public, environmental & occupational health
Mechanothermal and chemical recycling methodologies for the Fibre Reinforced Plastic (FRP)

Swaroop Gharde,Balasubramanian Kandasubramanian

DOI: https://doi.org/10.1016/j.eti.2019.01.005

2019-05-01

Abstract:Materials have become an integral part of our lives owing to their wide usability, but at the same time, they are affecting the nature antithetically. Fibre Reinforced Plastic (FRP) is highly sought materials in an automobile, aerospace, structural, transportation and other industries due to its excellent mechanical performance, durability, and lightweight. Currently, miscellaneous industries manufacture engineered composite products using FRP materials, especially the products of hardbound thermoset resins, which are difficult to reprocess or reuse. Landfills and incineration are the most common technique for discarding the non-degradable FRP waste that has created an inimical impact on the environment and ecosystem. In order to reduce the ecological burden, we need to evaluate economical and feasible FRP recycling techniques. Extensive investigations conducted over the past decades have proven their efficacy in substituting the currently existing recycling processes. This review article enumerates the mechanical, thermal (fluidised bed and pyrolysis), chemical (low temperature and supercritical temperature) recycling methodologies, and their efficiency in degrading copious FRP materials like glass, carbon, natural etc. In addition, the economic and environmental aspects of fibre reinforced plastic materials based on life cycle assessment (LCA) has been discussed.

environmental sciences,engineering, environmental,biotechnology & applied microbiology
Recycling and Material-Flow Analysis of End-of-Life Vehicles towards Resource Circulation in South Korea

Yong-Chul Jang,Kyunghoon Choi,Ji-hyun Jeong,Hyunhee Kim,Jong-Guk Kim

DOI: https://doi.org/10.3390/su14031270

IF: 3.9

2022-01-24

Sustainability

Abstract:The sustainable resource management of end-of-life vehicles (ELVs) towards a circular economy has become an issue of concern around the world. An understanding of recycling and the quantitative flow of ELVs is important because of their potential for resource recovery as well as the environmental impacts posed by their toxic chemicals upon disposal. In this paper, the generation and recycling system of ELVs in South Korea has been discussed based on a review of the available statistics and literature and site visits to ELV-recycling facilities. A material-flow analysis (MFA) for ELVs was performed to elucidate the resource recovery from recycling, while the substance flow of polybrominated diphenyl ethers (PBDEs) in automobile shredded residues (ASR) was also determined for proper management. Approximately one million tons of ELVs in 2020 were processed by dismantling and shredding treatment for the recovery of reusable and recyclable materials (803,000 tons), resulting in 78,300 tons of ASR. Approximately 97 tons of PBDEs as flame retardants were generated mainly from ASR in 2020 and processed via combustion, either with energy recovery (59.8%) or without heat recovery (39.2%). The monitoring of brominated dioxins and furans by unintentional release during the incineration processes of ASR is required in order to prevent the dispersion of the chemicals in the environment.

environmental sciences,environmental studies,green & sustainable science & technology
Waste Plastics Chemical Recycling in the Context of Refining and Petrochemical Industries

Tarig Hussein,Daniel Maxa

DOI: https://doi.org/10.35933/paliva.2023.04.01

2023-12-31

Paliva

Abstract:Rising demand for plastic materials results in increasing volumes of plastic waste generated globally. This poses a question of waste collection and handling of the growing waste volumes. With quality limitations of reuse and mechanical recycling, especially end-of-life mixed plastic waste is mostly landfilled, incinerated or lost to environment. Thermochemical recycling, especially pyrolysis, has been historically explored as an attractive alternative waste processing method with a potential to valorise the plastic waste into energy, fuels and more recently also chemicals and virgin polymers. Thermochemical plastic waste processing and treatment of the intermediates towards the final products have been found to be studied mostly in isolation. Therefore, this study provides a combined view. Updated state of pilot and demonstration projects is reviewed. Typical characteristics of plastic waste pyrolysis products are introduced and the areas of potential impacts on existing plants are highlighted. In order to address the circularity and economic aspect, a summary of recent relevant LCA and business studies is provided, showing common sensitivity factors and main assumptions used therein. Overall, this review summarizes the background behind the recycling of waste plastics and presents it in context of challenges and opportunities of integration with existing refining and petrochemical infrastructure.
Solvent-based Separation and Recycling of Waste Plastics: A Review

Yi-Bo Zhao,Xu-Dong Lv,Hong-Gang Ni

DOI: https://doi.org/10.1016/j.chemosphere.2018.06.095

IF: 8.8

2018-01-01

Chemosphere

Abstract:Since the creation of first man-made plastic, the global production and consumption of plastics have been continuously increasing. However, because plastic materials are durable and very slow to degrade, they become waste with high staying power. The over-consumption, disposal, and littering of plastics result in pollution, thus causing serious environmental consequences. To date, only a fraction of waste plastics is reused and recycled. In fact, recycling plastics remains a great challenge because of technical challenges and relatively insufficient profits, especially in mixed plastics. This review focuses on an environmentally friendly and potentially profitable method for plastics separation and recovery and solvents extraction. It includes the dissolution/reprecipitation method and supercritical fluid extraction, which produce high-quality recovered plastics comparable to virgin materials. These methods are summarized and discussed taking mass-produced plastics (PS, PC, Polyolefins, PET, ABS, and PVC) as examples. To exploit the method, the quality and efficiency of solvent extraction are elaborated. By eliminating these technical challenges, the solvent extraction method is becoming more promising and sustainable for plastic issues and polymer markets.
Long-term sickness absence from work due to physical inactivity: A registry-based study

Cecilie Høgsbro,M. Davidsen,J. Sørensen

DOI: https://doi.org/10.1177/1403494817751328

2018-01-24

Scandinavian Journal of Public Health

Abstract:Aims: The aim of this study was to explore the relationship between leisure-time physical inactivity and long-term sickness absence in a representative sample of individuals aged 16–54 years, within the labour market and in good health. It was hypothesised that physically inactive individuals have a higher risk of long-term sickness absence and longer duration of sickness absence. Methods: The study population was identified from the National Health and Morbidity Survey, 2010. Weekly data on long-term sickness absence were obtained from the National Register on Social Transfer Payments (the DREAM registry). The association of incidence and duration of long-term sickness absence with physical inactivity was explored using logistic and Poisson regression. Data were fitted to models with levels of physical activity, demographic, social and lifestyle characteristics as independent variables. A combined hurdle model was used to estimate the difference in mean number of absence weeks. Results: Logistic regression showed that physically inactive individuals had a 27% higher incidence of long-term sickness absence compared with physically active individuals. The Poisson regression showed that long-term sickness absence was only slightly shorter (1 week less) for moderately active individuals compared with inactive individuals. The hurdle model estimated longer absence periods for inactive individuals (additional 2.5 weeks) in comparison with moderately and highly active individuals. Conclusions: The study showed that physically inactive individuals have a higher incidence of long-term absence and that physically inactive individuals have longer periods with sickness absence than moderately and highly active individuals. When adjustments for social and health behaviour were included, the estimated associations became statistically insignificant.
Thermal and Catalytic Recycling of Plastics from Waste Electrical and Electronic Equipment-Challenges and Perspectives

Dimitris S Achilias,Maria-Anna Charitopoulou,Stefano Vecchio Ciprioti

DOI: https://doi.org/10.3390/polym16172538

2024-09-07

Abstract:The amount of end-of-life electrical and electronic devices has been widely increased, globally. This emphasizes how recycling waste electric and electronic equipment (WEEE) is essential in order to reduce the amount of WEEE that is disposed of directly in the environment. Plastics account for a big percentage in WEEE, almost 20%. As a result, the application of recycling methods on plastics gathered from WEEE is of great importance since, in this way, landfill disposal can be reduced. Nevertheless, despite the advantages, there are a lot of difficulties, such as the variety of different plastics present in the plastic mix and the existence of various additives in the plastic parts, for instance, brominated flame retardants that need special attention during their treatments, which restricts their wide application. Considering all these, this review aims to provide readers with all the current techniques and perspectives that are available for both the thermal and the catalytic recycling of plastics retrieved from WEEE. Apart from the up-to-date information on the recycling methods, in this review, emphasis is also given on the advantages each method offers and also on the difficulties and the limitations that may prevent them from being applied on a large scale. Current challenges are critically examined, including the use of mechanical or thermo-chemical recycling, the treatment of individual polymers or polymer blends and the separation of harmful additives before recycling or not. Finally, emerging technologies are briefly discussed.
Mechanical Recycling of Packaging Plastics: A Review.

Zoé O G Schyns,M. Shaver

DOI: https://doi.org/10.1002/marc.202000415

IF: 5.006

2020-09-30

Macromolecular Rapid Communications

Abstract:The current global plastics economy is highly linear, with the exceptional performance and low carbon footprint of polymeric materials at odds with dramatic increases in plastic waste. Transitioning to a circular economy that retains plastic in its highest value condition is essential to reduce environmental impacts, promoting reduction, reuse, and recycling. Mechanical recycling is an essential tool in an environmentally and economically sustainable economy of plastics, but current mechanical recycling processes are limited by cost, degradation of mechanical properties, and inconsistent quality products. This review covers the current methods and challenges for the mechanical recycling of the five main packaging plastics: poly(ethylene terephthalate), polyethylene, polypropylene, polystyrene, and poly(vinyl chloride) through the lens of a circular economy. Their reprocessing induced degradation mechanisms are introduced and strategies to improve their recycling are discussed. Additionally, this review briefly examines approaches to improve polymer blending in mixed plastic waste streams and applications of lower quality recyclate.

Medicine,Environmental Science,Materials Science

Ketoconazole promotes parasitological cure of mice infected with Trypanosoma cruzi.

Recycling of Plastics in the Automotive Sector and Methods of Removing Paint for Its Revalorization: A Critical Review

Challenges around automotive shredder residue production and disposal

Engineering, Recyclable, and Biodegradable Plastics in the Automotive Industry: A Review

Challenges and Alternatives to Plastics Recycling in the Automotive Sector

Mechanical and chemical recycling of solid plastic waste

Practicality of physical recycling method for waste polymer composites exampled via high density polyethylene/automobile shredder residue composites

Economic and environmental assessment of automotive plastic waste end‐of‐life options: Energy recovery versus chemical recycling

Chemical recycling of plastic waste for sustainable polymer manufacturing – A critical review

From plastic waste to wealth using chemical recycling: A review

Small-Scale Mechanical Recycling of Solid Thermoplastic Wastes: A Review of PET, PEs, and PP

A technology review of recycling methods for fiber-reinforced thermosets

Mechanical Recycling of New and Challenging Polymer Systems: A Brief Overview

Is the assimilation to a solid recovered fuel a viable solution for automobile shredder residues’ management?

Mechanothermal and chemical recycling methodologies for the Fibre Reinforced Plastic (FRP)

Recycling and Material-Flow Analysis of End-of-Life Vehicles towards Resource Circulation in South Korea

Waste Plastics Chemical Recycling in the Context of Refining and Petrochemical Industries

Solvent-based Separation and Recycling of Waste Plastics: A Review

Long-term sickness absence from work due to physical inactivity: A registry-based study

Thermal and Catalytic Recycling of Plastics from Waste Electrical and Electronic Equipment-Challenges and Perspectives

Mechanical Recycling of Packaging Plastics: A Review.