The nucleotide sequence of the H-1r gene of Salmonella rubislaw.

L.-N. Wei,T. Joys

DOI: https://doi.org/10.1093/NAR/14.20.8227

IF: 14.9

1986-10-01

Nucleic Acids Research

Abstract:

What problem does this paper attempt to address?

Effectively removing tetracycline from water by nanoarchitectured carbons derived from CO2: Structure and surface chemistry influence

Juan Yang,Xiang Liu,Kexin Song,Xinyue Li,Dihua Wang

DOI: https://doi.org/10.1016/j.envres.2021.110883

IF: 8.3

2021-04-01

Environmental Research

Abstract:Understanding of the correlation between physico-chemical property of adsorbent and the adsorption performance of contaminant is very significant for developing high-efficient materials to remove antibiotic contamination from water. In this work, a novel kind of carbon adsorbent (EC) derived from CO2 and activated ECs with modified structure via a facile chemical method using H2 and KOH were prepared. The synthetic carbon materials (EC, EC-H2, and EC-KOH) were then applied to remove tetracycline (TC). The kinetics of adsorption for these three carbon materials all well fitted the pseudo-second-order kinetic model. The experimental data of adsorption isotherm had good compatibility with Langmuir and Freundlich models (R2 > 0.90), but the Temkin model was the most applicable for all adsorbents (R2 > 0.98). A super-high adsorption capacity of EC-KOH obtained from Langmuir fitting was 933.56 mg g−1, which was much higher than that of EC-H2 (538.91 mg g−1) and EC (423.30 mg g−1), possibly due to its larger specific surface area (SBET), pore volume, and specific surface chemical structure. Moreover, it was found that surface functional groups and large aperture of adsorbents had a positive effect on adsorption rate. More adsorption sites and surface functional groups of adsorbents were beneficial to enhance the adsorption affinity. These results are of great benefit to the directional control of carbon structure to increase the adsorption performance in rate, capacity, and affinity of antibiotics.

environmental sciences,public, environmental & occupational health
Utilizing a novel green ternary polymeric nanocomposite material to remove tetracycline antibiotic effectively from aqueous solutions

Nazir Mustapha,Marwa H. Gouda,M. Abdel Rafea,M. Salerno,Ashour M. Ahmed,Noha A. Elessawy

DOI: https://doi.org/10.1007/s10450-024-00514-2

2024-07-18

Adsorption

Abstract:Highly efficient removal of tetracycline antibiotic residue from aqueous solution was demonstrated by a novel, cost effective and environmentally friendly adsorbent consisting in composite polymeric beads of sodium alginate, chitosan and polyvinyl pyrrolidone, doped with equal ratio of sulfonated graphene oxide and sulfonated titania, fabricated via simple blending method using calcium chloride as a crosslinker. The adsorption parameters of beads amount, initial tetracycline concentration, adsorption time and solution pH were investigated. Furthermore, adsorption time, beads amount, and the initial tetracycline concentration were optimized using the response surface methodology model. Pseudo-second-order kinetic equation was fitted to the adsorption process' kinetics. It was discovered that the electrostatic attraction and hydrogen bonding, which primarily contribute to the noticeably enhanced adsorption ability, are the essential factors driving the adsorption mechanism. The maximum antibiotic adsorption capacity of the nanocomposite beads reached 357 mg/g.

chemistry, physical,engineering, chemical
Effective removal of tetracycline antibiotics from wastewater using practically applicable iron(III)-loaded cellulose nanofibres

Lanxin Lu,Min Liu,Ying Chen,Ying Luo

DOI: https://doi.org/10.1098/rsos.210336

IF: 3.5

2021-08-01

Royal Society Open Science

Abstract:The non-toxic and completely biodegradable cellulose within bamboo is one of the most abundant agricultural polysaccharide wastes worldwide, and can be processed into cellulose nanofibres (CNFs). Iron(III)-loaded CNFs (Fe(III)@CNFs) derived from bamboo were prepared to improve the adsorption of tetracycline (TC), chlortetracycline (CTC) and oxytetracycline (OTC) from an aqueous solution. The preparation conditions of Fe(III)@CNFs suitable for the simultaneous adsorption of three tetracycline antibiotics (TCs) were investigated. Various analyses proved the abundance of oxygen-containing functional groups and the existence of Fe(III) active metal sites in Fe(III)@CNFs. In batch experiments, Fe(III)@CNFs were applied under a wide pH range and the maximum adsorption capacities were 294.12, 232.56 and 500.00 mg g −1 (for TC, CTC and OTC, respectively). In addition, different concentrations and types of coexisting anions have a weak effect on TCs adsorption. The original TCs adsorption capacities of Fe(III)@CNFs remained stable (greater than 92%) after five cycles when UV + H 2 O 2 was used as the regeneration method. Four adsorption mechanisms (surface complexation, hydrogen bonding, electrostatic interaction and van der Waals force) were obtained for the endothermic adsorption of TCs, among which surface complexation between Fe(III) and TCs always dominates. The practically applicable Fe(III)@CNFs adsorbents are promising for TCs enrichment and remediation in engineering applications.

multidisciplinary sciences
Efficient Adsorbent Derived from Phytolith-Rich Ore for Removal of Tetracycline in Wastewater

Xi Liu,Yili Tang,Xianguang Wang,Muhammad Tariq Sarwar,Xiaoguang Zhao,Juan Liao,Jun Zhang,Huaming Yang

DOI: https://doi.org/10.1021/acsomega.3c09049

IF: 4.1

2024-02-07

ACS Omega

Abstract:In recent decades, the tetracycline (TC) concentration in aquatic ecosystems has gradually increased, leading to water pollution problems. Various mineral adsorbents for the removal of tetracyclines have garnered considerable attention. However, efficient adsorbents suitable for use in a wide pH range environment have rarely been reported. Herein, a phytolith-rich adsorbent (PRADS) was prepared by a simple one-step alkali-activated pyrolysis treatment using phytolith as a raw material for effectively removing TC. PRADS, benefiting from its porous structure, which consists of acid- and alkali-resistant, fast-adsorbing macroporous silica and mesoporous carbon, is highly desirable for efficient TC removal from wastewater. The results indicate that PRADS exhibited excellent adsorption performance and stability for TC over a wide pH range of 2.0-12.0 under the coexistence of competing ions, which could be attributed to the fact that PRADS has a porous structure and contains abundant oxygen-containing functional groups and a large number of bonding sites. The adsorption mechanisms of PRADS for TC were mainly attributed to pore filling, hydrogen bonding, π-π electron-donor-acceptor, and electrostatic interactions. This work could offer a novel preparation strategy for the effective adsorption of pollutants by new functionalized phytolith adsorbents.
Adsorption and Removal of Antibiotic Pollutants using CuO-Co3O4 Co-modified Porous Boron Nitride Fibers in Aqueous Solution

Wenjuan Bai,Bozheng Wang,Shaobo Yang,Song Yan,Chaochao Cao,Zheng Zhou,Jiawei Ji,Kai Guo,Chengchun Tang

DOI: https://doi.org/10.1002/cplu.202200290

2022-01-01

ChemPlusChem

Abstract:The presence of antibiotic contaminants in aqueous environment already poses significant risks to ecological sustainability, biodiversity and human public health and safety. Therefore, it is urgent to develop practical water pollution control technologies and new materials. Here, we prepared CuO-Co3O4 co-modified porous boron nitride fibers (P-BNFs) for the adsorption and removal of tetracycline antibiotics (TCs) in aqueous environment. The prepared adsorbents were characterized by XRD, FTIR, XPS, SEM, TEM and BET, and the adsorption behavior was explored by batch experiments. The results show that the removal percentage for doxycycline (DC) reaches 98.68 %, which was much higher than that of P-BNFs, and the modification results of P-BNFs with CuO or Co3O4 alone. After five regeneration cycles, the removal rate of DC by CuO-Co3O4/P-BNFs was still as high as 89.33 %. This is promising and indicates that the prepared CuO-Co3O4/P-BNFs adsorbent has good renewable recycling performance and practical application prospects.
Batch Experimental Studies and Statistical Modeling for the Effective Removal of Tetracycline from Wastewater Using Bimetallic Zn-Cu-Metal-Organic Framework@Hydrogel Composite Beads

Harshita Laddha,Priya Sharma,Neha Balaji Jadhav,Md Zainul Abedeen,Ragini Gupta

DOI: https://doi.org/10.1021/acs.langmuir.3c02385

IF: 3.9

2023-12-12

Langmuir

Abstract:Antimicrobial resistance (AMR) is on an upsurge as more and more broad-spectrum antibiotics are being used haphazardly, resulting in imbalances in the ecosystem and disrupting common/systematic clinical protocols. To combat this issue, metal-organic framework embedded zinc-copper-benzenedicarboxylate@calcium alginate composite beads (Zn-Cu-BDC@CA CBs) were synthesized and utilized for the adsorption of tetracycline (TC) from water. The surface morphology, presence of functional groups, surface area, and thermal stability of Zn-Cu-BDC@CA CBs were evaluated by field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET), and thermal gravimetric analysis (TGA), respectively. Batch adsorption experiments were also carried out to optimize the adsorption performance of Zn-Cu-BDC@CA CBs for TC by adjusting the key parameters, including pH of the solution, contact time, adsorbent dosage, temperature, and initial concentration of TC. From the RSM model, 96.8% removal of TC takes place under the optimum conditions (pH = 7.3, mass = 17.2 mg, concentration = 21.3 ppm, time = 3.4 h, and temperature = 31.8 °C), which aligns closely with the experimental batch study, where the addition of 20 mg of adsorbent to a 20 mL TC solution (20 mg/L) at a pH of 7 and a temperature of 27 °C yielded an impressive TC removal efficiency of 96.55% within 180 min. Zn-Cu-BDC@CA CBs possess homogeneous adsorption surfaces, and TC is adsorbed via monolayer chemisorption, according to the results derived from the Langmuir isotherm model and pseudo-second-order kinetic model. The thermodynamic analysis indicated that the adsorption process is both endothermic and spontaneous. In their entirety, the synthesized Zn-Cu-BDC@CA CBs exhibit certain operational advantages, such as simple separation, satisfactory adsorption performance, and decent recyclability, indicating their viability for industrial application of elimination of TC residues from aquatic environments.
Preparation of TiO2/cellulose nanocomposites as antibacterial bio-adsorbents for effective phosphate removal from aqueous medium

Enmin Zong,Chen Wang,Jiayao Yang,Hangxuan Zhu,Shengtao Jiang,Xiaohuan Liu,Pingan Song

DOI: https://doi.org/10.1016/j.ijbiomac.2021.04.007

IF: 8.2

2021-07-01

International Journal of Biological Macromolecules

Abstract:The design of environmentally benign bio-adsorbents for the removal of phosphate from aqueous medium was an economic and effective way for controlling eutrophication. Herein, we prepared three kinds of TiO2/cellulose (CE-Ti) nanocomposites by in situ precipitation method, and used them as antibacterial bio-adsorbents for the removal of phosphate from aqueous medium. Multiple techniques including Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) and thermogravimetric analysis (TGA) were employed to characterize the nanostructure and characteristics of the prepared CE-Ti nanocomposite. The adsorption capacity of the CE-Ti was 19.57 mg P g−1 according to the Langmuir model, which was 6 times higher than that of CE. Importantly, the bacterial inhibition zone of the CE-Ti was 2.88 mm (that of CE was 0 mm), indicating that CE-Ti had good antibacterial activity that could reduce the attachment of the microorganism to the surface of CE-Ti, which was suitable for long-term phosphate removal. Moreover, the CE-Ti had good adsorption selectivity and anti-interference capability, according to interfering ions and ion strength experiments. Furthermore, Ti4+ leakage tests suggested that CE-Ti was highly stable under acidic, neutral and alkali conditions. These results indicated that the CE-Ti nanocomposite could be utilized as a promising antibacterial bio-adsorbent for effective phosphate removal from aqueous medium.

polymer science,biochemistry & molecular biology,chemistry, applied
Adsorptive removal of oxytetracycline using MnO2-engineered pine-cone biochar: thermodynamic and kinetic investigation and process optimization

Prakash Bobde,Amit Kumar Sharma,Ranjit Kumar,Sukdeb Pal,Jitendra Kumar Pandey,Shikha Wadhwa

DOI: https://doi.org/10.1007/s10661-023-11932-0

IF: 3.307

2023-10-13

Environmental Monitoring and Assessment

Abstract:Indiscriminate use of oxytetracycline is linked to the development of antibiotic-resistant genes, posing a serious threat to human health and ecosystem balance. This article reports the adsorptive elimination of oxytetracycline (OTC) from aqueous solution using a newly developed MnO 2 -modified pine-cone biochar (MnO 2 /PCBC). The MnO 2 /PCBC was characterized using X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, CHNS analyzer, inductively coupled plasma–optical emission spectroscopy, and Brunauer-Emmett-Teller N 2 adsorption analyzer. Batch adsorption experiments, designed using the central composite design framework of response surface methodology, were conducted to investigate the influence of process variables on the adsorption of OTC onto MnO 2 /PCBC. The optimized conditions for achieving maximum removal (88.1%) were found to be at pH 8, MnO 2 /PCBC dose 0.44 g/L, initial OTC concentration 200 mg/L, and temperature 303 K. The adsorption process follows Langmuir ( R 2 =0.95) and Freundlich ( R 2 =0.95) isotherms and pseudo-second-order ( R 2 =0.99) adsorption kinetics. The adsorption process was found to be endothermic (Δ H 0 = 33.04 kJ/mol) and spontaneous in nature (Δ G 0 from −1.33 kJ/mol at 283 K to −5.65 kJ/mol at 313 K). The synthesized MnO 2 /PCBC could be recycled and reused for OTC removal with a percentage removal of around 80% after fifth cycle. The results indicate an effective removal of oxytetracycline with only 0.44 g/L MnO 2 /PCBC with maximum adsorption capacity of 357.14 mg/g which demonstrates improved performance in comparison to many adsorbents reported in literature. This implies that MnO 2 /PCBC offers potential to be developed into a cost-effective technique for antibiotic removal from water.

environmental sciences
Adsorption of ciprofloxacin from aqueous solution using surface improved tamarind shell as an economical and effective adsorbent

Magesh N,Annam Renita A,Senthil Kumar P,Stanley Abraham L,Magesh N.,Annam Renita A.,Senthil Kumar P.,Stanley Abraham L.

DOI: https://doi.org/10.1080/15226514.2021.1932730

2021-06-14

International Journal of Phytoremediation

Abstract:Antibiotics in water bodies are emerging as an alarming new pollutant because of its persistent and recombinant nature. In recent period of human lifestyle, pharmaceutical products play a vital role in many perspectives. Due to this unpredictable usage of products, the unreacted components release into waterbodies in trace quantities. Eventhough these trace quantities initiate a crisis of developing resistant antibacterial strains which pose health risks to humans and animals. This work reports the batch adsorption of a fluoroquinolone, a fourth-generation antibiotic compound by a biosorbent made by acid-treated tamarind shells. The shells were treated with zinc chloride and hydrochloric acid. The characterization of biosorbent was performed by Fourier transform infrared spectroscopy and field emission scanning electron microscopy. The optimized adsorption parameters of time, pH and temperature were 30 minutes, 6 and 60 °C. The adsorbent can be reused up to seven times with negligible loss in its adsorption capacity. Adsorption followed by Langmuir, Freundlich and Tempkin model where used to determine the correlation coefficient. Pseudo first-order, second-order and intra-particle kinetic model were used to fit the experimental data. The results are best described by pseudo second-order denoting chemisorption and Freundlich isotherm model describing multilayer adsorption.The proposed work is to investigate about improved tamarind shell as biomass used in the removal unreacted PPCP components that have been released into aquatic environment.The novelty of this paper lies in that it puts forward a better resource utilization method for treating PPCP component wastewater, and studies the method theoretically from the perspective of mechanism and proves its feasibility.Identifying the maximum adsorption of antibiotic component from wastewater under different conditions and finding the optimum range.In addition to the existing literatures, this study has compared the adsorption efficiency of raw and treated adsorbent material prepared using Tamarind shell.
Activating peroxymonosulfate with Fe-doped biochar for efficient removal of tetracycline: Dual action of reactive oxygen species and electron transfer

Wei Zuo,Yuqing Mao,Wei Zhan,Lipin Li,Yu Tian,Jun Zhang,Wanli Ma,Chuandong Wu,Li Zhao

DOI: https://doi.org/10.1016/j.jenvman.2024.120979

IF: 8.7

2024-05-01

Journal of Environmental Management

Abstract:If pharmaceutical wastewater is not managed effectively, the presence of residual antibiotics will result in significant environmental contamination. In addition, inadequate utilization of agricultural waste represents a squandering of resources. The objective of this research was to assess the efficacy of iron-doped biochar (Fe-BC) derived from peanut shells in degrading high concentrations of Tetracycline (TC) wastewater through activated peroxymonosulfate. Fe-BC demonstrated significant efficacy, achieving a removal efficiency of 87.5% for TC within 60 min without the need to adjust the initial pH (20 mg/L TC, 2 mM PMS, 0.5 g/L catalyst). The degradation mechanism of TC in this system involved a dual action, namely Reactive Oxygen Species (ROS) and electron transfer. The primary active sites were the Fe species, which facilitated the generation of SO 4 •- , •OH, O 2 •- , and 1 O 2 . The presence of Fe species and the C=C structure in the Fe-BC catalyst support the electron transfer. Degradation pathways were elucidated through the identification of intermediate products and calculation of the Fukui index. The Toxicity Estimator Software Tool (T.E.S.T.) suggested that the intermediates exhibited lower levels of toxicity. Furthermore, the system exhibited exceptional capabilities in real water and circulation experiments, offering significant economic advantages. This investigation provides an efficient strategy for resource recycling and the treatment of high-concentration antibiotic wastewater.

environmental sciences
Efficient removal of tetracycline in water by a Fe 3 O 4 -mediated persulfate activation and biodegradation coupled system: Performance, validation, and mechanism

Li Wang,Yuxuan Ye,Zhikang Zeng,Yangxin Wang,Mengyao Han,Xuanyuan Pei,Dandan Wang,Fei Pan

DOI: https://doi.org/10.1016/j.jwpe.2023.103718

IF: 7

2023-04-19

Journal of Water Process Engineering

Abstract:The cost-effective removal of antibiotic contaminants from the aqueous environment has become a hot research topic now. In this study, we proposed a novel coupled system, i.e., nano-Fe 3 O 4 (nFe 3 O 4 ) mediated persulfate (PDS) activation and biodegradation process, for efficient removal of tetracycline (TCH). The feasibility of the coupled system (nFe 3 O 4 + PDS + microbe) was proved by comparing it with a single AOP (nFe 3 O 4 + PDS) in batch and column experiments. The highest removal efficiencies of TCH (20 mg/L) and TOC reached 99.5 % and 43.2 % by the coupled system within 60 days. SEM spectra exhibited that nFe 3 O 4 and microorganisms were well loaded on the non-woven fabric. Meanwhile, XPS results proved that more Fe(II) was on the surface of nFe 3 O 4 in the coupled system than that in the single AOP. The presence of abundant Fe(II) in the coupled system suggested the potential electron transfer from Fe(III) with the assistance of microbes. High-throughput sequencing results indicated Proteobacteria played an important role in the coupled system. The degradation intermediates of TCH were analyzed by ultraperformance liquid chromatography-mass spectrometer (UPLC-MS), and reasonable degradation pathways were proposed. The coupling of nFe 3 O 4 + PDS and biological treatment improved the TCH removal efficiency and reduced the burden of subsequent water treatment, which provided a feasible idea for the treatment of antibiotic-containing wastewater.

engineering, chemical, environmental,water resources
Working with the World Health Organization.

D. O'mullane

2002-06-01

Community dental health

Abstract:
Efficient Removal of Tetracycline from Wastewater Via KHCO3-activated Biochar: Characterization, Performance, and Mechanism

Yuzheng Zou,Wentao Yang,Yonglin Chen,Jian Zhang,Bing Wang,Nabeel Khan Niazi,Liyu Yang,Shengsen Wang,Hang Zhou,Pan Wu

DOI: https://doi.org/10.1016/j.jwpe.2024.106450

IF: 7

2024-01-01

Journal of Water Process Engineering

Abstract:Tetracycline (TC) is widely used in the aquaculture and healthcare industries. However, massive TC is discharged into the surrounding aquatic environment through prodrugs or parent compounds, as neither humans nor animals can metabolize it directly. TC contamination of water has become a significant worldwide environmental challenge. In this study, a novel biochar RK1.2BC was generated by rapeseed residue co-pyrolyzed with KHCO3. Adsorption experiments and characterization techniques were performed to examine the performance and mechanisms of RK1.2BC in removing TC from wastewater. These findings demonstrated that RK1.2BC is an effective material for TC removal. At 298.15 K and pH 6.0, the maximal capacity of RK1.2BC for TC adsorption in theory was 783.82 mg·g−1, approximately 12.37-fold greater than nonactivated biochar. The specific surface area (1570.28 m2·g−1) and the total volume of pores (0.94 m3·g−1) of RK1.2BC increased 360-fold and 94-fold, respectively. RK1.2BC maintained high adsorption capacity across a broad range of water pH (2.0–11.0). The RK1.2BC is highly resistant to ionic interference, TC adsorption capacity was >450.96 mg·g−1 at 100 mg·L−1 of anions (SO42−, NO3−, PO43−, HCO3−, CO32−), cations (Na+, Ca2+, K+, Mg2+, Cd2+), and natural organic matter (Humic Acid and Citric Acid). RK1.2BC demonstrated excellent TC adsorption in natural water (>402.38 mg·g−1) and retained a strong ability to adsorb (>243.08 mg·g−1) following five rounds of desorption-regeneration. Furthermore, TC adsorption process was governed primarily by homogeneous monolayer chemisorption, the adsorption mechanism involves π-π EDA interactions, hydrophobic interactions, electrostatic interactions, hydrogen bonding, and pore filling.
Removal of four antibiotics from the aqueous phase using Polyethylene adsorbent: Mechanistic understanding and reusability potential

Rabeea Zafar,Rehan Zafar Paracha,Abdulwahed Fahad Alrefaei,Mohammed Fahad Albeshr,Muhammad Yousuf Jat Baloch,Jean Kallerhoff,Muhammad Arshad

DOI: https://doi.org/10.1016/j.eti.2024.103831

IF: 7.758

2024-09-20

Environmental Technology & Innovation

Abstract:The release of pollutants of emerging concerns like antibiotics in the environment is posing serious threats to ecosystems. The aim of this study was to remove four antibiotics from the aqueous phase using polymer-based adsorbent in its raw form for antibiotic removal coupled with a mechanistic understanding of the process. Polyethylene, post-cleaning, served as an adsorbent, characterized for surface area, pore size, and structure. Two-week batch experiments at 25°C and pH 7 were conducted at a laboratory scale. Polyethylene demonstrated over 90% removal efficiencies for all the selected antibiotics. Data fitting into various models revealed Langmuir isotherm and Elovich kinetic model governed the adsorption. Antibiotics, excluding ciprofloxacin, followed second-order kinetics; ciprofloxacin was governed by pseudo-first-order kinetics. Pseudo-second-order kinetics had R 2 values of 0.9855, 0.9746, and 0.9997 for ofloxacin, sulfamethoxazole, and oxytetracycline, respectively. Elovich had R 2 values over 0.90 for all the antibiotics, with the order of values as oxytetracycline>ofloxacin>sulfamethoxazole> ciprofloxacin. Langmuir Isotherm indicated the R 2 value of 0.9777, 0.9902, 0.9551, and 0.9959 for ofloxacin, ciprofloxacin, sulfamethoxazole, and oxytetracycline, respectively. Regeneration results exhibited that all antibiotics had greater than 80% removal efficiencies in the first two cycles while the regeneration capacity of ciprofloxacin and sulfamethoxazole reduced to 75% and 50%, respectively at the fourth cycle. The effective removal of antibiotics indicates its usefulness and potential for widespread application compared to the costly and chemical-intensive adsorbents. These findings highlight the potential of selected adsorbents for real-time applications as the lab-scale studies mimicked the real environment by using a mixture of antibiotics.

environmental sciences,engineering, environmental,biotechnology & applied microbiology
Tetracycline removal via adsorption and metal-free catalysis with 3D macroscopic N-doped porous carbon nanosheets: Non-radical mechanism and degradation pathway

Yaqian Shen,Ke Zhu,Dongdong He,Jin Huang,Hongmei He,Lele Lei,Wenjin Chen

DOI: https://doi.org/10.1016/j.jes.2021.04.014

IF: 6.9

2022-01-01

Journal of Environmental Sciences

Abstract:Recently, metal-based carbon materials have been verified to be an effective persulfate activator, but secondary pollution caused by metal leaching is inevitable. Hence, a green metal-free 3D macroscopic N-doped porous carbon nanosheets (NPCN) was synthesized successfully. The obtained NPCN showed high adsorption capacity of tetracycline (TC) and excellent persulfate (PS) activation ability, especially when calcined at 700 °C (NPCN-700). The maximum adsorption capacity of NPCN-700 was 121.51 mg/g by H-bonds interactions. Moreover, the adsorption process followed pseudo-second-order kinetics model and Langmuir adsorption isotherm. The large specific surface area (365.27 mg/g) and hierarchical porous structure of NPCN-700 reduced the mass transfer resistance and increased the adsorption capacity. About 96.39% of TC was removed after adding PS. The effective adsorption of the catalyst greatly shortened the time for the target organic molecules to migrate to the catalyst. Moreover, the NPCN-700 demonstrated high reusability with the TC removal rate of 80.23% after 4 cycles. Quenching experiment and electron paramagnetic resonance (EPR) test confirmed the non-radical mechanism dominated by 1O2. More importantly, the C = O groups, defects and Graphitic N acted as active sites to generate 1O2. Correspondingly, electrochemical measurement revealed the direct electron transfer pathway of TC degradation. Finally, multiple degradation intermediates were recognized by the LC-MS measurement and three possible degradation pathways were proposed. Overall, the prepared NPCN had excellent application prospects for removal of antibiotics due to its remarkable adsorption and catalytic degradation capabilities.

environmental sciences
Synergic removal of tetracycline using hydrophilic three-dimensional nitrogen-doped porous carbon embedded with copper oxide nanoparticles by coupling adsorption and photocatalytic oxidation processes

Yiping Su,Shun Li,Guimin Jiang,Zuquan Zheng,Chao Wang,Shiyin Zhao,Daling Cui,Yong Liu,Boping Zhang,Zuotai Zhang

DOI: https://doi.org/10.1016/j.jcis.2020.07.071

IF: 9.9

2021-01-01

Journal of Colloid and Interface Science

Abstract:Adsorption and photocatalytic oxidation are promising technologies for eliminating antibiotics (e.g. tetracycline) in aquatic environments. However, traditional powdery nanomaterials are limited by drawbacks of difficult separation and lack of synergistic function, which do not conform to the practical demand. Herein, we developed a simple one-step gelation-pyrolysis route to fabricate hydrophilic three-dimensional (3D) porous photocatalytic adsorbent, in which CuO nanoparticles are uniformly and firmly embedded in nitrogen-doped (N-doped) porous carbon frameworks. The obtained N-doped carbon/CuO bulky composites exhibited excellent ability to adsorb tetracycline hydrochloride (TC), which was subsequently photo-oxidized under visible light. Their hydrophilic nature favors the adsorption processes toward TC, with a maximum adsorption capacity reaching 25.03 mg∙g−1. In addition, >94.4% of TC molecules could be photo-degraded in 4 h with good cycling efficiency after three consecutive tests. Finally, a reaction scheme for removal process of TC was proposed. The obtained 3D porous N-doped carbon/CuO nanocomposites show great promise for efficient removal of antibiotics in aqueous solution by synergistically utilizing adsorption and photocatalytic oxidation processes.

chemistry, physical
An effective strategy for removing tetracycline from water: Enhanced adsorption reliability and capacity by tyrosine modified layered hydroxides

Caifeng Xia,Xiangming Li,Yuan Xie,Fanping Kong,Menglan Zhao,Yu Wang,Yang Wang,Qian Zhang,Zilin Meng

DOI: https://doi.org/10.1016/j.jece.2022.109172

IF: 7.7

2022-12-23

Journal of Environmental Chemical Engineering

Abstract:The discharge of tetracycline (TCs) antibiotics into the natural environment poses a serious threat to human beings. In the removal of antibiotics by adsorption method, both increase of adsorption capacity and enhancement of adsorption reliability should be considered. In this study, tyrosine intercalated layered double hydroxide () was prepared by a one-step method and characterized by XRD, FT-IR, and SEM. Adsorption kinetics and isotherms studies revealed that compared with LDHs, the adsorption of TC by was a multi-layer adsorption process, with more adsorption sites and larger adsorption capacity. Thermodynamic experiments showed that increasing temperature was beneficial to TC adsorption, indicating adsorption was an endothermic process. In the results of the molecular dynamics study, TC molecules entered the interlayer of LDHs by hydrophobic interaction, and possessed strong interactions with Tyr molecules by electron donor and acceptor, hydrogen bonding, and electrostatic interaction. The antibacterial experiments showed that the inhibition zone of was smaller than that of LDHs, indicating that with the presence of Tyr, TC molecules were adsorbed reliably. pH, coexisting ions, and recycle experiments proved that had reliable adsorption for TC and stability in complex environments. Overall, material was expected to be an adsorbent with good adsorption efficiency and reliable adsorption performance for the treatment of TC from the environment.

engineering, chemical, environmental
Efficient Removal of Antibiotics From Water via a Novel Magnetic Hypercrosslinked Polymer

Yin Liu,Shanhu Chen,Liang Shen,Qiuyu Zhang

DOI: https://doi.org/10.1002/aoc.7895

IF: 3.9

2024-11-27

Applied Organometallic Chemistry

Abstract:The prepared magnetic hypercrosslinked polymers with high surface areas and excellent magnetic properties are potential candidates for adsorption of antibiotics. The removal of antibiotic residues from environmental media is a significant challenge in the field of chemistry. In this work, we presented a simple and efficient method for eliminating tetracycline hydrochloride (TC) and chloramphenicol (CAP) from water. Initially, 1,4‐dichlorobenzene and ferrocene were employed as starting materials for the synthesis of hypercrosslinked polymers (HFDs) via Friedel–Crafts alkylation facilitated by a cross‐linking agent. Subsequent to this, an efficient magnetic adsorbent material (MHFD) was developed by the in situ oxidation of the iron source incorporated within the polymer matrix of HFDs. The resulting MHFDs demonstrated an impressive maximum Brunauer–Emmett–Teller (BET)–specific surface area of 1190 m2/g and exhibited a peak saturation magnetization of 11.8 emu/g. This work investigated the effects of four factors on the adsorption performance of MHFD‐10, including contact time, solution pH, dosage of MHFD‐10, and initial antibiotic concentration. The results revealed a remarkable conformity of the adsorption kinetics with the pseudo‐second‐order model and the adsorption isotherms with the Langmuir model. Thermodynamic analysis revealed that the adsorption process is spontaneous and exothermic. Specifically, at a temperature of 20°C, MHFD‐10 achieved maximum adsorption capacities of 193.95 mg/g for CAP and 268.60 mg/g for TC. Furthermore, these materials exhibited exceptional reusability, maintaining high adsorption capacities even after undergoing five consecutive reuse cycles.

chemistry, inorganic & nuclear, applied
Simple Urea Immersion Enhanced Removal Of Tetracycline From Water By Polystyrene Microspheres

Junjun Ma,Bing Li,Lincheng Zhou,Yin Zhu,Ji Li,Yong Qiu

DOI: https://doi.org/10.3390/ijerph15071524

IF: 4.614

2018-01-01

International Journal of Environmental Research and Public Health

Abstract:Antibiotics pose potential ecological risks in the water environment, necessitating their effective removal by reliable technologies. Adsorption is a conventional process to remove such chemicals from water without byproducts. However, finding cheap adsorbents with satisfactory performance is still a challenge. In this study, polystyrene microspheres (PSM) were enhanced to adsorb tetracycline by surface modification. Simple urea immersion was used to prepare urea-immersed PSM (UPSM), of which surface groups were characterized by instruments to confirm the effect of immersion. Tetracycline hydrochloride (TC) and doxycycline (DC) were used as typical adsorbates. The adsorptive isotherms were interpreted by Langmuir, Freundlich, and Tempkin models. After urea immersion, the maximum adsorption capacity of UPSM at 293 K and pH 6.8 increased about 30% and 60%, achieving 460 mg/g for TC and 430 mg/g for DC. The kinetic data were fitted by first-order and second-order kinetics and Weber Morris models. The first-order rate constant for TC adsorption on UPSM was 0.41 /h, and for DC was 0.33 /h. The cyclic urea immersion enabled multilayer adsorption, which increased the adsorption capacities of TC on UPSM by two to three times. The adsorption mechanism was possibly determined by the molecular interaction including pi-pi forces, cation-pi bonding, and hydrogen bonding. The simple surface modification was helpful in enhancing the removal of antibiotics from wastewater with similar structures.
Magnetic Porous Material Derived from Ni-MOF for the Removal of Tetracycline from Aqueous Solution

Yuhui Xue,Jingjing Wang,Meng Wang,Jiang Li,Kefu Wang,Afaq Hassan,Changyan Guo,Jide Wang

DOI: https://doi.org/10.1021/acsanm.4c00278

IF: 6.14

2024-03-20

ACS Applied Nano Materials

Abstract:The efficient removal of antibiotic residues from aqueous solution is very important for water security. Studies have found that adsorption is widely used for the removal of antibiotics due to its cost-effectiveness, low energy consumption, simplicity of operation, and environmental friendliness. In this study, a novel magnetic porous carbon adsorbent (Ni-MPC-400) with a high adsorption capacity and saturation magnetization was synthesized via direct carbonization of Ni-MOF at 400 °C pyrolysis temperature and used to efficiently remove tetracycline from an aqueous solution. Adsorption experiments showed that Ni-MPC-400 exhibited excellent tetracycline adsorption capacity (441.51 mg·g–1) from the aqueous solution. Possible adsorption mechanisms were proposed through characterization and analysis. The adsorption mechanisms mainly involved π–π interactions, hydrogen bonding, metal–organic complexation, and pore filling effects. In addition, Ni-MPC-400 showed rapid and sufficient adsorption at a low concentration of tetracycline (5 mg·L–1) and good adsorption performance over a wide pH range. In addition, the material has been tested to have good immunity to interference and regenerative capacity, demonstrating a potential application in the removal of tetracycline contaminants from aqueous solutions.

materials science, multidisciplinary,nanoscience & nanotechnology

The nucleotide sequence of the H-1r gene of Salmonella rubislaw.

Effectively removing tetracycline from water by nanoarchitectured carbons derived from CO2: Structure and surface chemistry influence

Utilizing a novel green ternary polymeric nanocomposite material to remove tetracycline antibiotic effectively from aqueous solutions

Effective removal of tetracycline antibiotics from wastewater using practically applicable iron(III)-loaded cellulose nanofibres

Efficient Adsorbent Derived from Phytolith-Rich Ore for Removal of Tetracycline in Wastewater

Adsorption and Removal of Antibiotic Pollutants using CuO-Co<sub>3</sub>O<sub>4</sub> Co-modified Porous Boron Nitride Fibers in Aqueous Solution

Batch Experimental Studies and Statistical Modeling for the Effective Removal of Tetracycline from Wastewater Using Bimetallic Zn-Cu-Metal-Organic Framework@Hydrogel Composite Beads

Preparation of TiO2/cellulose nanocomposites as antibacterial bio-adsorbents for effective phosphate removal from aqueous medium

Adsorptive removal of oxytetracycline using MnO2-engineered pine-cone biochar: thermodynamic and kinetic investigation and process optimization

Adsorption of ciprofloxacin from aqueous solution using surface improved tamarind shell as an economical and effective adsorbent

Activating peroxymonosulfate with Fe-doped biochar for efficient removal of tetracycline: Dual action of reactive oxygen species and electron transfer

Efficient removal of tetracycline in water by a Fe 3 O 4 -mediated persulfate activation and biodegradation coupled system: Performance, validation, and mechanism

Working with the World Health Organization.

Efficient Removal of Tetracycline from Wastewater Via KHCO3-activated Biochar: Characterization, Performance, and Mechanism

Removal of four antibiotics from the aqueous phase using Polyethylene adsorbent: Mechanistic understanding and reusability potential

Tetracycline removal via adsorption and metal-free catalysis with 3D macroscopic N-doped porous carbon nanosheets: Non-radical mechanism and degradation pathway

Synergic removal of tetracycline using hydrophilic three-dimensional nitrogen-doped porous carbon embedded with copper oxide nanoparticles by coupling adsorption and photocatalytic oxidation processes

An effective strategy for removing tetracycline from water: Enhanced adsorption reliability and capacity by tyrosine modified layered hydroxides

Efficient Removal of Antibiotics From Water via a Novel Magnetic Hypercrosslinked Polymer

Simple Urea Immersion Enhanced Removal Of Tetracycline From Water By Polystyrene Microspheres

Magnetic Porous Material Derived from Ni-MOF for the Removal of Tetracycline from Aqueous Solution