Abstract:Purpose: The aim of the proposed research is to establish experimentally the relation between damaging of the tread surface of model wheels and the characteristics of fatigue crack growth resistance of wheel steels "KI th, "KII th, "KI fc, "KII fc), depending on its microstructure. Design/methodology/approach: Characteristics of the fatigue crack growth resistance have been determined on the specimens cut out from the hot rolled plate of thickness 10 mm of the steel which is an analogue of railway wheel steels. To obtain different steel microstructures and its strength level, test specimens were quenched (820°C, in oil) and then tempered at 400°C, 500°C, and 600°C for 2 h. The characteristics of Mode I fatigue crack growth resistance of steel were determined on the basis of fatigue macrocrack growth rate diagrams da/dN–"KI, obtained by the standard method on compact specimens with the thickness of 10 mm at a frequency of 10-15 Hz and the stress ratio R = 0.1 of the loading cycle. The characteristics of Mode II fatigue crack growth resistance were determined on the basis of da/dN–"KII diagrams, obtained by authors method on edge notched specimens with the thickness 3.2 mm at a frequency of 10-15 Hz and R = –1 taking account of the crack face friction. The hardness was measured with a TK-2 hardness meter. Zeiss-EVO40XVP scanning electron microscope was used for microstructural investigations. Rolling contact fatigue testing was carried out on the model specimens of a wheel of thickness 8 mm and diameter 40 mm in contact with a rail of length 220 mm, width 8 mm and height 16 mm. Wheels were manufactured form the above-described steel after different treatment modes. Rails were cut out from a head the full-scale rail of hardness 46 HRC. The damaging was assessed by a ratio of the area with gaps formed by pitting and spalling to the general area of the wheel tread surface using a special stand. Findings: The growth of the damage of the tread surface of the model wheels correlates uniquely with the decrease of the cyclic fracture toughness of the wheel steel "KI fc and "KII fc, determined at Mode I and Mode II fracture mechanisms. These characteristics of the wheel steel can be considered as the determining parameter of this process, in contrast to the fatigue thresholds "KI th and "KII th. Research limitations/implications: Investigations were conducted on model wheels that simulate the damage of real railway wheels tread surface. Practical implications: A relationship between the damage of tread surface of railway wheels and the strength level of wheel steels is determined. Originality/value: The damage of the tread surface of the model wheels during the rolling contact fatigue of the pair wheel-rail increases with the growth of the strength (hardness) of the wheel steel, which corresponds to the statistical data of the operation of the real railway wheels.

Durability of Railroad Car Wheelset Axles of RU1Sh Type Repaired by Explosion Welding

Relationships between the fatigue crack growth resistance characteristics of a steel and the tread surface damage of railway wheel

Rolling Contact Fatigue Damage in Welded Rail Steel Joints

Repair of light rail track through restoration of the worn part of the railhead using submerged arc welding process

Influence of wheel polygonal wear on wheel-rail dynamic contact in a heavy-haul locomotive under traction conditions

Structure and Mechanical Properties of the Heat-Affected Zone of Restored Railway Wheels

Fatigue life enhancement of foreign object impacted railway axle EA4T steel with surface shot peening

Assessment of Durability of the Rail Vehicle Components with the Use of Degradation Analysis Method

Damage and Fatigue Life Evaluation for Laser Cladding Remanufactured Wheel

Mechanical and Tribological Behaviors of U75VG Rail Flash−Butt Welded Joint

Evolution Characteristics of Aluminum Thermal Weld Irregularity and Damage in Heavy-Haul Railway under Different Service Conditions

Evolution of microscopic characteristics of rolling contact fatigue coexisting with wear of U75V rail

Influence of P2 resonance of metro wheel–rail system on fatigue failure of rail fastening clips

Study of wear resistance of railway rails welded joint

Influence of artificial defects on fatigue strength of induction hardened S38C axles

STRUCTURAL CHANGES DURING THERMAL STRENGTHENING OF THE RAILWAY WHEEL

Experimental Studies of Welded Joints in Structures Subject to High Impact Vibrations Using Destructive and Non-Destructive Methods

Fatigue assessment of EA4T railway axles under artificial surface damage

Failure analysis of the rotating shaft in the rail grinding car

Experimental Investigation on the Wear and Damage Behaviors of Machined Wheel-Rail Materials under Dry Sliding Conditions

Evaluation of Mechanisms for Strengthening of Surface Layers of Long Rails in Different Directions Under Continuous Operation