Abstract:Current spinal testing protocols generally adopt pure moments combined with axial compression. However, daily activities involve multi-axis loads, and multi-axis loading has been shown to impact intervertebral disc (IVD) cell viability. Therefore, integrating in-vivo load data with spine simulators is critical to understand how loading affects the IVD, but doing so is challenging due to load coupling and variable load rates. This study addresses these challenges through the Load Informed Kinematic Evaluation (LIKE) protocol, which was evaluated using the root mean squared error (RMSE) between desired and actual loads in each axis. Stage 1 involves obtaining the kinematics from six-axis load control tests replicating 20 Orthoload activities at a reduced test speed. Stage 2 applies these kinematics in five axes, with axial compression applied in load control, at the reduced speed and at the physiological test rate. Stage 3 enables long-term tests through six-axis kinematic control combined with diurnal height correction to account for the natural height fluctuations of the IVD. Stage 1 yielded RMSEs within twice the load cell noise floor. Low RMSEs were maintained during stage 2 at reduced speed (Tx:0.80 ± 0.30 N; Ty:0.77 ± 0.29 N; Tz:1.79 ± 0.50 N; Rx:0.02 ± 0.01Nm; Ry:0.02 ± 0.01Nm; and Rz:0.02 ± 0.01Nm) and at the physiological test rate (Tx:3.45 ± 1.81 N; Ty:3.82 ± 1.99 N; Tz:11.32 ± 8.69 N; Rx:0.13 ± 0.07Nm; Ry:0.16 ± 0.11Nm; and Rz:0.07 ± 0.04Nm). To address unwanted oscillations observed in longer tests (>2h), Stage 3 was introduced to enable the stable and consistent replication of activities at a physiological test rate. Despite higher RMSEs the axial error was 85.5 ± 24.27 N (equivalent to ∼ 0.16 MPa), with shear RMSEs similar to other testing systems conducting pure moment tests at slower rates. The LIKE protocol enables the replication of physiological loads, providing opportunities for enhanced investigations of IVD mechanobiology, and the pre-clinical evaluation of IVD devices and therapies.

A novel posture control device to induce high-rate complex loads for spine biomechanical studies

Off-Axis Loading Fixture for Spine Biomechanics: Combined Compression and Bending

New methodology for multi-dimensional spinal joint testing with a parallel robot

Design and Optimization of a Wearable Underactuated Mechanism for Spinal Posture Measurement

Design and Computational Modeling of a Modular, Compliant Robotic Assembly for Human Lumbar Unit and Spinal Cord Assistance

Multibody dynamics and optimal control for optimizing spinal exoskeleton design and support

Design, Evaluation, and Implementation of a Novel Magnetic Resonance Imaging-Compatible Physiologic Loading Simulator for Ex-Vivo Joints

Concept Design of a Novel Robotic Spinal Brace for the Treatment of Scoliosis

Spine-Inspired Continuum Soft Exoskeleton for Stoop Lifting Assistance

Biomechanical Study of Lumbar Spine (L2-L4) Using Hybrid Stabilization Device - A Finite Element Analysis

Modal Decoupled Dynamics Feed-Forward Active Force Control Of Spatial Multi-Dof Parallel Robotic Manipulator

Design Improvements and Validation of a Novel Fully 3D Printed Analogue Lumbar Spine Motion Segment

Load-Sharing and Kinematics of the Human Cervical Spine Under Multi-Axial Transverse Shear Loading: Combined Experimental and Computational Investigation

A New Method to Evaluate Pressure Distribution Using a 3D-Printed C2-C3 Cervical Spine Model with an Embedded Sensor Array

Modal Decoupled Dynamics-Velocity Feed-Forward Motion Control of Multi-DOF Robotic Spine Brace.

Load Changes on a Short-Segment Posterior Instrumentation After Transosseous Disruption of L3 Vertebra – A Biomechanical Human Cadaveric Study

Design and implementation of a novel modal space active force control concept for spatial multi-DOF parallel robotic manipulators actuated by electrical actuators

Kinematic And Kinetic Analysis Of 3-Rpr Based Robotic Lumbar Brace

A Novel Reconfigurable Gravity Balancer for Lower-Limb Rehabilitation With Switchable Hip/Knee-Only Exercise

The physiological, in-vitro simulation of daily activities in the intervertebral disc using a load Informed kinematic evaluation (LIKE) protocol

Development of Contact Medical Devices via Integrated Testing, Skeletal Muscle Modeling, and Finite Element Analysis