Patterns of puberal development in Sahiwal and Brahman cross bulls in tropical Australia. I. Growth and semen characteristics.

S. Wildeus,R. Holroyd,K. Entwistle

DOI: https://doi.org/10.1016/0093-691X(84)90456-4

IF: 2.923

1984-10-01

Theriogenology

Abstract:

What problem does this paper attempt to address?

First‐trimester maternal dried blood Down syndrome screening marker levels in early pregnancy loss

D. Krantz,T. Hallahan,S. Ishack,V. Macri,J. Macri

DOI: https://doi.org/10.1002/pd.1574

2006-12-01

Prenatal Diagnosis

Abstract:To determine the association of free beta hCG and PAPP‐A measured during first‐trimester Down syndrome risk assessment with early pregnancy loss when blood is drawn prior to scheduled ultrasound.
Weigh-in-Motion Systems Review: Methods for Axle and Gross Vehicle Weight Estimation

Enrico Oliveira Rocheti,Rodrigo Moreira Bacurau

DOI: https://doi.org/10.1109/access.2024.3461653

IF: 3.9

2024-10-01

IEEE Access

Abstract:Weigh-In-Motion (WIM) systems dynamically measure vehicle weight, eliminating the need for vehicle stoppage on static scales. These systems are the most convenient way to identify overweight vehicles, one of the main causes of pavement damage. In order to be employed for direct enforcement, WIM systems must provide accurate and reliable measurements, which is very challenging, especially due to the dynamics of the moving vehicles. Aiming to overcome these challenges, various methods to estimate the weight of moving vehicles have been proposed. This paper first introduces a comprehensive overview of Weigh-In-Motion systems, addressing sensor types, road surface quality, weather conditions, and calibration methods. Moreover, the review addresses the impact of dynamic loads – oscillating forces exerted on the road surface by moving vehicles – on system accuracy, considering vehicle properties, speed, and road surface quality. The focus of this work are the different Weigh-In-Motion estimation methods, which were divided into two sequential stages: instantaneous axle load estimation and Gross Vehicle Weight (GVW) estimation. Although there is extensive research on WIM systems, comprehensive reviews that simultaneously categorize and explore both instantaneous axle load and GVW estimation techniques are lacking. By investigating these two sequential stages, this review highlights the limitations and challenges of implementing accurate WIM systems and indicates opportunities for further advances.

computer science, information systems,telecommunications,engineering, electrical & electronic
APPLICATION OF WEIGH-IN-MOTION (WIM) TECHNOLOGIES IN OVERWEIGHT VEHICLE ENFORCEMENT

S. Andrle,D. Kroeger,B. McCall

Abstract:A variety of Intelligent Transportation Systems (ITS) have been tested and proven to be practical solutions for commercial vehicle safety enforcement. Many systems have already been deployed in the USA and abroad. Many other systems are being tested and refined for future deployment. A system that has been in use for many years is weigh-in-motion (WIM). While the practice of weighing heavy trucks at highway speeds has been in use for several years, the systems continue to be refined in order to achieve optimal performance. This paper examines the feasibility and applications of weigh-in-motion systems in overweight vehicle enforcement in today's 24-hour per day environment.

Environmental Science,Engineering
Statistical Analysis of Site-specific Traffic Load Using Weigh-in-Motion Data

LIANG Xu,CHEN Bin,WANG Jian-wei,XIE Xu,LU Peng-zhen

2013-01-01

Journal of Civil Engineering and Management

Abstract:This paper is concerned with statistical analysis of the traffic data and develoTP a site-specific traffic load model based on the weigh-in-motion( WIM) system installed in Hangzhou Shixiang Expressway Bridge. The traffic condition and vehicle loading are analyzed in terms of vehicle traffic volume,vehicle traffic composition,axle load spectrum and gross vehicle weight spectrum. The results show that: traffic flow has a strong tidal regularity; 2. 8% of the vehicles have their axles overloaded by 10 tons or above,the maximum axle weight is 39. 5 tons,the maximum gross vehicle weight is 115 tons,the problem of aggravated overloading in the small hours is serious. Two-axis vehicle's GVW showed a unimodal distribution,three-axis above the GVW are expressed as multimodal distribution,five-axis and six-axis vehicle 's GVW showed tri-modal distribution. In heavy-axled vehicles,overloading mainly occurs on the second and / or the third axles,which might compromise the integrity of the structures of the bridge and other infrastructures. The acquisition of characteristics of vehicle loads helTP to make fair assessments of the safety of the bridges in service in the area, assisting the control of overloaded vehicles and management of bridge safety.
Vehicle weigh-in-motion technology

Cheng Lu,Zhang Hongjian,Cao Xianghui

DOI: https://doi.org/10.3321/j.issn:0254-3087.2006.08.029

2006-01-01

Abstract:Along with the development of the highway transportation and trade, vehicle weigh-in-motion becomes the key technology and the trend of measuring traffic loads. The paper presents the structure of vehicle WIM system and four types of commonly used WIM sensors: bending plate sensor, piezoelectric sensor, load cell sensor and fiber optic sensor. The output signal of axle load in the WIM system is analyzed. Several algorithms used in vehicle WIM system, such as arithmetic averaging, neural network and system identification are deeply discussed. The future trend for WIM is also described.
Vehicle Weigh-in-Motion System Based on Soft Capacitive Weighing Sensor

程路,李青,张宏建

2008-01-01

Abstract:A novel vehicle WIM(Weigh-in-motion)system based on soft capacitive weighing sensor is proposed.A signal processing using Kelvin model is presented to overcome the effects of rubber mechanical properties on the dynamic weight signal.A number of experiments are performed and results turns out that with measurement error less than 10%,accuracy of this method is superior to the Ⅱ kind of WIM system(error of gross weight is ±15% when confidence is 95%) defined by ASTME1318—94.Both theoretic analysis and the experimental results prove that this system is feasible and convenient for traffic inspection.
Ultrastructural properties of collagen fibrils in rat intestine.

L. Klein,H. Eichelberger,M. Mirian,A. Hiltner

DOI: https://doi.org/10.3109/03008208309005613

Connective Tissue Research

Abstract:Collagen fibers (bundles of fibrils) of rat small intestine as observed by Nomarski differential interference contrast microscopy were densely packed in parallel undulating arrays. At the electron microscopical level the diameters of intestinal collagen fibrils increased gradually from 50 nm at three weeks of age to 80 nm at 12 months of age. At each age the fibril diameters were fairly uniform in size. At three weeks or six months of age collagen fibrils from stretched, salted samples were somewhat larger in diameter (12-16%) than those from unstretched, unsalted samples. A biaxial orientation existed between bundles of collagen fibrils at angles that varied from 32 degrees to 81 degrees with a mean of 60 degrees. Thus, intestinal collagen at the fibril level is aligned at varying angles to the longitudinal and circular directions of the intestine.
Wavelet domain analysis for identification of vehicle axles in the application of BWIM technology

C. J. Tan,H. Zhao,W. W. Xiao,Y. Z. Wang

DOI: https://doi.org/10.1201/b17063-91

2014-01-01

Abstract:This paper introduces a new bridge weigh-in-motion (BWIM) technology, which uses instrumented bridge as a large scale to identify axle weights of moving vehicles across the bridge through continuously collected bridge response. In the new BWIM system, efficient and accurate identification of vehicle axles is one of the critical issue for its successful application. However, field tests demonstrate that the collected signals from these transducers sometimes are difficult to identify. This paper presents a wavelet-based analysis of stain signals and shows the efficacy of using wavelets in pattern recognition of these signals. The wavelet-based algorithm was verified by the field tests on an approach span of the Fifth Huaihua Bridge, located in Huaihua, Hunan, China. Field tests demonstrate that the wavelet domain analysis can effectively improve the efficiency and accuracy of axle identification on vehicle velocity, axle numbers and spacing.
A New Strategy for Dynamic Weighing in Motion of Railway Vehicles

Benedetto Allotta,Pierluca D'Adamio,Lorenzo Marini,Enrico Meli,Luca Pugi,Andrea Rindi

DOI: https://doi.org/10.1109/tits.2015.2477104

IF: 8.5

2015-12-01

IEEE Transactions on Intelligent Transportation Systems

Abstract:Weighing-in-motion (WIM) systems automatically perform the dynamic weighing of railway vehicles while the trains are running on the lines through a reasonable number of measurement points placed along the track. Such intelligent systems may overcome disadvantages in terms of costs and traffic management, which are typical of conventional static weighing systems. In this paper, we present an innovative algorithm for dynamical WIM applications aimed at estimating the axle and wheel loads of a generic train composition by means of indirect track measurements. The new approach allows the axle loads estimation at high vehicle speeds and can be customized for several input track measurements (rail shear, rail bending, vertical forces on the sleepers, etc.) as well as a combination of them. Consequently, it can be employed in different kinds of measurement stations. Having once studied the accuracy of the algorithm in estimating the loads, the same novel procedure is used to estimate the center-of-gravity position of the railway vehicle to avoid dangerous imbalances. The algorithm can receive as inputs both experimental and simulated data; simulated data are fundamental to test the algorithm (in terms of accuracy and robustness) under any operating conditions when experimental data are not available. A wide simulation campaign has been carried out to test the algorithm performances, obtaining promising results. In the near future, the proposed approach will be validated through suitable data coming from experimental tests organized in collaboration with Ansaldo STS and ECM SpA, which are the industrial partners of this research project.

engineering, electrical & electronic,transportation science & technology, civil
Investigation of Weigh-in-Motion Measurement Accuracy on the Basis of Steering Axle Load Spectra

Dawid Rys

DOI: https://doi.org/10.3390/s19153272

2019-07-25

Abstract:Weigh-in-motion systems are installed in pavements or on bridges to identify and reduce the number of overloaded vehicles and minimise their adverse effect on road infrastructure. Moreover, the collected traffic data are used to obtain axle load characteristics, which are very useful in road infrastructure design. Practical application of data from weigh-in-motion has become more common recently, which calls for adequate attention to data quality. This issue is addressed in the presented paper. The aim of the article is to investigate the accuracy of 77 operative weigh-in-motion stations by analysing steering axle load spectra. The proposed methodology and analysis enabled the identification of scale and source of errors that occur in measurements delivered from weigh-in-motion systems. For this purpose, selected factors were investigated, including the type of axle load sensor, air temperature and vehicle speed. The results of the analysis indicated the obvious effect of the axle load sensor type on the measurement results. It was noted that systematic error increases during winter, causing underestimation of axle loads by 5% to 10% for quartz piezoelectric and bending beam load sensors, respectively. A deterioration of system accuracy is also visible when vehicle speed decreases to 30 km/h. For 25% to 35% of cases, depending on the type of sensor, random error increases for lower speeds, while it remains at a constant level at higher speeds. The analysis also delivered a standard steering axle load distribution, which can have practical meaning in the improvement of weigh-in-motion accuracy and traffic data quality.
Influence of Trajectory and Dynamics of Vehicle Motion on Signal Patterns in the WIM System

Artur Ryguła,Andrzej Maczyński,Krzysztof Brzozowski,Marcin Grygierek,Aleksander Konior

DOI: https://doi.org/10.3390/s21237895

2021-11-26

Abstract:This paper presents the analyses of the signals recorded by the main sensors of a WIM test station in the cases of abnormal runs (i.e., runs with the changes of trajectory or the dynamics of vehicle motion). The research involved strain gauges which are used for measuring the weight of vehicles, inductive loops, as well as piezoelectric sensors used, inter alia, to detect twin wheels and to determine where a vehicle passes through a station. Since the designers intend the station to be able to implement the direct enforcement function, the selection of runs deviating from the normative ones constitutes an important issue for the assessment of the measurement reliability. The study considered the location of the trajectory of the runs, the dynamics (acceleration/braking) and the trajectory changes. The change in the amplitude and the value of the signal recorded by the strain gauges as a function of the location (position) of the contact between sensor and tires is a noteworthy observation which indicates the need to monitor this parameter in automatic WIM systems. Other tests also demonstrated the influence of the analysed driving parameters on the recorded results. However, by equipping the WIM station with a set of duplicate strain gauges, the measurement errors of the gross weight and axle loads are normally within the accuracy limits of class A(5) stations. Only in the case of accelerating/decelerating, does the error in measuring the load of a single axle reach several per cent.
Study on Dynamic Weighing System Base on Intelligent Algorithm

Jianfeng Li,Lifang Zhou,Qingqing Wang

DOI: https://doi.org/10.1109/icca.2007.4376459

2007-01-01

Abstract:Technology of dynamic weighing is an effective way to solve the problem of overloaded vehicles. The entire process of dynamic weighing is presented in this paper. The model of dynamic weighing system is discussed by the discrete wavelet transform to filter noise and the genetic algorithm to filter the dynamic load which can not be filtered through common method. To solve the amplitude change of dynamic load, multi-segments curve fit based on genetic algorithm is proposed. The simulation to actual data of dynamic weighing verifies the validity.
Endobronchial ultrasound‐guided transbronchial needle aspiration diagnosis of mediastinal lymph node metastasis of mucinous adenocarcinoma: Arborizing stromal meshwork fragments as a diagnostic clue

Arbaz Samad,J. Peltola,M. Mitiek,J. Jessurun,J. Manivel,S. Pambuccian

DOI: https://doi.org/10.1002/dc.22816

2012-02-01

Diagnostic Cytopathology

Abstract:Endobronchial Ultrasound‐Guided Transbronchial Needle Aspiration (EBUS‐TBNA) is a reliable and accurate method for the diagnosis of mediastinal metastases in patients with pulmonary and extrathoracic neoplasms. We report the cytopathologic findings of a case of metastatic signet‐ring cell carcinoma with abundant extracellular mucin production in the mediastinal lymph nodes of a 41‐year‐old woman, who presented with nausea, abdominal pain, and weight loss. Imaging studies showed a renal mass, numerous lung nodules, and mediastinal and retroperitoneal lymphadenopathy. EBUS‐TBNA of level 4R and 7 lymph nodes showed abundant, thick, “clean” mucus with entrapped ciliated bronchial cells, rare histiocytes, and fragments of cartilage. No neoplastic cells could be identified in Diff‐Quik®‐stained smears during the rapid on‐site evaluation, but rare signet‐ring cells were identified in the Papanicolaou‐stained smears and cellblock sections. A distinctive feature of the aspirates was the presence of large branching (arborizing), “spidery” stromal fiber meshwork fragments. These stained metachromatically (magenta) with Romanowsky‐type stains and cyanophilic to orangeophilic with Papanicolaou stains and showed occasional attached bland spindle cells, but had no capillary lumina or CD31‐staining endothelial cells. The tumor cells were strongly and diffusely positive for CEA, CDX2, CK7, CK20, and MUC2, supporting the diagnosis of a metastatic signet‐ring cell adenocarcinoma, most likely of gastrointestinal origin. We believe that the presence of the large spidery stromal fiber fragments is a useful clue to the presence of a mucinous neoplasm in EBUS‐TBNA and allows the differentiation of the neoplastic mucus from contaminating endobronchial mucus. Diagn. Cytopathol. 2013;41:896–900. © 2012 Wiley Periodicals, Inc.
Capacitive Flexible Weighing Sensor for WIM System

CHENG Lu,LI Qing,ZHANG Hong-jian

DOI: https://doi.org/10.3321/j.issn:0367-6234.2009.08.031

2009-01-01

Abstract:A capacitive flexible weighing sensor is proposed to perform the weight-in-motion measurement of vehicles,and its static characteristic is studied. The effects of forced area and time are analyzed. The dynamic behavior of the sensor is modeled using four-element model because of the viscoelasticity of rubber materials of the sensor. Experiments are performed and the results show that the error of gross weight measurement for vehicles is less than 10%,which is superior to the precision of Ⅰ kind of WIM system (gross weight error of ±10% with confidence of 95%) defined by ASTME1318-02. Theoretic analysis and numerical results demonstrate that the proposed method for weigh-in-motion measurement is feasible and convenient for traffic inspection.
Assessing Vehicle Wandering Effects on the Accuracy of Weigh-in-Motion Measurement Based on In-Pavement Fiber Bragg Sensors through a Hybrid Sensor-Camera System

Xinyi Yang,Xingyu Wang,Joseph Podolsky,Ying Huang,Pan Lu

DOI: https://doi.org/10.3390/s23218707

IF: 3.9

2023-10-26

Sensors

Abstract:Weigh-in-motion (WIM) systems are essential for efficient transportation and monitoring parameters such as vehicle number, speed, and weight to ensure regulatory compliance and enhance road safety. Recently, WIM measurements using the Glass Fiber Reinforced Polymer Fiber Bragg Grating (GFRP-FBG) sensors have shown robustness and effectiveness. However, the accuracy of weight evaluation using the WIM systems based on GFRP-FBG sensors can be significantly influenced by the vehicle-wandering effect, which introduces uncertainties in wheel position determination and weight calculations. This paper assessed the impact of vehicle wandering on the accuracy of a WIM measurement system based on GFRP-FBG sensors by utilizing a new hybrid sensor-camera system that integrates roadside cameras and in-pavement GFRP-FBG sensors. The detailed methodology and framework of the developed hybrid system are introduced, followed by field testing on Highway I-94 in the United States. The field testing results indicate that by using the hybrid system, the wheel load detection accuracy of the WIM system based on GFRP-FBG sensors can be controlled to be a Type I or Type III WIM according to the ASTM 1318E-09 standard, with an average accuracy ranging from 87.83% to 94.65%. At the same time, when the wander distance is less than or equal to 9 cm, the developed WIM system proves to be very cost-effective as it only comprises two GFRP-FBG sensors, one temperature FBG sensor, and one camera. These findings indicate the practical potential to enhance the accuracy of WIM systems based on GFRP-FBG sensors designed for highways for low-coast, reliable, and accurate measurements by addressing vehicle wandering effects.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
The distribution patterns of sister chromatid exchanges in V79 Chinese hamster cells: relevance to genotoxicity studies.

G. Rainaldi,T. Mariani,A. Piras,M. Caligo,S. Simi,M. Valdrighi

Abstract:Sister chromatid exchanges (SCEs) are routinely used in genotoxic studies. The observations that some agents induce SCEs without altering the SCE distribution, while others disrupt such distribution, support the use of SCE distribution as a tool to distinguish between agents which damage DNA and agents which interfere with the replication machinery. In addition to that, it was found that compounds belonging to the latter group, are also able to induce gene amplification. Despite the mechanism by which the two phenomena could be associated is undefined, an aberrant induction of SCEs as a basis of gene amplification it must be taken into account.
Assessment of Factors Affecting Measurement Accuracy for High-Quality Weigh-in-Motion Sites in the Long-Term Pavement Performance Database

Syed Waqar Haider,Muhamad Munum Masud,Olga Selezneva,Dean J. Wolf

DOI: https://doi.org/10.1177/0361198120937977

2020-08-05

Abstract:Weigh-in-motion (WIM) is a primary technology used for monitoring and collecting vehicle weights and axle loads on roadways. Highway agencies collect WIM data for many reasons, including highway planning, pavement and bridge design, freight movement studies, motor vehicle enforcement, and regulatory studies. Therefore, the data collected at WIM systems must be accurate and represent actual field loadings. Several factors or field conditions can affect the WIM system accuracy (i.e., measurement error). The potential site-related factors include road geometry, pavement stiffness, pavement surface distresses, road roughness, and climate. The WIM calibration and equipment-related factors may include sensor type and array, calibration speed and speed points, and sensors’ age. The WIM data for Long-Term Pavement Performance (LTPP) research-quality sites were considered to estimate benchmark accuracies for different sensors and evaluate the effects of different factors on WIM measurement errors. These are the 35 sites with WIM calibration data that meet the ASTM E1318-09 error tolerances for Type I WIM systems and are consistently calibrated using the LTPP protocol with a complete set of supporting data about WIM site performance and WIM site conditions. The data for the LTPP research-quality sites showed that for the sensor arrays utilized, the best achievable total errors based on GVW are ±5% for load cell (LC), ±9% for bending plate (BP), and ±9.8% for the quartz piezo (QP) sensors. These accuracy levels for different sensor types provide highway agencies with the benchmark values demonstrating the practically achievable accuracy of WIM measurements after calibration for different WIM sensor types. Based on available data, WIM sensor accuracy can be significantly affected by climate, especially for QP and polymer piezo sensors. Also, the longitudinal roadway slope at a WIM site, sensor array, and speed points may significantly affect the WIM system accuracy.
Study on the accuracy of axle load spectra used for pavement design

Dawid Rys,Piotr Burnos

DOI: https://doi.org/10.1080/10298436.2021.1915492

2021-04-22

International Journal of Pavement Engineering

Abstract:Weigh-in-Motion (WIM) systems are used in order to reduce the number of overloaded vehicles. Data collected from WIM provide characteristics of vehicle axle loads that are crucial for pavement design as well as for the development of pavement distress prediction models. The inaccuracy of WIM data lead to erroneous estimation of traffic loads and in consequence inaccurate prediction of pavement distress process. The objective of the paper is to present a new methodology of heavy traffic axle load spectra (ALS) correction due to weighing errors (systematic and random) that occur in WIM systems. The theoretical solution which is proposed in the paper was validated successfully. The method enables correction of erroneous data to make traffic load statistics used for pavement design more reliable and precise, with no necessity to remove high number of records, as it is used in other methods. The practical meaning of the newly developed method was emphasised by analysis of the effect of relative and random error of WIM data on pavement fatigue life estimation, as well as on the estimated percentage of overloaded vehicles. Mechanistic-empirical approach (M-EPDG) was used for this purpose.

construction & building technology,engineering, civil,materials science, characterization & testing
A Capacitive Flexible Weighing Sensor and Weighing Measurement

Li Qing,Cheng Lu,Zhang Hongjian,Li Xiong,Shi Ge

2008-01-01

Abstract:With the development of the Highway Transportation and Business Trade, vehicle weigh-in-motion (WIM) technology has become a key technology and trend of measuring traffic loads. In this paper, a novel capacitive flexible weighing sensor which is light weight, smaller volume and easy to carry was applied in the vehicle WIM system. The dynamic behavior of the sensor is modeled using the Maxwell-Kelvin model because the materials of the sensor are rubbers which belong to viscoelasticity. A signal processing method based on the model is presented to overcome effects of rubber mechanical properties on the dynamic weight signal. The results showed that the measurement error is less than ±10%. All the theoretic analysis and numerical results demonstrated that appliance of this system to weigh in motion is feasible and convenient for traffic inspection.
Design of a Capacitive Flexible Weighing Sensor for Vehicle WIM System

Lu Cheng,Hongjian Zhang,Qing Li

DOI: https://doi.org/10.3390/s7081530

IF: 3.9

2007-01-01

Sensors

Abstract:With the development of the Highway Transportation and Business Trade, vehicle weigh-in-motion (WIM) technology has become a key technology and trend of measuring traffic loads. In this paper, a novel capacitive flexible weighing sensor which is light weight, smaller volume and easy to carry was applied in the vehicle WIM system. The dynamic behavior of the sensor is modeled using the Maxwell-Kelvin model because the materials of the sensor are rubbers which belong to viscoelasticity. A signal processing method based on the model is presented to overcome effects of rubber mechanical properties on the dynamic weight signal. The results showed that the measurement error is less than ±10%. All the theoretic analysis and numerical results demonstrated that appliance of this system to weigh in motion is feasible and convenient for traffic inspection.

Patterns of puberal development in Sahiwal and Brahman cross bulls in tropical Australia. I. Growth and semen characteristics.

First‐trimester maternal dried blood Down syndrome screening marker levels in early pregnancy loss

Weigh-in-Motion Systems Review: Methods for Axle and Gross Vehicle Weight Estimation

APPLICATION OF WEIGH-IN-MOTION (WIM) TECHNOLOGIES IN OVERWEIGHT VEHICLE ENFORCEMENT

Statistical Analysis of Site-specific Traffic Load Using Weigh-in-Motion Data

Vehicle weigh-in-motion technology

Vehicle Weigh-in-Motion System Based on Soft Capacitive Weighing Sensor

Ultrastructural properties of collagen fibrils in rat intestine.

Wavelet domain analysis for identification of vehicle axles in the application of BWIM technology

A New Strategy for Dynamic Weighing in Motion of Railway Vehicles

Investigation of Weigh-in-Motion Measurement Accuracy on the Basis of Steering Axle Load Spectra

Influence of Trajectory and Dynamics of Vehicle Motion on Signal Patterns in the WIM System

Study on Dynamic Weighing System Base on Intelligent Algorithm

Endobronchial ultrasound‐guided transbronchial needle aspiration diagnosis of mediastinal lymph node metastasis of mucinous adenocarcinoma: Arborizing stromal meshwork fragments as a diagnostic clue

Capacitive Flexible Weighing Sensor for WIM System

Assessing Vehicle Wandering Effects on the Accuracy of Weigh-in-Motion Measurement Based on In-Pavement Fiber Bragg Sensors through a Hybrid Sensor-Camera System

The distribution patterns of sister chromatid exchanges in V79 Chinese hamster cells: relevance to genotoxicity studies.

Assessment of Factors Affecting Measurement Accuracy for High-Quality Weigh-in-Motion Sites in the Long-Term Pavement Performance Database

Study on the accuracy of axle load spectra used for pavement design

A Capacitive Flexible Weighing Sensor and Weighing Measurement

Design of a Capacitive Flexible Weighing Sensor for Vehicle WIM System