[Neurologic and encephalographic syndrome of hyperbarism].

R. Brauer,S. Dimov,X. Fructus,P. Fructus,A. Gosset,R. Naquet

1969-09-01

Abstract:

What problem does this paper attempt to address?

Preparation and Characterization of Sulfated Carboxymethyl Cellulose Nanofiltration Membranes with Improved Water Permeability

Ling-Ling Shao,Quan-Fu An,Yan-Li Ji,Qiang Zhao,Xue-San Wang,Bao-Ku Zhu,Cong-Jie Gao

DOI: https://doi.org/10.1016/j.desal.2014.01.025

IF: 11.211

2014-01-01

Desalination

Abstract:Sulfated carboxymethyl cellulose (SCMC) with tailored amount of sulfate groups was synthesized, and their composite nanofiltration membranes (SNFMs) were prepared by solution casting onto polysulfone (PSF) supporting membrane and crosslinking by glutaradehyde (GA). Chemical structure and composition of SCMCs and SNFMs were characterized by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. SNFM surfaces were examined by field emission scanning electron microscopy, water contact angle and streaming potential measurement. The effects of the chemical composition on the hydrophilicity, the surface charge and the nanofiltration performance of SNFMs were determined. It is found that the incorporation of sulfate groups improves the water permeability of SNFMs while retaining their salt rejection. For the feed mixture of aqueous Na2SO4 (1.0gL−1, pH=6.5), the optimum water flux is 39.6Lm−2h−1, which is 2.2 times of the pristine SNFM-0. For the xylenol orange (XO) dye solution (0.1gL−1, pH=4.0), the flux of SNFM-3 (30.0Lm−2h−1) is also higher than that of SNFM-0 (11.1Lm−2h−1). In addition, SNFM-3 exhibits good separation performance and chemical stability in treating saline anionic dye aqueous solution (MYB/NaCl) in acidic conditions.
Multiporous Microstructure for Enhancing the Water Absorption and Swelling Rate in Poly(sodium Acrylic Acid) Superabsorbent Hydrogels Based on a Novel Physical and Chemical Composite Foaming System

Si Chen,Bo Zhou,Meng Ma,Bozhen Wu,Yanqin Shi,Xu Wang

DOI: https://doi.org/10.1002/app.44149

IF: 3

2016-01-01

Journal of Applied Polymer Science

Abstract:ABSTRACTIn this article, we report a novel physical and chemical composite foaming system, which was used to successfully prepare high‐performance and low‐cost composite superabsorbent [poly(sodium acrylic acid) (PAA–Na)] hydrogels based on acrylic acid by free‐radical polymerization in a water bath under a nitrogen atmosphere without the use of any organic solvents. The prepared hydrogels showed superabsorbent properties, high water‐absorption abilities and swelling rates, a lighter packing density, and a multiporous microstructure. Fourier transform infrared spectroscopy and scanning electron microscopy revealed that the sodium dodecyl sulfate surfactant, sodium bicarbonate chemical foaming agent, and 1,1,2‐trifluorotrichloroethane physical foaming agent were evenly distributed and grafted onto the PAA–Na matrix. Water‐absorption, swelling rate, and packing density testing confirmed that the superabsorbent had a high water‐absorption ability and swelling rate and a lighter packing density. Furthermore, we investigated the effects of different foaming agents, including chemical and physical foaming agents, on the swelling and water‐retention capabilities of the superabsorbent hydrogels (SAHs).The results show that the combination of these foaming agents significantly improved the water‐absorbing capacity. With the help of these foaming agents, we obtained PAA–Na hydrogels without any organic solvents for posttreatment or special porogens; this is an environmentally beneficial way to prepare SAHs for hygiene and biomedical products. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016, 133, 44149.
Enhancing the efficacy of feminine hygiene sanitary napkins by developing a super absorbent polymer based on methyl methacrylate and methacrylic acid

Chintan Madhu,Bharat Patel

DOI: https://doi.org/10.1002/app.56038

IF: 3

2024-07-26

Journal of Applied Polymer Science

Abstract:Application of SAP on sanitary napkins and its performance analysis. Super absorbent polymer based on methyl methacrylate (MMA), methacrylic acid (MAA) has been prepared during the present work for coating the top layer of feminine sanitary napkins. Synthesized polymers were coated on the needly punched cotton and adjusted as the top layer of the sanitary napkins, which has been prepared. The samples were evaluated by means of absorbency capacity, rewet back, strike through, and pH by the comparative study with commercially available sanitary napkin. The most suitable ratio of monomers (60 g MMA, and 40 g MAA) for synthesizing polymer was suggested. Absorbency capacity of the said ratio is competing with commercial sample with 63.68 g absorbent capacity. Specially, pH of prepared polymers suggested the acidic value and those are more preferable for maintaining the acidic pH of vagina at the menstrual time. Present work suggests the polymer, which can be utilize for coating the feminine napkin by the comparative result suggested by absorbency capacity, rewet back, strike through, and pH.

polymer science
Formulation and characterization of super absorbent copolymer AA, ACN-grafted sodium acrylate for feminine napkin

Chintan Madhu,Bharat Patel

DOI: https://doi.org/10.1080/00405000.2024.2406608

IF: 1.7698

2024-09-25

Journal of the Textile Institute

Abstract:Absorbency for feminine napkins is a research priority in the recent era, though commercial napkins are available with the same function properties achieved through finishing. One of those methods is coating SAPs, which act as hydrogels. Super absorbent polymers are generally coated in the second- or third-layer of the napkin. The present work deals with the coating of the SAP on the top layer by forming poly (acrylic acid)/sodium acrylate (ACN-g-PAA/SA) and demonstrating its absorption properties. Ultimately, we conducted a comparative analysis of all the SAPs prepared, and demonstrated an absorptive capacity of 104.35 g/g in tap water and 51.28 g/g in saline solution during free swelling. Additionally, under a specific load, it demonstrated 56.48 g/g in tap water and 27.42 g/g in saline solution. Based on the comparative results suggested by the TGA curve, water absorbency, and moisture content, the present work proposes a polymer suitable for coating the feminine napkin.

materials science, textiles
Novel Degradable Superabsorbent Polymers Based on Carboxymethyl Cellulose

Gyu Dong Lee,Song Jun Doh,Yoonjin Kim,Jung Nam Im

DOI: https://doi.org/10.1007/s12221-024-00740-z

IF: 2.5

2024-10-29

Fibers and Polymers

Abstract:In this study, biocompatible and biodegradable superabsorbent polymers (SAPs) were prepared from carboxymethyl cellulose (CMC) using citric acid as a crosslinking agent, utilizing a high-concentration CMC paste and a short annealing process. The effects of CMC molecular weight, annealing temperature and time, and crosslinker concentration on the absorption properties in saline solution were evaluated. In addition, the effects of mixing CMC SAPs with different molecular weights were explored to optimize performance. The results showed that CMC molecular weight significantly affected absorption properties, with medium molecular weight (395 kDa) exhibiting the best overall performance. The content of the crosslinking agent and annealing conditions were also critical—higher crosslinking improved absorption under load but reduced free swell absorption and retention. In addition, the absorption properties could be optimized by appropriately mixing the CMC SAPs with different molecular weights, indicating complementary interactions that enhance performance beyond the individual contributions of each SAPs. These findings can contribute to the development of environmentally friendly, high-performance superabsorbent materials for personal care products as a sustainable alternative to conventional petroleum-derived SAPs.

materials science, textiles,polymer science
Development of biopolymer-based menstrual pad and quality analysis against commercial merchandise

Md. Moynul Hassan Shibly,Mohammad Anower Hossain,M. Forhad Hossain,Md Golam Nur,Mohammad Billal Hossain

DOI: https://doi.org/10.1186/s42269-021-00504-2

2021-03-04

Bulletin of the National Research Centre

Abstract:Abstract Background Managing menstrual hygiene in the least developed countries represents a significant obstacle for women and girls. Commonly dirty stuffs are used to control the menstrual cycle which causes many diseases, while disposable hygiene-absorbent material during menstruation is an essential requirement. Most local commercial sanitary napkins offer high absorptiveness and flexibility; however, most of them, due to the use of synthetic superabsorbent polymer (SAP) within the core layer, are not biodegradable and harmful to human skin. This research aims to create a sanitized and biodegradable pad in order to replace SAP with environmentally sound biopolymer that give rural poor women competent performance and characteristics. Result For the construction of the model, some of the current sanitary pads from the local market are examined. Six models are designed using various biopolymers such as cotton, viscose, wood pulp, sodium alginate and carboxy methyl cellulose (CMC) in different proportions as the core absorbent layer to boost requirements such as absorption, fluid retention strength, coziness and cost reduction. The sanitized pads have gone through various investigations such as antimicrobial activity, wicking ability and water retention capacity to standardize vital features and value. The experimental results show the use of sodium alginate and CMC is a possible replacement for SAP as the best comparable result is observed in template consuming sodium alginate, CMC and cellulosic fibre. Non-woven fabric treated with neem extract forming the outer layer of sanitary napkin serving with antimicrobial activity of more than 90% against both gram-positive and gram-negative bacteria. Conclusion Outcomes recommend significant advancement and cost-effectiveness of the newly designed archetype. Sanitary napkins without SAP can be a safe disposal solution and can therefore have a sustainable environmental impact.

English Else
Synthesis and Characterization of Silk Sericin/Acrylic Acid/Acrylamide Superabsorbent Polymer

Lian-Xia Deng,Hai-Ping Zhang,Liang-Jun Zhu,Min-Ying Yang,Si-Jia Min,Rong Lin,Xue-Yun Wang

DOI: https://doi.org/10.3993/jfbi12201102

2011-01-01

Abstract:A composite superabsorbent material was synthesized based on silk sericin, acrylic acid and acrylamide by using N,N-methylenebisacrylamide (MBA) as the crosslinker and ammonium persulfate (APS) as the initiator reagent. The water absorbency and water retaining properties of the composite under different preparation conditions were investigated. The absorbency of silk sericin /acrylic acid /acrylamide (SS/AA/AM) superabsorbent polymer polymer in deionized water, tap water and 0.9% NaCl solution were 285 similar to 337 g/g, 191 similar to 220 g/g, 36 similar to 43g/g, respectively. SS/AA/AM: material has excellent re-absorbent abilities and can be reused. The product showed different water absorbency in aqueous chloride salt solutions with the order of Na+ > Ca2+ > Mg2+ > Al3+. FTIR spectra results indicated that silk sericin was successfully grafted with acrylic acid and acrylamide molecules. The study on the absorbent material based on sericin is useful for further research on biodegradable superabsorbent polymer.
Development of essential oil-containing antimicrobial and deodorizing nanofibrous membranes for sanitary napkin applications

Hanul Lee,Seungsin Lee

DOI: https://doi.org/10.1177/15280837241248838

2024-05-01

Journal of Industrial Textiles

Abstract:Journal of Industrial Textiles, Volume 54, Issue , January-December 2024. In this study, antimicrobial and deodorizing nanofibrous composite membranes based on natural substances were developed for use in feminine sanitary napkins. Plant-derived natural essential oils, such as lemongrass oil and May Chang oil, were incorporated into polyvinyl alcohol nanofibers using emulsion electrospinning. The fiber morphology, oil distribution, and pore size distribution of the nanofibrous composite membranes were examined. The antimicrobial and deodorizing effects, tensile properties, and release behavior of the functional ingredients from the composite membranes were investigated to examine their use in sanitary napkins. Core–sheath nanofibers, in which lemongrass oil or May Chang oil was uniformly distributed within the fiber core, were fabricated using various oil contents. The essential oil-loaded nanofibrous composite membranes contained pores ranging from 0.130 to 1.349 μm in size. The release profiles of the essential oils from the composite membranes over an 8 h period demonstrated a continuous release of citral and limonene. Composite membranes containing either lemongrass oil or May Chang oil exhibited outstanding antimicrobial effects against vaginal pathogens, such as Candida albicans and Staphylococcus aureus, despite their low oil content. Deodorizing effects against ammonia gas were observed at oil contents higher than that required to achieve antimicrobial effects. The composite membranes exhibited lower Young's modulus and greater elongation at break values under wet conditions compared to dry conditions. Our findings demonstrate that antimicrobial and deodorizing nanofibrous composite membranes based on plant-derived essential oils have the potential for use in feminine hygiene products.

materials science, textiles
Biocompatible Cellulose-Based Superabsorbents for Personal Care Products

Rafael C. Rebelo,Blanca Vélez Báguena,Patrícia Pereira,Rui Moreira,Jorge F. J. Coelho,Arménio C. Serra

DOI: https://doi.org/10.1007/s10924-024-03315-4

IF: 4.705

2024-05-19

Journal of Polymers and the Environment

Abstract:Personal care products are an inseparable part of urban society, but the widespread use of petroleum-based superabsorbent polymers (SAPs) poses significant environmental negative impact. To overcome this problem, we investigated the development of cellulose-based hydrogels through di-epoxide chemical crosslinking of cellulose/cellulose electrolytes in NaOH/Urea aqueous system. The aim was to exploit mechanical strength, hydrophilicity, non-toxicity, and biodegradability of cellulose as the absorbent core of personal hygiene products through a simple synthesis method. The synthesized cellulose materials significantly improved the absorption capacity of the gels by 220%, reaching up to 41 g/g. The absorption properties were influenced by the cellulose DS, crosslinking density, and fluid salinity. The hydrogels demonstrated a remarkable absorption capacity of synthetic urine (27 g/g) and underload conditions (12 g/g). Their non-cytotoxic and biodegradable nature showed their potential for the manufacturing of personal care products such as disposable diapers or daily pads.

engineering, environmental,polymer science
Synthesis and Properties of Acrylic-Based Superabsorbents with Enhanced Crosslinking on Particle Surface

J Huang,ZM Huang,YZ Bao,ZX Weng

DOI: https://doi.org/10.1142/s0256767905000655

2005-01-01

Abstract:A series of acrylic-based superabsorbent resins were synthesized by inverse suspension polymerization, using potassium persulfate as the initiator, N, N'-methylene bisacrylamide (BIS) and divinylbenzene (DVB) as the multiple crosslinking agents. The morphology of the resulting superabsorbent resins revealed by SEM demonstrated that a hard shell layer was indeed formed due to surface crosslinking. The swelling and deswelling properties, and the mechanical strength of superabsorbents were investigated. The results indicated that the adding time of DVB and the amount of DVB participated in the crosslinking show a significant influence on the properties of superabsorbents. When DVB was added in polymerization later, the amount of DVB participated in reaction decreases and the surface crosslinked shell becomes thinner. It is suitable for DVB to be introduced in the later stage of the polymerization process, because the absorption rate of resin is efficiently improved in conjunction with higher water absorption. Furthermore, it was found that the mechanical strength of swollen superabsorbent with surface crosslinking was indeed enhanced in comparison with that of the conventional one.
Dynamic Doppler Frequency Shift Errors: Measurement, Characterization, and Compensation

Chen Wang,J. Ellis

DOI: https://doi.org/10.1109/TIM.2014.2377991

IF: 5.6

2015-01-13

IEEE Transactions on Instrumentation and Measurement

Abstract:Positioning calibration under dynamic conditions is becoming increasingly of interest for high precision fields, such as additive manufacturing and semiconductor lithography. Heterodyne interferometry is often used to calibrate a stage's position because interferometry has a high dynamic range and direct traceability to the meter. When using heterodyne interferometry, filtering is routinely performed to process and determine the measured phase change, which is proportional to the displacement from one target location to another. The filtering in the signal processing introduces a phase delay dependent on the detection frequency, which leads to displacement errors when target velocity is non-constant as is the case in dynamic calibrations. This paper presents a phase delay compensation method by measuring instantaneous detection frequency and solving for the corresponding phase delay in a field-programmable gate array (FPGA) in real time. The FPGA hardware-in-the-loop simulation shows that this method can significantly decrease the displacement error from ±100's nm to ±3 nm in dynamic cases and it will still keep subnanometer resolution for quasi-static calibrations.
Synthesis and characterization of reinforced acrylic-based superabsorbents crosslinked with divinylbenzene

Jian Huang,Zhi-Ming Huang,Yong-Zhong Bao,Zhi-Xue Weng

DOI: https://doi.org/10.1002/app.23604

IF: 3

2006-01-01

Journal of Applied Polymer Science

Abstract:A series of superabsorbent polymers were synthesized by an inverse suspension polymerization, with potassium persulfate as the initiator, Span60 as the dispersant, and N,N'-methylene bisacrylamide (BIS) and divinylbenzene (DVB) as multiple crosslinkers. The synthesis conditions, including the amount of dispersant, concentration of crosslinkers, oil-to-water phase ratio (O/W) of the polymerization system, total monomer concentration, and acrylamide (AM) content were studied. The results indicated that there were optima for the following properties: BIS crosslinker concentration (0.075 wt %), O/W (3:1), total monomer concentration (37.5 wt %), and AM content (5 wt %). In addition, the particle size had a significant influence on the absorption speed, and the absorption speed increased with decreasing particle size. In comparison with the conventional sample crosslinked only by BIS, the superabsorbent with the same particle size but crosslinked by multiple crosslinkers had the higher absorption rate because of surface crosslinking. It also showed that the salt resistance and antihydrolyzing property of the superabsorbent crosslinked by multiple crosslinkers (BIS and DVB) were enhanced, which was also attributed to surface crosslinking by DVB. (c) 2006 Wiley Periodicals, Inc.
Asymmetric wetting and antibacterial composite membrane obtained by spraying bacterial cellulose grafted with chitosan for sanitary products surface layers

Yang Wang,Xu Liu,Rendang Yang,Qianli Ma

DOI: https://doi.org/10.1016/j.carbpol.2020.117602

IF: 10.723

2021-03-01

Carbohydrate Polymers

Abstract:The asymmetric wetting membranes have attracted intense attention in liquid directional transportation. However, it is a huge challenge to prepare surface layer membrane for sanitary products with antibacterial and asymmetric wettability by a simple method. Herein, the bacterial cellulose grafted with chitosan (BC-CS) was used as the hydrophilic agent to modify polypropylene nonwoven fabric (PPF) substrate via easy and effective one-sided layer-by-layer spraying to prepare the asymmetric wetting and antibacterial composite membrane (BC-CS/PPF). It showed that the BC-CS/PPF had good physical properties, which was attributed to the strong and uniform physical combination between nano-sized BC-CS and PPF. The sanitary products with BC-CS/PPF surface layer, denoted as BC-CS/PPF sanitary products, also had good absorption and anti-return property. The antibacterial test revealed that BC-CS had an excellent performance against S. aureus and E. coli in the simulated application environment. Moreover, the antibacterial performance was better than that of commercial sanitary products.

polymer science,chemistry, organic, applied
Mechanical Properties and Water Absorption of Alginate/hydroxypropyl Methyl Cellulose Blend Membranes with Semi-interpenetrating Network

Qianqian Wang,Gangqiang Zhang,Lin Zhang,Ping Zhu

DOI: https://doi.org/10.1007/s12221-020-9854-3

IF: 2.5

2020-07-01

Fibers and Polymers

Abstract:Sodium alginate (SA) is a renewable material with broad application prospects in textiles, medicine, and other fields. However, the disadvantage of poor strength and brittleness limited its future application. In this work, the SA was reinforced by the hydroxypropyl methyl cellulose (HPMC) with a semi-interpenetrating network which leverages the favourable properties. The structure and surface morphology of SA/HPMC blend membranes after Ca ion cross-linking were examined by FTIR, Raman, XRD and SEM. The mechanical properties and water absorbency of the blend membranes were also studied. The results indicated that the hydrogen bond was found in SA/HPMC blend membranes, which improved the SA/HPMC blend membranes stability. Compared with calcium alginate membrane, the tensile strength and elongation at break of SA/HPMC blend membranes were improved to 57 % and 400 %, respectively.

materials science, textiles,polymer science
Preparation of Nanocomposite Superabsorbents Based on Hydrotalcite and Poly(acrylic-Co-acrylamide) by Inverse Suspension Polymerization

Yatao Zhang,Lihai Fan,Pengzhan Zhao,Lin Zhang,Huanlin Chen

DOI: https://doi.org/10.1163/156855408786778320

IF: 2.839

2008-01-01

Composite Interfaces

Abstract:Firstly, hydrotalcite (HT) was synthesized by the urea method. Then, sodium methyl allyl sulfonate (SMAS) was used as intercalation agent to prepare intercalated HT (SMAS-HT). Finally, a novel poly(acrylic-co-acrylamide)/HT nanocomposite superabsorbent was prepared by inverse suspension polymerization, using N,N'-methylenebisacrylamide (NMBA) as a cross-linking agent and potassium persulfate (KPS) as an initiator. The morphology of the superabsorbents was characterized by FT-IR, XRD, SEM and TEM. The influences of the amount of SMAS-HT on the water (salt) absorbency were investigated. Results showed that the intercalation was successful and the intercalated SMAS-HT incorporated into the superabsorbent was completely exfoliated. The superabsorbent particles approach a spherical shape and the average size is 200-300 nm. The particle sizes of the superabsorbents decrease with increasing the content of SMAS-HT. In addition, the superabsorbent acquired its highest water (salt) absorbency when the content of SMAS-HT is 3 wt%. The highest absorbencies of the superabsorbent for deionized water and 0.9% NaCl(aq) were 900 g/g and 140 g/g, respectively.
Cellulose nonwoven with fast liquid-discharging and anti-return properties: A microplastic-free surface layer for disposable absorbent hygiene products

Mei Liu,Chi Ma,Yong Chen,Yaning Wang,Jielin Xu,Zhenguang Li,Lili Deng,Liming Zou,Jing Wu,Huaping Wang

DOI: https://doi.org/10.1016/j.cej.2024.151291

IF: 15.1

2024-04-28

Chemical Engineering Journal

Abstract:Nowadays, the waste of non-biodegradable disposable absorbent hygiene products (DAHPs) has become one of the biggest solid waste in landfills. In this work, the cellulose nonwovens (CNW) were adopted to develop fully biodegradable, microplastic-free surface layer for DAHPs. To achieve this goal, the high hydrophilicity and lack of antibacterial properties were tackled by simultaneously grating tert -butyl isocyanate (TBIS) and anchoring nano zinc oxide (nano-ZnO) on the CNW substrate via a two-step process. The urethane groups formed between cellulose and TBIS strongly coordinates with nano-ZnO, pivotally constructing a cellulose-based surface with moderately-high hydrophobicity with a water contact angle (WCA) of 139.7°, superior antibacterial rates (> 90% against Escherichia coli and Staphylococcus aureus ), an excellent air-permeability (2621 mm·s - 1 ) and a good breaking strength (66.9 N·5cm - 1 ). Compared with the commercial sanitary products, the assembled sanitary product with laser-meshed cellulose surface exhibits an even faster liquid discharging ability ( 96%). This innovative, functional cellulose-based fabric holds immense potential for application as sustainable, and microplastic-free surface layer of DAHPs.

engineering, chemical, environmental
Toward sustainable menstrual health management: focus on super absorbent polymers

Refilwe Mogale,Marietjie Schutte-Smith,Elizabeth Erasmus,Kantinka De Wet,Hendrik G. Visser

DOI: https://doi.org/10.1007/s10853-024-09519-2

IF: 4.5

2024-04-15

Journal of Materials Science

Abstract:In low- to middle-income communities, the lack of affordability of conventional sanitary products during menstrual cycles can cause psychological and health issues, ultimately affecting their quality of life. It is crucial to develop alternative products that are affordable and accessible to all while also promoting menstrual health and hygiene. Super absorbent polymers (SAPs) are a vital component in current disposable sanitary pads and nappies. However, these SAPs are often non-biodegradable and non-biocompatible. Therefore, the use of eco-friendly materials for the production of SAPs is gaining popularity in the hygiene industry, as it offers a means to reduce the carbon footprint and environmental impact associated with traditional SAPs made from non-renewable petroleum-based materials. SAPs made from polysaccharides often have naturally occurring antibacterial properties, making them appealing for commercial applications in sanitary products such as sanitary pads. In addition, the move toward reusable sanitary pads with antibacterial properties can significantly reduce waste generated by single-use products and prevent the growth of bacteria, improving the safety and hygiene of the product. Furthermore, computational modeling and artificial intelligence are now important tools in SAP synthesis, providing advantages such as predicting polymer properties, rationalizing synthesis pathways, and improving quality control. These tools can reduce synthesis costs by eliminating the need for trial-and-error approaches in polymer synthesis, ultimately promoting more affordable products for end users. Overall, these advancements in polymer synthesis and material design can help to create a more sustainable industry and promote menstrual hygiene and product accessibility to those who need it most.

materials science, multidisciplinary
Response Surface Method Based Modeling and Optimization of CMC-g Terpolymer Interpenetrating Network/Bentonite Superabsorbent Composite for Enhancing Water Retention

Shimaa Mohamed Elsaeed,Elsayed Gamal Zaki,Ahmed Abdelhafes,Ayman S Al-Hussaini

DOI: https://doi.org/10.1021/acsomega.1c03194

IF: 4.1

2022-03-04

ACS Omega

Abstract:Water shortages have become a serious issue, so the importance of developing innovative cellulose-based superabsorbent polymer (SAP) was experimentally assessed as an environmentally friendly alternative to acrylate-based SAPs for the optimization of water consumption. The development of a biodegradable superabsorbent hydrogel composite based on a graft copolymer of carboxymethyl cellulose (CMC) and mixtures of different comonomers such as an acrylamide-co-acrylic acid-co-2-acrylamido-2-methylpropanesulfonic acid (Am-co-AA-co-AMPS) CMC-g-TerPoly interpenetrating network was characterized by infrared spectroscopy (FT-IR), scan electron microscopy (SEM), atomic force microscope (AFM), thermal gravimetric analysis (TGA), and swelling capacity in different aqueous media. The optimized CMC-g-(TerPoly) composite showing outstanding superabsorbance with high water retention, the ratio of constituents, temperature, and pH effect on equilibrium swelling have been optimized by using multistage response surface methodology (RSM). In distilled water (d-water), the equilibrium water absorption capacity (EW) of the synthesized composite hydrogels (SAP-IPN1) is 1200 g (d-water/1g hydrogel) which is superior to any other commercial polyacrylate SAP hydrogels, while in saline water the EW is 650 g (s-water/1g hydrogel). The performance of the SAP-IPN for water retention was evaluated by studying several swelling/deswelling cycle measurements. The prepared SAP-IPN hydrogels were found to show pH and salt solution dependence on the swelling behavior. The new SAP-IPN can work with commercial SAP, which is recommended for application as a water reservoir in arid land for irrigation for agriculture purposes.
An approach of pectin from Citrus aurantium L. for superabsorbent resin with superior quality for hygiene products: Salt resistance, antibacterial, nonirritant and biodegradability

Peng Zhou,Xiangzhou Li,Zhi Jiang,Jun Zhou,Guang He,Limin Qu

DOI: https://doi.org/10.1016/j.ijbiomac.2022.12.131

2023-02-01

Abstract:In this paper, a kind of superabsorbent resin (SAR) with superior quality for hygiene products was developed using Fructus Aurantii Immaturus pectin (FAIP) from Citrus aurantium L.. FAIP-g-AM/AMPS SAR was established by free radical graft co-polymerization with FAIP as skeleton structure, N, N'-Methylene-bis (acrylamide) (MBA) as the cross-linker. Meanwhile, the functional monomers of acrylamide (AM) and 2-acrylamido-2-methylpropane sulfonic acid (AMPS) were introduced. The structure and morphology of FAIP-g-AM/AMPS were characterized by FTIR, 13C NMR, XRD, SEM and TG-DSC analysis. The results confirmed that the AFIP-g-AM/AMPS SAR was successfully prepared, which exhibited a three-dimensional (3D) network structure and an excellent thermal stability. The absorption and retention capacity of FAIP-g-AM/AMPS was comparable to or even better than commercial diapers and sanitary napkins. Significantly, FAIP-g-AM/AMPS itself exhibited excellent antibacterial and safety. FAIP-g-AM/AMPS has an inhibition ratio of 97.1 % for Escherichia coli (E. coli) and 98.5 % for Staphylococcus aureus (S. aureus), and was non-irritating and non-allergic to the skin. In addition, FAIP-g-AM/AMPS presented amazing biodegradability and a weight loss reached 37.1 % after 30 days by soil burial test. The research provides a safe and high-performance SAR, which expected to be used in hygiene products such as baby diapers, adult incontinence pads and sanitary napkins.
Synthesis, characterization, and swelling kinetic study of porous superabsorbent hydrogel nanocomposite based on sulfonated carboxymethylcellulose and silica nanoparticles

Ali Olad,Hamid Zebhi,Dariush Salari,Abdolreza Mirmohseni,Adel Reyhanitabar

DOI: https://doi.org/10.1007/s10934-017-0543-6

2017-12-04

Journal of Porous Materials

Abstract:New superabsorbent nanocomposite was synthesized by free-radical graft polymerization of sulfonated-carboxymethyl cellulose (SCMC) with acrylic acid (AA) in the presence of polyvinylpyrrolidone (PVP) and silica nanoparticles. Carboxymethyl cellulose (CMC) was first sulfonated using chlorosulfonic acid, and then AA monomers were grafted onto SCMC. FTIR results confirmed that sulfonation of CMC as well as grafting of AA monomers onto SCMC has been performed successfully. Moreover, the presence of silica nanoparticles into superabsorbent nanocomposite was evaluated with EDX analysis. The element mappings show a homogenous distribution of silica nanoparticles throughout the hydrogel nanocomposite. SEM images exhibited porous morphology for hydrogel nanocomposite, which was due to the incorporation of PVP in its network. The experimental findings from TGA analysis indicated that incorporation of PVP and silica nanoparticles into the hydrogel network improved thermal stability of superabsorbent nanocomposite. Swelling kinetic studies revealed that superabsorbent nanocomposite hydrogel had higher equilibrium swelling capacity and swelling rate compared with the neat hydrogel sample. Besides that, superabsorbent nanocomposite depicted excellent salt and pH-sensitive behavior in different saline and pH solutions. As a consequence, this hydrogel nanocomposite acts as useful water reservoir, which might be most profitable in agricultural applications.

materials science, multidisciplinary,chemistry, physical, applied

[Neurologic and encephalographic syndrome of hyperbarism].

Preparation and Characterization of Sulfated Carboxymethyl Cellulose Nanofiltration Membranes with Improved Water Permeability

Multiporous Microstructure for Enhancing the Water Absorption and Swelling Rate in Poly(sodium Acrylic Acid) Superabsorbent Hydrogels Based on a Novel Physical and Chemical Composite Foaming System

Enhancing the efficacy of feminine hygiene sanitary napkins by developing a super absorbent polymer based on methyl methacrylate and methacrylic acid

Formulation and characterization of super absorbent copolymer AA, ACN-grafted sodium acrylate for feminine napkin

Novel Degradable Superabsorbent Polymers Based on Carboxymethyl Cellulose

Development of biopolymer-based menstrual pad and quality analysis against commercial merchandise

Synthesis and Characterization of Silk Sericin/Acrylic Acid/Acrylamide Superabsorbent Polymer

Development of essential oil-containing antimicrobial and deodorizing nanofibrous membranes for sanitary napkin applications

Biocompatible Cellulose-Based Superabsorbents for Personal Care Products

Synthesis and Properties of Acrylic-Based Superabsorbents with Enhanced Crosslinking on Particle Surface

Dynamic Doppler Frequency Shift Errors: Measurement, Characterization, and Compensation

Synthesis and characterization of reinforced acrylic-based superabsorbents crosslinked with divinylbenzene

Asymmetric wetting and antibacterial composite membrane obtained by spraying bacterial cellulose grafted with chitosan for sanitary products surface layers

Mechanical Properties and Water Absorption of Alginate/hydroxypropyl Methyl Cellulose Blend Membranes with Semi-interpenetrating Network

Preparation of Nanocomposite Superabsorbents Based on Hydrotalcite and Poly(acrylic-Co-acrylamide) by Inverse Suspension Polymerization

Cellulose nonwoven with fast liquid-discharging and anti-return properties: A microplastic-free surface layer for disposable absorbent hygiene products

Toward sustainable menstrual health management: focus on super absorbent polymers

Response Surface Method Based Modeling and Optimization of CMC-g Terpolymer Interpenetrating Network/Bentonite Superabsorbent Composite for Enhancing Water Retention

An approach of pectin from Citrus aurantium L. for superabsorbent resin with superior quality for hygiene products: Salt resistance, antibacterial, nonirritant and biodegradability

Synthesis, characterization, and swelling kinetic study of porous superabsorbent hydrogel nanocomposite based on sulfonated carboxymethylcellulose and silica nanoparticles