Checking out the G(2)/M transition.

V. Smits,R. Medema

DOI: https://doi.org/10.1016/S0167-4781(01)00204-4

2001-05-28

Biochimica et Biophysica Acta

Abstract:

What problem does this paper attempt to address?

Characteristics of ultra-high performance lightweight concrete containing hollow glass microspheres under severe loading conditions

Mandip Dahal,Gebremicael Liyew,Hyeong-Ki Kim,Sukhoon Pyo

DOI: https://doi.org/10.1016/j.conbuildmat.2022.129312

IF: 7.4

2022-11-21

Construction and Building Materials

Abstract:The present study proposes the development of ultra-high performance lightweight concrete (UHPLC). Hollow glass microspheres (HGMS) were used as a lightweight material, and their pozzolanic activity was verified through different tests under multiple curing conditions. High volume of HGMS was incorporated into ultra high performance concrete (UHPC) matrix, and UHPLC with a compressive strength of 160 MPa and oven dry density of 1862 kg/m3 was developed. The UHPLC was exposed to temperatures up to 1000 °C and a coupled cycle of chloride penetration and carbonation. The developed UHPLC performed well in high temperature exposure tests, with the oven-cured samples showing around 10 % mass loss after 30 h exposure. Despite such reduction of density, the UHPLC did not show any significant degradation to chloride ions and carbonation. The experimental results show that the developed UHPLC is durable in terms of high temperature exposure and coupled loading of chloride penetration and carbonation.

construction & building technology,materials science, multidisciplinary,engineering, civil
Lightweight ultra-high-performance concrete (UHPC) with expanded glass aggregate: Development, characterization, and life-cycle assessment

Pengwei Guo,Weina Meng,Jiang Du,Lily Stevenson,Baoguo Han,Yi Bao

DOI: https://doi.org/10.1016/j.conbuildmat.2023.130441

IF: 7.4

2023-03-01

Construction and Building Materials

Abstract:Ultra-high-performance concrete (UHPC) has high mechanical strengths and durability, but its density and carbon footprint are usually high. This paper developed a lightweight UHPC with low cost, low carbon footprint, low energy consumption, low thermal conductivity, and high ductility, by using three types of lightweight ingredients: hollow glass microsphere (460 kg/m3), expanded glass aggregate (800 kg/m3), and polyethylene fibers (970 kg/m3). Underlying mechanisms were investigated through thermogravimetry, X-ray diffraction, and mercury intrusion porosimetry analyses. Results showed that the hollow glass microsphere reduced the thermal conductivity of concrete; the expanded glass aggregate mitigated shrinkage while enhancing compressive strengths and flexural properties of concrete through internal curing; and the polyethylene fibers promoted multiple cracks, increasing ductility and toughness of concrete. With 20 % hollow glass microsphere, 1.5 % polyethylene fiber, and 25 % expanded glass, UHPC mixtures were developed to achieve high compressive strength (>127 MPa) and high flexural strength (>21 MPa), while reducing the density by 20 % and carbon footprint by 16 % as well as embodied energy by 27 %.

construction & building technology,materials science, multidisciplinary,engineering, civil
Physical, Mechanical, and Microstructure Characteristics of Ultra-High-Performance Concrete Containing Lightweight Aggregates

Aref A Abadel,Aref A. Abadel

DOI: https://doi.org/10.3390/ma16134883

IF: 3.4

2023-07-08

Materials

Abstract:This study explores and enhances the resistance of an ultra-high-performance concrete (UHPC) to explosive spalling under elevated temperatures. This study investigates the impact of lightweight aggregates (LWAs) on the mechanical and microstructural properties of the UHPC. Various UHPC specimens were created by replacing silica sand with LWAs in percentages ranging from 0% to 30%. The evaluation of these specimens involved assessing their compressive and flexural strengths, density, mass loss, shrinkage, porosity, and microstructural characteristics using scanning electron microscopy (SEM). This study provides valuable insights by analyzing the influence of lightweight aggregates on the strength, durability, and microstructure of UHPC. The results reveal that incorporating LWAs in the UHPC improved its flowability while decreasing its density, as the percentage of LWAs increased from 5% to 30%. Including 30% LWA resulted in a mass loss of 4.8% at 300 °C, which reduced the compressive and flexural strengths across all curing durations. However, the UHPC samples subjected to higher temperatures displayed higher strength than those exposed to ambient conditions. The microstructure analysis demonstrated that the UHPC specimens with 30% LWA exhibited increased density due to continuous hydration from the water in the lightweight aggregate. The pore size distribution graph indicated that incorporating more of the LWA increased porosity, although the returns diminished beyond a certain point. Overall, these findings offer valuable insights into the influence of lightweight aggregates on the physical and strength characteristics of UHPC. This research holds significant implications for developing high-performance, lightweight concrete materials.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Compressive Strength and Chloride Resistance of Slag/Metakaolin-Based Ultra-High-Performance Geopolymer Concrete.

Yufei Zhang,Jiejing Chen,Jin Xia

DOI: https://doi.org/10.3390/ma16010181

IF: 3.4

2022-01-01

Materials

Abstract:Ultra-high performance geopolymer concrete (UHPGC) has been favored due to its excellent sustainability and outstanding mechanical properties. This study was conducted to explore the mechanical and durability properties of slag/metakaolin-based UHPGC with steel fibers reinforcement. The uniaxial compression test and rapid chloride migration test were conducted to measure the compressive strength and chloride penetration resistance of UHPGC. A total of nine groups of mixture proportions were designed and tested to investigate the influences of steel fiber dosage and sodium hydroxide (NaOH) solution concentration. The results showed that an increased steel fiber dosage and alkali concentration can improve compressive strength, and the maximum compressive strength can reach more than 140 MPa. In addition, the rapid chloride migration test showed that the chloride penetration resistance of the slag/metakaolin-based concrete was moderate, with a non-steady chloride migration coefficient ranging from 6.5 × 10−12 m2/s to 14.1 × 10−12 m2/s. The increase in steel fiber volume content slightly enlarged chloride penetration depth, while the higher concentration of sodium hydroxide solution was beneficial as it improved chloride penetration resistance. The results suggest that although ultra-high compressive strength can be achieved, the durability issues of steel fiber reinforced slag/metakaolin-based geopolymer concrete still need considerable attention.
Assessing durability properties of ultra-high performance concrete-class materials

Naveen Saladi,Luca Montanari,Igor De la Varga,Robert Spragg,Benjamin Graybeal

DOI: https://doi.org/10.1617/s11527-023-02244-3

2023-09-27

Materials and Structures/Materiaux et Constructions

Abstract:Ultra-high performance concrete (UHPC) is a class of concrete materials that has received significant attention from the infrastructure community due to its favorable mechanical and durability performance. As the use of UHPC in infrastructure projects is becoming more common, there is an increasing interest in identifying appropriate testing techniques to assess the durability properties of UHPC-class materials. The dense microstructure of UHPC-class materials and the presence of a high concentration of fiber reinforcement have made it difficult to rely on existing standard testing approaches for concrete durability assessment. This study explores the application of various conventional-concrete durability test methods to UHPC, including electrical resistivity (American Association of State Highway and Transportation Officials (AASHTO) TP 119-22), freeze–thaw (ASTM C666), water absorption (ASTM C1585), and rapid chloride migration test (NT BUILD 492). The selected tests are meant to qualify and quantify the microstructural penetrability of UHPC to ions and fluids, a surrogate property commonly used as an indicator of durability. The findings from this study indicate that electrical resistivity can be used as a durability indicator for UHPC-class materials. Moreover, strong correlation between electrical resistivity and the chloride migration coefficient is identified, a potential benefit given that chloride migration can be used to estimate service lives of UHPC-class materials. Other tests, including freeze–thaw and water absorption, although identifying the favorable performance of UHPC relative to conventional concrete, were unable to provide insightful information through which the performance of individual UHPCs could be differentiated.
Preparation and properties of ultra-high performance lightweight concrete

Huimin Pan,Shuaijun Yan,Qingxin Zhao,Dongli Wang

DOI: https://doi.org/10.1680/jmacr.22.00034

IF: 2.46

2022-07-27

Magazine of Concrete Research

Abstract:Based on orthogonal experiments, an ordinary Portland cement (OPC)-fly ash (FA)-silica fume (SF) ternary cementitious material system was developed. The ultra-high-strength lightweight concrete (UHPLC) with a strength exceeding 100 MPa was prepared using pottery sand (PS) and hollow glass microspheres (HGM) as the weight-reducing material and steel fibers as reinforcement. Through workability, apparent density, strength, and early autogenous shrinkage tests, as well as SEM examinations, the effect of various material parameters on the basic performance of UHPLC are investigated, and their mechanisms were explored. The results revealed the optimal mix ratio of OPC: FA: SF: PS: HGM =1: 0.200: 0.133: 0.533: 0.067, a water-binder ratio of 0.16, and the volume ratio of steel fibers of 2%. Under steam curing at 90°C for 48 h, the prepared UHPLC had an apparent density of 2031 kg/m 3 , compressive/flexural strengths of 112/16 MPa, a slump/expansion of 260/590 mm, and specific strength of 0.055, achieving the goal of lightweight and high strength. As the filler of composite materials, HGM can achieve lightweight and high strengthening of cement-based materials. HGM had a large water demand, increasing the autogenous shrinkage of UHPLC to a certain extent. The incorporation of steel fibers significantly increased the strength and apparent density of UHPLC, and its high elastic modulus inhibited the UHPLC shrinkage.

construction & building technology,materials science, multidisciplinary
Fracture behavior of ultra‐high performance lightweight concrete: In situ investigations using μ‐CT

Cristin Umbach,Bernhard Middendorf

DOI: https://doi.org/10.1002/cepa.2852

2023-12-01

ce/papers

Abstract:Abstract In various research projects at the University of Kassel, the concept of lightweight concrete has been combined with that of ultra‐high performance concrete (UHPC). Due to the high performance of the UHPC matrix, lightweight concretes (UHPLC) with strengths of 60‐130 MPa and bulk density of 1.5‐1.9 kg/m 3 were developed. This material can be used in many applications because of its low thermal conductivity, low weight and thus easy to transport, recyclable and can be prefabricated. Thus, it meets today's multifunctional requirements for building materials. The brittle material failure of UHPC without fibers is not observed with UHPLC. Instead, the concretes fail in hourglass shape under compressive stress, as seen in standard concretes. This constellation is not only responsible for the reduction of strength and Y‐modulus, but also predicts a ductile failure. For a better interpretation of the fracture behavior and fracture pattern, images of the UHPLC were taken in a highresolution computed tomography (μ‐CT) scanner. Between images, the sample was loaded and the load was kept constant during the measurement. The data was evaluated on the basis of a damage parameter, as well as crack openings during stable crack growth and the crack pattern after the maximum load was exceeded.
Strategy for preventing explosive spalling and enhancing material efficiency of lightweight ultra high-performance concrete

Jian-Xin Lu,Peiliang Shen,Yanjie Sun,Chi Sun Poon

DOI: https://doi.org/10.1016/j.cemconres.2022.106842

IF: 11.958

2022-08-01

Cement and Concrete Research

Abstract:The highly dense structure which causes the risk of explosive spalling is one of the major limitations of using ultra high-performance concrete (UHPC). This study developed a lightweight UHPC (L-UHPC) and proposed a strategy to improve its material efficiency and lower the risk of explosive spalling. High-strength hollow glass microspheres and fine lightweight aggregates were jointly used in the UHPC system to achieve light weight and ultra high strength. The L-UHPC was cured at different curing regimes to maximize its material efficiency and prevent its spalling after exposure to high temperature. The experimental results showed that the combination of lightweight materials and dry heat curing was effective in reducing the density ( 150 MPa) of the L-UHPC. By means of minimizing the amount of internal free water, the heat curing approach contributed to avoiding the thermal spalling of the L-UHPC exposed to fire conditions. Microstructural results indicated that the elevated temperature curing promoted the pozzolanic reaction and increased the microhardness of the paste matrix by increasing silicate polymerization of the C-S-H structure. The created voids of the collapsed glass microspheres might accommodate some internal vapor pressure and mitigate the degradation caused by the high temperature exposure. The synergetic effect of the porous materials and the dry heat curing lowered the thermal conductivity and significantly improved the material efficiency of the L-UHPC.

construction & building technology,materials science, multidisciplinary
A novel high-performance lightweight concrete prepared with glass-UHPC and lightweight microspheres: Towards energy conservation in buildings

Jian-Xin Lu,Hafiz Asad Ali,Yi Jiang,Xiwen Guan,Peiliang Shen,Peiyuan Chen,Chi Sun Poon

DOI: https://doi.org/10.1016/j.compositesb.2022.110295

2022-12-01

Abstract:Improving energy conservation of buildings and promoting wastes recycling contribute to reducing CO2 emissions. This work developed a green high-performance lightweight concrete (HPLC) with good thermal insulation for energy-saving purposes. The HPLC was comprised of lightweight microspheres and sustainable ultra high-performance concrete (UHPC), which was prepared with a large volume of waste glass. For the glass-based UHPC, the use of glass cullet led to mechanical decrement, while the workability and mechanical properties were improved with the replacement of 50% cement by glass powder. Combining glass aggregates and powder in UHPC significantly enhanced its thermal insulation properties. Meanwhile, incorporating two kinds of lightweight microspheres in the glass-based UHPC further lowered the density and thermal conductivity of HPLC. The performance of HPLC was dependent on the physical characteristics of lightweight microspheres rather than their chemical reaction based on molecular dynamics simulation. The developed HPLC exhibited a low density ( 100 MPa and flexural strength >35 MPa). The superior performance of HPLC was ascribed to the high pozzolanic reactivity of glass powder and its promotion on cement hydration, the low thermal conductivity of glass, the chemical reactivity of microspheres as well as their hollow nature for impeding heat transfer. The good flexure and thermal insulation performance would make this eco-HPLC a promising material for applications in energy efficient buildings and long-span lightweight structures.
Investigation of the Physical Mechanical Properties and Durability of Sustainable Ultra-High Performance Concrete with Recycled Waste Glass

Mohamed Amin,Ibrahim Saad Agwa,Nuha Mashaan,Shaker Mahmood,Mahmoud H. Abd-Elrahman

DOI: https://doi.org/10.3390/su15043085

IF: 3.9

2023-02-08

Sustainability

Abstract:Construction material sustainability and waste reuse have emerged as significant environmental issues. Concrete is widely used in the building and engineering fields. Ultra-high performance concrete (UHPC), which has remarkably high mechanical properties, has become one of the most common concrete varieties in recent years. As a result, substantial amounts of Portland cement (PC) are frequently used, raising the initial cost of UHPC and restricting its broad use in structural applications. A significant amount of CO2 is produced and a large amount of natural resources are consumed in its production. To make UHPC production more eco-friendly and economically viable, it is advised that the PC in concrete preparations be replaced with different additives and that the recycled aggregates from various sources be substituted for natural aggregates. This research aims to develop an environmentally friendly and cost-effective UHPC by using glass waste (GW) of various sizes as an alternative to PC with replacement ratios of 0%, 10%, 20%, 30%, 40%, and 50% utilizing glass powder (GP). Fine aggregate “sand (S)” is also replaced by glass particles (G) with replacement ratios of 0%, 50%, and 100%. To accomplish this, 18 mixes, separated into three groups, are made and examined experimentally. Slump flow, mechanical properties, water permeability, and microstructural characteristics are all studied. According to the results, increasing the S replacement ratio with G improved workability. Furthermore, the ideal replacement ratios for replacing PC with GP and S with G to achieve high mechanical properties were 20% and 0%, respectively. Increasing the replacement rate of GP in place of PC at a fixed ratio of G to S resulted in a significant decrease in water permeability values. Finally, a microstructural analysis confirms the experimental findings. In addition, PC100-S100 was the best mix compared to PC100-S50 G50 and PC100-G100.

environmental sciences,environmental studies,green & sustainable science & technology
Mechanical properties and microstructure of ultra-high strength concrete with lightweight aggregate

Lingqi Meng,Chunxiao Zhang,Jiuqi Wei,Lei Li,Jingbiao Liu,Shihe Wang,Yahong Ding

DOI: https://doi.org/10.1016/j.cscm.2022.e01745

IF: 4.934

2022-12-10

Case Studies in Construction Materials

Abstract:In recent years, the development of concrete has been toward to the direction of lightweight and high strengthening. This study developed a kind of lightweight ultra-high strength concrete(L-UHSC) through the comprehensive design method, which had an apparent density rang of 1995kg/m 3 -2114kg/m 3 and a compressive strength of 102.4 MPa-114.5 MPa. The specific strength of the designed L-UHSC is more than 50 MPa/(t/m 3 ), which is higher than ordinary structural lightweight aggregate concrete (LAC). Additionally, the roles of high-performance paste, lightweight aggregate (LWA) and steel fiber in L-UHSC were revealed through scanning electron microscopy (SEM), mercury intrusion porosimetry (MIP) and strength test. The findings revealed that SF content, rather than the binder-sand ratio and aggregate ratio, has a greater impact on density and strength, and the aggregate ratio having the least effect. As steel fiber content increases from 0.5% to 2.0%, compressive strength, flexural strength and splitting tensile strength of LAC increase by 44.3%, 120% and 151%, respectively, which is higher than that of ultra-high performance (UHPC). The micromorphology and pore structure research suggested that the high-performance paste plays a keystone role in achieving the ultra-high strength, and LWAs mainly affected strength through improving pore structure. In addition, small size pre-wetted LWA is more conducive to concrete strength. Our preliminary results provide a reference for the research and development of lightweight ultra-high strength cement composites.

construction & building technology,materials science, multidisciplinary,engineering, civil
The Durability of Ultra High Strength Fibre Reinforced Cementitious Material

Christian Paglia,S. Antonetti

DOI: https://doi.org/10.4028/p-v44g0n

2022-08-24

Key Engineering Materials

Abstract:Publication date: 24 August 2022 Source: Key Engineering Materials Vol. 929 Author(s): Christian Paglia, S. Antonetti The technology of concrete greatly evolved in the recent years. The use of cements with a high dosage and the addition of fibres allowed a very compacted cementitious matrix. This fact may greatly affect the durability of a cementitious system. In this work, the durability of an ultra high strength fibre reinforced concrete was studied. The microstructure was dense, compact and exhibited a low capillary and total porosity as well as water permeability. Fluid resin penetration tests under pressure also showed a local difference in the penetration depth: from a thin surface layer to local small regions. Thus, the penetration potential of salts and water transporting degrading substances from the surface was reduced. The cement-based material was exposed to accelerated freeze/thaw and sulphate penetration tests, to clarify the durability and the capability of the low porous matrix to withstand the ingress of substances. In both cases the resistance was significantly higher as compared to conventional concrete. The crystalline quartz-rich matrix and the chemistry also played a relevant role in the low degradation of the system.

English Else
Composition Design and Fundamental Properties of Ultra-High-Performance Concrete Based on a Modified Fuller Distribution Model

Xiaogeng Xie,Junqi Fan,Peng Guo,Haoliang Huang,Jie Hu,Jiangxiong Wei

DOI: https://doi.org/10.3390/ma16020700

IF: 3.4

2023-01-12

Materials

Abstract:Both the discrete and continuous particle packing models are used to design UHPC, but the influences of a water film covering the particle surfaces on the compactness of the particle system were not considered in previous research. In fact, the water film results in a certain distance between solid particles (DSP), which affects the compactness of the particle system, especially for cementitious materials with small particle sizes. In the present study, the mixture design method for UHPC was proposed based on the Fuller distribution model modified using the DSP. Then, the components of cementitious materials and aggregates were optimized, and the UHPC matrices with high solid concentrations were obtained. The results showed that the solid concentration, slump flow, and compressive strength of the UHPC matrix reached 77.1 vol.%, 810 mm, and 162.0 MPa, respectively. By replacing granulated blast furnace slag (GBFS) with quartz powder (QP), the flexural strength of the UHPC matrix was increased without reducing its compressive strength. When the steel fiber with a volume fraction of 1.5% was used, the slump flow, compressive strength, tensile strength, and flexural strength of the UHPC reached 740 mm, 175.6 MPa, 9.7 MPa, and 22.8 MPa, respectively. After 500 freeze–thaw cycles or 60 dry–wet cycles under sulfate erosion, the mechanical properties did not deteriorate. The chloride diffusion coefficients in UHPCs were lower than 3.0 × 10−14 m2/s, and the carbonation depth of each UHPC was 0 mm after carbonization for 28 days. The UHPCs presented ideal workability, mechanical properties, and durability, demonstrating the validity of the method proposed for UHPC design.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Effect of air entraining and pumice on properties of ultra-high performance lightweight concrete

Abdullah M. Zeyad,Mohamed Amin,Ibrahim Saad Agwa

DOI: https://doi.org/10.1007/s43452-023-00823-3

IF: 4.042

2023-12-02

Archives of Civil and Mechanical Engineering

Abstract:This study focuses on developing the production of ultra-high-performance lightweight concrete (UHPLC) by combining pumice with an air-entraining agent. Air-entraining agents of aluminum powder (AP) and lightcrete (LC) were added in amounts of 0.1, 0.2, 0.3, 0.4, and 0.5% by weight of cement to create air bubbles. Crushed pumice has also been used as a partial sand replacement in proportions of 25% and 50% by volume, with or without the addition of AP or LC. To investigate the fresh, mechanical, and microstructural properties, seventeen UHPLC combinations were constructed. A slump flow diameter test was conducted to evaluate the characteristics of fresh UHPLC, and mechanical properties were evaluated by completing dry density, compressive strength, tensile strength, flexural strength, modulus of elasticity, and dry shrinkage tests. The effect of high temperatures of 20, 400, 600, and 800 °C on compressive strength was also investigated. The microstructure characteristics were analyzed using a scanning electron microscope. The research concluded that high-performance concrete with a compressive strength of 127.6 MPa and a dry density of 1970 kg/m 3 could be produced after a 28-day age test. This was accomplished by including 0.1% LC by weight of cement and 25% pumice as a partial substitute for sand. The mixture with 50% pumice as a partial replacement for sand and the addition of 0.5% LC of the cement weight exhibited the least loss in compressive strength when subjected to high temperatures.

engineering, mechanical,materials science, multidisciplinary, civil
Towards Ultrahigh Performance Concrete Produced with Aluminum Oxide Nanofibers and Reduced Quantities of Silica Fume

Scott Muzenski,Ismael Flores-Vivian,Behrouz Farahi,Konstantin Sobolev

DOI: https://doi.org/10.3390/nano10112291

2020-11-19

Abstract:Ultrahigh performance concrete (UHPC), which is characterized by dense microstructure and strain hardening behavior, provides exceptional durability and a new level of structural response to modern structures. However, the design of the UHPC matrix often requires the use of high quantities of supplementary cementitious materials, such as silica fume, which can significantly increase the cost and elevate the production expenses associated with silica fume handling. This paper demonstrates that a fiber-reinforced composite with properties similar to conventional UHPC can be realized with very low quantities of silica fume, such as 1% by mass of cementitious materials. The proposed UHPC is based on reference Type I cement or Type V Portland cement with very low C3A (<1%) that also complies with Class H oil well cement specification, silica fume, small quantities of Al2O3 nanofibers, and high-density polyethylene or polyvinyl alcohol macro fibers. Previous research has demonstrated that nanofibers act as a seeding agent to promote the formation of compact and nanoreinforced calcium silicate hydrate (C-S-H) clusters within the interparticle and nanofiber spaces, providing a nanoreinforcing effect. This approach produces a denser and stronger matrix. This research expands upon this principle by adding synthetic fibers to ultrahigh strength cement-based composites to form a material with properties approaching that of UHPC. It is indicated that the developed material provides improved strain hardening and compressive strength at the level of 160 MPa.
ANOVA-guided assessment of waste glass and limestone powder influence on ultra-high-performance concrete properties

Joaquin Abellan-Garcia,Yassir M. Abbas,Mohammad Iqbal Khan,Francisco Pellicer-Martínez

DOI: https://doi.org/10.1016/j.cscm.2024.e03231

IF: 4.934

2024-05-05

Case Studies in Construction Materials

Abstract:Ultra-high-performance concrete (UHPC) possesses remarkable structural and durability characteristics, yet its widespread acceptance is hindered by cost inefficiency and environmental concerns. To address these challenges, this study investigates the impact of waste glass and limestone powder as partial substitutes for silica fume and cement in UHPC. For this, three distinct formulations are studied (Control, Optimized-1, and Optimized-2), representing different dosages of waste glass and limestone powder. The research focuses on six critical properties (compressive strength, modulus of elasticity, ultrasonic pulse velocity, initial surface absorption, density absorption, voids, and chloride ion penetration) evaluated at different ages (1, 7, 28, and 90 days for compressive strength, and 7, 28, and 90 days for the remaining properties). So, a total of 171 test specimens were examined, with 3 samples for each age and formulation. Statistical analysis, using ANOVA, assessed and confirmed the significance of the factors in the experimental results. The findings provide comprehensive insights into the UHPC formulations, highlighting the influence of waste glass and limestone powder on specified properties over varying ages. The research reveals that, despite the optimized blends exhibiting lower compressive strength values, all mixes surpass the 150 MPa threshold for cylindrical samples at the 90-day mark. Moreover, the Control mix consistently outperforms the optimized blends in modulus of elasticity at all ages, meeting ACI 239 criteria. The void content analysis shows encouraging trends, with all formulations displaying voids of less than 5% on the seventh day, improving during the curing process. Notably, Optimized-2 demonstrates superior performance over the Control mix after 90 days. Chloride ion penetration is minimal for all blends after 90 days, confirming the effectiveness of mineral admixtures. ANOVA analysis confirms significant impacts of formulation and age on various UHPC characteristics, emphasizing the consistent reduction in performance with alternative mineral additions. The interaction between formulation and age implies variations in property evolution, suggesting potential convergence with alternative formulations.

construction & building technology,materials science, multidisciplinary,engineering, civil
Ultra-High-Performance Concrete (UHPC) - Applications Worldwide: A State-of-the-Art Review

DOI: https://doi.org/10.33976/jert.10.1/2023/2

2023-03-01

Journal of Engineering Research and Technology

Abstract:Research is in progress on the applications of ultra-high performance concrete (UHPC) as a new additive material in construction technology. Over the last twenty years’ significant improvements have been achieved in mechanical properties of UHPC, such as its strength, workability, and ductility, with further improvements made in self-placing properties, higher density, and durability compared with normal concrete. One of the biggest advantages offered by ultra-high performance concrete over normal concrete is the possibility to minimize the cross-sectional dimensions of the structural elements. UHPC can be used to provide significant long-span members, whilst also showing less variation, creep, and drying shrinkage compared to conventional concrete. After many years of development and research into UHPC’s properties, it is being used in commercial applications to meet the rising demand for quality constructions. Many projects in the world started using UHPC for different construction objectives such as long spans, columns, jacketing, rain-screen cladding systems, panel systems, façades, etc. Furthermore, there are not enough sources in the literature describing mixture design, preparation, and curing. This research gives an overview of the uses of UHPC in structural and architectural applications.
A novel development of ultra-high-performance concrete with calcium oxide-activated materials and fibers: engineering properties and sustainability evaluation

Hadi Bahmani,Davood Mostofinejad

DOI: https://doi.org/10.1680/jmacr.23.00234

IF: 2.46

2024-02-25

Magazine of Concrete Research

Abstract:This study developed a novel ultra-high-performance concrete using calcium oxide-activated materials (UHPC-CAM) and modified synthetic macro and glass fibers. The mechanical and durability properties of the UHPC-CAM samples with different fiber types were tested and compared. The microstructure of the samples was examined by scanning electron microscopy (SEM). The environmental impacts of the mix designs were assessed by the IMPACT 2002+ method, a life cycle assessment (LCA) tool. The results showed that the UHPC-CAM had a high compressive strength of over 110 MPa and improved ductility when glass and synthetic macro fibers were used. The samples also had low water absorption and high electrical resistance, indicating low corrosion risk. The SEM analyses showed that the synthetic macro fibers created a denser geopolymer matrix than the glass fibers. The UHPC-CAM had lower environmental impacts than conventional UHPC in terms of human health, ecosystem quality, carbon footprint, and resources. Synthetic macro fibers were the most eco-friendly fibers for UHPC-CAM production.

construction & building technology,materials science, multidisciplinary
Mechanical and Microstructural Properties of Ultra-High Performance Concrete with Lightweight Aggregates

Hani Alanazi,Oussama Elalaoui,Musa Adamu,Saleh O. Alaswad,Yasser E. Ibrahim,Aref A. Abadel,Abdulrahman Fahad Al Fuhaid

DOI: https://doi.org/10.3390/buildings12111783

IF: 3.324

2022-10-25

Buildings

Abstract:Although ultra-high-performance concrete (UHPC) presents superior mechanical properties and durability compared to conventional concrete; its spalling resistance to elevated temperatures is much lower compared to conventional concrete due to the high compactness and absence of capillary pores. This paper investigated the influence of lightweight aggregate (LWA) on the strength properties and microstructure of UHPC to enhance its resistance to elevated temperatures. UHPC specimens prepared with LWA as a partial replacement of silica sand were produced. The study evaluated the compressive and flexural strengths, failure mode, mass loss, and microstructure of the specimens, using SEM. The results showed that the compressive strength of the UHPC specimen was reduced with increasing the content of LWA at ambient temperature, but the compressive strength of the UHPC specimens prepared with LWA improved when exposed to elevated temperatures. The replacement of 10% of the silica sand with LWA led to an increase in the compressive strength from 100 MPa to 110 MPa after exposure to 200 °C; however, the flexural strength decreased from 23.6 MPa to 18.3 MPa. On the contrary, the flexural strength of UHPC increased with the inclusion of LWA at an ambient temperature but reduced with high-temperature exposure. The failure mode of UHPC was not significantly affected by the variation in LWA content and temperature. In addition, the SEM result confirms that LWA is an effective internal curing material for enhancing the microstructure and compressive strength of UHPC

construction & building technology,engineering, civil
A Comprehensive Study on Non-Proprietary Ultra-High-Performance Concrete Containing Supplementary Cementitious Materials

Seyedsaleh Mousavinezhad,Srinivas Allena,Gregory J. Gonzales,William K. Toledo,Judit M. Garcia,Craig M. Newtson

DOI: https://doi.org/10.3390/ma16072622

IF: 3.4

2023-03-26

Materials

Abstract:Ultra-high performance concrete (UHPC) is a novel cement-based material with exceptional mechanical and durability properties. Silica fume, the primary supplementary cementitious material (SCM) in UHPC, is expensive in North America, so it is often substituted with inexpensive class F fly ash. However, future availability of fly ash is uncertain as the energy industry moves toward renewable energy, which creates an urgent need to find cost-effective and environmentally friendly alternatives to fly ash. This study investigated replacing cement, fly ash, and silica fume in UHPC mixtures with ground granulated blast-furnace slag (GGBFS), metakaolin, and a natural pozzolan (pumicite). To identify acceptable UHPC mixtures (28-day compressive strength greater than 120 MPa), workability, compression, and flexural tests were conducted on all mixtures. Then, durability properties including shrinkage, frost resistance, and chloride ion permeability (rapid chloride permeability and surface resistivity tests) were evaluated for the acceptable UHPC mixtures. Results showed that 75, 100, and 40% of fly ash in the control mixture could be replaced with pumicite, metakaolin, and GGBFS, respectively, while still producing acceptable strengths. Flexural strengths were greater than 14.20 MPa for all mixtures. For durability, UHPC mixtures had shrinkage strains no greater than 406 μstrain, durability factors of at least 105, and "very low" susceptibility to chloride ion penetration, indicating that these SCMs are suitable candidates to completely replace fly ash and partially replace silica fume in non-proprietary UHPC.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering

Checking out the G(2)/M transition.

Characteristics of ultra-high performance lightweight concrete containing hollow glass microspheres under severe loading conditions

Lightweight ultra-high-performance concrete (UHPC) with expanded glass aggregate: Development, characterization, and life-cycle assessment

Physical, Mechanical, and Microstructure Characteristics of Ultra-High-Performance Concrete Containing Lightweight Aggregates

Compressive Strength and Chloride Resistance of Slag/Metakaolin-Based Ultra-High-Performance Geopolymer Concrete.

Assessing durability properties of ultra-high performance concrete-class materials

Preparation and properties of ultra-high performance lightweight concrete

Fracture behavior of ultra‐high performance lightweight concrete: In situ investigations using μ‐CT

Strategy for preventing explosive spalling and enhancing material efficiency of lightweight ultra high-performance concrete

A novel high-performance lightweight concrete prepared with glass-UHPC and lightweight microspheres: Towards energy conservation in buildings

Investigation of the Physical Mechanical Properties and Durability of Sustainable Ultra-High Performance Concrete with Recycled Waste Glass

Mechanical properties and microstructure of ultra-high strength concrete with lightweight aggregate

The Durability of Ultra High Strength Fibre Reinforced Cementitious Material

Composition Design and Fundamental Properties of Ultra-High-Performance Concrete Based on a Modified Fuller Distribution Model

Effect of air entraining and pumice on properties of ultra-high performance lightweight concrete

Towards Ultrahigh Performance Concrete Produced with Aluminum Oxide Nanofibers and Reduced Quantities of Silica Fume

ANOVA-guided assessment of waste glass and limestone powder influence on ultra-high-performance concrete properties

Ultra-High-Performance Concrete (UHPC) - Applications Worldwide: A State-of-the-Art Review

A novel development of ultra-high-performance concrete with calcium oxide-activated materials and fibers: engineering properties and sustainability evaluation

Mechanical and Microstructural Properties of Ultra-High Performance Concrete with Lightweight Aggregates

A Comprehensive Study on Non-Proprietary Ultra-High-Performance Concrete Containing Supplementary Cementitious Materials