Abstract:New developments in instrumentation for ocean environmental engineering are allowing unprecedented levels of trace contaminant measurement in the deep ocean. With funding from the U.S. National Science Foundation (NSF), our engineering design team constructed a new mass spectrometer-based in situ analysis system for work in the deep ocean environment over prolonged deployment periods. Our design goals were a depth capability of up to 4,000 m water depth (400 bars hydrostatic pressure) and autonomous operation for periods of up to six months to a year, depending upon the type of external battery system used or other deployment circumstances, e.g., availability of a power cable or fuel cell power source. We chose a membrane introduction mass spectrometry (MIMS) sampling approach, which allows for dissolved gases and volatile organics introduction into the mass spectrometer vacuum system. The MIMS approach and the hydrophobic, silicon-coated membrane chosen both draw upon our previous experience with this technology in the deep ocean. The membrane has been tested to 400 bars in a series of long-term hydrostatic pressure tests, which extend the 200-bar working depth rating of this membrane by a factor of 2. Long-term deployment capability of the moderately powered, approximately 100 W system, was accomplished by power management of the embedded computer system and custom electronics with Windows-based and custom software now fully-developed and bench tested. The entire system fits within a 6.5-inch outside diameter pressure housing that is approximately five feet long. It consists of a 1 to 200 amu range quadrupole mass spectrometer equipped with Faraday and electron multiplier detectors, compact turbo-molecular and backing diaphragm vacuum pumps, internal rechargeable batteries, and internal waste vacuum chamber. Sample routing past the MIMS is accomplished by computer-controlled solenoid valves. We designed the pressure housings of both 6AL4V and type 2 titanium alloys that are rated to working depths of >4,000 m and are essentially corrosion proof over long-term deployments. We designed and integrated a fail-safe valving system for both rapid response to high-pressure MIMS failure and a pressure-switch circuit and high-pressure solenoid valve to detect and protect against slow leaks of the MIMS. To route sample waters to the MIMS-based instrument, we also designed and built a rugged plastic plenum that couples to the face of the sampler head, the latter of which consists of the MIMS inlet and a full-ocean rated thermister temperature probe with an operational range from −5 to 50°C. These instrumentation innovations will be described in the paper.

A GPS-enabled seabed sediment sampler: Recovery efficiency and efficacy

Measurement and control system for gas-tight deep-sea water sampler based on LabVIEW

Analysis of Displacement Performance for a Horizontal Flowthrough Sequence Water Sampler

A Pressure-Triggered Isobaric Sequential Liquid Sampling System for Full-Ocean-depth: Design and Field Deployment

Design and Experimental Study of a Novel Full-ocean-depth Pressure-retaining Sediment Sampler

A remotely operated serial sampler for collecting gas-tight fluid samples

A novel submersible-mounted sediment pressure-retaining sampler at full ocean depth

A routine device for high resolution bottom water sampling

Performance of a novel sediment sampler as an add‐on unit for portable free‐fall penetrometers: Combining in situ geotechnical testing with sediment sampling

A Sediment Sample Transfer, Handing, Encapsulation and Analysis Subsystem Device in State of Fidelity

A Deep-Sea Sediment Sampling System: Design, Analysis and Experimental Verification

An instrument system for monitoring and sampling suspended sediment in the benthic boundary layer

Development of an Active, Large Volume, Discrete Seawater Sampler for Autonomous Underwater Vehicles

A Deep-Ocean Mass Spectrometer to Monitor Hydrocarbon Seeps and Pipelines

Review of long seabed samplers and criteria for new sampler design

Design and Experiments of a Portable Seabed Integrated Detection Sonar

Novel gas-tight multi-sampler for discrete deep-sea water

3D Suspended Sediment Concentration Mapping Through GF-1 Satellite Image and Kriging-based Optimal Shipping Path Planning for Acoustic Subsurface Measurements.

Capturing Amphipods in the Mariana Trench with a Novel Pressure Retaining Sampler

In‐situ enrichment of heavy metals from deep‐sea water by an ion‐exchange pump system