Abstract:Background Traumatic coronoid deficiency with persistent elbow instability is a challenging condition. Autologous bone graft reconstruction is often associated with a range of additional clinical problems and the outcome is often unpredictable. The purpose of this study was to design a prosthetic device that can reconstruct coronoid deficiency of any height and to evaluate its mechanical properties using finite element analysis. Materials and Methods A customized coronoid prosthesis was designed based on image registration, automatic measurement and computer-aided design. After pilot study and sample size calculation, image data collected from six patients who underwent bilateral complete upper extremity CT scans were reconstructed. The test was divided into three groups: coronoid intact, prosthesis and autograft. Regan-Morrey type II and autologous olecranon osteotomy models were established. The prosthesis and autogenous olecranon were assembled to the coronoid base. Stress was applied axially along the proximal humeral diaphysis and implant micromotion and contact mechanics of the humeroulnar joint were measured at 30°, 45°, 60° and 90° of joint flexion respectively. Results At all flexion angles, the maximum stress on the coronoid articular surface was significantly reduced in the prosthesis and autograft groups, with the reduction being more significant in the latter ( P < 0.001). With increasing flexion, the maximum stress at the coronoid articular surface increased significantly after autograft reconstruction (7.2 to 68 MPa, P < 0.001), whereas the humeroulnar joint obtained a similar contact mechanics pattern to that of the control group after prosthetic reconstruction. As the flexion angle increased, the relative micromotion of both the prosthesis and autograft increased significantly (0.5-1.6 vs 0.2-1.2, P measure time < 0.001, P groups < 0.001). Contact pressure and center-of-force paths of the humeroulnar joint experience abrupt stress changes at approximately 60° of flexion. Conclusion The contact stress pattern in the humeroulnar joint is similar in prosthesis and intact coronoid groups. Autograft reconstruction increases contact stresses at the articular surface and alters the joint center-of-force path. The "stress surge phenomenon" in the humeroulnar joint surface before and after 60° of flexion may be one of the mechanisms of traumatic elbow degeneration.

Computer-Aided Autogenous Coronoid Process Graft Combined With Median and Unilateral Sagittal Split Osteotomy for Late Reconstruction of Condylar Fracture and Occlusion after Trauma

Application of CAD/CAM Techniques in Mandible Large-Scale Defect and Reconstruction with Vascularized Fibular Bone Graft

[Application of Computer Aided Design/computer Aided Manufactured Techniques in Mandible Defect Reconstruction].

[Application of Computer Aided Design-Computer Aided Manufacture Technique in Mandible Defect Reconstruction with Individual Titanium Prosthesis].

Computer-Assisted Condylar Reconstruction In Bilateral Ankylosis Of The Temporomandibular Joint Using Autogenous Coronoid Process

Immediate reconstruction of bilateral mandible defects: management based on computer-aided design/computer-aided manufacturing rapid prototyping technology in combination with vascularized fibular osteomyocutaneous flap.

Computer-assisted surgical planning and intraoperative navigation in the treatment of condylar osteochondroma

Late reconstruction of the complex orbital fractures with computer-aided design and computer-aided manufacturing technique

Primary Clinical Research of a Patient Specific Implant System for an Old Zygomaticomaxillary Complex Comminuted Fracture

Application of Computer-Assisted Design and Manufacturing-Fabricated Artificial Bone in the Reconstruction of Craniofacial Bone Defects

Computer-assisted surgical planning and simulation for condylar reconstruction in patients with osteochondroma.

CAD/CAM and Rapid Prototyped Titanium for Reconstruction of Ramus Defect and Condylar Fracture Caused by Mandibular Reduction

Cone-beam Computed Tomography Evaluation of the Maxillofacial Features of Patients with Unilateral Temporomandibular Joint Ankylosis Undergoing Condylar Reconstruction with an Autogenous Coronoid Process Graft

Free grafting of autogenous coronoid process for condylar reconstruction in patients with temporomandibular joint ankylosis.

Computer-assisted virtual technology in intracapsular condylar fracture with two resorbable long-screws.

Application of CAD/CAM-assisted Technique with Surgical Treatment in Reconstruction of the Mandible.

Finite element analysis of a customized coronoid prosthesis for traumatic coronoid deficiency

Autogenous Coronoid Process Grafts for Condylar Reconstruction in Temporomandibular Joint Ankylosis

The clinic evaluation of condylar reconstruction by using autogenous coronoid process in arthroplasty

Application of EH compound artificial bone material combined with computerized three-dimensional reconstruction in craniomaxillofacial surgery.

Secondary reconstruction of unilateral mandible defect using CAD/CAM-prefabricated titanium mesh combined with autogenous iliac cancellous bone grafts