ANNOUNCEMENT: 2001 Best Paper Award Committee

I. Sloan,A. Werschulz

DOI: https://doi.org/10.1006/jcom.2001.0605

IF: 1.333

2001-09-01

Journal of Complexity

Abstract:

What problem does this paper attempt to address?

Polyelectrolyte membranes prepared by dynamic self-assembly of poly (4-styrenesulfonic acid-co-maleic acid) sodium salt (PSSMA) for nanofiltration (I)

Hui-Yu Deng,You-Yi Xu,Bao-Ku Zhu,Xiu-Zhen Wei,Fu Liu,Zhen-Yu Cui

DOI: https://doi.org/10.1016/j.memsci.2008.06.028

IF: 9.5

2008-01-01

Journal of Membrane Science

Abstract:In recent years, the layer-by-layer (LBL) self-assembly of polyelectrolyte has attracted much attention for the preparation of nanofiltration (NF) membranes. However, most researchers focused on the homopolymers, few studied on the copolymers for the preparation of NF membranes. In the present work, a series of nanofiltration membranes were prepared by dynamic self-assembly of a copolymer polyelectrolyte containing both weakly and strongly ionized groups, poly (4-styrenesulfonic acid-co-maleic acid) sodium salt (PSSMA), with poly (allylamine hydrochloride) (PAH) and poly (styrenesulfonic acid sodium salt) (PSS) on the modified polyacrylonitrile (PAN) ultra-filtration membranes. The effects of substrate, deposition pH, SS/MA ratio in PSSMA, concentration of the PSSMA and bilayer number on the properties of the NF membranes were investigated. The results indicated that the performances of the NF membranes prepared by dynamic self-assembly process were superior to those prepared by the static self-assembly process. The membranes terminated with PSSMA were negatively charged. Due to the changes of charge density and conformation of PSSMA in different pH conditions, the [PAH/PSS]1PAH/PSSMA membrane prepared at pH 2.5 showed higher Na2SO4 rejection and larger flux than those of the membrane prepared at pH 5.7. The NF membrane [PAH/PSS]1PAH/PSSMA composed of only two bilayers exhibited 91.4% Na2SO4 rejection and allowed solution flux of 28.6L/m2h at 0.2MPa. The solution flux increased to 106.6L/m2h at 0.8MPa, meanwhile, no obvious decrease in Na2SO4 rejection was observed.
Fabrication and Performance of a Low Operating Pressure Nanofiltration Poly(vinyl Chloride) Hollow Fiber Membrane

Jian-hua Wang,Yue-li Wu,Yong-hua Zhang,Bao-ku Zhu,You-yi Xu

DOI: https://doi.org/10.1007/s10118-014-1374-4

2014-01-01

Abstract:A low operating pressure nanofiltration membrane is prepared by interfacial polymerization between m-phenylenediamine(MPDA) and trimesoyl chloride(TMC) using PVC hollow fiber membrane as supporting.A series of PVC nanofiltration membranes with different molecular weight cutoff(MWCO) can be obtained by controlling preparation conditions.Chemical and morphological characterization of the membrane surface was carried out by FTIR-ATR and SEM.MWCO was characterized by filtration experiments.The preparation conditions were investigated in detail.At the optimized conditions(40 min air-dried time,aqueous phase containing 0.5% MPDA,0.05% SDS and 0.6% acid absorbent,oil phase containing 0.3% TMC,and 1 min reaction time),under 0.3 MPa,water flux of the gained nanofiltration membrane reaches 17.8 L/m2·h,and the rejection rates of methyl orange and MgSO4 are more than 90% and 60%,respectively.
Optimal Design of Nanofiltration System for Surface Water Treatment

Fei Bi,Haiyang Zhao,Zhijun Zhou,Lin Zhang,Huanlin Chen,Congjie Gao

DOI: https://doi.org/10.1016/j.cjche.2016.05.012

IF: 3.8

2016-01-01

Chinese Journal of Chemical Engineering

Abstract:Both reverse osmosis(RO) and nanofiltration(NF) membranes have been increasingly used for water purification and desalination. However, the salt rejection of NF membranes is quite different from that of RO membranes,which makes a significant distinction in their process designs. This work started from the performance investigation of a single NF membrane element and then focused on the process design of the NF system for surface water treatment. In experimental tests, it was found that the observed rejection of the NF element becomes nearly constant when the concentrate flow is large enough, while the membrane flux of the NF element is quite stable regardless of the water flow across the membrane surface. These findings can be used to instruct the process design of the NF system for surface water treatment. In process design, a two-stage arrangement is sufficient for the NF system to reach the highest water recovery, while the RO system requires a three-stage arrangement.
Preparation and Characterization of an Amphiphilic Polyamide Nanofiltration Membrane with Improved Antifouling Properties by Two-Step Surface Modification Method

Huimin Ruan,Bin Li,Jianbing Ji,Arcadio Sotto,Bart Van der Bruggen,Jiangnan Shen,Congjie Gao

DOI: https://doi.org/10.1039/c8ra00637g

IF: 4.036

2018-01-01

RSC Advances

Abstract:Membrane fouling is an urgent problem needing to be solved for practical application of nanofiltration membranes. In this study, an amphiphilic nanofiltration membrane with hydrophilic domains as well as low surface energy domains was developed, to integrate a fouling-resistant defense mechanism and a fouling-release defense mechanism. A simple and effective two-step surface modification of a polyamide NF membrane was applied. Firstly, triethanolamine (TEOA) with abundant hydrophilic functional groups was grafted to the membrane surface via reacting with the residual acyl chloride group of the nanofiltration membrane, making the nanofiltration membranes more hydrophilic; secondly, the 1H,1H,2H,2H-perfluorodecyltrichlorosilane (PFTS), well-known as a low surface energy material, was covalently grafted on the hydroxyl functional groups through hydrogen bonding. Filtration experiments with model foulants (bovine serum albumin (BSA) protein solution, humic acid solution (HA) and sodium alginate solution (SA)) were performed to estimate the antifouling properties of the newly developed nanofiltration membranes. As a result of surface modification proposed in this study the antifouling properties of an amphiphilic modified F-PA/PSF membrane were enhanced more than 10% compared to the PA/PSF specimen in terms of flux recovery ratio.
Designing nanofiltration hollow fiber membranes based on dynamic deposition technology

Qian Wang,Tian-Dan Lu,Xiang-Yu Yan,Liu-Lin Zhao,Hang Yin,Xin-Xin Xiong,Rongfei Zhou,Shi-Peng Sun

DOI: https://doi.org/10.1016/j.memsci.2020.118336

IF: 9.5

2020-09-01

Journal of Membrane Science

Abstract:In this work, dynamic deposition technology was adopted to fabricate nanofiltration (NF) hollow fiber membrane, which can reduce water transport resistance to break trade-off effect and detect membrane performance in real-time. Firstly, polyimide hollow fiber substrates with high mechanical strength were designed by adjusting dope composition and spinning conditions. It was found that using pure n-methyl-2-pyrrolidinone as intermediate flow between dope and coagulant bath can keep balance of phase inversion to fabricate substrate with full spongy pores and thick thickness. Then, ZrO2 sol of 45 nm in size was deposited on substrate to prepare the dynamic membrane and the polyacrylic acid (PAA) was utilized to stabilize the ZrO2 layer and improve hydrophilicity and negative charge of membranes. The resultant membrane owns an amazing pure water permeability (PWP) of 32.6 Lm−2h−1bar−1 with a high rejection to Na2SO4 (93.4%) and various pharmaceuticals (>90%). This work may provide insightful guidelines to design robust hollow fiber NF membranes with straightforward and scalable strategies.

engineering, chemical,polymer science
Pore Size Tailoring from Ultrafiltration to Nanofiltration with PVC-g-PDMA Via Rapid Immersion Thermal Annealing

Ming-Yong Zhou,Li-Feng Fang,Chuang-Chao Sun,Chun-Er Lin,Bao-Ku Zhu,Jiang-Hua Chen

DOI: https://doi.org/10.1016/j.memsci.2018.10.060

IF: 9.5

2019-01-01

Journal of Membrane Science

Abstract:Different from the typical interfacial polymerization for nanofiltration membrane fabrication, we proposed a novel method to prepare charged nanofiltration membrane via rapid immersion thermal annealing process with the ultrafiltration membrane, which was prepared from the amphiphilic copolymer, poly(vinyl chloride)-g-poly (2-(dimethylamino) ethyl methacrylate) (PVC-g-PDMA) via non-solvent induced phase separation. The pore structures and chemical properties of the membranes, and annealing conditions including the media where the membrane was annealed, annealing temperature and time, were investigated in detail. It is found that the porous separation layer was collapsed to be a stable, defect-free, and smooth film as the dense separation layer of nanofiltration membrane when it was annealed in n-heptane above its glass transition temperature (Tg) for only 1 min while the pore size cutoff was tailored from 20 nm to 2 nm. Salt rejections were in the order of MgCl2> NaCl > MgSO4> Na2SO4 at neutral condition due to Donnan repulsion, indicating a typical positively charged nanofiltration membrane. Overall, this rapid immersion thermal annealing process provides a facile and effective strategy to tailor ultrafiltration membrane toward nanofiltration applications for amphiphilic copolymer based membranes.
Revealing Key Structural and Operating Features on Water/salts Selectivity of Polyamide Nanofiltration Membranes by Ensemble Machine Learning

Xuanchao Ma,Dan Lu,Jiancong Lu,Yukun Qian,Shun Zhang,Zhikan Yao,Lijun Liang,Zhilin Sun,Lin Zhang

DOI: https://doi.org/10.1016/j.desal.2022.116293

IF: 11.211

2023-01-01

Desalination

Abstract:Nanofiltration (NF) plays an increasingly central role in water/salts separation, which puts forward tailored requirements on NF membranes in a variety of application scenarios. However, the ambiguous separation mechanisms of NF including membrane structure parameters and operating conditions hinder the rational design of versatile NF membranes. Herein, machine learning was used to explore the correlation between membrane structure parameters and operating conditions with water/salts selectivity, and reveal the importance of the diverse features based on literature data. Two structural features of polyamide NF membrane (pore radius and zeta potential) and two operating parameters (pressure and feed concentration) were typically extracted and associated with water/salts selectivity. Random Forest and XGBoost models were employed to learn from relevant variables and assess their importance. The results showed that membrane structure parameters attached more importance to water/salts selectivity than that of operating conditions accompanying the variable influence for different typed salts, where symmetrical salts were mainly governed by size sieving while Donnan exclusion for asymmetrical salts. Structure-performance relationships between pore radius, zeta potential and diverse water/salts selectivity were established using partial dependence plot analysis. It is anticipated that the constructed comprehensive insights can be further leveraged to tackle performance modulation and oriented design of multi-scenarios NF membranes.
Machine learning for layer-by-layer nanofiltration membrane performance prediction and polymer candidate exploration

Chen Wang,Li Wang,Hanwei Yu,Allan Seo,Zhining Wang,Saeid Rajabzadeh,Bing-Jie Ni,Ho Kyong Shon

DOI: https://doi.org/10.1016/j.chemosphere.2023.140999

IF: 8.8

2023-12-29

Chemosphere

Abstract:In this study, machine learning-based models were established for layer-by-layer (LBL) nanofiltration (NF) membrane performance prediction and polymer candidate exploration. Four different models, i.e., linear, random forest (RF), boosted tree (BT), and eXtreme Gradient Boosting (XGBoost), were formed, and membrane performance prediction was determined in terms of membrane permeability and selectivity. The XGBoost exhibited optimal prediction accuracy for membrane permeability (coefficient of determination (R 2 ): 0.99) and membrane selectivity (R 2 : 0.80). The Shapley Additive exPlanation (SHAP) method was utilized to evaluate the effects of different LBL NF membrane fabrication conditions on membrane performances. The SHAP method was also used to identify the relationships between polymer structure and membrane performance. Polymers were represented by Morgan fingerprint, which is an effective description approach for developing modeling. Based on the SHAP value results, two reference Morgan fingerprints were constructed containing atomic groups with positive contributions to membrane permeability and selectivity. According to the reference Morgan fingerprint, 204 potential polymers were explored from the largest polymer database (PoLyInfo). By calculating the similarities between each potential polymer and both reference Morgan fingerprints, 23 polymer candidates were selected and could be further used for LBL NF membrane fabrication with the potential for providing good membrane performance. Overall, this work provided new ways both for LBL NF membrane performance prediction and high-performance polymer candidate exploration. The source code for the models and algorithms used in this study is publicly available to facilitate replication and further research. https://github.com/wangliwfsd/LLNMPP/

environmental sciences
Optimizing dual-layer composite membranes with functionalized CNT loadings using response surface methodology

Fatemeh Gholamzadeh Moghadam,Toraj Mohammadi,Amir Atabak Asadi

DOI: https://doi.org/10.2166/wst.2024.285

IF: 2.43

2024-08-20

Water Science & Technology

Abstract:In this study, we optimized double-layer composite membranes comprising polyethersulfone (PES) and polyamide (PA) using response surface methodology (RSM). We assessed the impact of PES, piperazine (PIP), and trimesoyl chloride (TMC) concentrations, and interfacial polymerization (IP) reaction time on nanofiltration (NF) membrane performance, aiming to enhance pure water flux (PWF) and salt rejection. Optimal parameters for maximum PWF and salt rejection were determined: PES concentration at 14.0 wt%, PIP concentration at 1.5 w/v%, TMC concentration at 0.2 w/v%, and reaction time at 45 s. In addition, we improved membrane performance by incorporating functionalized multi-walled carbon nanotubes (f-MWCNTs) into the PES ultrafiltration substrate, enhancing hydrophilicity and porosity. The resulting PA NF membrane developed on a substrate containing 0.15 wt% f-MWCNT (TFNC) exhibited a PWF of 11.84 LMH/bar, surpassing the PWF of the same NF membrane on an unloaded substrate (TFC) by approximately 20%, while maintaining nearly identical salt rejection levels. Salt rejection followed the order: Na2SO4 > MgSO4 > NaCl, suggesting Donnan-exclusion mechanisms primarily governed the separation process due to repulsion forces between the negatively charged membrane surface and anions.

environmental sciences,engineering, environmental,water resources
Composite Nanofiltration Membranes from Polyacrylonitrile and Poly (N, N-Dimethylaminoethyl Methacrylate)-Grafted Silica Nanoparticles

Suo-Hong Zhi,Bo Zhang,Yun Wang,Yun-Lian Zhang,Guo-Jun Zhou,Ran Deng,Ling-Shu Wan,Zhi-Kang Xu

DOI: https://doi.org/10.1142/9789813228177_0111

2018-01-01

Abstract:As a membrane process between ultraflitration (UF) and reverse osmosis (RO) nanofiltration is widely used in wastewater treatment, dye separation and desalination for its energy-efficient process. Layer-by-Layer (LbL) self-assembly technique is one of effective approaches to nanofiltration layer on support membrane via alternate deposition of building blocks by various non-covalent interactions. In order to extend the applications and improve the performance of LbLnanofiltration membrane, we induce organic-inorganic hybrid nanoparticles as the building block to fabricate nanofiltration composite membranes and focus on the effect of hybrid nanoparticles on self-assemble behavior, membrane structure and separation performance. Atom transfer radical polymerization (ATRP) initiator is anchored onto the surface of silica nanoparticles and initiate polymerization of N, N-dimethylaminoethyl methacrylate (DMAEMA). The PAN-based composite membranes are fabricated by LbL assembling of quaternized PDMAEMA@SiO2 (PMETAI@SiO2) nanoparticles and PAA on hydrolyzed PAN ultrafiltration support membranes. The results indicate that the water flux has a maximum value with pH varying from 2.0 to 6.5. On the other hand, it shows opposite tendency with the increase of ion strength. The membrane exhibits high rejection of Congo red, which is contributed to small pore size and Donan effect.
Synthesizing high performance robust PSf loose nanofiltration membranes through nanobubble-assisted pore-forming

Zongrui Song,Yujie Wu,Junjie Lv,Yanhong Ji,Mohammad Younas,Benqiao He

DOI: https://doi.org/10.1016/j.desal.2024.118274

IF: 11.211

2024-11-07

Desalination

Abstract:Loose nanofiltration (LNF) membranes have extensive applications in precision separation processes, however, synthesizing highly permselective LNF membranes is still a considerable obstacle. Nanobubble-assisted pore-forming method was adapted to prepare a highly perm-selective LNF membrane for the first time in this work, using polysulfone (PSf) as the membrane-forming material, azodicarbonamide (AC) as the reactive pore-forming agents, and NaOH solution as the coagulation and immersion baths. By leveraging nano-bubbles produced through the reaction between AC and NaOH without adding other pore-forming agents, the membrane-forming process of PSf was regulated. It was found that the PSf LNF membranes prepared in NaOH-solution coagulation and immersion baths exhibited significantly enhanced permeation performance without compromising the rejection. These results suggested that the coagulation and immersion post-treatment processes under NaOH solution had a great effect upon the structure and the property of the membranes. The LNF membrane prepared from 20 wt% PSf casting solution with 8 wt% AC achieved a permeation flux of 188.7 L m −2 h −1 , and a Congo red (CR, Mw =696 Da) rejection of over 99 %, while a rejection of NaCl below 7 %, showing a good separation for the CR/NaCl mixed solution. Additionally, the membrane exhibited favorable mechanical properties, with a tensile strength as high as 6.5 MPa and a fracture elongation reaching as much as 32.3 %. This work provided a novel approach for producing high-performance LNF membranes in treating dye wastewater.

engineering, chemical,water resources
Pilot-scale fabrication of nanofiltration membranes and spiral-wound modules

Bo-Zhi Chen,Xiaohui Ju,Ning Liu,Chang-Hui Chu,Jin-Peng Lu,Chen Wang,Shi-Peng Sun

DOI: https://doi.org/10.1016/j.cherd.2020.06.011

2020-01-01

Abstract:Few studies have reported on the detail of the mass production process of nanofiltration (NF) membranes and modules due to technical confidentiality. This work presents a procedure of fabrication of NF membranes and modules on the pilot scale. Thin film composite (TFC) NF flat-sheet membranes of 300 mm width were continuously fabricated via custom-designed equipment. The fabrication parameters and their effects on NF performance were systematically investigated. The optimized conditions parameters were achieved for excellent NF modules' performance. The modules show over 75 L m(-2) h(-1) flux at 6 bar and over 95% MgSO4 rejection. This study may provide insightful guidelines for the scale-up of NF membranes for water treatment and other applications. (C) 2020 Institution of Chemical Engineers. Published by Elsevier B.V. All rights reserved.
Designing Scalable Dual-Layer Composite Hollow Fiber Nanofiltration Membranes with Fully Cross-Linked Ultrathin Functional Layer

Zhen-Yuan Wang,Yi-Chen Wang,Wei-Jian Wang,Sheng-Nan Tao,Ya-Feng Chen,Mengmeng Tang,Dan-Dan Shao,Weihong Xing,Shi-Peng Sun

DOI: https://doi.org/10.1016/j.memsci.2021.119243

IF: 9.5

2021-01-01

Journal of Membrane Science

Abstract:The treatment of industrial wastewater containing complex foulants demands high efficiency yet cost-effective separation process. The composite hollow fiber nanofiltration membranes suffer from tedious fabrication procedures, impeding the large volume fabrication and application. Herein, we reveal a very simplified designing strategy by polyelectrolyte modification of the co-extruded polyimide/polyethersulphone dual-layer hollow fibers with hierarchical structure and chemistry. The active layer?s thickness of the dual-layer hollow fiber substrate is only 800 nm, the thinnest in literature. Compared to integral active single layer hollow fiber, the ultrathin active layer not only leads to over 4 times increase in mechanical flexibility and tenfold reduction in material cost but also enables fully chemical transition from imide to cross-linked polyamide, minimizing the intrinsic hydrolysis tendency of active material. The optimized membranes with a well-defined pore radius of 0.23 nm have 93?95% rejection to Mg2+ and Ca2+ and PWP of 9.1 LMH/bar. Moreover, the composite membranes exhibit backwash ability and stability in the heated feed solutions, which meets the demand for direct treatment of industrial effluents. This work paves the way for the large volume fabrication and application of hollow fiber nanofiltration membranes for treating municipal water, industrial wastewater, and other applications.
Alginate Hydrogel Assisted Controllable Interfacial Polymerization for High-Performance Nanofiltration Membranes

Zhao-Yu Ma,Yu-Ren Xue,Zhi-Kang Xu

DOI: https://doi.org/10.3390/membranes11060435

IF: 4.562

2021-01-01

Membranes

Abstract:The deepening crisis of freshwater resources has been driving the further development of new types of membrane-based desalination technologies represented by nanofiltration membranes. Solving the existing trade-off limitation on enhancing the water permeance and the rejection of salts is currently one of the most concerned research interests. Here, a facile and scalable approach is proposed to tune the interfacial polymerization by constructing a calcium alginate hydrogel layer on the porous substrates. The evenly coated thin hydrogel layer can not only store amine monomers like the aqueous phase but also suppress the diffusion of amine monomers inside, as well as provide a flat and stable interface to implement the interfacial polymerization. The resultant polyamide nanofilms have a relatively smooth morphology, negatively charged surface, and reduced thickness which facilitate a fast water permeation while maintaining rejection efficiency. As a result, the as-prepared composite membranes show improved water permeance (~30 Lm−2h−1bar−1) and comparable rejection of Na2SO4 (>97%) in practical applications. It is proved to be a feasible approach to manufacturing high-performance nanofiltration membranes with the assist of alginate hydrogel regulating interfacial polymerization.
Impact of support pore properties on the performance of layer-by-layer self-assembly nanofiltration membrane

Juan Luo,Chenjun Dong,Rongrong He,Chang Liu,Tao He

DOI: https://doi.org/10.1016/j.desal.2023.116596

IF: 11.211

2023-04-08

Desalination

Abstract:This paper investigates the impact of the porous structure of the support on the permselectivity and backwash resistance of Layer-by-Layer (LBL) nanofiltration (NF) membranes. Four different polyethersulfone (PES) hollow fiber membranes with varying pore sizes were coated with poly(allylamine hydrochloride)/poly(sodium-4-styrenesulfonate) (PAH/PSS) polyelectrolyte pairs. The study found that adjusting the number of bilayers in the coating process enabled the production of LBL membranes with similar molecular weight cut-off (MWCO) around 250 Da and high Mg 2+ rejection of 95 %. However, Na 2 SO 4 rejection decreased as the number of bilayers increased, as the positively charged PAH overcompensated. The study also found that the pore size of the support did not significantly impact the backwash resistance of the LBL membranes, indicating that the polyelectrolyte chains can penetrate through the pores of the supports regardless of pore size. This finding can guide the design of suitable supports for LBL NF membranes with tailored performances.

engineering, chemical,water resources
Surface and Interface Engineering for Advanced Nanofiltration Membranes

Guo Bian-Bian,Zhu Cheng-Ye,Xu Zhi-Kang

DOI: https://doi.org/10.1007/s10118-022-2654-z

2022-01-01

Chinese Journal of Polymer Science

Abstract:Nanofiltration has been attracting great attention in alleviating the global water crisis because of its high efficiency, mild operation, and strong adaptability. Over decades, it remains a challenge to break the upper limit of performance and establish the formation-structure-property relationship for nanofiltration membranes. This feature article summarizes our recent progress in the preparation of high-performance thin-film composite (TFC) nanofiltration membranes, focusing on the mussel-inspired deposition method and the optimized interfacial polymerization (IP). By accelerating the oxidation of polydopamine and equilibrating the rate of aggregation and deposition processes, the mussel-inspired deposition method realizes the rapid and uniform formation of selective coatings or nanofilms. Diverse deposition systems endow the selective layer with rich chemical structures and easy post-functionalization, highlighting its potential in water treatment. As for optimizing the conventional IP, the rapid polycondensation of amine and acid chloride groups is slowed down to enable the controllability of IP at the water-organic interface. The homogeneity and integrity of the TFC membranes are improved by constructing a uniform reaction platform and introducing a viscous medium to control the amine diffusion, which facilitates the water permeability and promotes the separation efficiency. We have proposed a series of practical strategies for improving TFC membranes and might provide more inspiration for other nanofiltration techniques.
Fabrication of Loose Nanofiltration Membranes with High Rejection Selectivity Between Natural Organic Matter and Salts for Drinking Water Treatment

Zhihai He,Kunpeng Wang,Yanling Liu,Ting Zhang,Xiaomao Wang

DOI: https://doi.org/10.3390/membranes12090887

IF: 4.562

2022-01-01

Membranes

Abstract:Loose nanofiltration (LNF) membranes with a molecular weight cut-off (MWCO) of about 1000 Da and high surface negative charge density have great application potential for drinking water treatment pursuing high rejection selectivity between natural organic matter (NOM) and mineral salts. This study was conducted to exploit the novel method coupling non-solvent induced phase separation (NIPS) and interfacial polymerization (IP) for the preparation of high-performance LNF membranes. A number of LNF membranes were synthesized by varying the polyethersulfone (PES) and piperazine (PIP) concentrations in the cast solution for the PES support layer preparation. Results showed that these two conditions could greatly affect the membrane water permeance, MWCO and surface charge. One LNF membrane, with a water permeance as high as 23.0 ± 1.8 L/m2/h/bar, when used for the filtration of conventional process-treated natural water, demonstrated a rejection of NOM higher than 70% and a low rejection of mineral salts at about 20%. Both the mineral salts/NOM selectivity and permselectivity were superior to the currently available LNF membranes as far as the authors know. This study demonstrated the great advantage of the NIPS–IP method for the fabrication of LNF membranes, particularly for the advanced treatment of drinking water.
Machine learning based prediction and optimization of thin film nanocomposite membranes for organic solvent nanofiltration

Chen Wang,Li Wang,Allan Soo,Nirenkumar Bansidhar Pathak,Ho Kyong Shon

DOI: https://doi.org/10.1016/j.seppur.2022.122328

IF: 8.6

2023-01-01

Separation and Purification Technology

Abstract:In this study, machine learning was used to form prediction models for thin film nanocomposite (TFN) organic solvent nanofiltration (OSN) membrane performance evaluation in terms of relative permeability (RP) and relative selectivity (RS). Twenty references including 9252 data points were collected to form four different models: linear, support vector machine (SVM), boosted tree (BT), and artificial neural network (ANN). Among the four models, BT exhibited optimal prediction accuracy in terms of root mean square error (RMSE) and coefficient of determination (R2) values for membrane RP (RMSE: 0.295, R2: 0.918) and RS (RMSE: 0.053, R2: 0.849) performance prediction. Parameter contribution analysis indicated that nanoparticle loading, amine concentration, chloride concentration, water contact angle, solvent viscosity, and molar volume are the main parameters influencing RP performance. For RS performance, nanoparticle loading, amine concentration, chloride concentration, and solute molecular weight play important roles. Partial dependence analysis indicated that the optimal conditions for TFN-OSN membrane fabrication are nanoparticle loading less than 5 wt%, the amine concentration around 2 wt%, and the chloride concentration around 0.15 wt%. In addition, membrane with super-hydrophilic or super-hydrophobic surface property exhibited higher RP performance based on different feed solvent types. Overall, this work introduces new ways both for TFN-OSN membrane performance prediction and for higher performance membrane design and development.

engineering, chemical
Development of high permeability nanofiltration membranes through porous 2D MOF nanosheets

Xiao-Gang Jin,Xiao-Kang Liang,Jia-Hao Liu,Jia-Wei Mo,Tian-Xiang Ren,Xiao-Hua Ma,Zhen-Liang Xu

DOI: https://doi.org/10.1016/j.cej.2023.144566

IF: 15.1

2023-09-01

Chemical Engineering Journal

Abstract:High-performance nanofiltration membrane is of great importance to alleviate the worldwide freshwater crisis. Recent studies have shown that the performance of nanofiltration membranes can be enhanced by optimizing the properties of the substrates. Substrates with large pores are favorable to mass transfer but difficult to prepare highly selective polyamide layers on them by interfacial polymerization reaction. Here we employed porous two-dimensional (2D) aluminum-metal organic framework (Al-MOF) nanosheets to tune the commercial Nylon microfiltration substrate, and then prepared polyamide nanofiltration membranes by interfacial polymerization. 2D Al-MOF nanosheets were chosen for the tuning material except for their obvious advantages of easy synthesis and structural stability, the most important thing was their high porosity, which provided additional water transport channels. The morphologies as well as the separation properties were analyzed systematically. The best-performing Nylon-2.5 TFC membrane achieved an ultrahigh permeability (42.4 L m−2 h−1 bar−1), 13 times that of a control (PES-0) TFC membrane prepared on commercial PES substrate under the same interfacial polymerization conditions while ensuring the high rejection of Na2SO4 (97.0%). Our work provides insights for optimizing substrate properties to prepare high-performance nanofiltration membranes.

engineering, chemical, environmental
Polymer Nanofiltration Membranes via Controlled Surface/Interface Engineering

Yan Lv,Yong Du,Shang-jin Yang,Jian Wu,Zhi-kang Xu

DOI: https://doi.org/10.11777/j.issn1000-3304.2017.17201

2017-01-01

Acta Polymerica Sinica

Abstract:Nanofiltration membranes occupy a crucial position in membrane technology due to their superiority of high separation efficiency and low energy cost, which are therefore widely applied in the field of water treatment, food and medicine, membrane bioreactor and petro chemistry. Most nanofiltration membranes are made from polymeric materials with composite structure containing a thin selective layer and a porous support layer. As the key of this structure, the selective layer can be fabricated via various methods such as interfacial polymerization, layer-by-layer assembly, surface coating and graft polymerization followed with crosslinking. However, it still remains a big challenge to precisely control the skin layer structures during interfacial polymerization process ascribed to its very fast reaction. We demonstrate that the interfacial property and the interfacial reactions can be well tuned via controlled surface/interface engineering, thus to control the fabrication and performance of the composite nanofiltration membranes. This review is aimed to summarize the most recent advances on polymeric composite nanofiltration membranes based on controlled surface/interface engineering mainly conducted in our group. On one hand, a tunable polymerization-deposition strategy is proposed to realize novel or functional selective layer. In these cases, dopamine and derivative polyphenol are employed to fabricate the selective layer with self-polymerization and deposition process tuned by additives, oxidant and contra-diffusion operation. Novel nanofiltration membranes with photocatalytic function are further achieved owing to the reactive moieties in the co-deposition layer. On the other hand, an interfacial property tailoring interfacial polymerization strategy is proved to obtain ultrathin and high-performance nanofiltration membranes. An intermediate layer is fabricated prior to traditional interfacial polymerization with excellent hydrophilicity and uniform structure, which help to homogenize the monomer concentration on substrate surface and control the release of monomers to achieve ultrathin polyamide layer. We believe that these advances will provide reliable methodological and theoretical foundation for the controllable fabrication of high performance composite nanofiltration membranes. Moreover, the challenges remained in this area are also presented, such as details of chemical reactions, reaction-structure-function relationship, optimization of methodology and development of basic theory, to point out the future research direction with the aim to push forward the studies in this area.

ANNOUNCEMENT: 2001 Best Paper Award Committee

Polyelectrolyte membranes prepared by dynamic self-assembly of poly (4-styrenesulfonic acid-co-maleic acid) sodium salt (PSSMA) for nanofiltration (I)

Fabrication and Performance of a Low Operating Pressure Nanofiltration Poly(vinyl Chloride) Hollow Fiber Membrane

Optimal Design of Nanofiltration System for Surface Water Treatment

Preparation and Characterization of an Amphiphilic Polyamide Nanofiltration Membrane with Improved Antifouling Properties by Two-Step Surface Modification Method

Designing nanofiltration hollow fiber membranes based on dynamic deposition technology

Pore Size Tailoring from Ultrafiltration to Nanofiltration with PVC-g-PDMA Via Rapid Immersion Thermal Annealing

Revealing Key Structural and Operating Features on Water/salts Selectivity of Polyamide Nanofiltration Membranes by Ensemble Machine Learning

Machine learning for layer-by-layer nanofiltration membrane performance prediction and polymer candidate exploration

Optimizing dual-layer composite membranes with functionalized CNT loadings using response surface methodology

Composite Nanofiltration Membranes from Polyacrylonitrile and Poly (N, N-Dimethylaminoethyl Methacrylate)-Grafted Silica Nanoparticles

Synthesizing high performance robust PSf loose nanofiltration membranes through nanobubble-assisted pore-forming

Pilot-scale fabrication of nanofiltration membranes and spiral-wound modules

Designing Scalable Dual-Layer Composite Hollow Fiber Nanofiltration Membranes with Fully Cross-Linked Ultrathin Functional Layer

Alginate Hydrogel Assisted Controllable Interfacial Polymerization for High-Performance Nanofiltration Membranes

Impact of support pore properties on the performance of layer-by-layer self-assembly nanofiltration membrane

Surface and Interface Engineering for Advanced Nanofiltration Membranes

Fabrication of Loose Nanofiltration Membranes with High Rejection Selectivity Between Natural Organic Matter and Salts for Drinking Water Treatment

Machine learning based prediction and optimization of thin film nanocomposite membranes for organic solvent nanofiltration

Development of high permeability nanofiltration membranes through porous 2D MOF nanosheets

Polymer Nanofiltration Membranes via Controlled Surface/Interface Engineering