Employing Data Driven Random Membership Subset Algorithm for QoS-Aware Peer-to-Peer Streaming

Y. Huang,D. Qian,Weiguo Wu,Hai-ying Zhao

DOI: https://doi.org/10.1007/978-3-642-02472-6_8

Abstract:

What problem does this paper attempt to address?

Solvent Vapor Annealing of Ferroelectric P(VDF-TrFE) Thin Films

Jinghang Hu,Jianchi Zhang,Zongyuan Fu,Yulong Jiang,Shijin Ding,Guodong Zhu

DOI: https://doi.org/10.1021/am5055299

IF: 9.5

2014-01-01

ACS Applied Materials & Interfaces

Abstract:Ferroelectric polymers are a kind of promising materials for low-cost flexible memories. However, the relatively high thermal annealing temperature restricts the selection of some flexible polymer substrates. Here we report an alternative method to obtain ferroelectric poly(vinylidenefluoride-co-trifluoroethylene) (P(VDF-TrFE)) thin films under low process temperatures. Spin-coated P(VDF-TrFE) thin films were solvent vapor processed at 30 °C for varied times. Structural analyses indicated that solvent vapor annealing induced crystallization to form a ferroelectric β phase, and electrical measurements from both macroscopic ferroelectric switching and microscopic vertical piezoresponse force microscopy further proved the films enduring solvent vapor annealing for suitable short times possessed good ferroelectric and piezoelectric properties. To illuminate the application of solvent vapor annealing on ferroelectric devices, we further fabricated ferroelectric capacitor memory devices with a structure of Al/P(VDF-TrFE)/Al2O3/p-Si/Al where the ferroelectric layer was solvent vapor annealed. Ferroelectric capacitors showed obvious bistable operation and comparable ON/OFF ratio and retention performance. Our work makes it possible to structure ferroelectric devices on flexible substrates that require low process temperatures.
Improved Thermal Stability of Ferroelectric Phase in Epitaxially Grown P(VDF-TrFE) Thin Films

Zongyuan Fu,Wei Xia,Weibo Chen,Junhui Weng,Jian Zhang,Jianchi Zhang,Yulong Jiang,Guodong Zhu

DOI: https://doi.org/10.1021/acs.macromol.6b00532

IF: 5.5

2016-01-01

Macromolecules

Abstract:In recent years ferroelectric polymers have attracted much attention due to their potentials in flexible electronics. To satisfy the requirements of low operation voltage and low power consumption, it is required to reduce the ferroelectric film thickness down to, for example, 100 nm. However, decreased film thickness results in low crystallinity and thus worse electrical performance. One possible solution is to realize the epitaxial growth of ferroelectric thin films via effective control of structure and orientation of ferroelectric crystals. Here we report our work on poly(tetrafluoroethylene)-template-induced ordered growth of ferroelectric thin films. We focus on the study of thermal stability of ferroelectric phase in these ferroelectric films. Our work indicates that epitaxial growth effectively increases the crystallinity and the melting and ferroelectric phase transition temperatures and implies the extended application of ferroelectric devices at higher temperature.
Unveiling the piezoelectric nature of polar α-phase P(VDF-TrFE) at quasi-two-dimensional limit

Jun Qian,Sai Jiang,Qijing Wang,Shushu Zheng,Shuya Guo,Chang Yi,Jianpu Wang,Xinran Wang,Kazuhito Tsukagoshi,Yi Shi,Yun Li

DOI: https://doi.org/10.1038/s41598-017-18845-2

IF: 4.6

2018-01-01

Scientific Reports

Abstract:Piezoelectric response of P(VDF-TrFE), which is modulated by the dipole density due to the polarization switching on applying an electric field, allows it act as the fundamental components for electromechanical systems. As proposed since the 1970s, its polar α-phase is supposed to yield an enhanced piezoelectric activity. However, its experimental verification has never been reported, hampered by a substantial challenge for the achievement of a smooth, neat α-phase film. Here, we prepare ultrathin crystalline α-phase P(VDF-TrFE) films on the AlO x /Al-coated SiO 2 /Si substrates via a solution-based approach at room temperature. Thus, we unveil the piezoelectric nature of the polar α-phase P(VDF-TrFE) at a quasi-two-dimensional limit. The obtained values of the relative morphological deformation, the local effective piezoelectric coefficient, and the electric field-induced strain reach up to 37 pm, −46.4 pm V −1 , and 4.1%, respectively. Such a robust piezoelectric response is even higher than that of the β-phase. Besides, the evolution of piezoelectricity, which is related to the piezoelectric properties of two polarization states, is also studied. Our work can enable the exploration of the prospective applications of polar α-phase P(VDF-TrFE) films.
Temperature Control of P(Vdf-Trfe) Copolymer Thin Films

Tingting Feng,Dan Xie,Yongyuan Zang,Xiao Wu,Tianling Ren,Wei Pan

DOI: https://doi.org/10.1080/10584587.2012.694748

2013-01-01

Integrated Ferroelectrics

Abstract:Ferroelectric poly(vinylidene fluoride-trifluoroethylene) [P(VDF-TrFE)] (70/30) copolymer thin films were prepared by spin-coating method. The microstructure and morphology of P(VDF-TrFE) thin films annealed at different temperatures (70 degrees C-160 degrees C) were investigated by atom force microscope and X-ray diffraction techniques, which reveal the crystallization of P(VDF-TrFE) films is greatly affected by the annealing temperature. With the increase of annealing temperature, the grains of P(VDF-TrFE) thin film change from small spheroids to long needle-like structures. The most rapid change occurs between 136 degrees C-140 degrees C. The surface roughness and the grain size of P(VDF-TrFE) film show similar change with the annealing temperature.
Microstructural influence on thermal stability of ferroelectric properties in P(VDF-TrFE) spin cast thin films

Davide Disnan,Fabian Bacher,Stephan Berger,Michael Schneider,Ulrich Schmid

DOI: https://doi.org/10.1016/j.polymer.2024.126894

IF: 4.6

2024-04-01

Polymer

Abstract:Ferroelectric polymers, like poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)), find applications across various fields due to their unique mechanical and electrical properties. This study investigates the impact of thermal loading up to 90 °C on the ferroelectric characteristics of two distinct microstructures, spherulite-like and rice-like, formed during the thermal annealing after deposition of P(VDF-TrFE) thin films. Thermal cycles revealed a reduced ferroelectric activity in spherulite-like sample, in contrast to the ferroelectric stability observed in the rice-like counterparts. XRD analyses indicate that this behaviour is due to a crystalline phase stabilization of the γ-2b phase in the spherulite-like thin films. Furthermore, energy characteristics investigations highlighted a better performance of the pristine spherulite-like compared to the rice-like microstructure. All in all, despite these performance differences, our findings remark that careful considerations are needed in potential applications of P(VDF-TrFE) thin films where reliability and precision across a wide range of operating temperatures are required.

polymer science
Direct observation of room-temperature out-of-plane ferroelectricity and tunneling electroresistance at the two-dimensional limit

H. Wang,Z. R. Liu,H. Y. Yoong,T. R. Paudel,J. X. Xiao,R. Guo,W. N. Lin,P. Yang,J. Wang,G. M. Chow,T. Venkatesan,E. Y. Tsymbal,H. Tian,J. S. Chen

DOI: https://doi.org/10.1038/s41467-018-05662-y

IF: 16.6

2018-01-01

Nature Communications

Abstract:Out-of-plane ferroelectricity with a high transition temperature in nanometer-scale films is required to miniaturize electronic devices. Direct visualization of stable ferroelectric polarization and its switching behavior in atomically thick films is critical for achieving this goal. Here, ferroelectric order at room temperature in the two-dimensional limit is demonstrated in tetragonal BiFeO 3 ultrathin films. Using aberration-corrected scanning transmission electron microscopy, we directly observed robust out-of-plane spontaneous polarization in one-unit-cell-thick BiFeO 3 films. High-resolution piezoresponse force microscopy measurements show that the polarization is stable and switchable, whereas a tunneling electroresistance effect of up to 370% is achieved in BiFeO 3 films. Based on first-principles calculations and Kelvin probe force microscopy measurements, we explain the mechanism of polarization stabilization by the ionic displacements in oxide electrode and the surface charges. Our results indicate that critical thickness for ferroelectricity in the BiFeO 3 film is virtually absent, making it a promising candidate for high-density nonvolatile memories.
Tuned Dielectric, Pyroelectric and Piezoelectric Properties of Ferroelectric P(Vdf-Trfe) Thin Films by Using Mechanical Loads

G. Bai,R. Li,Z. G. Liu,Y. D. Xia,J. Yin

DOI: https://doi.org/10.1063/1.3685750

IF: 2.877

2012-01-01

Journal of Applied Physics

Abstract:Using the phenomenological Landau thermodynamic theory, we have investigated the effect of external mechanical loads on the phase transition and physical properties of poly(vinylidene fluoride-trifluorethylene) [P(VDF-TrFE)] thin films. Quantitative calculation shows that the phase transition temperature, polarization, dielectric, pyroelectric, and piezoelectric properties are highly sensitive to external mechanical loads. External compressive stress increases the phase transition temperature and the out-of-plane polarization and decreases the out-of-plane dielectric constant below Tc, pyroelectric coefficient, and piezoelectric coefficient (absolute value) and vice versa. Compared with pervoskite-type ferroelectrics, the calculated results are opposite due to the different intrinsic parameters between pervoskite and polymer ferroelectrics, especially, electrostrictive constants. The ability to tailor the properties in ferroelectric P(VDF-TrFE) thin films with the mechanical load can offer a tremendously promising future for applications in multifunctional devices, such as agile mechanical sensors and transducers.
Crystallisation behaviours of ferroelectric P(VDF-TrFE) ultrathin films on different substrates

changchun wang,qundong shen,bo kou

DOI: https://doi.org/10.1179/1432891715Z.0000000001553

2015-01-01

Materials Research Innovations

Abstract:A series of ferroelectric polymer ultrathin films on different substrates were fabricated by spin coating. Thickness of the ultrathin films was easy to manipulate through tuning the polymer concentration or spin-coating speed. Crystallisation behaviours of these ferroelectric films on different substrates such as bare silicon, silicon coated with Cr or Au, were investigated by atomic force microscopy. The substrates had remarkable effect on the morphologies of the ferroelectric ultrathin films after annealing. Ferroelectric polymer ultrathin film on bare silicon grew to lamellar crystals, while the ultrathin film on silicon coated with Au came into being 'ball-like' crystals which were aggregated by smaller ones. The crystallisation behaviour of ferroelectric ultrathin film on silicon coated with Cr was closely related with its heat history. The film annealed immediately after fabrication generated rodlike crystals, which connected with each other. However, the one annealed after storage for a week in desiccator created spherulites, and these spherulites collided with each other and generated curved lamellae which were twisted. The different crystallisation behaviours of the ultrathin films may be due to the surface energy of different substrates. Moreover, P(VDF-TrFE) ultrathin film showed ferroelectricity although its thickness is about 10 nm.
Optimization of electro-strain and ferroelectric properties of P(VDF-TrFE) films under the synergistic effect of PTO nanosheets and in-situ electrostatic field

Kaiqi Zhu,Fu Lv,Jiamin Lin,Zijian Hong,Yongjun Wu,Yuhui Huang

DOI: https://doi.org/10.1016/j.jmat.2024.100963

IF: 8.589

2024-11-18

Journal of Materiomics

Abstract:Highlights • The negative strain properties of P(VDF-TrFE) films have been verified and further modulated by incorporating PTO nanosheets. • Electro-strain and ferroelectric properties were enhanced by combined effect of nanosheets and in-situ electrostatic field. • A possible mechanism has been proposed, which is attributed to the flexibility of amorphous phase and content of β-phase. Traditional ferroelectric materials, such as lead zirconate titanate (PZT) ceramics, exhibit positive strain when subjected to an electric field along the polarization direction. In contrast, the piezoelectric polymer polyvinylidene fluoride (PVDF) and its copolymer P(VDF-TrFE) display unique negative strain properties. While extensive research has focused on understanding the origin and mechanisms of this negative strain, limited efforts have been directed toward regulating these properties. This study optimizes the electro-strain and ferroelectric properties of P(VDF-TrFE) piezoelectric films through the synergistic effect of PbTiO 3 nanosheets and an in-situ electrostatic field. Our results demonstrate that while the incorporation of PbTiO 3 nanosheets does not notably enhance ferroelectricity, it significantly improves electro-strain properties, particularly negative strain, which increases from –0.097% to –0.185%, an enhancement of 91%. Moreover, the ferroelectric polarization and positive strain of P(VDF-TrFE) are further enhanced under the combined influence of PbTiO 3 nanosheets and in-situ electrostatic field, increasing maximum polarization from 10.79 μC/cm 2 to 13.16 μC/cm 2 , a 22% improvement, and positive strain from 0.213% to 0.267%, a 25% enhancement. We propose a possible mechanism for these improvements, attributed to the enhanced flexibility of the amorphous phase and increased content of polar β-phase in P(VDF-TrFE) films under this synergistic effect. This work highlights novel strategies for controlling the electro-strain and ferroelectric properties of P(VDF-TrFE) piezoelectric films. Graphical abstract Download: Download high-res image (223KB) Download: Download full-size image

materials science, multidisciplinary,chemistry, physical,physics, applied
Giant Electrocaloric Effect in Ferroelectric Ultrathin Films at Room Temperature Mediated by Flexoelectric Effect and Work Function

Ye Qiu,Huaping Wu,Jie Wang,Jia Lou,Zheng Zhang,Aiping Liu,Takayuki Kitamura,Guozhong Chai

DOI: https://doi.org/10.1063/1.4992811

IF: 2.877

2017-01-01

Journal of Applied Physics

Abstract:In ferroelectric ultrathin films, built-in electric fields are often present due to the flexoelectric effect and the difference of work functions at asymmetric electrodes, which may change the properties of the materials. In this paper, the influence of build-in electric fields induced by flexoelectric effect and/or work function difference on the misfit strain-temperature phase diagrams, and the electrocaloric properties of epitaxial BaTiO3 ultrathin films are investigated by using an extended nonlinear thermodynamic theory. It is found that the flexoelectric effect, i.e., the coupling of polarization and strain gradient, changes the misfit strain-temperature phase diagrams notably, in which the phases with out-of-plane polarizations increase due to the presence of a built-in field. The electrocaloric properties are remarkably enhanced when the built-in fields induced by both the flexoelectric effect and work function difference are considered. In particular, a giant adiabatic temperature change of 7.89 K in ultrathin Pt/BaTiO3/SrRuO3 capacitors at 460 K is predicted. Moreover, it is demonstrated that the peak of adiabatic temperature change versus working temperature is shifted from a high temperature to room temperature, suggesting that ferroelectric ultrathin films with asymmetric electrodes and strain gradient are promising candidates for room temperature refrigeration.
In Situ Observation of the Nanocrystal Growth and Their Piezoelectric Performance Change in P(Vdf-Trfe) Films by Hot Stage Piezoresponse Force Microscopy

Dong Guo,Xiaosui Chen,Xiangcheng Chu,Fei Zeng,Yang Bai,Jiangli Cao,Brahim Dkhil

DOI: https://doi.org/10.1063/1.4801971

IF: 2.877

2013-01-01

Journal of Applied Physics

Abstract:We report the growth process of nanocrystals in spin-coated P(VDF-TrFE) films and the corresponding change in piezoelectric response by using in situ hot stage piezoresponse force microscopy (PFM). Upon annealing, irregularly shaped grains of the as-deposited film gradually grew up, and leaf-shaped grains with rather different piezoelectric response were formed above 120 °C. PFM images indicated that the individual grains in the P(VDF-TrFE) film were highly ordered nanocrystals having uniform molecular orientation, while different nanocrystals might show different molecular orientation. At 150 °C, which is higher than the Curie temperature of the material, the nanocrystals still showed a strong piezoelectric response despite the appearance of melt phase. This reveals a diffused transition in piezoelectric response that is related to the coexistence of crystalline and amorphous phases in the copolymer material. An annealing induced molecular reorientation observed by PFM was also confirmed by other characterization techniques.
Superior Transverse Piezoelectricity in a Halide Perovskite Molecular Ferroelectric Thin Film

Zhong-Xia Wang,Hua Zhang,Fang Wang,Hao Cheng,Wen-Hui He,Yu-Hua Liu,Xue-Qin Huang,Peng-Fei Li

DOI: https://doi.org/10.1021/jacs.0c06064

2020-07-22

Abstract:Piezoelectric materials with inherent mechanical-electric coupling effect are a crucial family of functional materials in high-end information technology. For practical applications, the transverse piezoelectric performance (d31 or d32) is mainly considered, because this parameter is a vitally important index to characterize the performance of piezoelectric thin films. However, the transverse piezoelectricity of the thin films as a key figure of merit is seldom mentioned in molecular ferroelectrics. Herein, we report that a new 1D halide perovskite ferroelectric N,N-dimethylallylammoniumCdCl3 (DMAACdCl3) exhibits an above room-temperature ferroelectric phase transition with a saturated polarization of 1.9 μC cm-2 and a coercive field of 5.0 kV cm-1. The thin film of DMAACdCl3 is successfully fabricated using an easy processing spinning method and maintains well ferroelectric properties verified by piezoresponse force microscopy (PFM). More significantly, the ferroelectric thin film offers superior transverse piezoelectricity with an in-plane piezoelectric response of about 41 pC N-1, which is about twice that of well-known piezoelectric polymer PVDF (21 pC N-1). Transverse piezoelectricity has been scarcely studied in molecular ferroelectrics, and its exploitation would play an important role in the design of next-generation smart piezoelectric devices.
In-situ Electrostatic Field Regulating the Recrystallization Behavior of P(VDF-TrFE) Films with High Β-Phase Content and Enhanced Piezoelectric Properties Towards Flexible Wireless Biosensing Device Applications

Fu Lv,Jiamin Lin,Zheng Zhou,Zijian Hong,Yongjun Wu,Zhaohui Ren,Qilong Zhang,Shurong Dong,Jikui Luo,Junhui Shi,Ruimin Chen,Bing Liu,Yuanjie Su,Yuhui Huang

DOI: https://doi.org/10.1016/j.nanoen.2022.107507

IF: 17.6

2022-01-01

Nano Energy

Abstract:Fabrication of flexible piezoelectric polymers is essential for the development of wearable biosensors. Nevertheless, the piezoelectric coefficient of polymers is usually an order of magnitude lower than the inorganic piezoelectric materials, which limits the miniature of the devices. Herein, a simple and cost-effective technique is proposed by applying an electrostatic field to in-situ regulate the recrystallization behavior of the poly(vinylidene fluoride-trifluorethylene) (P(VDF-TrFE)) film during the thermal annealing and recrystallization stage. Significantly enhanced properties are obtained, including a large piezoelectric coefficient (d 33 ~30.7 pC/N) and a high voltage sensitivity of 167.12 mV/kPa. The outstanding performance is mainly attributed to the applied electrostatic field maintained during the film growth stage, which promotes the generation of nucleation sites for the polar β lamellae crystals. A wireless sensor system is further established with the obtained P(VDF-TrFE) film, demonstrating great potential applications in movement monitoring. The proposed facile approach could potentially be applied to the large-scale production of polymer films with excellent piezoelectric properties for flexible wireless biosensing device applications.
Phase Transitions and Ferroelectric Relaxor Behavior in P(VDF−TrFE−CFE) Terpolymers

Hui-Min Bao,Jiao-Fan Song,Juan Zhang,Qun-Dong Shen,Chang-Zheng Yang,Q. M. Zhang

DOI: https://doi.org/10.1021/ma062800l

IF: 5.5

2007-01-01

Macromolecules

Abstract:We show that the microstructures and phase transition behavior of vinylidene fluoride-trifluoroethylene-chlorofluoroethylene terpolymer, P(VDF-TrFE-CFE), with composition of 61.5/30.3/8.2 mol %, can be varied dramatically via different processing conditions. In the well-annealed sample, the polymer exhibits typical relaxor ferroelectric behavior with the nonpolar crystalline phase having a chain structure of random sequence of TT/TG/TG' conformations. In contrast, by lowering the crystallization temperature in the solution-cast films, the polar crystal phase with all-trans (T-m > 4) planar zigzag conformation (similar to the ferroelectric phase in the corresponding copolymer) can appear or even become a dominating phase. Four types of transitions can be detected in this terpolymer, besides the crystal melting, the glass transition in amorphous region, and the transition between the ferroelectric-like and paraelectric crystals (30-90 degrees C), an additional transition appears near 10 degrees C which can be attributed to the crystalline domains with all-trans sequence randomly disrupted by defects, and the coherence length of these domains is estimated to be less than 4.7 nm (polar nanodomains). The large dielectric response of the terpolymer comes from the two crystalline phases: the ferroelectric-like crystals and polar nanodomains. The former is responsible for the frequency-independent dielectric maxima while the latter generates the strong frequency dependence in the dielectric spectra, a typical feature of relaxor ferroelectrics, which we suggest to come from the short-range molecular motion in the polar nanodomains.
Three dimensional phase field study on the thickness effect of ferroelectric polymer thin film

tao li,changqing chen,jinxiong zhou

DOI: https://doi.org/10.1063/2.1101108

2011-01-01

Theoretical and Applied Mechanics Letters

Abstract:The electromechanical behavior of poly(vinylidene fluoride-trifluoroethylene) [P(VDF-TrFE)] ferroelectric thin film was investigated using the three dimensional (3D) phase-field method. Various energetic contributions, including elastic, electrostatic, and domain wall energy were taken into account in the variational functional of the phase field model. Evolution of the microscopic domain structures of P (VDF-TrFE) polymer film was simulated. Effects of the in-plane residual stress, the film thickness and externally applied electric bias field on the electromechanical properties of the film were explored. The obtained numerical results showed that the macroscopic responses of the electric hysteresis loops are sensitive to the residual stress and electric bias field. It was also found that thickness has a great effect on the electric hysteresis loops and remanent polarization.
Enhanced Piezoelectric Coefficient of PVDF-TrFE Films via In Situ Polarization

Xiaoran Hu,Mengli You,Na Yi,Xiaokun Zhang,Yong Xiang

DOI: https://doi.org/10.3389/fenrg.2021.621540

IF: 3.4

2021-08-10

Frontiers in Energy Research

Abstract:The d 33 coefficient = 28 pC/N of PVDF-TrFE piezoelectric films was achieved by the in situ polarization. Compared with traditional poling methods, the in situ polarization is performed with low poling voltage and short poling time, and it can ensure the PVDF-TrFE film with enhanced piezoelectric performances and uniform distribution among a large area of 200 mm 2 × 200 mm 2 . The processing influence of drying, annealing, and poling on the crystalline properties and piezoelectric performances were investigated. Besides, the obtained PVDF-TrFE films present a good piezoelectric response to different extents of mechanical stimulations, which have great potential in energy harvesting applications.

energy & fuels
Surface plasmon polariton propagation in nanoscale metal gap waveguides.

B. Wang,Guo Ping Wang

DOI: https://doi.org/10.1364/OL.29.001992

IF: 3.6

2004-09-01

Optics Letters

Abstract:Based on finite-difference time-domain simulation of the propagation characteristics of surface plasmon polaritons (SPPs) in optical circuits made from metal gap waveguides (MGWs) with nanometric gap widths, we theoretically demonstrate that two structures that consist of splitting and recombining MGWs and of coupling MGWs can be used as nanoscale Mach-Zehnder interferometers. MGW arrays show capabilities for array imaging and for controlling the flow of SPPs. Other potential applications of coupling MGWs, as SPP switches, directional couplers, and even as a nanoscale counterpart for observing linear and nonlinear dynamic behavior of electromagnetic fields, are also predicted and discussed. Our results point to an interesting way to manipulate optical signals and provide efficient sensing in nanophotonic architectures.
The tuning of crystallization behavior of ferroelectric poly(vinylidene fluoride‐co‐trifluoroethylene)

Xiao Bai,Haikuo Li,Xiao Chu,Mengling Liu,Huihui Li,Haijun Wang,Xiaoli Sun,Shouke Yan

DOI: https://doi.org/10.1002/pol.20230296

IF: 3.046

2023-12-14

Journal of Polymer Science

Abstract:Poly (vinylidene fluoride‐co‐trifluoroethylene) [P(VDF‐TrFE)] has three crystal forms, including paraelectric α, ferroelectric β, and γ phases. In previous studies, the properties and performances of P(VDF‐TrFE) have been the focus of research. However, the formation mechanism and regulation mode of various crystal forms remain unclear. Therefore, it is an important topic for further research to elucidate, summarize, and prospect the polymorphism of P(VDF‐TrFE) and regulate the crystal forms. This review systematically summarizes the crystalline structure and phase transition between ferroelectric and paraelectric phase of P(VDF‐TrFE) crystals; discusses the influence of annealing, blending and electric field on the crystallinity, selection of polymorphic crystals, and phase transition behavior between them; reviews the effects of annealing, melt‐recrystallization, substrate and nanoconfinement on the crystal orientation. Finally, the effects of the crystal structure of P(VDF‐TrFE) on its properties are briefly summarized.

polymer science
The Evolution of Activation Field with Temperature in Ferroelectric Copolymer of Vinylidene Fluoride and Trifluoroethylene Films

L. Jiang,X. J. Meng,X. L. Zhao,B. B. Tian,B. L. Liu,G. L. Yuan,J. L. Wang,J. L. Sun,Junhao Chu

DOI: https://doi.org/10.4028/www.scientific.net/amr.785-786.761

2013-01-01

Advanced Materials Research

Abstract:Vinylidene fluoride and trifluoroethylene [P(VDF-TrFE)] ferroelectric thin film was spin-coated on Au-coated polyimide substrate and its polarization reversal was investigated by analyzing the evolution of activation field (α) with temperature. Although α is nearly a constant between 300 and 330 K, it increases linearly when temperature rates between 200 and 230 K, and between 230 and 300 K. On the other hand, the intensity of X-ray diffraction for P(VDF-TrFE) films from 200 to 330 K indicates that glass-transition process plays a significant role in both the microstructure and the polarization reversal of P(VDF-TrFE) copolymer.
Ferroelectric and Ferroelastic Domain Related Formation and Influential Mechanisms of Vapor Deposited Piezoelectric Thin Films

Chu Chen,Jian Song,Qi Zhang,Mingyu Gong,Yue Liu,Tongxiang Fan

DOI: https://doi.org/10.3390/coatings11121437

IF: 3.236

2021-11-24

Coatings

Abstract:Compared to the bulk piezoelectric materials counterpart, piezoelectric thin films (PTFs) possess advantages of smaller size, lower power consumption, better sensitivity, and have broad application in advanced micro-electro-mechanical system (MEMS) devices. However, the performance of MEMS transducers and actuators are largely limited by PTFs piezoelectric properties. In this review, we focus on understanding structure-property relationship of vapor deposited PTFs, with emphasis on the effect of strain energy and electrostatic energy in thin films, especially, energy relaxation induced misfit dislocation and ferroelectric (FS) and ferroelastic (FC) domain formation mechanisms. We then discuss the microstructure of these domains and their influential mechanisms on piezoelectric properties, as well as the domain engineering strategies (i.e., internal and external stimuli). This review will motivate further experimental, theoretical, and simulation studies on FS and FC domain engineering in PTFs.

materials science, multidisciplinary,physics, applied, coatings & films

Employing Data Driven Random Membership Subset Algorithm for QoS-Aware Peer-to-Peer Streaming

Solvent Vapor Annealing of Ferroelectric P(VDF-TrFE) Thin Films

Improved Thermal Stability of Ferroelectric Phase in Epitaxially Grown P(VDF-TrFE) Thin Films

Unveiling the piezoelectric nature of polar α-phase P(VDF-TrFE) at quasi-two-dimensional limit

Temperature Control of P(Vdf-Trfe) Copolymer Thin Films

Microstructural influence on thermal stability of ferroelectric properties in P(VDF-TrFE) spin cast thin films

Direct observation of room-temperature out-of-plane ferroelectricity and tunneling electroresistance at the two-dimensional limit

Tuned Dielectric, Pyroelectric and Piezoelectric Properties of Ferroelectric P(Vdf-Trfe) Thin Films by Using Mechanical Loads

Crystallisation behaviours of ferroelectric P(VDF-TrFE) ultrathin films on different substrates

Optimization of electro-strain and ferroelectric properties of P(VDF-TrFE) films under the synergistic effect of PTO nanosheets and in-situ electrostatic field

Giant Electrocaloric Effect in Ferroelectric Ultrathin Films at Room Temperature Mediated by Flexoelectric Effect and Work Function

In Situ Observation of the Nanocrystal Growth and Their Piezoelectric Performance Change in P(Vdf-Trfe) Films by Hot Stage Piezoresponse Force Microscopy

Superior Transverse Piezoelectricity in a Halide Perovskite Molecular Ferroelectric Thin Film

In-situ Electrostatic Field Regulating the Recrystallization Behavior of P(VDF-TrFE) Films with High Β-Phase Content and Enhanced Piezoelectric Properties Towards Flexible Wireless Biosensing Device Applications

Phase Transitions and Ferroelectric Relaxor Behavior in P(VDF−TrFE−CFE) Terpolymers

Three dimensional phase field study on the thickness effect of ferroelectric polymer thin film

Enhanced Piezoelectric Coefficient of PVDF-TrFE Films via In Situ Polarization

Surface plasmon polariton propagation in nanoscale metal gap waveguides.

The tuning of crystallization behavior of ferroelectric poly(vinylidene fluoride‐co‐trifluoroethylene)

The Evolution of Activation Field with Temperature in Ferroelectric Copolymer of Vinylidene Fluoride and Trifluoroethylene Films

Ferroelectric and Ferroelastic Domain Related Formation and Influential Mechanisms of Vapor Deposited Piezoelectric Thin Films